Yamaha RX-V1900 Le manuel du propriétaire

Printed in Malaysia WP38640

RX-V1900

AV Receiver

Ampli-tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

RX-V1900_G-cv.fm Page 1 Friday, July 18, 2008 6:07 PM

Black process 45.0° 240.0 LPI

Caution-i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press

A

MASTER ON/OFF to

release it outward to the OFF position to turn off this unit, the

main room, Zone 2 and Zone 3 and then disconnect the AC

power plug from the AC wall outlet.

19

VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

................................AC 110/120/220/230–240 V, 50/60 Hz

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by

A

MASTER ON/OFF. In

this state, this unit is designed to consume a very small

quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

Caution: Read this before operating your unit.

Caution-ii En

Limited Guarantee for European Economic Area (EEA) and Switzerland

Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from

whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our

website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).

The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha

undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge

for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been

discontinued or is considered uneconomic to repair.

Conditions

1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a

statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the

product may be returned at the customer’s expense.

2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.

3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.

4. The following are excluded from this guarantee:

a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.

b. Damage resulting from:

(1) Repairs performed by the customer himself or by an unauthorised third party.

(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to

ensure the product is adequately packaged when returning the product for repair.

(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper

use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in

the country where it is used.

(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.

(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.

(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety

standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.

(7) Non AV (Audio Visual) related products.

(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or

http://www.yamaha-uk.com/ for U.K. resident.)

5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.

6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the

product.

7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.

8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising

from their sales/purchase contract.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical

and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points, in accordance with your national legislation and the Directives 2002/96/

EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and

prevent any potential negative effects on human health and the environment which could otherwise

arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your

local municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact

your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

Caution: Read this before operating your unit.

Caution-iii En

Note on source code distribution

This product includes software code subject to the GNU General

Public License (GPL) or the GNU Lesser General Public License

(LGPL). The copy, distribution, or change of this software code is

licensed under the terms of the GPL or the LGPL. The source

code is available at the following website:

http://www.global.yamaha.com/download/

The source code is also available on a physical media (such as a

CD-ROM) at actual cost.

Contact: AV products division, Yamaha Corporation,

10-1 Nakazawa-cho, Naka-ku, Hamamatsu 430-8650,

Japan

In principle, the source code is offered for 3 years from the day of

purchase.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535

& other U.S. and worldwide patents issued & pending. DTS is a

registered trademark and the DTS logos, Symbol, DTS-HD and

“iPod” is a trademark of Apple Inc., registered in the U.S. and

other countries.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks, or registered trademarks of HDMI

Licensing LLC.

x.v.Color™

“x.v.Color” is a trademark of Sony Corporation.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the

buttons on the front panel or the ones on the remote

control. In case the button names differ between the front

panel and the remote control, the button name on the

remote control is given in parentheses.

• This manual is printed prior to production. Design and

specifications are subject to change in part as a result of

improvements, etc. In case of differences between the

manual and product, the product has priority.

•“

A

MASTER ON/OFF” or “

3

DVD” (example)

indicates the name of the parts on the front panel or the

remote control. Refer to the attached sheet or the pages at

the end of this manual for the information about each

position of the parts.

