Hestan KWCR24OV Guide d'installation

INDOOR PRESERVATION

Refrigerators, Freezers and Wine Storage

KRP / KRB / KRC / KFC / KWC / KRW

Installation Manual

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY

BEFORE INSTALLING OR USING YOUR APPLIANCE TO REDUCE

THE RISK OF FIRE, BURN HAZARD, OR OTHER INJURY. KEEP

THIS MANUAL FOR FUTURE REFERENCE.

Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of

this or any other appliance.

Installation and service must be performed by a qualiﬁed installer or service agency.

DO NOT REPAIR, REPLACE OR REMOVE ANY PART OF THE APPLIANCE UNLESS

SPECIFICALLY RECOMMENDED IN THE MANUAL. IMPROPER INSTALLATION,

SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER

TO THIS MANUAL FOR GUIDANCE. ALL OTHER SERVICING SHOULD BE DONE BY A

QUALIFIED TECHNICIAN.

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.

HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY, OR DEATH.

EN

SAFETY DEFINITIONS

DANGER. THIS INDICATES INFORMATION AND WARNINGS WHICH,

IF NOT OBSERVED, MAY COMPROMISE PERSONAL SAFETY OR DAMAGE

THE APPLIANCE.

DANGER OF ELECTROCUTION. THIS INDICATES INFORMATION AND

WARNINGS OF AN ELECTRICAL NATURE WHICH, IF NOT OBSERVED,

MAY COMPROMISE PERSONAL SAFETY OR DAMAGE THE APPLIANCE.

THIS HIGHLIGHTS GENERAL INFORMATION AND WARNINGS AND

INDICATES THAT DAMAGE TO THE APPLIANCE OR PROPERTY MAY

OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

TABLE OF CONTENTS

EN

1

When properly cared for, your Hestan appliance will provide safe, reliable service for many

years. When using this appliance, basic safety practices must be followed as outlined below.

IMPORTANT: Save these instructions for the local Utility Inspector’s use.

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these Installation Instructions for future reference.

This appliance is NOT designed for installation in manufactured (mobile) homes or

recreational park trailers. Do NOT install this appliance outdoors.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Failure to do

so can result in death or electrical shock.

ELECTRICAL GROUNDING

• This appliance must be grounded. Grounding reduces the risk of electric shock in the

event of a short circuit. Read the ELECTRICAL and WATER CONNECTIONS sections

of this manual for complete instructions.

• DO NOT ground to a gas pipe.

• DO NOT use an extension cord with this appliance.

• DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A fuse in the NEUTRAL

or GROUNDING circuit could result in an electrical shock.

1 SAFETY PRECAUTIONS - BEFORE YOU BEGIN

2 MODEL NUMBERS

3

RATING LABEL

3 REGULATORY / CODE REQUIREMENTS

4 IMPORTANT CHILD SAFETY

4

LOCATION AND INSTALLATION

29 REQUIRED VENTILATION

30

TESTING AND INITIAL START-UP

REFRIGERATION MODELS

FREEZER MODELS

Model No.

Description

MODEL NUMBERS

2

KRPR36 Bottom Mount Refrigerator, Top Compressor, Pro, Right Hinged, 36"

KRPL36 Bottom Mount Refrigerator, Top Compressor, Pro, Left Hinged, 36"

KRPR36-XX Bottom Mount Refrigerator, Top Compressor, Pro, Color, Right Hinged, 36"

KRPL36-XX Bottom Mount Refrigerator, Top Compressor, Pro, Color, Left Hinged, 36"

KRBR36 Bottom Mount Refrigerator, Bottom Compressor, Right Hinged, 36"

KRBL36 Bottom Mount Refrigerator, Bottom Compressor, Left Hinged, 36"

KRBR36-OV Bottom Mount Refrigerator, Bottom Compressor, Overlay, Right Hinged, 36"

KRBL36-OV Bottom Mount Refrigerator, Bottom Compressor, Overlay, Left Hinged, 36"

KRBR36-XX Bottom Mount Refrigerator, Bottom Compressor, Color, Right Hinged, 36"

KRBL36-XX Bottom Mount Refrigerator, Bottom Compressor, Color, Left Hinged, 36"

KRCR24 Refrigerator Column, Right Hinged, 24"

KRCL24 Refrigerator Column, Left Hinged, 24"

KRCR24-OV Refrigerator Column, Overlay, Right Hinged, 24"

KRCL24-OV Refrigerator Column, Overlay, Left Hinged, 24"

KRCR24-XX Refrigerator Column, Color, Right Hinged, 24"

KRCL24-XX Refrigerator Column, Color, Left Hinged, 24"

KRCR30 Refrigerator Column, Right Hinged, 30"

KRCL30 Refrigerator Column, Left Hinged, 30"

KRCR30-OV Refrigerator Column, Overlay, Right Hinged, 30"

KRCL30-OV Refrigerator Column, Overlay, Left Hinged, 30"

KRCR30-XX Refrigerator Column, Color, Right Hinged, 30"

KRCL30-XX Refrigerator Column, Color, Left Hinged, 30"

KFCR24 Freezer Column, Right Hinged, 24"

KFCL24 Freezer Column, Left Hinged, 24"

KFCR24-OV Freezer Column, Overlay, Right Hinged, 24"

KFCL24-OV Freezer Column, Overlay, Left Hinged, 24"

KFCR24-XX Freezer Column, Color, Right Hinged, 24"

KFCL24-XX Freezer Column, Color, Left Hinged, 24"

KFCR30 Freezer Column, Right Hinged, 30"

KFCL30 Freezer Column, Left Hinged, 30"

KFCR30-OV Freezer Column, Overlay, Right Hinged, 30"

KFCL30-OV Freezer Column, Overlay, Left Hinged, 30"

KFCR30-XX Freezer Column, Color, Right Hinged, 30"

KFCL30-XX Freezer Column, Color, Left Hinged, 30"

EN

3

Hestan appliance such as the model and serial number and

electrical rating.

The rating label is located on the inside wall of the refrigerator.

TYPICAL RATING LABEL

RATING LABEL

MODEL NUMBERS

The rating label contains important information about your

REGULATORY / CODE REQUIREMENTS

Installation of this appliance must be made in accordance with local codes. In the

absence of local codes, this unit should be installed in accordance with the National Electrical

Code and local codes.

This appliance must be electrically grounded in accordance with local codes or in the absence

of local codes with the National Electrical Code

ANSI/NFPA 70

, or Canadian Electrical code

CSA C22.1

.

WINE MODELS

Model No. Description

(continued)

NOTE: -XX indicates color model.

-BK for Stealth - Black

-YW for Sol - Yellow

-PP for Lush - Purple

-GG for Paciﬁc Fog - Graphite Gray

-WH for Froth - White

-OR for Citra - Orange

-BU for Prince - Blue

-RD for Matador - Red

-BG for Tin Roof - Burgundy

-GR for Grove - Green

-TQ for Bora Bora - Turquoise

KWCR24 Wine Column, Right Hinged, 24"

KWCL24 Wine Column, Left Hinged, 24"

KWCR24-OV Wine Column, Overlay, Right Hinged, 24"

KWCL24-OV Wine Column, Overlay, Left Hinged, 24"

KWCR24-XX Wine Column, Color, Right Hinged, 24"

KWCL24-XX Wine Column, Color, Left Hinged, 24"

KRWR24 Refrigerator with Wine, Right Hinged, 24"

KRWL24 Refrigerator with Wine, Left Hinged, 24"

KRWR24-OV Refrigerator with Wine, Overlay, Right Hinged, 24"

KRWL24-OV Refrigerator with Wine, Overlay, Left Hinged, 24"

KRWR24-XX Refrigerator with Wine, Color, Right Hinged, 24"

KRWL24-XX Refrigerator with Wine, Color, Left Hinged, 24"

ozFridge Gas Fill Charge

Quantité de Gaz Réfrigerateur

Freezer Gas Fill Charge

Quantité de Gaz Congélateur

Total Absorbed Current

Courant Absorbée Totale

Voltage

Tension

Frequency

Frequence

Refrigerant Gas Type

Type de Gaz Rèfrigerant

MODEL

Made in Italy

CODE

SER.NO./N° SERIE

3186660

ETL LISTED

CONFORMS TO

ANSI/UL STD 250

CERTIFIED TO CAN/CSA

STD C22.2 NO.63

A

V

Hz

HESTAN COMMERCIAL CORP.

