Dell PowerVault NX1950 Mode d'emploi

Taper
Mode d'emploi
www.dell.com | support.dell.com
Dell™ PowerVault™ NX1950
Systems
Installation Guide
安装指南
安裝指南
Guide d'installation
Installationsanleitung
設置ガイド
설치 안내서
Guía de instalación
Model EMU01
www.dell.com | support.dell.com
Dell™ PowerVault™ NX1950
Systems
Installation Guide
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you
make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to
hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property
damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2006–2007 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of
Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, PowerEdge, PowerVault, and
OpenManage are trademarks of Dell Inc.; ActiveX, Microsoft, Internet Explorer,
Windows, and Windows Server are either trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries; Broadcom is
a registered trademark and NetXtreme II is a trademark of Broadcom
Corporation; EMC, Navisphere, and PowerPath are registered trademarks of
EMC Corporation; Intel is a registered trademark of Intel Corporation; Red Hat
and Red Hat Enterprise Linux are registered trademarks of Red Hat Inc.; SUSE
is a registered trademark of Novell Inc. in the United States and other countries.
Other trademarks and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Dell Inc. disclaims
any proprietary interest in trademarks and trade names other than its own.
Model EMU01
May 2007 P/N MN424 Rev. A01
Contents 3
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 5
Solution Overview . . . . . . . . . . . . . . . . . . . . . 5
Configuring Your Hardware
. . . . . . . . . . . . . . 6
Configuring Your Software
. . . . . . . . . . . . . . 7
Windows Unified Data Storage Server 2003
. . . . . 8
2 Cabling Your Solution . . . . . . . . . . . . . . . . 11
Cabling the Integrated Solution . . . . . . . . . . . . . 11
Cabling the Dell|EMC SAN Gateway Solution
. . . . . 14
3 Connecting to the PowerVault NX1950
Storage System Initially
. . . . . . . . . . . . . 15
Configuring the IP Address . . . . . . . . . . . . . . . 16
Using the Special Administration Console
. . . . . 16
Accessing the SAC Command Prompt
. . . . . . . 17
Configuring IP Addresses and DNS
. . . . . . . . 18
Accessing the PowerVault NX1950 Storage Solution
From a Client System
. . . . . . . . . . . . . . . . . . . 19
Windows Server Remote Administration Applet
. . 19
Remote Desktop for Administration
. . . . . . . . 20
Remote Desktop Connection
. . . . . . . . . . . . 21
Remote Web Administration
. . . . . . . . . . . . 21
4 Contents
4 Completing the Configuration . . . . . . . . . 23
Dell Storage Initialization Wizard . . . . . . . . . . . . 23
Integrated Solution
. . . . . . . . . . . . . . . . . 24
Dell|EMC SAN Gateway Solution
. . . . . . . . . 24
PowerVault NX1950 Initial Configuration
Tasks Wizard
. . . . . . . . . . . . . . . . . . . . . . 25
Initial Configuration Tasks
. . . . . . . . . . . . . 26
5 Obtaining More Information . . . . . . . . . . 27
Restoring Your Operating System . . . . . . . . . . . . 27
Other Information You May Need
. . . . . . . . . . . . 27
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Introduction 5
Introduction
This document provides information about installing, cabling, configuring,
and localizing your Dell™ PowerVault™ NX1950 storage solution.
The following topics are covered in this document:
Solution overview
Cabling your solution
Connecting to the storage system
Completing the configuration
Obtaining more information
Solution Overview
The PowerVault NX1950 storage solution consists of either a single-node
or a multiple-node cluster configuration running Microsoft
®
Windows
®
Unified Data Storage Server 2003 operating system. The solution is
configured from Dell for either a PowerVault MD3000 storage array
(integrated solution) or a Dell|EMC storage array (Dell|EMC SAN gateway
solution). The solution is pre-configured with the operating system and the
required software. Minimal configuration steps are required to complete the
setup of the solution.
NOTE: The default password for your system is storageserver.
NOTE: Throughout this document PowerVault NX1950 storage system refers to
the individual storage unit and PowerVault NX1950 storage solution refers to the
configuration of the storage unit along with the storage arrays.
NOTE: The integrated solution supports two-node clustering only. The storage
area network (SAN) gateway solution supports up to eight nodes in a cluster.
Figure 1-1 illustrates the components of both the integrated solution
and the SAN gateway solution.
6 Introduction
Figure 1-1. PowerVault NX1950 Storage Solutions
Configuring Your Hardware
The PowerVault NX1950 storage solution is configured from Dell to
include the following peripherals:
PowerEdge™ Expandable RAID Controller (PERC) 5/i for internal
hardware redundant array of independent disks (RAID) 1
Serial-attached SCSI (SAS) 5/E host bus adapter (HBA) controller
to connect to the PowerVault storage sub-system for the
integrated
solution
QLE2462 Fibre Channel HBA to connect to existing or new SANs
for the
SAN
gateway solution
PowerVault NX1950 System
PowerVault NX1950 System
PowerVault MD3000 Storage Array
Dell|EMC Storage Array
Windows Unified Data
Storage Server 2003
Windows Unified Data
Storage Server 2003
Integrated Solution
Dell|EMC SAN
Gateway Solution
Introduction 7
Broadcom
®
NetXtreme II™ 5708 single-port Gigabit network interface
card (NIC) with TCP/IP Offload Engine (TOE) or Intel
®
PRO/1000
PT dual-port server adapter for additional client network connectivity
(a total number of four Gigabit Ethernet data connections are available)
Dell Remote Access Card (DRAC) 5 for remote restore capabilities
and lights-out management
For information on setting up your hardware or racks, see the following
documents on the Dell Support website at support.dell.com:
Dell PowerVault NX1950 Systems Getting Started With Your System
Dell PowerVault NX1950 Systems Hardware Owner’s Manual
Dell PowerVault MD3000 documentation
Dell|EMC storage array documentation
Configuring Your Software
Depending on the solution that you have purchased, Dell has
pre-configured the following software:
Table 1-1. List of Pre-Configured Software
Integrated Solution SAN Gateway Solution
Windows Unified Data Storage
Server 2003, x64 operating system
Windows Unified Data Storage Server
2003, x64 operating system
PowerVault MD3000 Modular
Disk Storage Manager
EMC
®
Navisphere
®
Agent and
command line interface (CLI)
PowerVault MD3000 Volume
Shadow-Copy Service (VSS)
and Virtual Disk Service (VDS)
providers
Dell|EMC VSS and VDS providers
Dell Storage Initialization Wizard Dell Storage Initialization Wizard
EMC PowerPath
®
(This version is not
licensed from Dell. For more information,
see "Registering PowerPath for the SAN
Gateway Solution" on page 24.)
EMC Storage System Initialization Wizard
Java Runtime Environment (JRE)
8 Introduction
You do not need to install the operating system as it is pre-installed.
However, you need to perform the final steps to complete the installation
and configuration of the solution. For more information, see "Completing
the Configuration" on page 23.
Windows Unified Data Storage Server 2003
The Windows Unified Data Storage Server 2003 operating system is
configured to provide the following functionality:
Optimal performance for Network File System [NFS], Common
Internet File System [CIFS], and File Service
Support for Microsoft iSCSI Software Target
to provide block storage
services in addition to file-level services
Significant enhancements in share and storage management scenarios,
as well as integration of storage server management components and
functionality
NOTE: For compatibility information, see the Dell PowerVault NX1950 Systems
Support Matrix.
Supported Editions
Dell supports the following editions of the Windows Unified Data Storage
Server 2003 operating system:
Windows Unified Data Storage Server 2003, Standard x64 Edition
Windows Unified Data Storage Server 2003, Enterprise x64 Edition
NOTE: The Windows Unified Data Storage Server 2003, Enterprise x64 Edition
operating system supports a multiple-node cluster environment.
NOTE: The Windows Unified Data Storage Server 2003, Enterprise x64 Edition
supports the x64-based versions of PowerVault NX1950 management console
snap-ins only and not the 32-bit versions.
Introduction 9
Features in This Release
Windows Unified Data Storage Server 2003 provides the following
features and functionality:
Efficient and unified file management by extending and consolidating
the management interface.
Initial Configuration Tasks user interface and CLI support through the
special administration console (SAC) simplify setting up the storage
server.
Windows Unified Data Storage Server 2003 console integrates
multiple snap-ins for file server management.
File Server Management provides support for performing additional
administration tasks.
Share and Storage Management is a new snap-in that includes two new
wizards for provisioning shares and storage.
Microsoft iSCSI Software Target including the new iSCSI Software
Target snap-in and wizards for creating and managing iSCSI targets,
virtual disks, and snapshots.
NFS provides an identity mapping interface and wizard.
Remote Desktop for Administration provides a new Microsoft Remote
Administration applet that enables browser-based remote access to the
management console from client systems running Linux or Microsoft
operating systems.
These features and functionality provide significant improvements over
previous operating systems from Microsoft.
10 Introduction
Cabling Your Solution 11
Cabling Your Solution
This section provides information about cabling the Dell™ PowerVault™
NX1950 storage system to the PowerVault MD3000 storage array or to the
Dell|EMC storage array.
Cabling the Integrated Solution
Before you turn on the system, ensure that the PowerVault MD3000 storage
array is cabled to the PowerVault NX1950 storage system(s). Figure 2-1
and Figure 2-2 illustrate how to cable the SAS 5/E HBA controllers in the
PowerVault NX1950 storage system to the PowerVault MD3000 storage
array. The PowerVault NX1950 storage solution supports single-node and
two-node cluster configurations only.
NOTE: If you turn on the PowerVault NX1950 storage system before turning on the
storage arrays, the PowerVault Storage Management Console does not detect the
PowerVault MD3000 storage array. Ensure that you turn on the storage arrays and
the storage arrays complete bootup before you turn on the PowerVault NX1950
storage system.
12 Cabling Your Solution
Figure 2-1. Single-Node Configuration
1 NIC port A to Gb Ethernet switch
(optional)
4 Port 1 on SAS HBA to In-0
on controller 1
2 NIC port B to Gb Ethernet switch
(optional)
5 Port 0 on SAS HBA to In-0
on controller 0
3 Gb1 and Gb2 to Gigabit Ethernet
switch(es)
6 DRAC port to Ethernet switch
for lights-out management
(optional)
1
2
3
45
6
PowerVault NX1950 storage system
PowerVault MD3000 storage array
controller 1
controller 0
Cabling Your Solution 13
Figure 2-2. Two-Node Configuration
NOTE: Setting up the cluster using Microsoft
®
Cluster Services (MSCS) is
supported only on the Microsoft Windows
®
Unified Data Storage Server 2003,
Enterprise Edition operating system. If you did not purchase the Enterprise
Edition, contact your sales representative to obtain an upgrade kit.
1 NIC port A to Gb Ethernet
switch (optional)
5 Port 1 on PowerVault NX1950 storage
system 1 SAS HBA to In-1 on
controller 1
2 NIC port B to Gb Ethernet
switch (optional)
6 Port 0 on PowerVault NX1950 storage
system 1 SAS HBA to In-1 on
controller 0
3 Gb1 and Gb2 to Gigabit
Ethernet switch(es)
7 Port 0 on PowerVault NX1950 storage
system 0 SAS HBA to In-0 on
controller 0
4 Port 1 on PowerVault NX1950
storage system 0 SAS HBA to
In-0 on controller 1
8 DRAC port to Ethernet switch for
lights-out management (optional)
1
2
3
4
7
8
PowerVault NX1950 storage system 0
PowerVault MD3000 storage array
6
5
PowerVault NX1950 storage system 1
controller 1
controller 0
14 Cabling Your Solution
NOTE: After performing the procedures in this document to install the
PowerVault NX1950 storage system, to successfully set up the PowerVault
NX1950 storage systems as a cluster, see the Dell PowerVault NX1950 Systems
Cluster Installation and Troubleshooting Guide on the documentation website
at www.dell.com/ostechsheets.
After cabling the solution, turn on the storage enclosure and then the
attached server(s).
Cabling the Dell|EMC SAN Gateway Solution
Ensure that your PowerVault NX1950 storage system is cabled to the
storage area network (SAN) properly and that each QLE2462 Fibre
Channel HBA port has access to the Dell|EMC storage arrays on which
you want to provision storage.
For more information, see the Dell|EMC storage array documentation.
NOTE: The procedure for cabling the PowerVault NX1950 storage system and
your SAN is similar to the procedure for cabling any server with a QLE2462
Fibre Channel HBA. Figure 2-3 illustrates an example of cabling the
PowerVault NX1950 storage solution.
The PowerVault NX1950 storage solution supports single-node and
multiple-node (up to eight nodes) cluster configurations.
Figure 2-3. SAN Gateway Solution Configuration
1 NIC port A to Gb Ethernet
switch (optional)
4 Port 2 on HBA to SAN
2 NIC port B to Gb Ethernet
switch (optional)
5 Port 1 on HBA to SAN
3 Gb1 and Gb2 to Gigabit
Ethernet switch(es)
6 DRAC port to Ethernet switch
for lights-out management
12
6
3
54
PowerVault NX1950 storage system
Connecting to the PowerVault NX1950 Storage System Initially 15
Connecting to the PowerVault
NX1950 Storage System Initially
After cabling your system, Dell™ recommends that you establish network
connectivity to access the Dell PowerVault™ NX1950 storage system using
one of the following methods:
To access and manage the system remotely through the network, you
must configure a static IP address on your PowerVault NX1950 storage
solution. After configuring your network, you can use one of the following
options to manage the system from a client system:
The remote desktop functionality
Microsoft
®
Internet Explorer
®
or Remote RDP Client Microsoft
ActiveX
®
Control
Systems running Linux can use Java Runtime Environment (JRE)
and a supported browser
For the
integrated solution
, you can manage the system locally by
connecting to the system using a keyboard, video, and mouse. If you
intend to manage your system locally, see "Completing the
Configuration" on page 23 for information about the configuring your
system.
NOTE: Dell recommends that you configure the iSCSI traffic and public network
traffic on separate networks.
16 Connecting to the PowerVault NX1950 Storage System Initially
Configuring the IP Address
For setting up the IP address on the PowerVault NX1950 storage solution,
use one of the following methods:
Dynamic Host Control Protocol (DHCP) —
If the PowerVault
NX1950 storage solution is connected to a DHCP-enabled network,
then the network address is set automatically by the DHCP server.
NOTE: Although DHCP can be used to set the initial network addresses,
Dell recommends that you configure the network connections using static
IP addresses.
Use special administration console (SAC) if you want to configure a
static IP address using a direct serial connection to the serial port of the
PowerVault NX1950 storage system. The following section provides
instructions on using SAC and setting up the IP addresses.
Using the Special Administration Console
NOTE: To use SAC, you require a female-to-female serial console cable
to connect directly from a client system to the PowerVault NX1950 storage
system’s serial port as shown in Figure 3-1.
Figure 3-1. Use the Console Cable to Connect to the SAC Prompt
NOTE: Ensure that the terminal emulation software settings on the client
system are set to 115200 baud, 8 data bits, No parity, 1 stop bit.
PowerVault NX1950
storage system
client system
female-to-female serial
console cable
Connecting to the PowerVault NX1950 Storage System Initially 17
In an environment that does not support DHCP, you can use CLI support
in SAC to connect through a serial port to a system running Microsoft
Windows
®
Unified Data Storage Server 2003 and configure network
settings. After you configure the network using SAC, you can remotely
access the graphical user interface (GUI) to configure and manage
Windows Unified Data Storage Server using the IP address. To do this,
you need to:
1
Access the SAC command prompt
2
Configure the system’s IP addresses and the Domain Name System (DNS)
Accessing the SAC Command Prompt
SAC is the primary emergency management system (EMS) CLI
environment hosted by Windows Unified Data Storage Server 2003
operating systems. It is separate from the CLI environment and provides
different functionality.
SAC is available immediately after you turn on the system. You can use
SAC to manage the server during normal system operation and to
configure most of the Windows Unified Data Storage Server 2003
operating system components. You can also use SAC when the system is in
Safe Mode and during GUI-mode setup. When EMS is enabled, the SAC
remains active as long as the kernel is running.
You can access SAC using a serial cable between the storage server and
a portable system, through a terminal emulation program such as
HyperTerminal.
NOTE: To access EMS remotely, ensure that you are using compatible client
software for terminal emulation. For more information, see "Selecting client
terminal software for Emergency Management Services" on the Microsoft
website at http://go.microsoft.com/fwlink/?LinkId=66418.
To access the SAC command prompt:
1
Start the terminal emulation program and connect to the serial port.
2
Turn on the PowerVault NX1950 storage system.
3
After EMS starts, at the SAC prompt, type
cmd
and press <Enter>
to create a command prompt window.
18 Connecting to the PowerVault NX1950 Storage System Initially
4
To switch the channel window to view the output of the command
prompt, type
ch -sn cmd0001
and press <Enter>.
5
Log on as
Administrator
.
NOTE: The default password for your system is storageserver.
For more information about using SAC, see "Using Emergency
Management Services" on the Microsoft website at
http://go.microsoft.com/fwlink/?LinkId=66415 or see Windows Unified
Data Storage Server 2003 Help.
Configuring IP Addresses and DNS
After connecting to the SAC command prompt, you can use netsh to
configure network addresses, default gateways, and DNS for a storage
server, after which you can connect remotely to the server and use the GUI
to complete other initial configuration and other management tasks.
To set the static IP address you must know the IP address, subnet mask,
and gateway address.
1
Obtain the list of available interfaces by typing the following:
netsh interface ip show interface
2
Identify the interface(s) that are displayed as
Connected
.
3
Set the IP address for the desired interface by typing the following:
netsh interface ip set address name=<interface>
source=static addr=IP address mask=
<subnet mask> gateway=<gateway address>
4
Set the DNS address by typing the following:
netsh interface ip set dns name=<interface>
source=static addr=<dns address>
NOTE: If you are using an interface name that includes spaces, place the text
in quotation marks. For example, "local area connection".
For more information about the netsh command, see "Scripting Tools" on
the Microsoft website at http://go.microsoft.com/fwlink/?LinkId=66414
or see the Windows Unified Data Storage Server 2003 Help.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258

Dell PowerVault NX1950 Mode d'emploi

Taper
Mode d'emploi