iPod

TM

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

English

Features ................................................................... 3

Supplied accessories .................................................. 3

Getting started ........................................................ 4

Quick start guide .................................................... 5

Connections............................................................. 9

Optimizing the speaker setting for your

listening room.................................................... 29

Before starting the automatic setup ......................... 29

Basic automatic setup .............................................. 29

Advanced automatic setup....................................... 32

Reloading the automatic setup parameters .............. 33

Playback ................................................................ 34

Basic procedure ....................................................... 34

Selecting audio input jacks (AUDIO SELECT)...... 35

Selecting the multi-channel input component ......... 35

Using your headphones............................................ 35

Muting the audio output........................................... 36

Displaying the input source information

(SIGNAL INFO) ................................................. 36

Using the sleep timer ............................................... 37

Sound field programs ........................................... 38

Selecting sound field programs ............................... 38

Using CINEMA DSP 3D mode............................... 44

Enjoying unprocessed input sources........................ 44

Using audio features ............................................. 45

Enjoying pure hi-fi sound ........................................ 45

Adjusting the tonal quality....................................... 45

Adjusting the speaker level...................................... 45

FM/AM tuning ...................................................... 46

Overview.................................................................. 46

FM/AM tuning operations ....................................... 46

Preset FM/AM stations ............................................ 47

Radio Data System tuning

(Europe and Russia models only).................... 49

Selecting the Radio Data System program type

(PTY SEEK mode).............................................. 49

Using the enhanced other networks (EON) data

service.................................................................. 50

Displaying the Radio Data System information ...... 50

Using iPod™.......................................................... 52

Controlling iPod™................................................... 52

Using Bluetooth™ components ........................... 54

Pairing the Bluetooth™ receiver and your Bluetooth

component ........................................................... 54

Playback of the Bluetooth™ component................. 54

Using USB features............................................... 55

Using shortcut buttons ............................................. 56

Advanced sound configurations...........................58

Selecting decoders ................................................... 58

Changing sound field parameter settings................. 59

Customizing this unit (MANUAL SETUP).........66

Operating the MANUAL SETUP menu.................. 66

1 SPEAKER MENU................................................ 67

2 VOLUME MENU ................................................ 69

3 SOUND MENU.................................................... 70

4 VIDEO MENU ..................................................... 72

5 INPUT MENU...................................................... 73

6 OPTION MENU................................................... 75

Saving and recalling the system settings

(SYSTEM MEMORY)......................................78

Saving the system settings....................................... 78

Loading the system settings..................................... 79

Using examples........................................................ 80

Remote control features........................................81

Controlling this unit, a TV, or other components.... 81

Setting remote control codes ................................... 83

Programming codes from other remote controls ..... 85

Changing source names in the display window....... 86

Macro programming features .................................. 87

Clearing configurations ........................................... 89

Using multi-zone configuration............................90

Connecting the Zone 2 and Zone 3 components ..... 90

Controlling Zone 2 or Zone 3 .................................. 91

Advanced setup......................................................93

Using the advanced setup menu .............................. 93

Troubleshooting.....................................................95

Resetting the system............................................105

Glossary................................................................106

Sound field program information......................110

Parametric equalizer information .....................111

Specifications .......................................................112

SET MENU tree ..................................................114

Index.....................................................................116

(at the end of this manual)

Front panel................................................................i

Remote control ....................................................... ii

Sound output in each sound field program......... iii

GPL/LGPL...............................................................v

List of remote control codes ..................................ix

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

APPENDIX

“

A

MASTER ON/OFF” or “

3

DVD” (example) indicates

the name of the parts on the front panel or the remote control.

Refer to the attached sheet or the pages at the end of this

manual for the information about each position of the parts.

2 En

By configuring the parameters in “MANUAL SETUP”, you can adjust a variety of system settings suited for your

listening environment. The following is a brief description of some of the useful menus you can configure in “MANUAL

SETUP”. For more detailed information, see “Customizing this unit (MANUAL SETUP)” (page 66) and “SET MENU

tree” (page 114).

Fine adjusting the speaker settings

In case speaker settings configured by automatic setup

does not match your listening environment, you can

configure them manually.

SPEAKER MENU → CONFIG (page 67)

SPEAKER MENU → LEVEL (page 68)

SPEAKER MENU → DISTANCE (page 68)

Specifying the muting type

In case you do not want to fully mute audio when you

receive a call while watching your favorite TV program,

you can use this menu to specify the muting level.

VOLUME MENU → MUTING TYPE (page 70)

Specifying the initial volume level

By adjusting this parameter, you can automatically control

the initial volume level regardless of the recording level of

the audio source.

VOLUME MENU → INIT. VOL. (page 70)

Adjusting the dynamic range

The dynamic range is the difference between the

minimum and maximum amplitude. The higher the

dynamic range, the more accurate the sound reproduction

for bitstream signals. You can adjust the dynamic range

for speakers and headphones individually.

SOUND MENU → DYNAMIC RANGE (page 71)

Adjusting the audio and video synchronization

Sometimes, depending on your video source component,

video is delayed relative to audio due to processing

problems. In this case, you need to manually adjust the

audio delay to keep it synchronized with the video. If you

connect the video source component to this unit using an

HDMI connection and your component supports the

LIPSYNC feature, you can adjust the audio/video

synchronization automatically.

SOUND MENU → LIPSYNC (page 71)

Changing input/output assignment

In case the initial input/output assignments do not

correspond to your needs, you can rearrange them

according to your component to be connected to this unit.

You can also edit the input name to be displayed in the

front panel or in the OSD as necessary.

INPUT MENU → (input source) →

I/O ASSIGNMENT

(page 74)

INPUT MENU → (input source) → INPUT RENAME

(page 74)

Fixing the volume difference between input

sources

The sound output level may vary depending on the audio

source components connected to this unit. In this case, you

can reduce or increase the output level of each input

source using this feature.

INPUT MENU → (input source) → VOL. TRIM

(page 74)

Setting the background video for audio sources

If you want to enjoy video images in combination with

music playback or radio, configure this setting to specify

the video input source. For example, to view DVD video

images while listening to the FM radio, set this setting

under “TUNER” to “DVD”.

INPUT MENU → (input source) → BGV (page 74)

Adjusting the brightness of the front panel

display

You can make the front panel display darker or brighter by

configuring this setting.

OPTION MENU → DISPLAY SET → DIMMER

(page 75)

Turning on or off the short message display

Each time you operate this unit using controls on the front

panel or remote control keys, this unit displays short

messages on the OSD. If you want to turn off the short

message display, select “OFF” in this setting (Initial

factory setting is “ON”).

OPTION MENU → DISPLAY SET → SHORT

MESSAGE (page 76)

Setting the amount of time to display OSD

information

You can set the amount of time to display iPod menu or

USB menu in the OSD after you perform a certain

operation.

OPTION MENU → DISPLAY SET → ON SCREEN

(page 76)

Protecting the setup values

After you have configured the sound field program

parameters and other system settings, you can use this

feature to prevent accidental changes to those setup

values.

OPTION MENU

→ MEMORY GUARD (page 76)

What you can do with MANUAL SETUP

FEATURES

3 En

INTRODUCTION

English

Built-in 7-channel power amplifier

◆ Minimum RMS output power

(20 Hz to 20 kHz, 0.04% THD, 8 Ω)

Front: 130 W + 130 W

Center: 130 W

Surround: 130 W + 130 W

Surround back: 130 W + 130 W

Various input/output connectors

◆ HDMI (IN x 4, OUT x 1), Component video (IN x 3, OUT x

1), S-video (IN x 6, OUT x 3), Composite video (IN x 6, OUT

x 3), Coaxial digital audio (IN x 3), Optical digital audio (IN x

5, OUT x 2), Analog audio (IN x 10, OUT x 3)

◆ Speaker out (7-channel), Pre out (7-channel), Subwoofer out,

Presence out, Zone 2/Zone 3 out

◆ Discrete multi-channel input (6 or 8-channel)

Sound field programs

◆ Proprietary Yamaha technology for the creation of sound

fields

◆ CINEMA DSP 3D

◆ Compressed Music Enhancer mode

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

Digital audio decoders

◆ Dolby TrueHD, Dolby Digital Plus decoder

◆ DTS-HD Master Audio, DTS-HD High Resolution Audio

decoder

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS 96/24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx

decoder

◆ DTS NEO:6 decoder

Sophisticated FM/AM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

◆ Radio Data System capability (Europe model only)

HDMI™ (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or

high-definition video as well as multi-channel digital audio

based on HDMI version 1.3a (HDMI is licensed by HDMI

Licensing, LLC.)

– Automatic audio and video synchronization (lip sync)

information capability

– Deep Color video signal (30/36 bit) transmission capability

– “x.v.Color” video signal transmission capability

– High refresh rate and high resolution video signals

capability

– High definition digital audio format signals capability

◆ HDCP (High-bandwidth Digital Content Protection System)

licensed by Digital Content Protection, LLC.

◆ Analog video to HDMI digital video up-conversion

(composite video ↔ S-video ↔ component video → HDMI

digital video) capability for monitor out

◆ Analog video up-scaling from 480i (NTSC)/576i (PAL) or

480p/576p to 720p, 1080i or 1080p

DOCK terminal

◆ DOCK terminal to connect a Yamaha iPod universal dock

(such as YDS-11, sold separately) or Bluetooth wireless audio

receiver (such as YBA-10, sold separately)

USB features

◆ USB port to connect a USB memory device or a USB portable

audio player

Automatic speaker setup features

◆ Advanced YPAO (Yamaha Parametric room Acoustic

Optimizer) for automatic speaker setup

◆ Multi-point measurement feature for multiple listening

positions

◆ Parametric equalizer select feature

Other features

◆ 192-kHz/24-bit D/A converter

◆ OSD (on-screen display) menus that allow you to optimize

this unit to suit your individual audiovisual system

◆ Analog video interlace/progressive conversion from

480i (NTSC)/576i (PAL) to 480p/576p

◆ Pure Direct mode for pure hi-fi sound for all sources

◆ Adaptive dynamic range controlling capability

◆ Adaptive DSP effect level controlling capability

◆ Remote control with preset remote control codes, learning and

macro capability

◆ ZONE 2/ZONE 3 custom installation facility

◆ Zone switching capability between the main zone and

ZONE 2/ZONE 3 using ZONE CONTROLS

◆ SYSTEM MEMORY capability for saving and recalling

multiple system parameter settings

◆ Sleep timer for each zone

Check that you received all of the following parts.

❏ Remote control

❏ Batteries (4) (AAA, R03, UM-4)

❏ Power cable (Two for Asia model)

❏ Optimizer microphone

❏ AM loop antenna

❏ Indoor FM antenna

❏ Speaker terminal wrench

Features

Supplied accessories

GETTING STARTED

4 En

■ Installing batteries in the remote control

1 Take off the battery compartment cover.

2 Insert the four supplied batteries

(AAA, R03, UM-4) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

3 Snap the battery compartment cover back

into place.

• Change all of the batteries if you notice the following

conditions:

– the operation range of the remote control decreases.

– the transmit indicator does not flash or its light becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote control,

the contents of the memory may be cleared. When the memory

is cleared, insert new batteries, set up the remote control code

and program any acquired functions that may have been

cleared.

