Yamaha DD-12 Le manuel du propriétaire

Marque: Yamaha

Modèle: DD-12

Catégorie: Batterie de musique

Taper: Le manuel du propriétaire

Ce manuel convient également à

DD-65
YDD-60

Owner’s Manual

Digital Percussion

DD-65/YDD-60 Owner’s Manual

PLEASE KEEP THIS MANUAL

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or speciﬁcally

recommended by Yamaha.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change or mod-

ify any of the speciﬁcations without notice or obligation to update exist-

ing units.

This product, either alone or in combination with an ampliﬁer and head-

phones or speaker/s, may be capable of producing sound levels that

could cause permanent hearing loss. DO NOT operate for long periods

of time at a high volume level or at a level that is uncomfortable. If you

experience any hearing loss or ringing in the ears, you should consult

an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and consult your

dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the pro-

duction methods used to produce them, meet these goals. In keeping

with both the letter and the spirit of the law, we want you to be aware of

the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of

battery is approximately ﬁve years. When replacement becomes neces-

sary, contact a qualiﬁed service representative to perform the replace-

ment.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, do not mix batteries with new, or with batter-

ies of a different type. Batteries MUST be installed correctly. Mis-

matches or incorrect installation may result in overheating and battery

case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all bat-

teries away from children. Dispose of used batteries promptly and as

regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some rea-

son its useful life is considered to be at an end, please observe all local,

state, and federal regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc. If your dealer is unable to assist

you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the date

of purchase in the spaces provided below and retain this manual as a

permanent record of your purchase.

Model

Serial No.

Purchase Date

SPECIAL MESSAGE SECTION

92-BP (bottom)

DD-65/YDD-60 Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please contact

Yamaha Corporation of America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

(class B)

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den

ar ansluten till vägguttaget, även om själva apparaten har stängts av.

ADVARSEL: Netspæendingen til dette apparat er IKKE afbrudt,

sålæenge netledningen siddr i en stikkontakt, som er t endt — også

selvom der or slukket på apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko

laitetta verkosta.

(standby)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in accor-

dance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured makings identifying the ter-

minals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the ter-

minal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal

of the three pin plug.

• This applies only to products distributed by Yamaha-Kemble

Music (U.K.) Ltd.

(2 wires)

Entsorgung leerer Batterien (nur innerhalb Deutschlands)

Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte Batterien

oder Akkumulatoren dürfen nicht in den Hausmüll. Sie können bei

einer Sammelstelle für Altbatterien bzw. Sondermüll abgegeben wer-

den. Informieren Sie sich bei Ihrer Kommune.

(battery)

DD-65/YDD-60 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use the speciﬁed adaptor (PA-5D, PA-150 or an equivalent recommended by

Yamaha) only. Using the wrong adaptor can result in damage to the instrument

or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• Do not place the AC adaptor cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy objects

on it, or place it in a position where anyone could walk on, trip over, or roll

anything over it.

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into

any openings. If any liquid such as water seeps into the instrument, turn off the

power immediately and unplug the power cord from the AC outlet. Then have the

instrument inspected by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

• If the AC adaptor cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the instrument, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power switch,

disconnect the adaptor plug from the outlet, and have the instrument inspected

by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord.

• Unplug the AC power adaptor when not using the instrument, or during

electrical storms.

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• Always make sure all batteries are inserted in conformity with the +/- polarity

markings. Failure to do so might result in overheating, ﬁre, or battery ﬂuid

leakage.

• Always replace all batteries at the same time. Do not use new batteries together

with old ones. Also, do not mix battery types, such as alkaline batteries with

manganese batteries, or batteries from different makers, or different types of

batteries from the same maker, since this can cause overheating, ﬁre, or battery

ﬂuid leakage.

• Do not dispose of batteries in ﬁre.

• Do not attempt to recharge batteries that are not intended to be charged.

• When the batteries run out, or if the instrument is not to be used for a long time,

remove the batteries from the instrument to prevent possible leakage of the

battery ﬂuid.

• Keep batteries away from children.

• If the batteries do leak, avoid contact with the leaked ﬂuid. If the battery ﬂuid

should come in contact with your eyes, mouth, or skin, wash immediately with

water and consult a doctor. Battery ﬂuid is corrosive and may possibly cause

loss of sight or chemical burns.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disﬁguration or damage to the internal

components.

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Otherwise, the instrument, TV, or radio may

generate noise.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor

Battery

Location

(4)-12 1/2

DD-65/YDD-60 Owner’s Manual

• Before moving the instrument, remove all connected adaptor and other cables.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the

power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

• Do not place objects in front of the instrument’s air vent, since this may prevent

adequate ventilation of the internal components, and possibly result in the

instrument overheating.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum. Also, be sure to set the volumes of all

components at their minimum levels and gradually raise the volume controls

while playing the instrument to set the desired listening level.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning ﬂuids, or chemical-impregnated wiping cloths.

• Do not insert a ﬁnger or hand in any gaps on the instrument.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

Backing up your data

• Saved data may be lost due to malfunction or incorrect operation. Save the

important data to your computer. For information on sending the data, see page

36.

Always turn the power off when the instrument is not in use.

When using a power adaptor, even when the power switch is in the “STANDBY” position, electricity is still ﬂowing to the instrument at the minimum level. When you are not

using the instrument for a long time, make sure you unplug the AC power adaptor from the wall AC outlet.

Make sure to discard used batteries according to local regulations.

● COPYRIGHT NOTICE

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license

to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style ﬁles, MIDI ﬁles, WAVE data, musical

scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws.

Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your

personal use.

● Trademarks

• The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective companies.

Connections

Maintenance

Handling caution

Saving data

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

The illustrations and LED displays as shown in this owner’s manual are for instructional purposes only, and may appear somewhat different from those on

your instrument.

(4)-12 2/2

DD-65/YDD-60 Owner’s Manual

Congratulations!

Thank you for purchasing the Yamaha DD-65/YDD-60.

The DD-65/YDD-60 has been developed to

respond and play like a drum set—

but with greater ease, ﬂexibility and sophisticated functions.

Before you use the instrument, we recommend that

you carefully read through this manual.

The DD-65/YDD-60 is a sophisticated yet easy-to-use instrument with the following features and functions.

■ Select and play 254 different percussion sounds

A wide variety of percussion voices is available, letting you play different sounds when you

hit the pads—for example, changing a pad to play a snare, tom, conga or even special sound

effects, such as a door slam or a lion’s roar.

■ Select and play 100 different Songs

The 100 songs include Demos, Drum patterns and Fill in patterns. You can mute the individual

parts and play the muted part on the pads and pedals yourself.

■ Record your own performance

Up to ﬁve of your performances can be saved to this instrument, and these songs can be played

in the same manner as the preset songs.

Main features

● Supplied accessories

• Drum Stick (x2)

