Wacker Neuson CRT48-35L Manuel utilisateur

5000184411 06 0911

Operator’s Manual

Ride-On Trowel

CRT 48

Notice d’Emploi

Truelles à conducteur porté

5000184411

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000184387 06 0911

CRT48 Foreword

wc_tx001539gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 If you are missing either of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Machine Item Number

CRT 48-35V 0620112, 0620807

CRT 48-34V 0620075, 0620805

CRT 48-35L 0620113, 0620806

CRT 48-31V 0620476

Foreword CRT48

4 wc_tx001539gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Original Declaration of Conformity

2011-CE-CRT36-CRT48-en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin USA

Product

Product category

Product function

Item number

CRT 36-24A, CRT 36-25, CRT 48-35V, CRT 48-34V,

CRT 48-35L

Trowel

To smooth and finish semi-cured concrete

0620801, 0620802, 0620803, 0620804, 0620805,

0620806, 0620807

Guidelines and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following guidelines and standards:

2006/42/EC, 2006/95/EC, 2004/108/EC, EN12649

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson SE, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 15.08.2011

William Lahner

Vice President of Engineering

Scott V. Grahl

Manager, Product Engineering

wc_bo5000184387_06TOC.fm 7

Table of ContentsCRT 48

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 11

1.1 Signal Words Used in this Manual ..................................................... 11

1.2 Machine Description and Intended Use ............................................. 11

1.3 Safety Guidelines for Operating the Machine ..................................... 13

1.4 Operator Safety while Using Internal Combustion Engines ............... 14

1.5 Service Safety .................................................................................... 16

1.6 Transport Safety ................................................................................. 17

2 Labels 18

2.1 Label Locations .................................................................................. 18

2.2 Label Meanings .................................................................................. 20

3 Lifting and Transporting 26

4 Operation 27

4.1 Preparing the Machine for First Use ................................................... 27

4.2 Position of the Operator ..................................................................... 27

4.3 Recommended Fuel ........................................................................... 28

4.4 Recommended Fuel (Kohler) ............................................................. 28

4.5 Refueling the Machine ........................................................................ 29

4.6 Features and Controls ........................................................................ 30

4.7 New Machines .................................................................................... 32

4.8 Before Starting ................................................................................... 32

4.9 Vanguard—Starting ............................................................................ 33

4.10 Kohler—Starting ................................................................................. 33

4.11 Stopping ............................................................................................. 33

4.12 Operation ............................................................................................ 34

4.13 Steering .............................................................................................. 35

4.14 Pitch Adjustment ................................................................................ 36

4.15 Emergency Shutdown Procedure ....................................................... 36

8 wc_bo5000184387_06TOC.fm

Table of Contents CRT 48

5 Maintenance 37

5.1 Maintaining the Emission Control System ...........................................37

5.2 Periodic Maintenance Schedule ..........................................................38

5.3 Trowel Gearboxes ...............................................................................39

5.4 Control Linkage Lubrication .................................................................40

5.5 Control Arm Adjustment (Forward or Backward) .................................41

5.6 Steering Assist System .......................................................................42

5.7 Right-hand Control Arm Adjustment (Right or Left) .............................42

5.8 Blade Arm Adjustment .........................................................................43

5.9 Mounting Float Pans ...........................................................................44

5.10 Drive Belt .............................................................................................45

5.11 Battery Jump Start Procedure .............................................................46

5.12 Vanguard—Spark Plug ........................................................................47

5.13 Servicing the Air Cleaner .....................................................................47

5.14 Vanguard—Engine Oil and Filter .........................................................48

5.15 Kohler—Engine Oil and Filter ..............................................................50

6 Troubleshooting 52

7 Technical Data 54

7.1 Engine .................................................................................................54

7.2 Sound and Vibration Specifications .....................................................56

8 AEM Safety Manual 57

9 Emission Control Systems Information and Warranty 73

9.1 Emission Control System Background Information .............................73

9.2 Limited Defect Warranty for Exhaust Emission Control System .........74

9.3 Limited Defect Warranty for Wacker Neuson Evaporative

Emission Control Systems ..................................................................75

wc_bo5000184387_06TOC.fm 9

Table of ContentsCRT 48

10 Schematics 78

10.1 CRT 48-35V—Electrical Schematic ................................................... 78

10.2 CRT 48-35V—Electrical Schematic Components .............................. 79

10.3 CRT 48-35L—Electrical Schematic .................................................... 80

10.4 CRT 48-35L—Electrical Schematic Components .............................. 81

10.5 CRT 48-34V and CRT 48-31V—Electrical Schematic ........................ 82

10.6 CRT 48-34V and CRT 48-31V—Electrical Schematic Components .. 83

10 wc_bo5000184387_06TOC.fm

Table of Contents CRT 48

CRT 48 Safety Information

wc_si000188gb.fm 11

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

1.2 Machine Description and Intended Use

This machine is a ride-on concrete finishing trowel. The Wacker Neuson

Ride-On Trowel consists of a frame onto which are mounted a gasoline or

diesel engine, a fuel tank, a water tank, two gearboxes joined by a drive

shaft, and an operator’s platform with controls and a seat. A set of metal

blades is connected to each gearbox. A ring guard surrounds the blades.

The engine rotates the blades via the gearboxes and a clutch

mechanism. The rotating blades ride on the surface of curing concrete,

creating a smooth finish. The operator, who sits on the operator’s

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information CRT 48

12 wc_si000188gb.fm

platform, uses the controls and the throttle pedal to control speed and

direction of the machine.

This machine is intended to be used for floating and burnishing curing

concrete.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or other

persons in the area. Machine damage caused by misuse is not covered

under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to finish inappropriate materials such as slurries,

sealers, or epoxy finishes

• Operating the machine outside of factory specifications

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest

global safety standards. It has been carefully engineered to eliminate

hazards as far as practicable and to increase operator safety through

protective guards and labeling. However, some risks may remain even

after protective measures have been taken. They are called residual

risks. On this machine, they may include exposure to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Chemical burns from the curing concrete

• Fire hazards from improper refueling techniques

• Fuel and its fumes, fuel spillage from improper lifting technique

• Personal injury from improper lifting techniques

• Cutting hazards from sharp or worn blades

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

CRT 48 Safety Information

wc_si000188gb.fm 13

1.3 Safety Guidelines for Operating the Machine

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

•children

• people impaired by alcohol or drugs

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

1.3.1 Never operate this machine in applications for which it is not intended.

1.3.2 Do not allow anyone to operate this equipment without proper training.

People operating this equipment must be familiar with the risks and

hazards associated with it.

1.3.3 Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and may

cause burns.

1.3.4 Do not use accessories or attachments that are not recommended by

Wacker Neuson. Damage to equipment and injury to the user may

result.

1.3.5 NEVER operate the machine with the beltguard missing. Exposed

drive belt and pulleys create potentially dangerous hazards that can

cause serious injuries.

1.3.6 Never leave the machine running unattended.

WARNING

Safety Information CRT 48

14 wc_si000188gb.fm

1.3.7 Do not run the machine indoors or in an enclosed area such as a deep

trench unless adequate ventilation, through such items as exhaust

fans or hoses, is provided. Engine exhaust contains carbon monoxide.

This is a poison you cannot see or smell. Exposure to carbon

monoxide can cause loss of consciousness and CAN KILL YOU IN

MINUTES.

1.3.8 ALWAYS remain aware of moving parts and keep hands, feet, and

loose clothing away from the moving parts of the machine.

1.3.9 Always wear protective clothing appropriate to the job site when

operating the machine.

1.3.10 Read, understand, and follow procedures in the Operator’s Manual

before attempting to operate the machine.

1.3.11 Be sure operator is familiar with proper safety precautions and

operation techniques before using machine.

1.3.12 Close fuel valve on engines equipped with one when machine is not

being operated.

1.3.13 Store the machine properly when it is not being used. The machine

should be stored in a clean, dry location out of the reach of children.

1.3.14 Always operate the machine with all safety devices and guards in

place and in working order.

1.3.15 Do not use a cellphone or send text messages while operating this

machine.

1.4 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

CRT 48 Safety Information

wc_si000188gb.fm 15

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

• Do not refuel if the machine is positioned in a truck fitted with a

plastic bed liner. Static electricity can ignite the fuel or fuel vapors.

Safety Information CRT 48

16 wc_si000188gb.fm

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

1.5.1 Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

1.5.2 Do not crank a flooded engine with the spark plug removed on

gasoline-powered engines. Fuel trapped in the cylinder will squirt out

the spark plug opening.

1.5.3 Do not test for spark on gasoline-powered engines if the engine is

flooded or the smell of gasoline is present. A stray spark could ignite

the fumes.

1.5.4 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

1.5.5 ALWAYS turn engine off and remove key from machine before

performing maintenance or making repairs.

1.5.6 ALWAYS handle blades carefully. The blades can develop sharp

edges which can cause serious cuts.

1.5.7 Keep the area around the muffler free of debris such as leaves, paper,

cartons, etc. A hot muffler could ignite the debris and start a fire.

1.5.8 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

1.5.9 Disconnect the spark plug on machines equipped with gasoline

engines, before servicing, to avoid accidental start-up.

1.5.10 ALWAYS switch off the power supply at the battery disconnect before

adjusting or maintaining the electrical equipment.

WARNING

CRT 48 Safety Information

wc_si000188gb.fm 17

1.5.11 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

1.6 Transport Safety

1.6.1 Always engage the steering handle lock before lifting the machine.

DO NOT lift the trowel by the guard rings or any part of the trowel other

than the lifting fixture, as the component may fail, causing the trowel to

fall, possibly injuring bystanders.

WARNING

Labels CRT 48

18 wc_si000513gb.fm

2 Labels

2.1 Label Locations

L

Q

I

M

BB

Z

Q

L

CC

R

S

T

D

E

U

C

F

N

wc_gr003770

CRT 48 Labels

wc_si000513gb.fm 19

wc_gr003771

J

M

V

O

G

AA

DD

K

BB

M

W

H

W

H

A/B

Labels CRT 48

20 wc_si000513gb.fm

2.2 Label Meanings

Wacker Neuson machines use international pictorial labels where

needed. These labels are described below.

A

DANGER!

Asphyxiation hazard.

Engines emit carbon monoxide.

Do not run the machine indoors or in an enclosed area

unless adequate ventilation, through such items as

exhaust fans or hoses, is provided.

Read the Operator’s Manual. No sparks, flames, or

burning objects near the machine. Stop the engine

before refueling.

B

DANGER!

Asphyxiation hazard.

Engines emit carbon monoxide.

Do not run the machine indoors or in an enclosed area

unless adequate ventilation, through such items as

exhaust fans or hoses, is provided.

Read the Operator’s Manual. No sparks, flames, or

burning objects near the machine. Stop the engine

before refueling.

C

Water tank fill. Use only clean water or water-based

retardants.

D

WARNING!

Always wear hearing and eye protection when operating

this machine.

STOP

0178751

La page charge ...

Wacker Neuson CRT48-35L Manuel utilisateur

Ce manuel convient également à

Wacker Neuson CRT48-35L Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents