SICK PowerProx Small Analog - WTT190L-Axxxx Mode d'emploi

SICK
Marque
SICK
Modèle
PowerProx Small Analog - WTT190L-Axxxx
Taper
Mode d'emploi
O P E R A T I N G I N S T R U C T I O N S
PowerProx Small Analog - WTT190L-Axxxx
MultiTask photoelectric sensor
O P E R A T I N G I N S T R U C T I O N S
PowerProx Small Analog - WTT190L-Axxxx
MultiTask photoelectric sensor
de
en
es
fr
it
ja
pt
ru
zh
Described product
PowerProx Small Analog - WTT190L-Axxxx
Manufacturer
SICK AG
Erwin-Sick-Str. 1
79183 Waldkirch
Germany
Legal information
This work is protected by copyright. Any rights derived from the copyright shall be
reserved for SICK AG. Reproduction of this document or parts of this document is only
permissible within the limits of the legal determination of Copyright Law. Any modifica‐
tion, abridgment or translation of this document is prohibited without the express writ‐
ten permission of SICK AG.
The trademarks stated in this document are the property of their respective owner.
© SICK AG. All rights reserved.
Original document
This document is an original document of SICK AG.
2
8020032.ZX33 | SICK
Subject to change without notice
Contents
1 Safety information............................................................................ 4
1.1 Safety notes.............................................................................................. 4
2 Product description........................................................................... 4
2.1 Intended use............................................................................................. 4
2.2 Dimensional drawing................................................................................ 5
3 Commissioning.................................................................................. 5
3.1 Check the application conditions:........................................................... 5
3.2 Mounting................................................................................................... 6
3.3 Electronics................................................................................................. 7
3.4 Functioning of the programmable input.................................................. 7
3.5 Alignment.................................................................................................. 7
4 Configuration..................................................................................... 8
4.1 Setting the analog output........................................................................ 8
4.2 Setting the switching output via the teach-in quick access button
(-/Q1)......................................................................................................... 8
4.3 Setting the analog output, switching output, and other sensor config‐
urations via the menu.............................................................................. 9
4.4 Pushbutton lock........................................................................................ 12
5 Troubleshooting................................................................................. 12
5.1 Troubleshooting........................................................................................ 12
5.2 Table: Fault diagnosis............................................................................... 12
6 Technical data.................................................................................... 12
6.1 Technical data........................................................................................... 12
7 Disassembly and disposal............................................................... 13
8 Maintenance...................................................................................... 13
CONTENTS
8020032.ZX33 | SICK
Subject to change without notice
3
1 Safety information
1.1 Safety notes
■
Read the operating instructions before commissioning.
■
Connection, mounting, and setting may only be performed by trained specialists.
■
Not a safety component in accordance with the EU Machinery Directive.
■
UL: Only for use in applications in accordance with NFPA 79. These devices shall
be protected by a 1 A fuse suitable for 30 V DC. Adapters listed by UL with connec‐
tion cables are available. UL Environmental Rating: Enclosure type 1
■
When commissioning, protect the device from moisture and contamination.
■
These operating instructions contain information required during the life cycle of
the sensor.
EN/IEC 60825-1:2014
IEC60825-1:2007
LASERKLASSE 1
Laser
1
Maximum pulse power < 64 mW
Puls length: 9 ns
Wavelength: 650 nm
Complies with 21 CFR 1040.10
and 1040.11 except for deviations
pursuant to Laser Notice No. 50,
dated June 24, 2007
ATTENTION
WARNING: Interruption, manipulation or incorrect use can lead to hazardous exposure
due to laser radiation.
2 Product description
2.1 Intended use
The WTT190L-Axxxx is an opto-electronic photoelectric proximity sensor (referred to as
“sensor” in the following) for the optical, non-contact detection of objects. If the product
is used for any other purpose or modified in any way, any warranty claim against SICK
AG shall become void.