• Foot Pedal 1 & 2

• Owner’s Manual

DD-65/YDD-60 Owner’s Manual

Main features ........................................................6

Setting Up 8

Power Requirements ............................................8

Panel Controls 10

Playing the Demo Song 12

Adjusting the volume...........................................12

SONG VOLUME .................................................12

Play the Pads/Pedals 13

Pad Names .........................................................13

Setting the Hand Percussion ON/OFF................14

Lock the Hand Percussion ON............................14

Selecting a Drum Kit and play it..........................15

Assigning Voices to Individual Pads and Pedals

and saving to a Custom Kit (“

CO1

–

CO3

”).......16

Setting the Reverb ON/OFF................................17

Setting the Reverb type ......................................17

Setting the Pad Sensitivity ..................................18

Setting the Click ON/OFF ...................................19

Setting the Time Signature of the Click...............19

Setting Equalization On/Off.................................21

Playing a Song 22

Selecting and playing a Song .............................22

Tap Start .............................................................23

Pad Start .............................................................23

Setting the Auto Kit Select ON/OFF....................24

Adjusting the Tempo ...........................................25

Play along with a Song 26

Setting the Track ON/OFF ..................................26

Break...................................................................26

Using A-B Repeat ...............................................27

Recording a Song 28

Recording............................................................28

Playing the recorded song ..................................29

Song Clear ..........................................................29

About MIDI 30

What is MIDI?..................................................... 30

What You Can Do With MIDI ............................. 30

Transferring Performance Data To and From

Another Instrument ....................................... 30

Local ON/OFF .................................................... 31

Setting the MIDI Note Number ........................... 32

MIDI Note Number Auto Selection ON/OFF ...... 33

Transferring Song files to and from

a connected computer .................................. 34

Appendix 36

Backup and Initialization .................................... 36

Troubleshooting ................................................. 37

Drum Voice List.................................................. 38

Song List ............................................................ 40

Drum Kit List....................................................... 41

Voice List............................................................ 44

Drum Map .......................................................... 48

MIDI Implementation Chart ................................ 52

Specifications ..................................................... 55

Drum Score ........................................................ 56

Contents

DD-65/YDD-60 Owner’s Manual

Setting Up

Be sure to do the following operations BEFORE turning on the power.

Although the instrument will run either from an optional AC adaptor or batteries, Yamaha recom-

mends use of an AC adaptor whenever possible. An AC adaptor is more environmentally friendly

than batteries and does not deplete resources.

q Make sure that the power of the instrument

is off (display shows no indications).

• Use the speciﬁed adaptor (PA-5D, PA-150, or an equivalent

recommended by Yamaha) only. The use of other adaptors

may result in irreparable damage to both the adaptor and the

instrument.

w Connect the AC adaptor to the power supply jack.

e Plug the AC adaptor into an AC outlet.

• Unplug the AC Power Adaptor when not using the instru-

ment, or during electrical storms.

•Never interrupt the power supply (e.g. remove the batteries

or unplug the AC adaptor) during any DD-65/YDD-60 record

operation! Doing so can result in a loss of data.

• Even when the instrument is turned off, electricity is still

ﬂowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make

sure you unplug the AC power adaptor from the wall AC out-

let.

q Open the battery compartment cover located

on the instrument’s bottom panel.

w Insert the six new alkaline batteries, being

careful to follow the polarity markings on

the side of the compartment.

e Replace the compartment cover, making

sure that it locks ﬁrmly in place.

•Never connect or disconnect the AC power adaptor when the

power is on and the batteries are installed. Doing so will turn

the power off.

For battery operation the instrument requires six 1.5V

“C” size, LR14 or equivalent batteries. (Alkaline bat-

teries are recommended.) When battery power

becomes too low for proper operation, the volume

may be reduced, the sound may be distorted, and

other problems may occur. When this happens, make

sure to replace all batteries, following the precautions

listed below.

• Use alkaline batteries for this instrument. Other types of bat-

teries (including rechargeable batteries) may have sudden

drops of power when battery power becomes low.

• Make sure to install the batteries with the proper orientation,

maintaining the correct polarity (as shown). Incorrect battery

installation may result in heat, ﬁre and/or leaking of corro-

sive chemicals.

• When the batteries run down, replace them with a complete

set of six new batteries. NEVER mix old and new batteries.

Do not use different kinds of batteries (e.g. alkaline and man-

ganese) at the same time.

• If the instrument is not to be in use for a long time, remove

the batteries from it, in order to prevent possible ﬂuid leak-

age from the battery.

Power Requirements

Using an AC Power Adaptor

Using Batteries

WARNING

AC outlet

Adaptor

CAUTION

Setting Up

DD-65/YDD-60 Owner’s Manual

The DD-65/YDD-60 speakers are automatically shut

off when a plug is inserted into this jack. The

PHONES/OUTPUT jack also functions as an external

output.

You can connect the PHONES/OUTPUT jack to a

keyboard ampliﬁer, stereo system, mixer, tape

recorder, or other line-level audio device to send the

instrument’s output signal to that device.

•Avoid listening with the headphones at high volume for long

periods of time; doing so may not only result in ear fatigue, it

may be damaging to your hearing.

•To prevent damage to the speakers, set the volume of the

external devices at the minimum setting and turn power off

the devices before connecting them. Failure to observe these

precautions may result in electric shock or equipment dam-

age. Also, be sure to set the volumes of external devices at

their minimum levels and gradually raise the volume controls

while playing the instrument to set the desired listening

level.

This jack is for connection to an external audio

source. You can play the instrument with backing

music and accompaniment, like playing with a full

band. Adjust the input level from the volume control

of the external audio source for optimum balance.

These jacks for connection of the Pedal 1 or Pedal 2

footswitches. These pedals can be used simulta-

neously play the drum set’s hi-hat pedal or bass drum

voices—or they can also be assigned to play other

voices as well. Connect the supplied Pedal 1 to the

PEDAL 1 jack and Pedal 2 to the PEDAL 2 jack.

• Make sure that the pedal plugs are properly con-

nected to the PEDAL jacks before turning on the

power.

The instrument also features MIDI terminals, allow-

ing you to interface the instrument with other MIDI

instruments or computers. (For more information, see

page 30.)

• MIDI cables (sold separately) must be used for con-

necting to MIDI devices. They can be bought at music

stores, etc.

• Always use a high-quality MIDI cable to connect MIDI

OUT to MIDI IN terminals. Never use MIDI cables

longer than about 15 meters, since cables longer than

this can pick up noise which can cause data errors.

Turn down the volume by turning the [MASTER

VOLUME] control to the left and press the

[STANDBY/ON] switch to turn on the power. Press

the [STANDBY/ON] switch again to turn the power

off.

• Even when the switch is in the “STANDBY” position, electric-

ity is still ﬂowing to the instrument at the minimum level.

When you are not using the DD-65/YDD-60 for a long time,

make sure you unplug the AC power adaptor from the wall

AC outlet, and/or remove the batteries from the instrument.

•Never interrupt the power supply (e.g. remove the batteries

or unplug the AC adaptor) during any record operation on

the instrument! Doing so can result in a loss of data.

• While the data is being recorded (“-”appears and moves from

left to right on the display), never interrupt the power supply

(e.g., remove the batteries or unplug the AC adaptor). Doing

so can result in a loss of data.

Connecting headphones (PHONES/OUTPUT Jack)

Connecting an audio source (AUX IN Jack)

Connecting Pedals 1 and 2

WARNING

CAUTION

Pedal 1 Pedal 2

Using the MIDI Terminals

Turn on the power

NOTE

other MIDI instrument

NOTE

CAUTION

DD-65/YDD-60 Owner’s Manual

Panel Controls

Front Panel

[MASTER VOLUME] control..................... 12

DIAL........................................................... 15

[ASSIGN] button....................................... 16

[REVERB] button...................................... 17

[HAND PERC.] button .............................. 14

[KIT] button............................................... 15

[CLICK] button.......................................... 19

[SONG] button .......................................... 22

[TEMPO] button........................................ 25

PART MUTE [DRUM 1–3], [BACKING]

buttons ...................................................... 26

[FUNCTION] button .................................. 12

[DEMO] button.......................................... 12

[STANDBY/ON] button ....................... 12, 36

[REC] button ............................................. 28

[BREAK/TAP] button .......................... 23, 26

[A-B REPEAT] button............................... 27

[START/STOP] button ........................ 12, 22

DISPLAY.................................................... 15

DRUM PAD x 8 .......................................... 13

001

!2 !3!1

!56

● Front Panel

Indicates the song number when power is turned on.

Panel Controls

DD-65/YDD-60 Owner’s Manual

Rear Panel

@0 [DC IN 12V] (AC Adaptor) jack .................. 8

@1 [AUX IN] jack............................................... 9

@2 [PHONES/OUTPUT] jack............................ 9

@3 [PEDAL 2] Jack........................................... 9

@4 [PEDAL 1] Jack........................................... 9

@5 [MIDI IN/OUT] Terminals....................... 9, 30

@0@1@2@3@4@5

● Rear Panel

Pedal 2Pedal 1

• Since speakers are built into the DD-

65/YDD-60, you should be careful to

never leave any video tapes, cassette

tapes, ﬂoppy disks or any kind of

magnetic storage media on the

panel—doing so may result in data

loss or damage to the items. Also

avoid using the DD-65/YDD-60 near a

television or computer monitor, since

interference may result.

• Use the sticks with caution. Do not

use them for anything other than play-

ing the instrument. Also, to avoid

damage or injury, refrain from waving

them recklessly or throwing them.

CAUTION

● Drum Sticks

● Using the Foot Pedals (1/2)

When connected, these pedals can be used

simultaneously play the drum set’s hi-hat pedal

or bass drum voices—or they can also be

assigned to play other voices as well. Connect

the supplied Pedal 1 to the PEDAL 1 jack @4 and

Pedal 2 to the PEDAL 2 jack @3.

• Make sure that the pedal plugs are properly connected

to the PEDAL jacks before turning on the power.

• Do not press the pedals while turning the power on.

Doing this changes the recognized polarity of the

pedal, resulting in reversed pedal operation.

•Avoid using the pedals directly on a soft ﬂoor, since

they may scratch the surface of the ﬂoor.

•Avoid getting caught in or tripping over the pedal

cords; this may cause the instrument to fall and result

in damage or injury.

CAUTION

DD-65/YDD-60 Owner’s Manual

Playing the Demo Song

The DD-65/YDD-60 features several demonstration songs (001–005), specially created

to show you the dynamic possibilities of the instrument.

1 Turn on the power.

2 Start the Demo Song.

3 Stop the Demo Song.

Turn on the [STANDBY/ON] switch on.

• Even when the switch is in the “STANDBY” position, electricity is still ﬂowing to

the instrument at the minimum level. When you are not using the DD-65/YDD-60

for a long time, make sure you unplug the AC power adaptor from the wall AC

outlet, and/or remove the batteries from the instrument.

Press the [DEMO] button and the demo song starts playing.

To stop playback, press the [DEMO] button again or press the

[START/STOP] button.

● Adjusting the volume

Turn the [MASTER VOLUME] control.

● SONG VOLUME

The SONG VOLUME can be used to adjust the balance

between the song accompaniment and your own perfor-

mance on the pads.

Enter the Function mode by pressing the [FUNCTION]

button, then press the [DRUM 1] or [DRUM 2] button a

number of times until the “SGL” item appears. The current

Song volume appears when it is released.

To raise the value, turn the DIAL to the right (clockwise),

and to lower it, turn the DIAL to the left (counter-clock-

wise). Volume range is from 0 to 127.

Exit from the Function mode by pressing the [FUNCTION]

button.

• The [DRUM 1] and [DRUM 2] buttons change the selected

order of the function item.

CAUTION

Decreases

the overall

volume.

Increases

the overall

volume.

SGL

NOTE

DD-65/YDD-60 Owner’s Manual

Play the Pads/Pedals

Strike the pad with the supplied drum sticks or your hands to play the drum voices.

When playing the pads with your hands, turn the Hand Percussion feature on by press-

ing the [HAND PERC.] button (the lamp lights).

The volume of the pads’ sounds responds to your playing; when you play soft the vol-

ume is soft, and when you play strongly the volume is loud.

The actual loudness of the sound may vary according to which part of the pad is

struck.

Pad Names

Pedal 1 features touch response; the

volume responds to how hard you

press the pedal.

• If your pressing of the

pedal is too slow or soft,

there may be no sound.

NOTE

A hi-hat sound is assigned to Small Pad 2 (Drum

Kit 1). Striking Small Pad 2 while pressing Pedal

2 produces a closed hi-hat sound.

Striking the Pad 2 without pressing the pedal

produces an open hi-hat sound.

Pad 2

52: Tom Power 6

Small Pad 3

116:

Ride Cymbal

Stereo 2

Small Pad 1

113:

Crash

Cymbal Stereo 1

Small Pad 2

100:

Hi-Hat

Closed Power 1

Pad 3

54: Tom Power 4

Pad 1

21: Snare Power 1

Pad 4

56: Tom Power 2

● Ex. shown, Drum Kit 1

Pedal 2

101: Hi-Hat Pedal Power

Pedal 1

3: Bass Drum Power Closed

Press Pedal 2 to control the Hi-

hat. (This is in the case of Drum

Kit 1.)

• When using Pedal

2, touch response

does not function.

NOTE

Small Pad 4

119:

Splash

Cymbal Stereo

Play the Pads/Pedals

DD-65/YDD-60 Owner’s Manual

You can play the pads of the instrument either with the supplied sticks or with your hands. Press and

set the following button when you play the instrument with your hands.

1 Press the [HAND PERC.] button.

If you perform on the instrument solely with your hands, we recommend that you use this operation

to lock the Hand Percussion so that it is always on. This protects the instrument from being inadvert-

ently changed during your performance.

1 Make sure that Hand Percussion is set to on (the

lamp is lit).

2 Set the Hand Percussion Lock to ON.

3 To turn off Hand Percussion Lock, press and hold

the [HAND PERC.] button until the “LOC” is no

longer shown on the display.

Setting the Hand Percussion ON/OFF

When you press the [HAND PERC.] button, the button’s lamp lights,

and the pad sensitivity is automatically adjusted for optimum playing

by hand. At the same time, an appropriate song (059) and drum kit(37)

are automatically called up.

When Hand Percussion is off, Song (001) and drum kit (01) are auto-

matically called up.

• Be sure to strike the pads only with your hands when HAND PERCUS-

SION is on, since the sensitivity is automatically set to appropriate level for

hand playing.

Lock the Hand Percussion ON

Press and hold the [HAND PERC.] button until “LOC” appears on the

display.

Hand Percussion on

NOTE

LOC

Press and hold

Play the Pads/Pedals

DD-65/YDD-60 Owner’s Manual

The instrument allows you to choose from 50 different Drum Kits (1–50: see the “Drum Kit List”

page 41) quickly and easily. 50 of the kits have preset voice combinations that will be set to the pads

and pedals when the kit is selected.

Select some different kits and try playing them.

The instrument also has three Custom Drum Kits allowing you to assign the desired voices to the

eight pads or two pedals (see “Assigning Voices to Individual Pads and Pedals and saving to a Cus-

tom Kit (“

CO1

–

CO3

”)” page 16).

1 Press the [KIT] button.

2 Select a Drum Kit Number.

Selecting a Drum Kit and play it

When you press the [KIT] button, the currently selected Drum Kit

number appears on the display.

Turn the DIAL to select a Drum Kit number. Drum Kit numbers will

increase as the DIAL is turned to the right (clockwise), and decrease

as the DIAL is turned to the left (counter-clockwise).

•Drum Kit number 1 is normally selected when the power is turned on.

• The “ CO1– CO3” Drum Kit are the Custom Kit.

* Custom Kits are those that you’ve assigned the desired voice to each

pad and pedal, then saved the entire assignments as a kit. (See “Assign-

ing Voices to Individual Pads and Pedals and saving to a Custom Kit

(“

CO1

–

CO3

”)” page 16.)

1 C01250 C03

NOTE

Play the Pads/Pedals

DD-65/YDD-60 Owner’s Manual

The instrument contains a total of 254 high quality drum sounds plus 25 drum phrases (see the

“Drum Voice List” page 38)—and you can assign these freely to each of the 8 drum pads and 2 ped-

als. Try assigning some different voices and save your own “CO1– CO3” Custom Drum Kits.

• Custom Kit “ CO1– CO3” and “ 01” drum kit contents are the same until modiﬁed (see the

“Drum Kit List” page 41).

