Dell PowerVault MD3620f Manuel utilisateur

Dell PowerVault

MD3600f and MD3620f

Storage Arrays

Getting Started

With Your System

Guide de mise en route

Introdução ao uso do sistema

Introducción al sistema

Dell PowerVault

MD3600f and MD3620f

Storage Arrays

Getting Started

With Your System

Regulatory Model Series E03J and E04J

Notes, Cautions, and Warnings

NOTE:

A NOTE indicates important information that helps you make better

use of your computer.

CAUTION:

A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING:

A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerVault™ are trademarks of Dell Inc.

Microsoft

®

and Windows Server

®

are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries. Red Hat

®

and Red Hat Enterprise Linux

®

are

registered trademarks of Red Hat, Inc. in the United States and other countries. SUSE

®

is a registered

trademark of Novell, Inc. in the United States and other countries. VMware

®

is a registered trademark

of VMware, Inc. in the United States and/or other jurisdictions.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model Series E03J and E04J

2011 - 08 P/N 1K67M Rev. A02

Getting Started With Your System

3

Before You Begin

NOTE:

Throughout the document, Dell PowerVault MD3600f series storage

array refers to both Dell PowerVault MD3600f and Dell PowerVault MD3620f.

Dell PowerVault MD1200 series expansion enclosure refers to both

Dell PowerVault MD1200 and Dell PowerVault MD1220.

Before setting up your PowerVault MD3600f series storage array, you must

consider certain best practices to ensure that your storage array operates at

maximum efficiency and offers full redundancy (if required).

• To enable redundancy, two Fibre Channel (FC) host bus adapters (HBA)

must be connected from the host system to the storage array. If

redundancy is not required, only one FC HBA is connected to the storage

array. See the

Support Matrix

for a list of supported HBAs and

Configuring

Fibre Channel With the Dell MD3600f Series Storage Array

for information

about installing HBA drivers. You can download both documents from

support.dell.com/manuals

.

• Before connecting any cables between the host server and storage array,

physically label each port and connector.

• Always follow proper power-up and power-down procedures when cycling

power across the network. You must also ensure that critical network

components are on separate power circuits.

Working With SFP Modules and Fiber Optic Cables

NOTE:

SFP+ modules are supported for 8 GB Fibre Channel connections.

This document refers to SFP generically.

Each storage controller can have up to four FC host ports. A small-form-factor

pluggable (SFP) module is used to connect a host port to a host or switch.

The SFP module is inserted into the port, and then a fiber optic cable is

inserted into the SFP module. The other end of the fiber optic cable is

connected to an optical interface connector either in a FC HBA on a host or

a switch. SFP modules are laser products.

WARNING:

Data processing environments can contain equipment transmitting

on system links with laser modules that operate at greater than Class 1 power

levels. Never look into the end of an optical fiber cable or open receptacle.

4

Getting Started With Your System

Guidelines for Using Fiber Optic Cables

• Do not route the cable along a folding cable management arm.

• For devices on slide rails, leave enough slack in the cables so they do not

bend to a diameter of less than 76 mm (3"), or a radius less than

38 mm (1.5"), when extended or become pinched when retracted.

• Route the cable away from places where it can be damaged by other

devices in the rack cabinet.

• Do not use plastic cable ties in place of the provided cable straps.

• Do not over-tighten the cable straps or bend the cables to a diameter of

less than 76 mm (3") or a radius less than 38 mm (1.5").

• Do not place excess weight on the cable at the connection point.

Ensure that the cable is well supported.

Guidelines for Using SFP Modules

The storage array requires SFP modules. SFP modules convert electrical

signals to optical signals that are required for FC transmission to and from

RAID controller modules. After installing the SFP modules, fiber optic cables

are used to connect the storage array to other FC devices. Before installing

SFP modules and fiber optic cables, read the following information:

• Use only Dell supported SFPs with the PowerVault MD3600f series storage

arrays. Other generic SFPs are not supported and may not work with the

storage arrays.

• The SFP module housing has an integral guide key that is designed to

prevent you from inserting the SFP module incorrectly.

• Use minimal pressure when inserting an SFP module into a FC port.

Forcing the SFP module into a port may damage the SFP module or the

port.

• You can install or remove the SFP module while the port is powered on.

• You must install the SFP module into a port before you connect the fiber

optic cable.

• You must remove the fiber optic cable from the SFP module before you

remove the SFP module from the port.

CAUTION:

When handling static-sensitive devices, take precautions to avoid

damaging the product from static electricity.

Getting Started With Your System

5

Other Documentation and Media You May Need

WARNING:

See the safety and regulatory information that shipped with

your system. Warranty information may be included within this document or

as a separate document.

NOTE:

All PowerVault MD3600f series documents are available at

support.dell.com/manuals.

• The rack documentation included with your rack solution describes how

to install your system into a rack.

• The

Owner’s Manual

provides information about system features and

describes how to troubleshoot the system and install or replace system

components.

• The

Deployment Guide

provides information about installing and

configuring the software and hardware.

• The

CLI Guide

provides information about using the command line

interface (CLI) to configure and manage your storage array.

• The

SMI-S Programmer’s Guide

provides information about using the

SMI-S provider and SMI-S programming.

• Any media that ships with your system that provides documentation and

tools for configuring and managing your system, including those

pertaining to the operating system, system management software,

system updates, and system components that you purchased

with your system.

NOTE:

Always check for updates on support.dell.com/manuals and read the

updates first because they often supersede information in other documents.

Supported Operating Systems

• Microsoft Windows Server

• Red Hat Enterprise Linux

• SUSE Linux Enterprise Server

•VMware

NOTE:

For the latest information on all the supported operating system versions,

see the Support Matrix at support.dell.com/manuals.

6

Getting Started With Your System

Common Configurations

Cabling Your Direct-Attached Hosts

Server 1

Server 2

PowerVault MD3600f

series storage array

Corporate, public, or

private network

Server 3 Server 4

Getting Started With Your System

7

Cabling Your SAN-Attached Hosts

The illustration below represents a redundant system. For example, a system

used in a remote replication environment.

PowerVault MD3600f

series storage array

Switch 2Switch 1

Up to 64 hosts

Corporate, public, or

private network

8

Getting Started With Your System

Installation and Configuration

WARNING:

Before performing the following procedure, review the safety

instructions that came with the system.

Unpacking the System

Unpack your system and identify each item with the packing list that shipped

with your system.

Installing the Rails and System in a Rack

Assemble the rails and install the system in the rack following the safety

instructions and the rack installation instructions provided with your system.

NOTE:

To balance the weight load, it is recommended that you install the

PowerVault MD3600f series storage array at the bottom of the rack and the

PowerVault MD1200 series expansion enclosures above it.

Getting Started With Your System

9

Connecting the Power Cable(s)

Ensure that the power switch is in the OFF position before connecting the

power cables. Connect the system’s power cable(s) to the system.

Securing the Power Cable(s)

Secure the cable(s) firmly to the bracket using the provided strap.

Plug the other end of the power cables into a grounded electrical outlet or

a separate power source such as an uninterrupted power supply (UPS) or

a power distribution unit (PDU). Each power supply must be connected

to a separate power circuit.

10

Getting Started With Your System

Installing and Removing SFP Modules

To install SFP modules:

1

If all the FC IN ports have an SFP module installed, go to step 5.

2

Remove the SFP module from the static protective package.

3

Remove the protective cap from the SFP module and SFP port. Store the

protective caps for future use.

4

Insert the SFP module into the host port until it clicks into place.

5

Connect an FC cable. See "Installing and Removing Fibre Channel

Cables" on page 10.

To remove SFP modules:

1

Remove the FC cable from the SFP module. See "Installing and Removing

Fibre Channel Cables" on page 10.

NOTE:

To avoid damaging the cable or the SFP module, disconnect

the FC cable before removing the SFP module.

2

Unlock the SFP module latch. For SFP modules that contain wire tabs,

unlock the SFP module latch by pulling the wire latch outward 90°.

3

With the SFP module latch in the unlocked position, remove the

SFP module. For SFP modules that contain wire tabs, grasp the wire latch

and pull the SFP module out of the port.

4

Replace the protective cap on the SFP module and the host port.

5

Place the SFP module into a static-protective package.

Installing and Removing Fibre Channel Cables

WARNING:

Data processing environments can contain equipment transmitting

on system links with laser modules that operate at greater than Class 1 power

levels. Never look into the end of an optical fiber cable or open receptacle.

Before installing an FC cable, see "Guidelines for Using Fiber Optic Cables"

on page 4.

To install an FC cable:

1

If applicable, remove the protective cap from the SFP module and store

the protective cap for future use.

2

Remove the two protective caps from one end of the cable and store them

for future use.

Getting Started With Your System

11

3

Insert the cable into an SFP module that is installed in the storage array.

The cable connector is keyed for correct installation. Holding the

connector, push in the cable until it clicks into place.

4

Remove the two protective caps from the other end of the cable and store

them future use.

5

Connect this end of the cable to one of the following devices:

– An SFP module that is installed in an FC switch port

– A FC HBA port

To remove an FC cable:

1

Press and hold the lever to release the latches before removing the cable

from the SFP module. Ensure that the levers are in the released position

when removing the cable. Do not grasp the SFP module plastic tab when

removing the cable.

2

On the end of the cable that connects into the SFP module or HBA,

press down and hold the lever to release the latches.

3

While pressing down the cable lever, pull the connector to remove the

cable from the SFP module.

4

Replace the protective caps on the cable ends.

5

Replace the protective cap on the SFP module.

12

Getting Started With Your System

Cabling Your Expansion Enclosure

Turning On the Storage Array

Turn on the components in the following order:

1

FC switches (if used)

2

MD1200 series expansion enclosures (if used)

NOTE:

Before turning on the storage array, ensure that the expansion

enclosure status LED is blue.

PowerVault MD3600f

series storage array

PowerVault MD1200

series expansion

enclosure 1 (optional)

PowerVault MD1200

series expansion

enclosure 2 (optional)

Getting Started With Your System

13

3

MD3600f series

storage array

NOTE:

Before turning on the host server(s), ensure that the storage array

status LED is blue.

4

Host server(s)

Installing the Bezel

Install the bezel (optional).

Installing HBAs and Drivers

NOTE:

Ensure that you read the Configuring Fibre Channel With the Dell MD3600f

Series Storage Array document before continuing with this procedure. For detailed

instructions about installing the MD storage software, setting up the enclosure, and

the post-installation tasks, see the Deployment Guide.

1

Physically install the HBAs.

2

Connect the cables.

3

Install the HBA drivers and the operating system HBA patches/hotfixes.

4

Ensure that the recommended HBA settings are applied.

14

Getting Started With Your System

Installing the MD Storage Software

NOTE:

For detailed instructions about installing the MD storage software, setting

up the enclosure, and the post-installation tasks, see the Deployment Guide.

The MD Storage Manager application configures, manages, and monitors the

storage array. To install the MD storage software:

1

Insert the MD series resource media.

Depending on your operating system, the installer may launch

automatically. If the installer does not launch automatically, navigate to

the root directory of the installation media (or downloaded installer

image) and run the

md_launcher.exe

file. For Linux-based systems,

navigate to the root of the resource media and run the

autorun

file.

NOTE:

By default, the Red Hat Enterprise Linux operating system mounts the

resource media with the -noexec mount option which does not allow you to

run executable files. To change this setting, see the Readme file in the root

directory of the installation media.

2

Select

Install MD Storage Software

.

3

Read and accept the license agreement.

4

Select one of the following installation options from the

Install Set

drop-down menu:

•

Full (recommended)

—Installs the MD Storage Manager (client)

software, host-based storage agent, multipath driver, and hardware

providers.

•

Host Only

—Installs the host-based storage agent and multipath

drivers.

•

Management

—Installs the management software and hardware

providers.

•

Custom

—Allows you to select specific components.

5

Select the MD storage array model(s) you are setting up to serve as data

storage for this host server.

6

Choose whether to start the event monitor service automatically when the

host server reboots or manually

NOTE:

This option is applicable only to Windows client software installation.

7

Confirm the installation location and click

Install

.

Getting Started With Your System

15

8

If prompted, reboot the host server once the installation completes.

9

Start the

MD Storage Manager

and discover the array(s).

NOTE:

If Dynamic Host Configuration Protocol (DHCP) is not used on the

network where the MD storage array’s management ports are connected, it is

recommended that you enable IPv6 on the management station to discover

the storage array(s).

10

Configure single initiator and multiple target zoning on your Fibre Channel

switches. For information about zoning, see the

Deployment Guide

.

11

If applicable, activate any premium features purchased with your storage

array. If you purchased premium features, see the printed activation card

shipped with your storage array.

NOTE:

The MD Storage Manager installer automatically installs the required

drivers, firmware, and operating system patches/hotfixes to operate your storage

array. These drivers and firmware are also available at support.dell.com. In

addition, see the Support Matrix at support.dell.com/manuals for any additional

settings and/or software required for your specific storage array.

Locating Your Service Tag

Your system is identified by a unique Express Service Code and Service Tag

number. The Express Service Code and Service Tag are found on the front

of the system and at the back of the system next to the RAID controller

modules. This information is used by Dell to route support calls to the

appropriate personnel.

16

Getting Started With Your System

NOM Information (Mexico Only)

The following information is provided on the device described

in this document in compliance with the requirements of the

official Mexican standards (NOM):

Technical Specifications

Importer:

Model number: E03J and E04J

Supply voltage: 100–240 V CA

Frequency: 50/60 Hz

Current consumption: 8.6 A

Drives

PowerVault MD3600f Up to twelve 3.5" SAS hot-swappable hard drives

(3.0 Gbps and 6.0 Gbps)

PowerVault MD3620f Up to twenty four 2.5" SAS hot-swappable

hard drives (3.0 Gbps and 6.0 Gbps)

RAID Controller Modules

RAID controller modules

• One or two hot-swappable modules with

temperature sensors

• 2 GB of cache per controller

Back-Panel Connectors (Per RAID Controller Module)

FC connectors Four FC IN ports to connect hosts

One SAS OUT port for expansion to an additional

PowerVault MD12xx enclosure

NOTE:

The SAS connector is SFF-8088 compliant.

SAS connector

Serial connector One 6-pin mini-DIN connector

NOTE:

For technical support use only.

Getting Started With Your System

17

Management Ethernet

connector

One 100/1000 Base-T port Ethernet for out-of-band

management of the enclosure

NOTE:

The default management port IP addresses for

the primary and secondary RAID controller modules

are 192.168.128.101 and 192.168.128.102, respectively.

By default, the management ports are set to DHCP.

If the controller is unable to get an IP address

configuration from a DHCP server within a specified

time out period (approximately 3 minutes), it defaults

back to static IP addressing. For more information,

see the Deployment Guide.

Expansion

PowerVault MD1200 series Supports a maximum of 192 hard drives with any

combination of PowerVault MD1200 or PowerVault

MD1220 expansion enclosures. Support for 192 hard

drives is a Premium Feature and requires activation.

The maximum number of hard drives supported

without using the Premium Feature is 120.

Redundant path connectivity provides redundant

data paths to each hard drive.

Backplane Board

Connectors

• 12 or 24 SAS hard-drive connectors

• Two power supply/cooling fan module connectors

• Two sets of RAID controller module connectors

• One control panel connector for front LEDs and

system identification button

Sensors Two temperature sensors

Back-Panel Connectors (Per RAID Controller Module) (continued)

18

Getting Started With Your System

LED Indicators

Front panel

• One two-color LED indicator for system status

• Two single-color LED indicators for power and

enclosure mode

NOTE:

The enclosure mode LED is not applicable to

the PowerVault MD3600f series storage array.

Hard-drive carrier

• One single-color activity LED

• One two-color LED status indicator per drive

Power supply/cooling fan Three LED status indicators for power supply status,

power supply/fan fault, and AC status

RAID controller module 14 single-color LEDs:

• One battery fault

• One cache active

• One controller fault

• One controller power

• One system identification

• One management Ethernet activity

• Eight FC link or fault

2 two-color LEDs:

• One SAS OUT link or fault

• One management Ethernet link speed

Switch

System identification button Located on the front control panel. This button is

used to locate a system within a rack.

Enclosure mode switch Located on the front of the system. This switch is

not applicable to the PowerVault MD3600f series

storage array.

Password reset switch Located on the back-panel of the RAID controller

module. This switch is used to reset the storage array

password.

La page charge ...

Dell PowerVault MD3620f Manuel utilisateur

Ce manuel convient également à

Dell PowerVault MD3620f Manuel utilisateur

dans d''autres langues

Documents connexes