ANAHEIM, CA - USA

KRP36

7

0

1

115

60

R134a

FI24RC-RO

XXXXXXXXXXX

EN

PREPARATION

IMPORTANT CHILD SAFETY

LOCATION AND INSTALLATION

4

DANGER: Risk of child entrapment. Before you throw away your old

refrigerator or freezer:

• Take off the doors

• Leave the shelves in place so that children may not easily climb

inside.

w: 650 mm (25 5/8”) h: 2260 mm (89”) d: 800 mm (31 1/2”)

w: 800 mm (31 1/2”) h: 2260 mm (89”) d: 800 mm (31 1/2”)

230 kg (507 lb)

30” Models

36” Models

275 kg (606 lb)

w: 950 mm (37 3/8”) h: 2260 mm (89”) d: 800 mm (31 1/2”)

295 kg (650 lb)

PACKAGED DIMENSIONS AND WEIGHTS

ELECTRICAL AND WATER SUPPLY

PROVIDED INSTALLATION ACCESSORIES

TOOLS

Before moving the refrigerator, protect any ﬁnished ﬂooring to prevent damage.

Make sure that power can be provided to the location selected.

24” Models

The following tools are needed for the installation of the dishwasher:

• Phillips screw driver

• Drill and drill bits

• 3/4” open-end or adjustable wrench

• 1/2” wrench or socket

The following pages provide the necessary information for proper installation of the refrigerator

and are arranged as follows:

• Technical data.

• Installation cutout dimensions, required clearances and mounting instructions.

• Electrical requirements and connections.

• Initial power-up and testing.

STEPS FOR INSTALLATION

110V 60Hz 15a

From 7.3 TO 73 PSI

3/4” female attachment

Customized panel mounting kit (included with -OV models only)

Anti-tip kit

Lateral/side connecting kit

4 mm (1/8”) allen wrench

Electrical requirement:

Potable water supply pressure:

Water supply tube:

EN

5

INSTALLATION CUT-OUT FEATURES - KRP MODELS

(continued)

min 10 (3⁄8”)

min 50 (2”)

2134 mm (84”)

900 mm (35 1/2”)

1470 mm (57 7/8”)

105°

899 mm (35 3/8”)

2120 mm (83 1/2”) + 25 mm (1”)

635 mm (25”)

900 (35 ½”)

A A

min 2134 (84”)

140 (5 ½”) 140 (5 ½”)

100 (4”)

560 (22”)

2120 (83 ½”) +25 (1”)

613 (24 1⁄8”)+25 (1”)

635 (25”)

97 (3 7/8”)

693 (27 ¼”)

516 (20

3/8”

)

1296 (50”)

195 (7

5⁄8”)

8 (3⁄8”)

1016 (40”)

1470 (57 7⁄8”

)

230 (9”)

560 (22”)

75 (3”)

899 (35 3/8”)

10 (3⁄8”)58 (2 ¼”)

105°

635 (25”)

Flush

IMPORTANT

Cut-out Height

Cut-out Width

Door Swing Clearance

Door Opening Angle

Width

Height

Depth with door

A Area to be left clear for the anti-tip brackets

LOCATION AND INSTALLATION

EN

6

INSTALLATION CUT-OUT FEATURES - KRB MODELS

140 (5 ½”) 140 (5 ½”)

100 (4”)

A A

min 2134 (84”)

900 (35

½”)

A

2134 mm (84”)

105°

2120 mm (83 1/2”) + 25 mm (1”)

610 mm (

24”)

610 (24”)

560 (22”)

1293 (50 7⁄8” )

474 (18 5⁄8” )

231 (9

1⁄8”

) +

25 (1”)

500 (19 )¾”

248 (9

¾”

)

+ 25 (1”)

20 ( )¾”

721 (28 3⁄8”) +25 (1”)

2120 (83 ½”) +25 (1”)

992 (39”)

FI36: 1470 (57 7⁄8”)

160 (6 3⁄8”)

560 (22”)

610 (24”)

899 (35 3⁄8”)

10 (3⁄8”)

105°

Area to be left clear for the anti-tip brackets

Cut-out Height

Cut-out Width

Door Swing Clearance

Door Opening Angle

Width

Height

Depth with door (without panel)

(continued)

LOCATION AND INSTALLATION

900 mm (35 1/2”)

1470 mm (57 7/8”)

899 mm (35 3/8”)

EN

7

INSTALLATION CUT-OUT FEATURES - KRP MODELS

Door Opening Angle

A Area to be left clear for the anti-tip brackets

(continued)

LOCATION AND INSTALLATION

2134 mm (84”)

30”: 750 mm (29 5/8”)

24”: 600 mm (23 3/4”)

30” : 1325 mm (52 1/8”)

24” : 1175 mm (46 1/4”)

105°

30”: 749 mm (29 1/2”)

24”: 599 mm (23 5/8”)

2120 mm (83 1/2”) + 25 mm (1”)

615 mm (

24 1/4”)

Cut-out Height

Cut-out Width

Door Swing Clearance

Width

Height

Depth with door (without panel)

24” AND 30” COLUMN REFRIGERATORS AND FREEZERS

24” WINE COLUMN AND 24” REFRIGERATOR WITH WINE

140 (5 ½”) 140 (5 ½”)

100 (4”)

A A

min 2134 (84”)

24”: 600 (23 ¾”)

30”: 750 (29 5⁄8”)

615 (24 1/4”)

560 (22 1/4”)

1808 (71 )¼”

231 (9

1⁄8”

) +

25 (1”)

505 (19 ¾”)

233 (9

¼”

)

+ 25 (1”)

2120 (83 ½”) +25 (1”)

30”: 1325 (52 1/8”)

24”: 1175 (46 1/4”)

30”: 53 (2 1⁄8”)

24”: 27 (1 1⁄16”)

560 (22 1/4”)

615 (24” 1/4)

30”: 761 (30”)

24”: 609 (24”)

10 (3⁄8”)

105°

EN

8

PREPARING THE INSTALLATION

(continued)

LOCATION AND INSTALLATION

To remove the front xing bracket

Remove the xing brackets

.

truck, remove the appliance and place it on the oor.

Be very careful to avoid any damage to oors. Delicate oors should be

1

4

1

2

3

Transport to installation site

and unpacking

Since this is a large and heavy appliance, before transporting the ap-

pliance, check the access to the location where it will be installed

(door size, maneuvering space in stairwells, etc.).

The appliance is attached to the base of the packaging (pallet) through

four bolts which can be removed using a 17 mm (3/4”) wrench.

It is recommended to use a manual transporting device to move the

appliance to the installation site, and only at this point to remove the

base of the packaging.

The appliance should always be transported in a vertical position.

If this is not possible, transport the appliance laying on its rear side.

Once at the installation site, the appliance, which is equipped with four

wheels, can be taken off the pallet and positioned in the installation

area.

Operate as follows:

Take off the four bolts

1

securing the appliance to the pallet by

means of a 17 mm (3/4”) wrench.

3

and

4

3

, unscrew for one or two turns

the rear wheel adjusting bolt

2

by means of a 13 mm (1/2”) wrench.

From the back of the unit and by means of a suitable, high duty hand

protected with plywood, hard cardboard or similar material panels.

The appliance is very heavy.

Take maximum care during handling to

avoid injury.

The appliance should always be transported

in a vertical position.

Avoid at all costs leaning it on its front side.

EN

9

CUT-OUT DIMENSIONS AND INSTALLATION METHODS - FLUSH

CUT-OUT DIMENSIONS AND INSTALLATION METHODS - NON-FLUSH

(continued)

LOCATION AND INSTALLATION

KRB36 Models

30” Columns

24” Columns and Wine

A A

B

A A

KRB36 Models

30” Columns

24” Columns and Wine

897 (35 1/4”)900 (35 1/2”)

750 (29 5/8”)

600 (23 3/4”)

747 (29 3/8”)

597 (23 1/2”)

Panel Width

Cut-out

Models

24”: 600 (23 ¾”)

30”: 750 (29 5⁄8”)

36”: 900 (35 ½”)

A Lateral/side connection kit (included accessory)

B

Central connection kit, required when joining 2 units)

900 (35 1/2”)

750 (29 5/8”)

600 (23 3/4”)

914 (36”

)

762

(30”)

610 (24”)

MAXMIN

Cut-outModels

24: 610 (24”)

30: 762 (30”)

36: 914 (36”)

A Lateral/side connection kit

A

6,5 (¼”)

A

6,5 (¼”

10 (3/8”

)

EN

AKRLJK

(for KRB, KRC, KFC, KWC and KRW Models)

AKRLJKP (for KRP Models)

(not included - must be ordered as a separate accessory)

AKRCJK (for KRB, KRC, KFC, KWC and KRW Models)

AKRCJKP (for KRP Models)

10

ELECTRICAL AND WATER CONNECTION

(continued)

LOCATION AND INSTALLATION

E

W

E

W

E

W

E

W

E

W

E

W

The appliances are delivered from the factory for operation at 110V-

120V AC - 60Hz (US and Canada).

They are provided with a suitable supply cable and plug to be con-

nected to an appropriate 15A socket (US and Canada) provided

with an effective grounding.

A circuit breaker should also be installed and should be easily ac-

cessible so that it can be easily switched off before performing any

installation or maintenance.

To connect to the water supply system (for appliances equipped with

ice makers) a 1/4” waterline with accessible shut-off valve must be

supplied.

The appliance is provided with a water adapter elbow which is suit-

able for high water pressure and complies the Food Regulations.

The water lter cartridge , which is provided with the appliance

should be installed according to the accompanying instructions. Use

only the new adapter which is supplied with the appliance. The so-

lenoid connection on the appliance is 3/4” diameter but is metric

threaded. A standard garden hose threaded connector such as a

braided stainless hose found at typical hardware stores will strip or

damage the solenoid threads. Use only the supplied 1/4” quick con-

nect elbow adapter for connecting a 1/4” copper or polyethylene

source water line to the appliance.

Electrical cord length: 2000 mm (78 3/4”)

Water connection line length: 2500 mm (98 3/8”)

Do not use extension cords and/or multiple adapters for the power

supply connection.

The appliance should be connected only to

a drinkable water supply system.

to drink any water which is not suitable for

human consumption.

Electrical and water supply behind the unit

Do not use extension cords or adapters.

Once the appliance is fully installed, con-

nected to the water supply (if applicable) and

operational, in the event that the water sup-

ply must be turned off,(touch the button

on

control panel to switch it off) before the main

water is shut off to prevent the appliance from

entering a ‘NO WATER IN’ alarm state.

The built-in Hestan lter cannot make it safe

KRP Models

All other Models

EN

11

(continued)

LOCATION AND INSTALLATION

ELECTRICAL AND WATER CONNECTION

(continued)

Back of appliance

Water connection

Electrical connection

Operate as follows:

Unwind the electric cable and connect it directly to the wall socket.

Make sure the appliance is in the Stand-by condition and that all

lights are off; if not, press the Unit button

to switch it off.

Push the 1/4” source waterline fully into the elbow connector then

thread the elbow adapter to the solenoid at the back of the appli-

ance.

to make a proper seal. Turn on the water and ensure all connections

are not leaking prior to pushing the unit into the niche.

Firmly tighted with ngers - a tool or wrench should not be needed

2

1

Operate as follows:

Unwind the electric cable and connect it directly to the wall socket.

Make sure the appliance is in the Stand-by condition and that all lights

are off; if not, press the Unit button to switch it off.

Connect the water line to the threaded connection at the base of the

1

Fit the other end of the hose to the water tap, use the gaskets provided

in the Owner’s Kit.

2

make a proper seal. Turn on the water and ensure all connections are

not leaking prior to pushing the unit into the opening.

Front of appliance

Back of appliance

Water connectionElectrical connection

unit.

Firmly tighten with ngers - a tool/wrench should not be needed to

KRP MODELS

ALL OTHER MODELS

EN

LEVELING THE REFRIGERATOR

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT

(continued)

LOCATION AND INSTALLATION

1

2

1

2

Adjust the appliance level by means of the front leveling feet

and the rear adjustable wheels.

Operate as follows:

After removing the bottom plinth or grill (it is kept in position by

magnets), adjust the height of the leveling feet

1

by means of a 17

mm (3/4”) open-end or adjustable wrench.

Then adjust the height of the rear wheels by turning the front

adjusting bolts

2

clockwise or counter-clockwise as required.

Reinstall the bottom plinth or grill.

1

2

3

Decorative door and bottom-drawer panels layout:

The dimensions of the panels are indicated in the table and draw-

ings on pages 18-19.

Nevertheless, according to the requirements for aligning with other

kitchen structures, the door panel can be higher than the upper

edge of the refrigerator door, and the drawer panel can be lower

than the edge of the drawer.

The panels must be mounted using special braces which attach

to adjustable devices provided on the door and drawer and with

brackets that anchor and adjust the panel’s vertical direction.

Braces, brackets and xing screws are provided with the appliance

and must be applied to the panel as indicated.

Operate as follows:

To prepare the panels to be mounted on the appliance, follow

these steps, working on the back of the panel.

Door Panel

Trace, a line dividing the panel width in half.

1

Starting from the bottom edge of the panel, mark the positioning

of the brackets.

2

Following the corresponding table, mark the external and then

the internal hole.

3

OVERLAY MODELS (-OV)

12

EN

13

(continued)

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT

7

8

4

5

Position the brackets on each set of marks to make sure they are

aligned

4

, then drill holes through the panel (pay close attention to

the panel’s thickness)

5

Screw the brackets in place

6

Drawer Panel

When preparing the Drawer Panel, follow the same instructions as

per the door panel, but make sure measurements are taken starting

from the top edge.

7

The support bracket faces the opposite way

8

(note images 4 and 8).

OVERLAY MODELS (-OV)

EN

6

(continued)

LOCATION AND INSTALLATION

D E

A

B C

F G

13 (½”)

13 (

½”)

34 (1

3/8”)

34 (1

3⁄8)”

1285 (50 5⁄8”)

1163 (45

¾”)

660 (26”)

157 (6

¼”)

min 1390 (54

¾”)max 635 (25”)

507.5 (20”)

382 (15

1⁄8”)

100 (4”)

A

897 (35 ¼”) 897 (35 ¼”)

355.5 (14”)

261 (10 ¼”)

418 (16 ½”)

386 (15 ¼”)

B

C

D

E

354.5 (14”) 354.5 (14”)

F / G

KRB36-OV

Hinge Right

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT

OVERLAY MODELS (-OV)

HOLE POSITIONS

Hinge Left

PANEL DIMENSIONS

14

15

(continued)

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT

OVERLAY MODELS (-OV)

KRWR24-OV MODELS

897 (35 ¼”) 897 (35 ¼”)

354.5 (14”) 354.5 (14”)

412 (16 ¼”)

380 (15”)

418 (16 ½”)

386 (15 ¼”)

A

D

E

F / G

H

I

Hinge Left

Hinge Right

H I

D E

A

F G

1286 (50 5⁄8”)

1152,5 (45 3⁄8”)

650,5 (25

5⁄8”)

148,5 (5

7⁄8”)

6,5 (¼”)

6,5 (

¼”)

13 (

½”)

34 (1

3⁄8)”

34 (1

3⁄8)”

min 1390 (54 ¾”)

max 635 (25”)

507,5 (20”)

382 (15

1⁄8”)

100 (4”)

24”: 327 (12

7⁄8” )

1075 (42 3⁄8” )

<200 (7 7⁄8”)

115 (4

½”)

135 (5 3⁄8”)

135 (5

3⁄8”)

HOLE POSITIONS

PANEL / FRAME DIMENSIONS

EN

(continued)

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT

OVERLAY MODELS (-OV)

HOLE POSITIONS

PANEL DIMENSIONS

A

747 (29 3⁄8)”

343 (13 ½”)

597 (23 ½”) 597 (23 ½”)

276,5 (10 7⁄8)”

268 (10 ½”)

B

C

Hinge Left

Hinge Right

30” -OV Column Models

24”-OV Column Models

747 (29 3⁄8)”

343 (13 ½”)

Hinge Left

Hinge Right

1

13 (½”)

1797 (70 ¾”)

B C

A

34 (1 3⁄8” 34 (1 3⁄8)”

165 (6 ½”)

1271,5 (50”)

690,5 (27

¼”)

112 (4 3⁄8”)

min 1933 (76

1⁄8”)

16

EN

17

(continued)

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT

OVERLAY MODELS (-OV)

HOLE POSITIONS

FRAME DIMENSIONS

597 (23 ½”) 597 (23 ½”)

276,5 (10 7⁄8)”

268 (10 ½”)

A

B

C

Hinge Left

Hinge Right

KWCR/L24-OV MODELS

1

13 (½”)

B C

A

34 (1 3⁄8” 34 (1 3⁄8)”

1797 (70 ¾”)

165 (6

½”)

1271,5 (50”)

690,5 (27

¼”)

112 (4

3⁄8”)

min 1933 (76

1⁄8”)

1572 (62”)

24: 327 (12 7⁄8” )

135 (5

3⁄8” )135 (5 3⁄8” )

min 200

(7

7⁄8”)

EN

(continued)

LOCATION AND INSTALLATION

(continued)

DOOR AND BOTTOM-DRAWER OVERLAY PANEL LAYOUT

OVERLAY MODELS (-OV)

PANEL DIMENSIONS - KRBR/L36-OV AND KRWR/L24-OV MODELS

Panels can have thickness ranging between 18 mm (3/4”) and 28 mm (1-1/8“).

Door panels can have a maximum weight 23 kg (51 lbs) and drawer panels may be a maximum

weight of 11kg (25 lbs).

Exceeding these weights could void your warranty for any service issues which can be

attributed to overweight panels.

The hinge mechanism on Hestan refrigerators is considered to be `Zero-clearance`. The door

and drawer widths specied below assume the minimum niche width is being used and a 3.5mm

(1/8”) reveal is desired around the panels. Adjust your panel dimensions accordingly to your own

design criteria considering your niche width and your reveal. Minimum reveal / gap should not be

less than 1.5mm (1/16”).

KRBR/L36-OV

KRWR/L24-OV

N/A

897 (35 1/4”)

327 (12 7/8”)597 (23 1/2”)

Door/Drawer Width

A

Models

Door Cutout Width

B

2121 (83 ½") + 25 (1")

min 540 (21 ¼”)

max 635 (25”)

A B

3 (1⁄8”)

1390 (54 ¾”)

115 (4 ½”)

min 200 (7 7⁄8”)

135

(5 3⁄8”)

135

(5 3⁄8”)

1075 (42 3⁄8”)

Example:

84” cut-out height

36” cut-out width

4” toe kick height

1/8” gap desired all around

Door panel:

Width: 35-3/4”

Height: 54-3/4”

Drawer panel:

Width: 35-3/4”

Height: 84”-1/8”-54-3/4”-1/8”-4”=25”

If you want a 6” toe kick height then your bottom drawer

panel height would be 23”

18

EN

La page est en cours de chargement...

Hestan KWCR24OV Guide d'installation

Hestan KWCR24OV Guide d'installation

dans d''autres langues

Documents connexes

Autres documents