■ VOLTAGE SELECTOR

(Asia and General models only)

Getting started

Notes

1

3

2

Caution

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local voltage BEFORE

plugging the power cable into the AC wall outlet.

Improper setting of the VOLTAGE SELECTOR may

cause damage to this unit and create a potential fire

hazard.

Rotate the VOLTAGE SELECTOR clockwise or

counterclockwise to the correct position using a straight

slot screwdriver.

Voltages are as follows:

........................AC 110/120/220/230–240 V, 50/60 Hz

230-

240V

VOLTAGE

SELECTOR

Voltage indication

QUICK START GUIDE

5 En

INTRODUCTION

English

The following steps describe the easiest way to enjoy DVD movie playback in your home theater.

In these steps, you need the following supplied

accessories.

❏ Power cable

The following items are not included in the package of this

unit.

❏ Speakers

❏ Front speaker ......................................x 2

❏ Center speaker ...................................x 1

❏ Surround speaker ...............................x 4

Select magnetically shielded speakers. The

minimum required speakers are two front speakers.

The priority of the requirement of other speakers is

as follows:

1. Two surround speakers

2. One center speaker

3. One (or two) surround back speaker(s)

❏ Active subwoofer ....................................x 1

Select an active subwoofer equipped with an RCA

input jack.

❏ Speaker cable ..........................................x 7

❏ Subwoofer cable .....................................x 1

Select a monaural RCA cable.

❏ DVD player ...............................................x 1

Select DVD player equipped with coaxial digital

audio output jack and composite video output

jack.

❏ Video monitor...........................................x 1

Select a TV monitor, video monitor or projector

equipped with a composite video input jack.

❏ Video cable ..............................................x 2

Select RCA composite video cables.

❏ Digital coaxial audio cable .....................x 1

Quick start guide

Front right

speaker

Subwoofer

Surround back

right speaker

Surround left

speaker

Front left

speaker

Surround back left

speaker

Surround right

speaker

Center

speaker

Video monitor

DVD player

Enjoy DVD playback!

Step 1: Set up your speakers

☞

P. 6

Step 2: Connect your DVD player

and other components

Step 3: Turn on the power and

start playback

☞

P. 7

☞

P. 8

Preparation: Check the items

QUICK START GUIDE

6 En

Place your speakers in the room and connect them to this

unit.

1 Place your speakers and subwoofer in the

room.

2 Connect speaker cables to each speaker.

3 Connect each speaker cable to the

corresponding speaker terminal of this unit.

1 Make sure that this unit and the subwoofer are

unplugged from the AC wall outlets.

2 Twist the exposed wires of the speaker cables

together to prevent short circuits.

3 Do not let the bare speaker wires touch each other.

4 Do not let the bare speaker wires touch any metal

part of this unit.

Be sure to connect the left channel (L), right channel

(R), “+” (red) and “–” (black) properly.

Front speakers and center speaker

Surround and surround back speakers

4 Connect the subwoofer cable to the

SUBWOOFER PRE OUT jack of this unit and

the input jack of the subwoofer.

Step 1: Set up your speakers

AC IN

AC OUTLETS

SWITCHED

HOLDER

WRENCH

SPEAKERS

CENTER

BI-AMP

SURROUND BACK/

PRESENCE/ZONE 2/ZONE 3

SP1

FRONT

SURROUND

ZONE 2/ZONE 3

SINGLE

SP2

ANTENNA

FM

GND

AM

75Ω UNBAL.

VIDEO

S VIDEO

MONITOR OUT

VIDEO

REMOTE

PHONO

GND

CD TV

HDMI

COMPONENT VIDEO

AUDIO

DOCK

DIGITAL INPUT

MULTI CH INPUT

PRE OUT

TRIGGER OUT

RS-232C

DIGITAL OUTPUT

ZONE OUT

SUB

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3

CD

D

V

D

V

R

COAXIAL

1

2

TV

BD/

HD DVD

CBL/

SAT

MD/

CD-R

DVD DVR

OPTICAL

987

65

4

321

SB(8CH)

DVD

(REC)

(PLAY)

IN

OUT

CD-R

MD/

BD/HD DVD

VCR

DVR

CBL/SAT

OUT OUT

ININ

BD/HD DVD

DVD

CBL/SAT

MONITOR OUT

Y

P

R

Y

P

R

P

B

P

B

IN

OUT

DVR

CBL/

SAT

DVD

BD/

HD DVD

OUT

+

++

A B C

R

L

R

L

R

L

+++

R

L

++

R

L

++

R

L

IN2

IN3

IN4

IN1

SUBWOOFER PRE OUT Speaker terminals

12 3 4

To the front left

speaker

To the front right

speaker

Loosen Insert

Speaker terminal wrench

To the center

speaker

Tighten

To the surround

back

right speaker

To the surround

back left

speaker

To the surround right

speaker

To the surround left

speaker

SUBWOOFER PRE OUT jack

Input jack

AV receiverSubwoofer

Subwoofer cable

Quick start guide

7 En

INTRODUCTION

English

1 Connect the digital coaxial audio cable to the

digital coaxial audio output jack of your DVD

player and the DVD DIGITAL INPUT COAXIAL

jack of this unit.

2 Connect the video cable to the composite

video output jack of your DVD player and

DVD VIDEO jack of this unit.

3 Connect the video cable to the VIDEO

MONITOR OUT jack of this unit and the video

input jack of your video monitor.

4 Connect the supplied power cable to this unit

and then plug of the power cable and other

components into the AC wall outlet.

y

For details about connecting the power cable, see page 24.

■ For other connections

• Other speaker combinations ☞ P. 12

• Information on jacks and cable plugs ☞ P. 15

• Information on HDMI™ ☞ P. 16

• TV monitor or projector ☞ P. 18

• Other components ☞ P. 19

• External amplifier ☞ P. 21

• Multi-format player or external

decoder ☞ P. 22

• Yamaha iPod universal dock or

Bluetooth wireless audio receiver ☞ P. 22

•FM/AM antennas ☞ P. 23

• USB memory device or

USB portable audio player ☞ P. 23

Step 2: Connect your DVD player

and other components

AC IN

AC OUTLETS

SWITCHED

HOLDER

WRENCH

SPEAKERS

CENTER

BI-AMP

SURROUND BACK/

PRESENCE/ZONE 2/ZONE 3

SP1

FRONT

SURROUND

ZONE 2/ZONE 3

SINGLE

SP2

ANTENNA

FM

GND

AM

75Ω UNBAL.

VIDEO

S VIDEO

MONITOR OUT

VIDEO

REMOTE

PHONO

GND

CD TV

HDMI

COMPONENT VIDEO

AUDIO

DOCK

DIGITAL INPUT

MULTI CH INPUT

PRE OUT

TRIGGER OUT

RS-232C

DIGITAL OUTPUT

ZONE OUT

SUB

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3

CD

D

V

D

V

R

COAXIAL

1

2

TV

BD/

HD DVD

CBL/

SAT

MD/

CD-R

DVD DVR

OPTICAL

987

65

4

321

SB(8CH)

DVD

(REC)

(PLAY)

IN

OUT

CD-R

MD/

BD/HD DVD

VCR

DVR

CBL/SAT

OUT OUT

ININ

BD/HD DVD

DVD

CBL/SAT

MONITOR OUT

Y

P

R

Y

P

R

P

B

P

B

IN

OUT

DVR

CBL/

SAT

DVD

BD/

HD DVD

OUT

+

++

A B C

R

L

R

L

R

L

+++

R

L

++

R

L

++

R

L

IN2

IN3

IN4

IN1

Make sure that this unit and the DVD

player are unplugged from the AC

wall outlets.

VIDEO MONITOR OUTDVD VIDEO

DVD DIGITAL INPUT

COAXIAL

Digital coaxial

audio output

jack

Digital coaxial audio

cable

DVD DIGITAL INPUT

COAXIAL jack

DVD player

AV receiver

Composite video

output jack

Video cable

DVD VIDEO jack

DVD player

AV receiver

Video monitor

AV receiver

Video cable

VIDEO MONITOR

OUT jack

Video input jack

Quick start guide

8 En

1 Turn on the video monitor connected to this

unit.

2 Press

A

MASTER ON/OFF inward to the ON

position on the front panel.

3 Rotate the

C

INPUT selector to set the input

source to “DVD”.

4 Start playback of the desired DVD on your

player.

5 Rotate

Q

VOLUME to adjust the volume.

6 To set this unit to the standby mode, press B

MAIN ZONE ON/OFF.

y

For details about turning on/off this unit and the standby

mode, see pages 25.

■ For other operations

• Optimizing the speaker parameters

automatically ☞ P. 29

• Basic playback operations ☞ P. 34

• Sound field programs ☞ P. 38

• Pure high-fidelity sounds ☞ P. 45

• FM/AM radio tuning ☞ P. 46

• iPod playback ☞ P. 52

• Bluetooth component playback ☞ P. 54

• USB content playback ☞ P. 55

Step 3: Turn on the power and start

playback

Check the type of the connected speakers.

If the speakers are 6-ohm speakers, set “SPEAKER

IMP.” to “6Ω MIN” before using this unit (page 25).

You can also use 4-ohm speakers as the front speakers

(page 93).

9 En

PREPARATION

English

• The TRIGGER OUT jacks are control expansion terminals for

custom installation.

• The RS-232C terminal is a control expansion terminal for

factory use only. Consult your dealer for details.

Connections

Rear panel

AC IN

AC OUTLETS

SWITCHED

HOLDER

WRENCH

SPEAKERS

CENTER

BI-AMP

SURROUND BACK/

PRESENCE/ZONE 2/ZONE 3

SP1

FRONT

SURROUND

ZONE 2/ZONE 3

SINGLE

SP2

ANTENNA

FM

GND

AM

75Ω UNBAL.

VIDEO

S VIDEO

MONITOR OUT

VIDEO

REMOTE

PHONO

GND

CD TV

HDMI

COMPONENT VIDEO

AUD IO

DOCK

DIGITAL INPUT

MULTI CH INPUT

PRE OUT

TRIGGER OUT

RS-232C

DIGITAL OUTPUT

ZONE OUT

SUB

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3

CD

D

V

D

V

R

COAXIAL

1

2

TV

BD/

HD DVD

CBL/

SAT

MD/

CD-R

DVD DVR

OPTICAL

987

65

4

321

SB(8CH)

DVD

(REC)

(PLAY)

IN

OUT

CD-R

MD/

BD/HD DVD

VCR

DVR

CBL/SAT

OUT OUT

ININ

BD/HD DVD

DVD

CBL/SAT

MONITOR OUT

Y

P

R

Y

P

R

P

B

P

B

IN

OUT

DVR

CBL/

SAT

DVD

BD/

HD DVD

OUT

+

++

A B C

R

L

R

L

R

L

+++

R

L

++

R

L

++

R

L

IN2

IN3

IN4

IN1

0A9

8

B

2314567

Name Page

1 HDMI jacks 16

2 COMPONENT VIDEO jacks 15

3 Audio component jacks 15

REMOTE IN/OUT jacks 22, 90

4 Video component jacks 15

5 ANTENNA terminals 23

6 VOLTAGE SELECTOR

(Asia and General models only)

24

7 AC IN 24

AC OUTLET(S) 24

8 DOCK terminal 22

9 DIGITAL INPUT/OUTPUT jacks 15

0 TRIGGER OUT jacks —

A RS-232C terminal —

B MULTI CH INPUT jacks 22

PRE OUT jacks 21

ZONE OUT jacks 90

Speaker terminals 12

WRENCH HOLDER 14

Notes

10 En

Connections

The speaker layout below shows the speaker setting we recommend.

y

• 7.1-channel speaker layout is highly recommended for playback of the high definition digital audio sources (Dolby TrueHD, DTS-HD

Master Audio, etc.) with sound field programs.

• We recommend that you add the presence speakers for the effect sounds of the CINEMA DSP sound field program.

7.1-channel speaker layout

6.1-channel speaker layout

5.1-channel speaker layout

Placing speakers

FR

FL

SBR

SBL

SL

SR

C

SW

60˚

30˚

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

30 cm (12 in) or more

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

FR

FL

SB

SL

SR

C

SW

FR

FL

SL

SR

SW

C

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

11 En

Connections

PREPARATION

English

■ Speaker types

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers at an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds.

For 5.1-channel speaker layout, place these speakers

farther back compared with the placement in the 7.1-

channel speaker layout.

Surround back left and right speakers (SBL and

SBR) / Surround back speaker (SB)

The surround back speakers supplement the surround

speakers and provide more realistic front-to-back

transitions.

For 6.1-channel speaker layout, surround back left and

right channel signals are mixed down and output at the

single surround back speaker by configuring the “SUR.B

L/R SP” setting (page 68).

For 5.1-channel speaker layout, surround back left and

right channel signals are output at the surround left and

right speakers by configuring the “SUR.B L/R SP” setting

(page 68).

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as

the Yamaha Active Servo Processing Subwoofer System,

is effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the high

fidelity sound of the LFE (low-frequency effect) channel

included in bitstreams and multi-channel PCM sources.

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the front speakers. Turn it

slightly toward the center of the room to reduce wall

reflections.

■ Presence left and right speakers

(PL and PR)

The presence speakers supplement the sound from the front

speakers with extra ambient effects produced by the sound

field programs (page 38). We recommend that you use the

presence speakers especially for the CINEMA DSP sound

field programs. To use the presence speakers, connect the

speakers to SP1 speaker terminals and then set

“PRESENCE SP” to “YES” (page 68).

For other speaker combinations

You can enjoy multi-channel sources with sound field

programs by using a speaker combination other than

the 7.1/6.1/5.1-channel speaker combinations.

Use the automatic setup feature (page 29) or set the

“SPEAKER MENU” parameters (page 67) to output

the surround sounds at the connected speakers.

FR

PRPL

C

FL

1.8 m (6 ft)

0.5 to 1 m (1 to 3 ft) 0.5 to 1 m (1 to 3 ft)

1.8 m (6 ft)

12 En

Connections

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,

this unit cannot reproduce the input sources accurately.

• A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a

stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the

plain cable to the “–” (black) terminals.

• You can connect both surround back and presence speakers to this unit, however they do not output sound simultaneously. This unit

automatically switches the presence speakers and surround back speakers depending on the input sources and the selected sound field

programs.

■ 7.1-channel speaker connection

Connecting speakers

Caution

• Before connecting the speakers, make sure that this unit is turned off (page 25).

• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could

damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the

speakers away from the monitor.

• If you are to use 6-ohm speakers, be sure to set “SPEAKER IMP.” to “6Ω MIN” before using this unit (page 25).

You can also use 4-ohm speakers as the front speakers (page 93).

Notes

SPEAKERS

CENTER

BI-AMP

SURROUND BACK/

PRESENCE/ZONE 2/ZONE 3

SP1

FRONT

SURROUND

ZONE 2/ZONE 3

SINGLE

SP2

PRE OUT

WOOFER

+

++

R

L

R

L

+++

R

L

++

R

L

++

R

L

Front speakers

Surround speakers

Presence speakers

(page 11) or

Zone 2/Zone 3

speakers

(page 90)

Subwoofer

Left

Center speaker

Surround back speakers

Right

Left

Right

Zone 2/Zone 3 speakers

(page 90)

13 En

Connections

PREPARATION

English

■ 6.1-channel speaker connection

■ 5.1-channel speaker connection

SPEAKERS

CENTER

BI-AMP

SURROUND BACK/

PRESENCE/ZONE 2/ZONE 3

SP1

FRONT

SURROUND

ZONE 2/ZONE 3

SINGLE

SP2

PRE OUT

SUB

WOOFER

+

++

R

L

R

L

+ + +

R

L

++

R

L

++

R

L

Surround back speaker

Front speakers

Surround speakers

Presence speakers

(page 11) or

Zone 2/Zone 3 speakers

(page 90)

Subwoofer

Center speaker

Left

Right

Zone 2/Zone 3

speakers

(page 90)

SPEAKERS

CENTER

BI-AMP

SURROUND BACK/

PRESENCE/ZONE 2/ZONE 3

SP1

FRONT

SURROUND

ZONE 2/ZONE 3

SINGLE

SP2

PRE OUT

SUB

WOOFER

+

++

R

L

R

L

+++

R

L

++

R

L

++

R

L

Front speakers

Surround speakers

Subwoofer

Center speaker

Left

Right

Zone 2/Zone 3

speakers

(page 90)

Front speakers for the

bi-amplification

connections

(page 14)

Presence speakers

(page 11) or

Zone 2/Zone 3 speakers

(page 90)

14 En

Connections

■ Connecting the speaker cable

1 Remove approximately 10 mm (0.4 in) of

insulation from the end of each speaker

cable and then twist the exposed wires of the

cable together to prevent short circuits.

2 Loosen the knob using the supplied speaker

terminal wrench, insert one bare wire into the

hole and then tighten the knob.

3 Hook the speaker terminal wrench onto

WRENCH HOLDER on the rear panel of this

unit when not in use.

■ Connecting to the SP2 speaker

terminals

Connect Zone 2 or Zone 3 speakers to these terminals

(page 90).

Open the tab, insert one bare wire into the hole

and then close the tab.

■ Connecting the banana plug

(Except U.K., Europe, Asia and Korea

models)

Tighten the knob using the supplied speaker

terminal wrench and then insert the banana plug

into the end of the terminal.

y

You can also use the banana plug with the SP2 speaker

terminals. Open the tab and then insert one banana plug into the

hole on the terminal. Do not close the tab after connecting the

banana plug.

■ Using bi-amplification connections

You can make bi-amplification connections to one speaker

system which supports bi-amplification connection as

shown below. To activate the connections, configure the

“BI-AMP” setting (page 94).

When you make the conventional connection with the speakers,

make sure that the shorting bars are put into the terminals of the

speakers appropriately. Refer to the instruction manuals of the

speakers for details.

10 mm (0.4 in)

Loosen Insert

Speaker terminal wrench

Tighten

Open the tab Insert Close the tab

Caution

Remove the shorting bars or bridges of your speakers to

separate the LPF (low pass filter) and HPF (high pass filter)

crossovers.

Note

Banana plug

BI-AMP

SURROUND BACK/

FRONT

SINGLE

++

+

R

L

SURROUND

+ +

R

L

This unit

LeftRight

Front speakers

15 En

Connections

PREPARATION

English

This unit has three types of audio jacks, three types of video jacks and HDMI jacks. You can choose the connection

method depending on the component to be connected.

■ Audio jacks

AUDIO jacks

For conventional analog audio signals transmitted via left

and right analog audio cables. Connect red plugs to the

right jacks and white plugs to the left jacks.

COAXIAL jacks

For digital audio signals transmitted via coaxial digital

audio cables.

OPTICAL jacks

For digital audio signals transmitted via optical digital

audio cables.

You can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. When you connect components to both the

COAXIAL and OPTICAL jacks, priority is given to the signals

input at the COAXIAL jack. All digital input jacks are

compatible with up to 96-kHz sampling digital signals.

■ Video jacks

VIDEO jacks

For conventional composite video signals transmitted via

composite video cables.

S VIDEO jacks

For S-video signals, separated into the luminance (Y) and

chrominance (C) video signals transmitted on separate

wires of S-video cables.

COMPONENT VIDEO jacks

For component video signals, separated into the

luminance (Y) and chrominance (P

B, PR) video signals

transmitted on separate wires of component video cables.

y

This unit is equipped with the video conversion function.

(page 17)

Information on jacks and cable plugs

Note

COAXIAL

DIGITAL

AUDIO

OPTICAL

DIGITAL

R

L

C

O

R

L

Left and right

analog audio

cable plugs

Optical

digital

audio cable

plug

Coaxial

digital audio

cable plug

(Red)(White) (Orange)

VIDEO S VIDEO

COMPONENT VIDEO

Y

R

P

B

P

PB

Y

P

R

S

V

Composite

video cable

plug

S-video

cable plug

Component

video cable

plugs

(Yellow) (Green) (Blue) (Red)

16 En

Connections

This unit has four HDMI input jacks and one HDMI output jack for digital audio and video signal input/output.

■ HDMI jack and cable plug

y

• We recommend that you use a commercially available HDMI

cable shorter than 5 meters (16 feet) with the HDMI logo

printed on it.

• Use a conversion cable (HDMI jack

↔ DVI-D jack) to connect

this unit to other DVI components.

• You can check the potential problem about the HDMI

connection (page 36).

• This unit is equipped with the video conversion function

(page 17).

• Do not disconnect or connect the cable or turn off the power of

the HDMI components connected to the HDMI OUT jack of

this unit while data is being transferred. Doing so may disrupt

playback or cause noise.

• The HDMI OUT jack outputs the audio signals input at the

HDMI input jacks only.

• If you turn off the video monitor connected to the HDMI OUT

jack via a DVI connection, the connection may fail.

■ HDMI signal compatibility with this unit

Audio signals

y

• If the input source component can decode the bitstream audio

signals of audio commentaries, you can play back the audio

sources with the audio commentaries mixed down by using the

following connections:

– multi-channel analog audio input (page 22)

– DIGITAL INPUT OPTICAL (or COAXIAL)

• Refer to the instruction manuals of the input source component,

and set the component appropriately.

• When CPPM copy-protected DVD audio is played back, video

and audio signals may not be output depending on the type of

the DVD player.

• This unit is not compatible with HDCP-incompatible HDMI or

DVI components.

• To decode the audio bitstream signals on this unit, set the input

source component appropriately so that the component outputs

the audio bitstream signals directly (does not decode the

bitstream signals on the component).

• This unit is not compatible with the audio commentary features

(for example, the special audio contents downloaded via

Internet) of Blu-ray Disc or HD DVD. This unit does not play

back the audio commentaries of the Blu-ray Disc or HD DVD

contents.

Video signals

This unit is compatible with the video signals of the

following resolutions:

– 480i/60 Hz

– 576i/50 Hz

– 480p/60 Hz

– 576p/50 Hz

– 720p/60 Hz, 50 Hz

– 1080i/60 Hz, 50 Hz

– 1080p/60 Hz, 50 Hz, 24Hz

Compatibility with Deep Color and x.v.Color

video signals

This unit accepts Deep Color (30 or 36-bit) and x.v.Color

video signals. To output those video signals from the

HDMI OUT jack without any processing, set “HDMI

RES.” to “THRGH” (page 73).

If the video monitor is not compatible with Deep Color or

x.v.Color video signals, the video source may not be played

back correctly.

■ Default input assignment of HDMI input

jacks

Information on HDMI™

Notes

Audio signal

types

Audio signal

formats

Compatible

media

2ch Linear

PCM

2ch, 32-192 kHz,

16/20/24 bit

CD, DVD-Video,

DVD-Audio, etc.

Multi-ch

Linear PCM

8ch, 32-192 kHz,

16/20/24 bit

DVD-Audio, etc.

DSD 2/5.1ch,

2.8224 MHz,1 bit

SACD, etc.

Bitstream Dolby Digital,

DTS

DVD-Video, etc.

Bitstream (High

definition audio)

Dolby TrueHD,

Dolby Digital Plus,

DTS-HD Master

Audio, DTS-HD

High Resolution

Audio

Blu-ray Disc,

HD DVD, etc.

HDMI

HDMI cable plug

Notes

Note

HDMI input jack Assigned input source

IN1 BD/HD DVD

IN2 DVD

IN3 CBL/SAT

IN4 DVR

La page charge ...

Yamaha RX-V1900 Le manuel du propriétaire

Yamaha RX-V1900 Le manuel du propriétaire

dans d''autres langues

Autres documents