Photoelectric proximity sensor with background suppression and analog distance value
output.
1 SAFETY INFORMATION
4
8020032.ZX33 | SICK
Subject to change without notice
2.2 Dimensional drawing
2
1
4.8
(0.19)
4
3
5
à ß 9
6
7
8
28.3 (1.11)
17
(0.67) 32.8 (1.29)
9
(0.35)
16
(0.63)
44.4 (1.75)
39.2 (1.54)
2.6
(0.1)
3.7 (0.12)
1.2
(0.05)
1.9
(0.07)
Ø 3.1
(0.12)
7
(0.28)
6 (0.24)
2.8 (0.11)
17.4 (0.69)
3
32.8 (1.29)
39.2 (1.54)
2.6
(0.1)
3.1
(0.12)
1.2
(0.05)
1.9
(0.07)
Ø 3.1
(0.12)
7 (0.28)
6 (0.24)
2.8 (0.11)
WTT190L-A2xxx WTT190L-A1xxx
WTT190L-A3xxx
1
Receiver
2
Sender
3
Connection
4
RUN button
5
(+) button
6
Output display (orange)
7
Stability display (green/red), laser off display (off)
8
Output display (orange)
9
(-/Q1) button
ß
Display
à
(SET) button
3 Commissioning
3.1 Check the application conditions:
Analog output:
Refer to TableTechnical data and Diagram H3, H4 for the accuracy specifications of the
analog output.
Switching output:
Check the application conditions: Adjust the sensing range and distance to the object
or background and the remission capability of the object according to the correspond‐
ing diagram [H1, H2] (x = sensing range, y = minimum distance between the object and
background in mm (object remission / background remission)). Remission: 6% = black,
90% = white (referring to standard white as per DIN 5033).
The minimum distance (= y) for background suppression can be read from diagram
[H15] as follows:
Example: x = 1,000 mm, y = 20 mm. That is, the background is suppressed at a dis‐
tance of > 20 mm from the sensor.
PRODUCT DESCRIPTION 2
8020032.ZX33 | SICK
Subject to change without notice
5
200
(7.87)
160
(6.3)
120
(4.72)
80
(3.15)
40
(1.57)
0
Min. distance from object to background in mm (inch)
0
1,000
(39.37)
2,000
(78.74)
3,000
(119.11)
Distance in mm (inch)
1
2
3
5
4
Figure: H-1 - Small teach and analog 6%/90%
16%/90% AVG1
26%/90% AVG4
36%/90% AVG16
46%/90% AVG64
56%/90% AVG256
180
(7.09)
160
(6.03)
120
(4.72)
80
(3.15)
40
(1.57)
140
(5.51)
100
(3.94)
60
(2.36)
20
(0.79)
0
Min. distance from object to background in mm (inch)
0
1,000
(39.37)
2,000
(78.74)
3,000
(118.11)
Distance in mm (inch)
1
2
3
4
5
Figure: H-2 - Small teach and analog 90%/90%
190%/90% AVG1
290%/90% AVG4
390%/90% AVG16
490%/90% AVG64
590%/90% AVG256
90
(3.54)
80
(3.15)
60
(2.36)
40
(1.57)
20
(0.79)
70
(2.76)
50
(1.97)
30
(1.18)
10
(0.39)
0
Repeatability (1σ) in mm (inch)
0
1,000
(39.37)
2,000
(78.74)
3,000
(118.11)
Distance in mm (inch)
1
2
3
4
5
Figure: H-3 - Small analog 6%
16% AVG1
26% AVG4
36% AVG16
46% AVG64
56% AVG256
35
(1.38)
30
(1.18)
25
(0.98)
20
(0.79)
15
(0.59)
10
(0.39)
5
(0.2)
0
Repeatability (1σ) in mm (inch)
0
1,000
(39.37)
2,000
(78.37)
3,000
(118.11)
Distance in mm (inch)
1
5
3
2
4
Figure: H-4 - Small analog 90%
190% AVG1
290% AVG4
390% AVG16
490% AVG64
590% AVG256
3.2 Mounting
Mount the sensor using a suitable mounting bracket (see the SICK range of acces‐
sories).
Note the sensor's maximum permissible tightening torque of 0.8 Nm.
Note the preferred direction of the object relative to the sensor [F].
3 COMMISSIONING
6
8020032.ZX33 | SICK
Subject to change without notice
3.3 Electronics
The sensors must be connected in a voltage-free state (U
V
= 0 V). The information in
the graphics [B] must be observed, depending on the connection type:
– Male connector connection: pin assignment
– Cable: wire color
+(L+)
–(M)
Q
a
Q1
MF
in
brn
wht
blk
gra
blu
Figure: B: WTT190L-A15x2B
+(L+)
–(M)
Q
a
Q1
MF
in
brn
wht
blk
gra
blu
1
2
3
4
5
Figure: B-2: -A35x2
Q1/MF
in
4
+(L+)
–(M)
Q
a
brn
wht
blk
blu
1
2
3
Figure: B-3: -A22x2
Only apply voltage/switch on the voltage supply (U
V
> 0 V) once all electrical connec‐
tions have been established. The green LED indicator lights up on the sensor.
Explanations of the connection diagram (Graphic B):
MF
in
= multifunctional, programmable input
3.4 Functioning of the programmable input
Value Notes
PNP mode Deactivated < 5.0 V Also deactivated when not connected
Active > 10.0 V Max. applied voltage not higher than
UV
NPN mode Deactivated > 10.0 V Max. applied voltage not higher than
UV
Active < 4.0 V Also active when not connected
The programmable input must be active for the durations specified below (e.g., U
> 10.0 V in PNP mode ) in order to set the corresponding functions. For a description of
the available functions and how to select them via the menu, see „Setting the analog
output, switching output, and other sensor configurations via the menu“, page 9
Function Minimum duration Maximum duration
Laser shutdown 4 ms -
External teach-in Q1 4 ms -
3.5 Alignment
Align the sensor with the object. Select the position so that the red emitted light beam
hits the center of the object. You must ensure that the optical opening (front screen) of
the sensor is completely clear [F]. We recommend making the adjustments using an
object with a low remission.
COMMISSIONING 3
8020032.ZX33 | SICK
Subject to change without notice
7
Figure: E
4 Configuration
Perform configuration:
4.1 Setting the analog output
The analog output is configured as follows at the factory:
4 mA = 0 mm
20 mA = 3,000 mm
For additional settings, see „Setting the analog output, switching output, and other sen‐
sor configurations via the menu“, page 9.
4.2 Setting the switching output via the teach-in quick access button (-/Q1)
The sensing range is adjusted by pressing the teach-in quick access button for > 1 s.
Do not operate the teach-in buttons using sharp objects. We recommend placing the
sensing range in the object, e.g., see Graphic E. Once the sensing range has been
adjusted, the object is removed from the path of the beam, which causes the back‐
ground to be suppressed and the switching output to change (see Graphic C).
The switching output is adjusted and ready for operation. Refer to Graphic C to check
the function. If the switching output fails to behave in accordance with Graphic C, check
application conditions. See section Fault diagnosis.
Q1
Figure 1: F
3 COMMISSIONING
8
8020032.ZX33 | SICK
Subject to change without notice
Q (PNP)
Q (NPN)
L
L
D
D
1
0
1
0
1
0
1
0
Figure 2: C
4.3 Setting the analog output, switching output, and other sensor configurations via
the menu
As an alternative, the analog and switching output can also be set via the menu. Fur‐
ther sensor configurations can also be performed via the menu. The menu is accessed
by briefly pressing the Set button for < 1 s. Graphic K describes how to navigate within
the menu.
Figure 3: K
CONFIGURATION
4
8020032.ZX33 | SICK
Subject to change without notice
9
The table below explains the abbreviations and displays the possible settings.
Table 1: Analog and teach parameter list
Name Display Description Value
selection
Display Initial
value
Description
MF MF Enables the configuration of
the multifunctional input/
output.
OFF, OUT,
TCH, LSR,
LSN
oFF The external input has no
function.
out In 4-pin devices: Pin 4 func‐
tions as a switching output.
tch For 5-pin devices: The exter‐
nal input is a teach-in input.
For a functional description,
see see „Electronics“, page 7
LSr X The external input functions
as a laser shutdown, high-
active.
LSn The external input functions
as a laser shutdown, low-
active.
N_P n_P Switchover between PNP/NPN
mode.
PNP, NPN PnP X Inputs and outputs are in PNP
mode.
nPn Inputs and outputs are in NPN
mode.
V_A U_A Switchover between current/
voltage output.
CUR, VLT cur X The analog output functions
as a current output.
ULt The analog output functions
as a voltage output.
L_D L_D Switchover between light/
dark switching
LON, DON,
STB, STD
Lon X Light switching: The switching
output switches on when the
object is closer than the
taught sensing range.
don Dark switching: The switching
output switches off when the
object is closer than the
taught sensing range.
Stb The switching output Q1
issues the stability of the
measured value acquisition
(therefore corresponds to the
LED stability display). Light
switching functionality.
Std The switching output Q1
issues the stability of the
measured value acquisition
(therefore corresponds to the
LED stability display). Dark
switching functionality.
AVG AUG Setting the moving arithmetic
average
1, 4, 16,
64, 256
64 64 Sets the number of values
across which a moving arith‐
metic average is established
when the signal is output.
This smooths the signal out‐
put. The possible values are
1, 4, 16, 64, or 256 (e.g., 1 =
no averaging, 256 = average
across 256 values)
4 CONFIGURATION
10
8020032.ZX33 | SICK
Subject to change without notice
Name Display Description Value
selection
Display Initial
value
Description
ALM ALM Behavior during non-stable
distance measurement
CLP, HLD cLP X If the distance measurement
is not stable, the maximum
current/maximum voltage at
the analog output is issued.
hLd If the distance measurement
is not stable, the most
recently valid current/voltage
value at the analog output is
maintained.
RST rSt Reset to factory settings NO, YES no X No reset.
YES Reset all values to factory set‐
tings with the exception of the
PNP/NPN selection.
DSP dSP Display settings ON, OFF on X Display shows display value in
cm.
oFF Display switches off 30 sec‐
onds after an operating but‐
ton was last pressed.
DLY dLY Setting the time functions for
the switching output.
OFF, OFD,
OND, SHT
oFF X No time function activated.
oFd Switch-off delay, adjustable
from 0 … 999 ms.
ond Switch-on delay, adjustable
from 0 … 999 ms.
Sht Single shot, adjustable from 0
… 999 ms.
NER nEr Distance assignment for 4 mA
or 0.04 V.
0 … 300 0 0 Value range 0 … 300
FAR FAr Distance assignment for
20 mA or 10 V.
0 … 300 300 300 Value range 0 … 300
Q_1 q_I Distance assignment for
switching output Q1.
0 … 300 300 300 Value range 0 … 300
The factory setting of the analog output can be adjusted via the menu items ner and far:
The ner value defines the distance assignment for 4 mA / 0.04 V.
The far value defines the distance assignment for 20 mA / 10 V.
If the switching output is to be set via the menu, adjust entry Q_1.
CONFIGURATION 4
8020032.ZX33 | SICK
Subject to change without notice
11
Press the Run button to leave the menu.
4.4 Pushbutton lock
Pushbutton lock on: Press the (Run) button for > 1 s
Pushbutton lock off: Press the (Run) button again for > 1 s
5 Troubleshooting
5.1 Troubleshooting
The Troubleshooting table indicates measures to be taken if the sensor stops working.
5.2 Table: Fault diagnosis
LED indicator/fault pattern /
LED indicator/fault pattern
Cause /
Cause
Measures /
Measures
Green LED does not light up /
Green LED does not light up
No voltage or voltage below
the limit values /
No voltage or voltage below
the limit values
Check the power supply,
check all electrical connec‐
tions (cables and plug connec‐
tions) /
Check the power supply,
check all electrical connec‐
tions (cables and plug connec‐
tions)
Green LED does not light up /
Green LED does not light up
Voltage interruptions /
Voltage interruptions
Ensure there is a stable power
supply without interruptions /
Ensure there is a stable power
supply without interruptions
Green LED does not light up /
Green LED does not light up
Sensor is faulty /
Sensor is faulty
If the power supply is OK,
replace the sensor /
If the power supply is OK,
replace the sensor
Yellow LED lights up, no object
in the path of the beam /
Yellow LED lights up, no object
in the path of the beam
Distance between the sensor
and the background is too
short /
/ Distance between the sen‐
sor and the background is too
short
Reduce the sensing range,
see graphic F /
Reduce the sensing range,
see graphic F
Object is in the path of the
beam, yellow LED does not
light up /
Object is in the path of the
beam, yellow LED does not
light up
Distance between the sensor
and the object is too long or
sensing range is set too
short /
Distance between the sensor
and the object is too long or
sensing range is set too short
Increase the sensing range,
see graphic F /
Increase the sensing range,
see graphic F
6 Technical data
6.1 Technical data
WTT190L-Axxx
Laser class 1
Sensing range 0.2 ... 3.0 m
1)
4 CONFIGURATION
12
8020032.ZX33 | SICK
Subject to change without notice
WTT190L-Axxx
Sensing range max. 0.2 ... 3.0 m
1)
Light spot diameter/distance < 12.0 mm / 3,0 m
Supply voltage V
S
DC 12 ... 30 V
Output current I
max.
≤ 100 mA
Max. switching frequency AVG 1: 833 Hz, AVG 4:
500 Hz, AVG 16: 147
Hz, AVG 64: 38 Hz, AVG
256: 10 Hz
2)3)4)
Max. response time AVG 1: 0.6 ms, AVG 4: 1
ms, AVG 16: 3.4 ms,
AVG 64: 13 ms, AVG
256: 51.4 ms
5)6)4)
Analog output 4 mA ... 20 mA (≤300
W) / 0 V ... 10 V
(≥10 kW) / switchable
Analog output resolution 10 bit
Distance value measuring range 0.2 ... 3.0 m
1)
Distance value reproducibility 5 ... 80 mm
1)7)
Accuracy typ. +/- 30 mm (0.2 ...
2.0 m); +/- 50 mm
(2.0 ... 3.0 m)
Enclosure rating IP 67
Protection class III
Circuit protection A, B, C
8)
Ambient operating temperature -30 ... +50 °C
9)
1)
Object with 6 % ... 90 % remission (based on standard white DIN 5033)
2)
With light / dark ratio 1:1
3)
Dependent on distance to object, distance to background, and switching threshold selected
4)
Signal transit time with resistive load
5)
Can be influenced via average filter.
6)
Equivalent to 1 ohm.
7)
A = UV-connections reverse polarity protected
B = inputs and output reverse-polarity protected
C = Interference suppression
8)
Where TU < –10 °C: warm-up time < 10 min; UV>=24 V.
7 Disassembly and disposal
The sensor must be disposed of according to the applicable country-specific regula‐
tions. Efforts should be made during the disposal process to recycle the constituent
materials (particularly precious metals).
8 Maintenance
SICK sensors are maintenance-free.
We recommend doing the following regularly:
•
Clean the external lens surfaces
•
Check the screw connections and plug-in connections
No modifications may be made to devices.
DISASSEMBLY AND DISPOSAL 7
8020032.ZX33 | SICK
Subject to change without notice
13
Subject to change without notice. Specified product properties and technical data are
not written guarantees.
8 MAINTENANCE
14
8020032.ZX33 | SICK
Subject to change without notice
B E T R I E B S A N L E I T U N G
PowerProx Small Analog - WTT190L-Axxxx
MultiTask-Lichtschranke
de
en
es
fr
it
ja
pt
ru
zh
Beschriebenes Produkt
PowerProx Small Analog - WTT190L-Axxxx
Hersteller
SICK AG
Erwin-Sick-Str. 1
79183 Waldkirch
Deutschland
Rechtliche Hinweise
Dieses Werk ist urheberrechtlich geschützt. Die dadurch begründeten Rechte bleiben
bei der Firma SICK AG. Die Vervielfältigung des Werks oder von Teilen dieses Werks ist
nur in den Grenzen der gesetzlichen Bestimmungen des Urheberrechtsgesetzes zuläs‐
sig. Jede Änderung, Kürzung oder Übersetzung des Werks ohne ausdrückliche schriftli‐
che Zustimmung der Firma SICK AG ist untersagt.
Die in diesem Dokument genannten Marken sind Eigentum ihrer jeweiligen Inhaber.
© SICK AG. Alle Rechte vorbehalten.
Originaldokument
Dieses Dokument ist ein Originaldokument der SICK AG.
16
8020032.ZX33 | SICK
Subject to change without notice
Inhalt
9 Zu Ihrer Sicherheit............................................................................. 18
9.1 Sicherheitshinweise.................................................................................. 18
10 Produktbeschreibung....................................................................... 18
10.1 Bestimmungsgemäße Verwendung......................................................... 18
10.2 Maßzeichnung........................................................................................... 19
11 Inbetriebnahme................................................................................. 19
11.1 Einsatzbedingungen prüfen:.................................................................... 19
11.2 Montage.................................................................................................... 20
11.3 Elektronik.................................................................................................. 21
11.4 Funtionsweise des programmierbaren Eingangs................................... 21
11.5 Ausrichtung............................................................................................... 21
12 Konfiguration..................................................................................... 22
12.1 Einstellung des Analogausgangs............................................................. 22
12.2 Einstellung des Schaltausgangs über die Teach-in-Schnellzugriffs‐
taste (-/Q1)................................................................................................ 22
12.3 Einstellung des Analogausgangs, des Schaltausgangs sowie weitere
Parametrierungen des Sensors über das Menü..................................... 23
12.4 Tastensperre............................................................................................. 26
13 Störungsbehebung............................................................................ 26
13.1 Störungsbehebung................................................................................... 26
13.2 Tabelle Fehlerdiagnose............................................................................. 26
14 Technische Daten.............................................................................. 27
14.1 Technische Daten..................................................................................... 27
15 Demontage und Entsorgung............................................................ 28
16 Wartung.............................................................................................. 28
INHALT
8020032.ZX33 | SICK
Subject to change without notice
17
9 Zu Ihrer Sicherheit
9.1 Sicherheitshinweise
■
Vor der Inbetriebnahme die Betriebsanleitung lesen.
■
Anschluss, Montage und Einstellung nur durch Fachpersonal.
■
Kein Sicherheitsbauteil gemäß EU-Maschinenrichtlinie.
■
UL: Nur zur Verwendung in Anwendungen gemäß NFPA 79. Diese Geräte müssen
mit einer für 30V DC geeigneten 1A-Sicherung abgesichert werden. Von UL gelis‐
tete Adapter mit Anschlusskabeln sind verfügbar. UL Environmental Rating: Enclo‐
sure type 1
■
Gerät bei Inbetriebnahme vor Feuchte und Verunreinigung schützen.
■
Diese Betriebsanleitung enthält Informationen, die während des Lebenszyklus des
Sensors notwendig sind.
EN/IEC 60825-1:2014
IEC60825-1:2007
LASERKLASSE 1
Laser
1
Maximale Pulsleistung: < 64 mW
Impulsdauer: 9 ns
Wellenlänge: 650 nm
Entspricht 21 CFR 1040.10
und 1040.11 mit Ausnahme von
Abweichungen nach
Laser-Hinweis 50, 24. Juni 2007
ACHTUNG
ACHTUNG: Eingriffe oder Manipulationen oder nicht bestimmungsgemäße Verwendung
kann zu gefährlicher Belastung durch Laser-Lichtstrahlung führen.
10 Produktbeschreibung
10.1 Bestimmungsgemäße Verwendung
Die WTT190L-Axxxx ist ein optoelektronischer Reflexions-Lichttaster (im Folgenden Sen‐
sor genannt) und wird zum optischen, berührungslosen Erfassen von Sachen einge‐
setzt. Bei jeder anderen Verwendung und bei Veränderungen am Produkt verfällt jegli‐
cher Gewährleistungsanspruch gegenüber der SICK AG.
Reflexionslichttaster mit Hintergrundausblendung und analoger Distanzwertausgabe.
9 ZU IHRER SICHERHEIT
18
8020032.ZX33 | SICK
Subject to change without notice
10.2 Maßzeichnung
2
1
4.8
(0.19)
4
3
5
à ß 9
6
7
8
28.3 (1.11)
17
(0.67) 32.8 (1.29)
9
(0.35)
16
(0.63)
44.4 (1.75)
39.2 (1.54)
2.6
(0.1)
3.7 (0.12)
1.2
(0.05)
1.9
(0.07)
Ø 3.1
(0.12)
7
(0.28)
6 (0.24)
2.8 (0.11)
17.4 (0.69)
3
32.8 (1.29)
39.2 (1.54)
2.6
(0.1)
3.1
(0.12)
1.2
(0.05)
1.9
(0.07)
Ø 3.1
(0.12)
7 (0.28)
6 (0.24)
2.8 (0.11)
WTT190L-A2xxx WTT190L-A1xxx
WTT190L-A3xxx
1
Empfänger
2
Sender
3
Anschluss
4
RUN Taste
5
(+) Taste
6
Ausgangsanzeige (orange)
7
Stabilitätsanzeige (grün / rot), Laser Aus Anzeige (aus)
8
Ausgangsanzeige (orange)
9
(-/Q1) Taste
ß
Anzeige
à
(SET) Taste
11 Inbetriebnahme
11.1 Einsatzbedingungen prüfen:
Analogausgang:
Die Genauigkeitsangaben des Analogausgangs entnehmen Sie der Tabelle Technische
Daten sowie Diagramm H3, H4.
Schaltausgang:
Einsatzbedingungen prüfen: Schaltabstand und Distanz zum Objekt bzw. Hintergrund
sowie Remissionsvermögen des Objektes mit dem zugehörigen Diagramm [vgl. H1, H2]
abgleichen (x = Schaltabstand, y = Mindestabstand zwischen Objekt und Hintergrund in
mm (Remission Objekt / Remission Hintergrund)). Remission: 6 % = schwarz, 90 % =
weiß (bezogen auf Standardweiß nach DIN 5033).
Die minimale Distanz (= y) für die Hintergrundausblendung kann aus dem Diagramm
[vgl. H15] wie folgt abgelesen werden:
Beispiel: x = 1000 mm, y = 20 mm. D. h. der Hintergrund wird ab einer Distanz von >
20 mm vom Objekt ausgeblendet.
PRODUKTBESCHREIBUNG 10
8020032.ZX33 | SICK
Subject to change without notice
19
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127

SICK PowerProx Small Analog - WTT190L-Axxxx Mode d'emploi

SICK
Marque
SICK
Modèle
PowerProx Small Analog - WTT190L-Axxxx
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents