Sony KD-75X8507G Le manuel du propriétaire

D-503-100-11(1)

SU-WL450

Wall-Mount

Bracket

Installation Information

GB

安装信息

CS

安裝資訊

CT

Thông tin Lắp đặt

VN

Informations d’installation

FR

Информация об установке

RU



TH

Informasi Pemasangan

ID

− 2 (GB) −

Installation Information for

Using Sony Wall-Mount Bracket (SU-WL450)

Supported models:

KD-85X85*G / 75X85*G / 65X85*G / 55X85*G

* In the actual model names, the “” indicates numbers and/or characters specific to each model.

To Customers

For product protection and safety reasons, Sony strongly recommends that installation of your TV

be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.

To Sony Dealers and Contractors

Provide full attention to safety during the installation, periodic maintenance and examination of this

product.

Sufficient expertise is required for installing this product, especially to determine the

strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment

of this product to the wall to Sony dealers or licensed contractors and pay adequate

attention to safety during the installation. Sony is not liable for any damage or injury

caused by mishandling or improper installation.

For Safety and proper installation, follow the Wall-mount Bracket Operation Instructions, TV Setup

Guide and the directions in this manual.

− 3 (GB) −

GB

On Safety

Thank you for purchasing this product.

To Customers

Sufficient expertise is required for

installing this product. Be sure to

subcontract the installation to Sony

dealers or licensed contractors and pay

special attention to safety during the

installation. Sony is not liable for any

damages or injury caused by

mishandling or improper installation, or

installing any other than the specified

product. Your Statutory Rights (if any) are

not affected.

To Sony dealers

Sufficient expertise is required for

installing this product. Be sure to read

this instruction manual thoroughly to do

the installation work safely. Sony is not

liable for any damages or injury caused

by mishandling or improper installation.

Please give this manual to the customer

after installation.

This instruction manual shows the correct

handling of the product and important

precautions necessary to prevent accidents.

Be sure to read this manual thoroughly and

use the product correctly. Keep this manual

available for future reference.

Products by Sony are designed with safety in

mind. If the products are used incorrectly,

however, it may result in a serious injury

through fire, electric shock, the product

toppling over, or the product dropping. Be

sure to observe the precautions for safety to

prevent such accidents.

CAUTION

Specified products

This Wall-Mount Bracket is designed for use

with the products specified TVs. For TVs,

refer to their Reference Guide to verify that

the Wall-Mount Bracket can be used.

To Customers

WARNING

If the following precautions are not

observed, serious injury or death

through fire, electric shock, or the

product dropping can result.

Be sure to subcontract

the installation to

licensed contractors and

keep small children away

during the installation.

If the Wall-Mount Bracket or the TV is not

installed correctly, the following accidents

may occur. Be sure licensed contractors carry

out installation.



The TV may fall and cause a serious injury

such as a bruise or a fracture.



If the wall on which the Wall-Mount

Bracket is installed is unstable, uneven, or

not perpendicular to the floor, the unit

may fall and cause injury or property

damage. The wall should be capable of

supporting a weight of at least four times

the TV weight.

(Refer to your TV’s Reference Guide for its

weight.)



If the installation of the Wall-Mount

Bracket on the wall is not sufficiently

sturdy, the unit may fall and cause injury or

property damage.

Be sure to subcontract

moving or dismounting

of the TV to licensed

contractors.

If persons other than licensed contractors

transport or dismount the TV, it may fall and

cause injury or property damage. Be sure

that two or more persons (three or more

persons for 75 inches and above TV set) carry

or dismount the TV.

Do not remove screws,

etc., after mounting the

TV.

If you do so, the TV may fall and cause injury

or property damage.

Do not make alterations

to the parts of the Wall-

Mount Bracket.

If you do so, the Wall-Mount Bracket may fall

and cause injury or property damage.

Do not mount any

equipment other than

the specified product.

This Wall-Mount Bracket is designed for use

with the specified product only. If you mount

equipment other than specified, it may fall or

break, and cause injury or property damage.

Do not apply any load

other than the TV on the

Wall-Mount Bracket.

Do not shake the TV left/

right, up/down.

If you do so, the TV may fall and cause injury

or property damage.

Do not lean on or hang

from the TV.

Do not lean on or hang from the TV as it may

fall on you and cause serious injury.

CAUTION

If the following precautions are not

observed, injury or property damage

may occur.

Do not handle the

product with excessive

force during cleaning or

maintenance.

Do not apply excessive force on the topside

of the TV. If you do so, the TV may fall and

cause injury or property damage.

Precautions



If you use the TV installed on the

Wall-Mount Bracket for a long time, the

wall behind or above the TV may become

discolored or the wallpaper may come

unstuck, depending on the material of the

wall.



If the Wall-Mount Bracket is removed after

installing it on the wall, the screw holes are

left.



Do not use the Wall-Mount Bracket in a

place where it is subjected to mechanical

vibrations.

Installing the Wall-

Mount Bracket

To Sony Dealers

WARNING

The following instructions are for Sony

dealers only. Be sure to read safety

precautions described above and pay

special attention to safety during the

installation, maintenance and checking

of this product.

Do not install the Wall-

Mount Bracket on wall

surfaces where the

corners or the sides of

the TV protrude away

from the wall surface.

− 4 (GB) −

Do not install the Wall-Mount Bracket on wall

surfaces such as a pillar, where the corners

or the sides of the TV protrude away from

the wall surface. If a person or object

happens to hit the protruded corner or side

of the TV, it may cause injury or property

damage.

Do not install the TV over

or under an air-

conditioner.

If the TV is exposed to water leaks or air

current from an air conditioner for a long

time, it may cause a fire, an electric shock or

a malfunction of the TV.

Be sure to install the

Wall-Mount Bracket

securely to the wall

following the instructions

in this instruction

manual.

If any of the screws are loose or fall out, the

Wall-Mount Bracket may fall and cause injury

or property damage. Be sure to use the

appropriate screws for the material of the

wall and install the unit securely using four

or more screws of 8 mm diameter (or

equivalent).

Be sure to use the

supplied screws and

attachment parts

properly following the

instructions given in

this instruction

manual. If you use

substitute items, the

TV may fall and cause

bodily injury to

someone or damage to

the TV.

Be sure to assemble the

bracket properly

following the instructed

procedure explained in

this instruction manual.

If any of the screws are loose or fall out, the

TV may fall and cause bodily injury to

someone or damage to the TV.

Be sure to tighten the

screws securely in the

designated position.

If you fail to do so, the TV may fall and cause

bodily injury to someone or damage to the

TV.

Be careful not to subject

the TV to shock during

installation.

If the TV is exposed to shock, it may fall or

break apart. This may cause injury.

Be sure to install the TV

on a wall that is both

perpendicular and flat.

If you fail to do so, the TV may fall and cause

injury.

After proper installation

of the TV, secure the

cables properly.

If people or objects get tangled with cables,

this may result in injury or damage to the TV.

Do not allow the AC

power cord (mains lead)

or the connecting cable

to be pinched.

If the AC power cord (mains lead) or the

connecting cable is pinched between the

unit and the wall or is bent or twisted by

force, the internal conductors may become

exposed and cause a short circuit or an

electrical break. This may cause a fire or an

electric shock.

The screws needed to

secure the Wall-Mount

Bracket to the wall are

not supplied.

Use the appropriate screws for the wall

material and structure when mounting the

Wall-Mount Bracket.

− 5 (GB) −

GB

Installing the TV onto the wall

Installation procedure differs, depending on

your TV.

Use the Wall-Mount Bracket SU-WL450 to

install the TV to the wall.

Note



Be sure to store the removed screws in a safe place,

keeping them away from children.

Preparing for installation



Have the TV’s Reference Guide and Setup

Guide at hand before installation.



Be sure to have a Phillips screwdriver that

fits the screws prior to the assembly.



Confirm the installing position of your TV.



Prepare four or more screws of 8 mm

diameter and one screw of 5 mm or

equivalent (not supplied). Select screws

suitable for the material of the wall.

Checking the parts

Supplied with SU-WL450



Verify that all the parts are included.

 Base (20) (1)  Pulley (2)

 PSW 6x20 (4)  PSW 4x20 with

Bush (2)

 Spacer (20) (2)  Belt (1)

 Bush (20) (M4) (2)  PSW 4x20 (2)

 Base Adaptor (2)  PSW 4x10 (8)

 Spacer (60) (2)  PSW 6x50 (2)

 Bush (M4) (2)  PSW 4x50 (2)

Table of Contents

Preparing for installation ................................. 5

Checking the parts ........................................... 5

Deciding on the installation location .............. 6

Installing the Base on the wall ........................ 8

Preparing for the installation of the TV ........... 9

KD-85/75X85G ...............................................9

KD-65/55X85G .............................................. 11

Installing the TV on the wall ........................... 13

KD-85/75X85G ..............................................13

KD-65/55X85G ..............................................15

Confirming the completion of the

installation ......................................................18

Other information ............................................... 18

Specifications ..................................................18

− 6 (GB) −

Deciding on the installation location

1 Decide on the installation location.

Make sure that the wall has enough space for the TV and is capable of supporting a weight of at

least four times that of the TV.

Refer to the following table on installing the TV to the wall. Refer to your TV’s Reference Guide

for the TV’s weight.

Screen centre point

Standard mounting Slim mounting

Unit: mm

Model Name

Display dimensions

Screen

centre

dimension

Length for mounting

Standard

mounting

Slim

mounting

KD-85X85G

1,909 1,097 251 803 142 100

KD-75X85G

1,673 963 107 595 116 75

KD-65X85G

1,450 836 99 523 115 73

KD-55X85G

1,231 713 106 468 115 73

Note



Figures in the table may differ slightly depending on the installation.



When your TV is installed on the wall, the upper side of the TV slightly leans forward.

− 7 (GB) −

GB

Allow for suitable clearance between the

TV and the ceiling and protruding parts of

the wall as shown below.

Unit: mm

300100

100 100



To ensure proper ventilation and prevent the

collection of dirt or dust:

ˋ Do not lay the TV set flat, install upside down,

backwards, or sideways.

ˋ Do not place the TV set on a shelf, rug, bed or in a

closet.

ˋ Do not cover the TV set with a cloth, such as

curtains, or items such as newspapers, etc.

ˋ Do not install the TV set as shown below.

Air circulation is blocked.

Wall

Note



If you intend to route the cables in the wall, make a

hole in the wall to insert the cables before beginning

the installation.

To prevent pinching the cables, prepare a hole in the

wall somewhere outside the perimeter of the Base

(20) , Base Adaptor  and Spacer (20) , Spacer

(60) .

2 Select Wall mounting style. It is

selectable as shown below.

2-a Standard mount

2-b Slim mount

Refer to the table of step 1.

WARNING



When 2-b is selected, rear terminal access is limited.

2-a 2-b

3 Refer to the below table about

the Base Adaptor fitting

location. In case of selecting

2-b, then skip this step.

Model Name Hook location

KD-85X85G

KD-75X85G

a

KD-65X85G

KD-55X85G

b

a

d

b

c

− 8 (GB) −

Fit Base Adaptor  by using

Screw (PSW 4x10)  to Base

(20)  when selecting 2-a.









4 Decide the positions of the

screws for installing the Base

(20) .

Refer to the specifications on page 18.

When selecting 2-a, please use the hole

positions of Base Adaptor .

WARNING



The wall that the TV will be mounted on should be

able to support a weight of at least four times that of

the TV (Refer to your TV’s Reference Guide for its

weight.).



Determine the strength of the wall the TV will be

mounted on. Reinforce the wall sufficiently, if

necessary.

Installing the Base on the

wall



Use four or more screws of 8 mm diameter

or equivalent (not supplied).



Fit four screws to the holes of Base

Adaptor  with Base (20)  (2-a only).



Install the Base (20)  on the wall

horizontally.

2-a





2-b



− 9 (GB) −

GB

Preparing for the installation

of the TV

Refer to the Setup Guide for stand installation.

KD-85/75X85ÿÿG

1 Mark the installation location on

the wall.

ˎ

Use masking tape, etc. (not supplied) to

mark the location of the TV near the

Base or Base Adaptor. Refer to the

following table.

Screen centre point

Masking tape

(1,000)

(300)

Unit: mm

Model Name

Length for

marking

Screen

centre

dimension

KD-85X85ÿÿG

1,909 683 200 251

KD-75X85ÿÿG

1,673 468 200 107

2 Remove the screws from the

rear of the TV.

3 Attach the Attachment parts for

Wall-Mount Bracket. Check the

Attachment parts by referring to

“Supplied with SU-WL450” in

“Checking the parts” on page

5.

Note

ˎ

Firmly secure the Attachment parts using screws.

ˎ

When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

ˎ

Be sure to store the used or unused parts in a safe

place for future use. Retain this manual for future

reference.

Standard mounting (2-a)

Belt ʲ

Spacer

(60 mm) ʷ

Screw (+PSW 6 x 50) ʸ

Pulley ʮ

Screw

(+PSW 6 x 20) ʯ

Slim mounting (2-b)

Note

ˎ

You cannot use some of the terminals on the rear of

the TV when using this mounting style.

Belt ʲ

Screw (+PSW 6 x 20) ʯ

Pulley ʮ

Spacer (20 mm)

ʱ

− 10 (GB) −

4 Connect the necessary cable(s)

to the TV.

Make sure to connect the cables before

installing the TV on the wall. You will be

unable to connect the cables when the TV

is installed.

Refer to the Reference Guide supplied with

your TV.

Note



Subcontract the cable routing in the wall to a licensed

contractor.



Bundle the connecting cables to prevent stepping on

them before wall mounting.

5 Detach the Table-Top Stand

from the TV.



Remove one side of the Table-Top Stand

at a time. Firmly hold the Table-Top

Stand securely with both hands while

the other people lift up the TV.

KD-85X85G

KD-75X85G



Repeat the previous step and remove

the other side of the Table-Top Stand.

Note



Three or more people are required to detach the

Table-Top Stand.



Be careful not to use excessive force while detaching

the Table-Top Stand from the TV as it may cause the

TV set to fall resulting in personal injury or physical

damage to the TV.



Take care when handling the Table-Top Stand to

prevent damage to the TV.



Be careful when lifting the TV as the Table-Top Stand

is detached, the Table-Top Stand may topple over

and cause personal injury.



Take care when removing the Table-Top Stand from

the TV to prevent it from falling over and damaging

the surface that the TV is sitting on.

− 11 (GB) −

GB

KD-65/55X85ÿÿG

1 Remove the screws from the

rear of the TV.

2 Attach the Attachment parts for

Wall-Mount Bracket. Check the

Attachment parts by referring to

“Supplied with SU-WL450” in

“Checking the parts” on page

5.

Note

ˎ

Firmly secure the Attachment parts using screws.

ˎ

When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

ˎ

Be sure to store the used or unused parts in a safe

place for future use. Retain this manual for future

reference.

Standard mounting (2-a)

Belt ʲ

Spacer

(60 mm) ʷ

Screw (+PSW 6 x 50) ʸ

Pulley ʮ

Screw

(+PSW 6 x 20) ʯ

Slim mounting (2-b)

Note

ˎ

You cannot use some of the terminals on the rear of

the TV when using this mounting style.

Belt ʲ

Screw (+PSW 6 x 20) ʯ

Pulley ʮ

Spacer (20 mm)

ʱ

3 Connect the necessary cable(s)

to the TV.

Make sure to connect the cables before

installing the TV on the wall. You will be

unable to connect the cables when the TV

is installed.

Refer to the Reference Guide supplied with

your TV.

Note

ˎ

Subcontract the cable routing in the wall to a licensed

contractor.

ˎ

Bundle the connecting cables to prevent stepping on

them before wall mounting.

− 12 (GB) −

4 Detach the Table-Top Stand

from the TV.



Remove one side of the Table-Top Stand

at a time. Firmly hold the Table-Top

Stand securely with both hands while

the other people lift up the TV.



Repeat the previous step and remove

the other side of the Table-Top Stand.

Note



Three or more people are required to detach the

Table-Top Stand.



Be careful not to use excessive force while detaching

the Table-Top Stand from the TV as it may cause the

TV set to fall resulting in personal injury or physical

damage to the TV.



Take care when handling the Table-Top Stand to

prevent damage to the TV.



Be careful when lifting the TV as the Table-Top Stand

is detached, the Table-Top Stand may topple over

and cause personal injury.



Take care when removing the Table-Top Stand from

the TV to prevent it from falling over and damaging

the surface that the TV is sitting on.

− 13 (GB) −

GB

Installing the TV on the wall

KD-85/75X85G

1 Lift the TV.



For the location of the Pulleys  to the

hang on the Base or Base Adaptor, refer

to the table of step 3 in “Deciding on the

installation location” on page 7.



Make sure that the rear of the TV

touches the Base or Base Adaptor when

holding the TV.

Note



Hold the TV securely with both hands and make sure

the Belt  and the bottom of the TV align with the

masking tape.



Carry the TV with three people and the person who is

in front of the TV leads the others to adjust the

position.



Take great care when installing the TV to the wall

especially for the person who is supporting the TV

from below, the television set may fall, causing

serious bodily injury or even death.





2 Install the TV onto the Base or

Base Adaptor.



Gently slide down the TV and hang the

Pulleys  attached to the rear of the TV

to the Base or Base Adaptor, making

sure to confirm the shape of the holes.



After installing the TV on the wall,

confirm the Pulleys  are firmly latched

into the Base or Base Adaptor.



Release both hands slowly to ensure

that the TV does not fall.



After installing the TV on the wall,

remove the masking tape, etc. from the

wall.

− 14 (GB) −

2-a







2-b







− 15 (GB) −

GB

WARNING



Be sure that two or more persons (three or more

persons for 75 inches and above TV set) hold the TV

when carrying it.

3 Preventing the bottom of the TV

from shifting.



Take up the slack of Belt  and attach it

to the wall tightly.

2-a 2-b

 



Use a 5 mm diameter screw or

equivalent (not supplied).

Note



Try to pull the bottom of the TV towards yourself

slightly, to make sure that it does not move forward.

If there is any movement, it is not fixed correctly, and

the Belt  should be secured firmly again.

KD-65/55X85G

1 Lift the TV.



For the location of the Pulleys  to the

hang on the Base or Base Adaptor, refer

to the table of step 3 in “Deciding on the

installation location” on page 7.



Make sure that the rear of the TV

touches the Base or Base Adaptor when

holding the TV.



Note



Hold the TV securely with both hands.

2 Install the TV onto the Base or

Base Adaptor.



Gently slide down the TV and hang the

Pulleys  attached to the rear of the TV

to the Base or Base Adaptor, making

sure to confirm the shape of the holes.



After installing the TV on the wall,

confirm the Pulleys  are firmly latched

into the Base or Base Adaptor.



Release both hands slowly to ensure

that the TV does not fall.

− 16 (GB) −

2-a







2-b







− 17 (GB) −

GB

WARNING



Be sure that two or more persons (three or more

persons for 75 inches and above TV set) hold the TV

when carrying it.

3 Preventing the bottom of the TV

from shifting.



Take up the slack of Belt  and attach it

to the wall tightly.

2-a 2-b

 



Use a 5 mm diameter screw or

equivalent (not supplied).

Note



Try to pull the bottom of the TV towards yourself

slightly, to make sure that it does not move forward.

If there is any movement, it is not fixed correctly, and

the Belt  should be secured firmly again.

− 18 (GB) −

Confirming the completion of

the installation

Check the following points.



The Pulleys  are firmly hung onto the Base

or Base Adaptor.



The cord and the cable are not twisted or

pinched.



The Belt  is tight with no slack.

WARNING



Improper placement of the AC power cord (mains lead),

etc. may cause fire or electric shock through a short

circuit. Be sure to confirm the completion of the

installation for safety.

Other information

When removing the TV, reverse the previous

installation procedure.

WARNING



Be sure that two or more persons (three or more persons

for 75 inches and above TV set) hold the TV when

removing it.

Specifications

f

c

d

b

a

g

e

h2h1

Dimensions: (Approx.) [mm]

a : 400

b : 300

c : 200

d : 100

e : 80

f : 480

g : 100

h1 : 20 (case 2-b)

h2 : 60 (case 2-a)

Weight (base only): (Approx.) [kg]

0.8

Design and specifications are subject to change without

notice.

− 2 (CS) −

使用 Sony 挂壁式支架 (SU-WL450) 的安装信息

支持型号:

KD-85X85

*

G / 75X85

*

G / 65X85

*

G / 55X85

*

G

* 在实际机型名称中，“”指的是特定于每个型号的数字和/或字符。

致用户

为保护产品和安全理由，Sony 坚持建议安装您的电视的任务由 Sony 经销商或授权承包商进行。请勿尝

试自行安装。

致 Sony 经销商和承包商

安装、定期维修和检查此产品时，请务必注意安全。

安装本产品需要足够的专业技能, 尤其是确定用于承受电视机重量的墙壁的强度。务必将本产品的墙

上安装托付于 Sony 经销商或授权承包商并在安装时特别注意安全。对于处置不当或安装不妥造成的

损害或人身伤害，Sony 将不负责任。

为了确保安全和正确安装，请遵循挂壁式支架使用说明书、电视机设定指南以及本手册中的说明。

− 3 (CS) −

CS

安全事项

感谢您购买本产品。

致用户

安装本产品要求具有一定的技术。确保将

安装工作委托给 Sony 经销商或经许可的

承包商，并在安装过程中特别注意安

全。Sony 对操作不当或安装不正确，或安

装任何非指定产品而引起的任何损坏或伤

害概不负责。您的法定权利（如果有的

话）不受影响。

致 Sony 经销商

安装本产品要求具有一定的技术。为安全

地进行安装工作，请务必仔细通读本说明

书。Sony 对操作不当或安装不正确而引起

的任何损坏或伤害均不负责。请在完成安

装后将本说明书交给用户。

本说明书介绍了正确使用本产品的信息，以及

为防止事故发生需注意的重要事项。请务必仔

细通读本说明书并正确使用本产品。保存好本

说明书以备将来参考。

Sony 的产品设计非常注重安全。然而，如果不

正确使用这些产品，则可能因火灾、电击、产

品倾倒或产品跌落而导致人员严重受伤。请务

必遵守安全注意事项以防止此类事故发生。

注意

指定产品

本挂壁式支架设计用于指定产品的电视机。请

参阅电视机的参考指南，确定本挂壁式支架是

否可用于该电视机。

致用户

警告

如果不遵守下列注意事项，则因火灾、电击

或产品跌落而导致人员严重受伤或死亡。

请务必将安装工作委托给经

许可的承包商，并确保在安

装过程中无儿童接近。

如果挂壁式支架或电视机安装不正确，则可能

发生下列事故。请确保安装工作由经许可的承

包商进行。



电视机可能跌落并造成人员严重受伤，如擦

伤或骨折等。



如果安装挂壁式支架的墙体不平稳、不平整

或与地面不垂直，则装置可能会跌落，从而

造成人员受伤或财产损失。墙体能承受的重

量应该至少是电视机重量的四倍。

（请参阅您电视机的参考指南，了解其重

量。）



如果墙壁上安装的挂壁式支架不够牢固，则

装置可能会跌落并造成人员受伤或财产损

失。

请务必将电视机的搬移或拆

卸工作委托给经许可的承包

商进行。

如果由经许可的承包商之外的其他人员进行电

视机的搬运或拆卸工作，则电视机可能跌落并

造成人员受伤或财产损失。请确保由两个或两

个以上（75 英寸及以上机型需要三个或三个以

上）的人员搬运或拆卸本电视机。

电视机安装完之后，请勿拆

下螺丝等零件。

否则，电视机可能会跌落并造成人员受伤或财

产损失。

请勿改装挂壁式支架的零部

件。

否则，挂壁式支架可能会跌落并造成人员受伤

或财产损失。

请勿将指定产品之外的其他

设备安装到支架上。

本挂壁式支架系为指定产品专门设计。如果您

安装非指定设备，则支架可能跌落或破裂，并

造成人员受伤或财产损失。

除电视机之外，请勿在挂壁

式支架上再加挂其他重物。

请勿左右或上下摇晃电视

机。

否则，电视机可能会跌落并造成人员受伤或财

产损失。

请勿倚靠或吊挂在电视机

上。

请勿倚靠或吊挂在电视机上，因为电视机可能

跌落到您身上，并造成人员严重受伤。

注意

如果不遵守下列注意事项，则可能导致人

员受伤或财产损失。

在清洁或维护过程中，请勿

对产品施加过大的力量。

请勿在电视机的顶部施加过大的力量。否则，

电视机可能会跌落并造成人员受伤或财产损

失。

注意事项



如果长期使用安装于挂壁式支架的电视机，

则视墙面材料而定，电视机后面或上面的墙

面可能会褪色，或出现墙纸脱落。



如果在墙壁上安装挂壁式支架后再将其拆

下，则墙壁上会留下螺丝孔。



请勿在容易受到机械振动的地方使用挂壁式

支架。

安装挂壁式支架

致 Sony 经销商

警告

下列说明仅适用于 Sony 经销商。请务必

阅读上述安全注意事项，并在安装、维护

和检查本产品时特别注意安全。

请勿将挂壁式支架装在会使

电视机的边角或侧面突出于

墙面的墙壁位置。

请勿将挂壁式支架装在柱子等会使电视机的边

角或侧面突出于墙面的墙壁位置。如果有人或

物体正巧撞到电视机的边角或侧面，则会引起

人员受伤或财产损失。

请勿将电视机安装在空调的

上面或下方。

如果电视机长期接触空调的漏水，或长期暴露

于空调的气流中，则可能造成火灾、电击或电

视机故障。

请务必按照本说明书中的指

示牢固地将挂壁式支架安装

在墙上。

如果有螺丝松动或掉落，则挂壁式支架会跌落

并造成人员受伤或财产损失。请务必使用适合

墙壁材料的螺丝牢固安装本装置。固定时请使

用四个或更多个 8 mm 直径（或相当规格）的

螺丝。

请务必按照本说明书中给

出的指示正确使用提供的

螺丝和附件。如果使用其

他替代零件，则电视机可

能会跌落，并造成人身伤

害或电视机损坏。

请务必按照本说明书中介绍

的步骤正确安装支架。

如果有螺丝松动或掉落，则电视机可能会跌

落，并造成人身伤害或电视机损坏。

La page charge ...

Sony KD-75X8507G Le manuel du propriétaire

Ce manuel convient également à

Sony KD-75X8507G Le manuel du propriétaire

dans d''autres langues

Documents connexes