1 Press the [ASSIGN] button.

2 Turn the dial and select a Custom Kit “CO1–CO3”

for saving.

3 Select a pad or pedal to be assigned.

4 Select a Voice Number.

Repeat the previous steps 3 and 4 for any or all of the pads and ped-

als.

Assigning Voices to Individual Pads and Pedals and saving to a Custom Kit (“

CO1

–

CO3

”)

When you press the [ASSIGN] button, the button’s lamp lights, and

“C01” appears on the display.

Strike any pad one time (or press a pedal), and the currently assigned

voice number for that pad/pedal is shown in the display.

You can select the voice by repeatedly striking the pad or repeatedly

pressing the pedal (while listening to the voice), or by turning the

DIAL.

● Striking the pad or pressing the pedal to select a voice.

Every time the pad is struck or a pedal is pressed, voice numbers will

increase by a value of one (1). In this method, you can hear and select

an assigned voice.

● Using the DIAL to select a voice.

Turn the DIAL to the right (clockwise), and voice numbers will

increase. Turn the DIAL to the left (counter-clockwise), and voice

numbers will decrease.

See the “Drum Voice List” on page 38.

NOTE

CO1

CO3CO2CO1

27912021

279119 20 21

Play the Pads/Pedals

DD-65/YDD-60 Owner’s Manual

5 Save to a Custom kit.

After you’ve assigned the voice, the instrument will automatically be

set to the assigned custom kit.

You can now play the voice you have assigned to the pad/pedal.

Different depths of the DD-65/YDD-60’s reverb effect can be added to the DD-65/YDD-60’s overall

sound.

1 Press the [REVERB] button.

2 To turn Reverb off, press the [REVERB] button

again. (Make sure that the lamp is not lit.)

1 Enter the Reverb type setting function.

2 Change the reverb type by turning the DIAL.

3 Press the [FUNCTION] button to exit from the

Function mode.

Press the [ASSIGN] button to save to a Custom kit (the lamp will be

off).

To cancel the saving, simply press the [KIT], [SONG] or [DEMO]

button.

Setting the Reverb ON/OFF

When you press the [REVERB] button the button’s lamp lights, and

the ambience of a room or concert hall is added to the sound.

Setting the Reverb type

Press the [FUNCTION] button once, then press the [DRUM 1] or

[DRUM 2] button a number of times until the “rbt” item appears.

The currently selected Reverb type number appears next to the “rbt”

indication.

CO1

Lamp is on

rbt

● R

ever

type

No. Reverb Type No. Reverb Type

1 Hall 1 6 Stage 1

2 Hall 2 7 Stage 2

3 Hall 3 8 Plate 1

4 Room 1 9 Plate 2

5 Room 2 10 Off

Play the Pads/Pedals

DD-65/YDD-60 Owner’s Manual

The instrument allows you to custom-set the sensitivity of the pads (range 0–2).

When set to a value of 2, the pad sensitivity is the highest, providing the most dynamic range for

your playing (softest to loudest volume).

1 Enter the Pad Sensitivity setting function.

2 Set the Sensitivity.

3 Exit from the Function mode by pressing the

[FUNCTION] button.

Setting the Pad Sensitivity

Press the [FUNCTION] button once, then press the [DRUM 1] or

[DRUM 2] button a number of times until the “SGL” item appears.

After a while, the current Sensitivity value appears next to the “SGL”

indication.

To raise the value, turn the DIAL to the right (clockwise), and to lower

it, turn the DIAL to the left (counter-clockwise).

• Default value is 1.

About the Pad Sound Mechanism

Each time you strike a pad, the sensor which is located at the bottom of the pad triggers an electronic signal and makes

a drum sound.

If you strike a pad too strongly, nearby sensors may also respond to the hit and trigger unwanted sounds. The DD-65/

YDD-60 is set to ignore weak signals from the pads in order to prevent inadvertent, unwanted sounds. However, this

may result in problems when intentionally striking two pads simultaneously. If one pad is struck strongly and the other

weakly, the pad struck weakly may not sound (even though you want it to).

To solve this, you can change the DD-65/YDD-60 settings or alter your playing technique (as described below).

● Striking two pads simultaneously results in one of the pads not sounding.

→ Set the pad sensitivity level to 2. This may solve the problem if you strike one of the pads weakly.

→ Better yet, take care to strike both pads with equal force.

● Striking one pad results in other pads also sounding, even though they were not

struck.

→ Set the pad sensitivity level to 0. With this setting, pads that are not struck are effectively kept from

responding to strong hits on nearby pads.

SnS

021

NOTE

Play the Pads/Pedals

DD-65/YDD-60 Owner’s Manual

The instrument includes a click sound with adjustable tempo and time signature.

■ Setting the numerator of the time signature ...................................

The range is 0 to 16.

The ﬁrst beat is accented with a bell sound and the rest with clicks.

1 Enter the numerator value setting function.

2 Set the numerator value of the time signature.

3 Press the [FUNCTION] button to exit from the

Function mode.

Setting the Click ON/OFF

Press the [CLICK] button.

The click sounds in rhythm at the current tempo. (See “Adjusting the

Tempo” on page 25.)

To turn the click off, press the button once again.

Setting the Time Signature of the Click

Press the [FUNCTION] button once, then press the [DRUM 1] or

[DRUM 2] button a number of times until the “CL1” item appears.

After a while, the current numerator value appears next to the “CL1”

indication.

To raise the value, turn the DIAL to the right (clockwise), and to lower

it, turn the DIAL to the left (counter-clockwise).

• Default value is 4.

• When set to 00, the click sounds all beats with a click sound (no accent).

CL1

016115

NOTE

Play the Pads/Pedals

DD-65/YDD-60 Owner’s Manual

■ Setting the denominator of the time signature ...............................

Set the basic note value for each measure.

1 Enter the denominator value setting function.

2 Set the denominator value of the time signature.

3 Press the [FUNCTION] button to exit from the

Function mode.

■ Setting the click volume ....................................................................

Sets the click volume (range: 1–127).

1 Enter the click volume setting function.

2 Set the click volume by using the dial.

3 Press the [FUNCTION] button to exit from the

Function mode.

Press the [FUNCTION] button once, then press the [DRUM 1] or

[DRUM 2] button a number of times until the “CL2” item appears.

After a while, the current denominator value appears next to the

“CL2” indication.

Set the denominator value to one of the values 2 ( ), 4 ( ), 8 ( ), 16

() by using the DIAL.

• Default value is 4.

Press the [FUNCTION] button once, then press the [DRUM 1] or

[DRUM 2] button a number of times until the “CL3” item appears.

After a while current click volume will appear next to the “CL3” indi-

cation.

CL2

24816

NOTE

CL3

1 1272 126

La page charge ...

Yamaha DD-12 Le manuel du propriétaire

Marque: Yamaha

Modèle: DD-12

Catégorie: Batterie de musique

Taper: Le manuel du propriétaire

Ce manuel convient également à

DD-65
YDD-60

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha DD-12 Manuale del proprietario
English: Yamaha DD-12 Owner's manual
español: Yamaha DD-12 El manual del propietario
Deutsch: Yamaha DD-12 Bedienungsanleitung
русский: Yamaha DD-12 Инструкция по применению
Nederlands: Yamaha DD-12 de handleiding
português: Yamaha DD-12 Manual do proprietário
dansk: Yamaha DD-12 Brugervejledning
polski: Yamaha DD-12 Instrukcja obsługi
čeština: Yamaha DD-12 Návod k obsluze
svenska: Yamaha DD-12 Bruksanvisning
Türkçe: Yamaha DD-12 El kitabı
suomi: Yamaha DD-12 Omistajan opas
română: Yamaha DD-12 Manualul proprietarului

Yamaha DD-12 Le manuel du propriétaire

Ce manuel convient également à

Yamaha DD-12 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents