Signature Kitchen Suite SKSCW241RP Guide d'installation

Marque: Signature Kitchen Suite

Modèle: SKSCW241RP

Taper: Guide d'installation

Integrated Refrigeration Installation Guide

BUILT-IN REFRIGERATION

SKSCF1801P

SKSCF2401P

SKSCF3001P

SKSCW181RP

SKSCR2401P

SKSCR3001P

SKSCW241RP

www.signaturekitchensuite.com

MFL67410824_Rev.07

ENGLISH FRANÇAIS ESPAÑOL

Table of Contents

SAFETY INSTRUCTIONS ............................. 3

Before Installation ......................................... 6

Choosing the Install Location ....................... 6

Installation options ....................................... 9

– Dimensions and Clearances

SKSCF1801P – 18" INTEGRATED

FREEZER COLUMN

SKSCW181RP – 18" INTEGRATED

WINE COLUMN .......................................... 10

SKSCF2401P – 24" INTEGRATED

FREEZER COLUMN

SKSCR2401P – 24" INTEGRATED

REFRIGERATOR COLUMN

SKSCW241RP – 24" INTEGRATED

WINE COLUMN .......................................... 12

SKSCF3001P – 30" INTEGRATED

FREEZER COLUMN

SKSCR3001P – 30" INTEGRATED

REFRIGERATOR COLUMN ....................... 14

– Custom Panels

SKSCF1801P – 18" INTEGRATED

FREEZER COLUMN

SKSCW181RP – 18" INTEGRATED

WINE COLUMN .......................................... 16

SKSCF2401P – 24" INTEGRATED

FREEZER COLUMN

SKSCR2401P – 24" INTEGRATED

REFRIGERATOR COLUMN

SKSCW241RP – 24" INTEGRATED

WINE COLUMN ......................................... 18

SKSCF3001P – 30" INTEGRATED

FREEZER COLUMN

SKSCR3001P – 30" INTEGRATED

REFRIGERATOR COLUMN ....................... 20

Required Accessories and Tools ................ 22

Installation .................................................. 23

Unpacking ...................................................... 24

Moving the Appliance .................................... 25

Special Circumstances .................................. 25

Product Dimensions ...................................... 26

Installing the Anti-tip Brackets ....................... 29

Protecting Edges of Enclosure ..................... 30

Installing Appliance in Enclosure .................. 31

Aligning and Leveling the Appliance ............. 32

Attaching the Appliance to the Enclosure ...... 34

Attaching the Toe Kick Panel ........................ 35

Installing Door Panels .................................. 37

Adjusting Door Panels .................................. 38

Installing Door Trim ...................................... 38

Attaching Air Separator ................................. 39

– Special Installations

Optional Frame Kit Accessory ...................... 39

Adjusting the Door Spring ............................ 40

Adjusting the Door Stop ............................... 40

Water Filter Bypass ...................................... 40

Reversing the Door ...................................... 41

Side-by-Side Flush Installation ..................... 45

Preparing to Connect the Water Line ............ 47

Connecting the Water Line ........................... 47

Attaching the Badge ..................................... 48

ENGLISH

SAFETY INSTRUCTIONS

WARNING

TIP-OVER HAZARD

Use two or more people to move and install the refrigerator.

To prevent the refrigerator from tipping over, install anti-tip brackets

(provided). Failure to follow the refrigerator installation instructions

can result in serious injury or death.

WARNING You may be killed or seriously injured if you don’t follow instructions.

WARNING To reduce the risk of fire, electric shock, or personal injury when using

the product, basic safety precautions should be followed, including the

following. Read all instructions before using this appliance.

CAUTION Indicates an imminently hazardous situation which, if not avoided, may

result in minor or moderate injury, or product damage.

IMPORTANT SAFETY INSTRUCTIONS

This guide contains many important safety messages.

Always read and obey all safety messages.

This is the safety alert symbol. It alerts you to safety messages that inform you of hazards

that can kill or hurt you or others or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard signal word

WARNING, or CAUTION. These words mean:

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and

tell you what can happen if the instructions are not followed.

Installation

• These products are not designed to be used as freestanding units. Doing so will result in a

risk of tipover, personal injury, and product or property damage.

• Do not install the refrigerator near a gas stove, water heater or other source of ignition that

may possibly leak gas. Do not install product in direct sunlight. Install the product in a well-

ventilated area.

• Ensure that enclosure dimensions allow for sufficient air circulation at the sides and back of

the product. Do not block the front air inlet. Failure to follow these instructions may cause

product malfunction.

• Enclosure must be constructed of materials which are strong enough to avoid damage

during installation and frequent use.

• Cabinet materials must be able to withstand the heat and humidity produced during product

operation and use without twisting or deforming.

• Install the product on a firm, level surface that can support the weight of the product without

bending. The product must be level both horizontally and vertically.

• Keep children away from area during installation.

• Do not use an extension cord or power strip with this product.

• Do not install the refrigerator in a damp location or where it will be exposed to running water.

Deterioration of the insulation on electrical parts may result, causing risk of electric shock.

• Connect to potable water only. Non-potable water can cause health risks.

• If connected to a circuit protected by fuses, use time delay fuse.

Electrical Connection

Use a dedicated outlet.

• Plugging several devices into one outlet may cause a fire.

Plug in the power plug with the power cord facing downward.

Failure to do so could damage the plug or cord, resulting in fire or electric shock.

When installing or moving the refrigerator, be careful not to roll over or damage the

power cord. Do not squeeze or crush the cord or plug when pushing the refrigerator in.

Doing so could result in fire or electric shock.

Do not allow the power cord to be bent, crushed, or damaged. Do not run the power

cord under heavy objects like furniture, other appliances, or through high-traffic areas.

Doing so may damage the power cord and result in fire or electric shock.

Do not extend or modify the length of the power cord.

Use only an exact factory replacement part to avoid electrical issues, fire, or electric shock.

Turn off the power before cleaning or moving the refrigerator.

• Failure to do so may cause electric shock or injury.

• Press the POWER button for 3 seconds to turn off the power at display panel.

Do not pull out the cord or touch the power plug with wet hands.

Doing so may cause electric shock or injury.

Remove water or dust from the power plug and insert it securely into the wall socket.

Dust, water, or a loose connection may cause a fire or electric shock.

Do not unplug the refrigerator by pulling on the cord.

Doing so may cause electric shock or short circuit resulting in a fire.

Do not use the power cord or the power plug if it is damaged or if the outlet is damaged.

Doing so may cause electric shock or short circuit resulting in a fire.

Wait for 5 minutes or longer when reconnecting the plug or turning the power back on.

Give the compressor time to cycle before restarting.

ENGLISH

General

These installation instructions are intended for use by qualified installers. All connections for water,

electrical power and grounding must comply with local codes and ordinances and be made by

licensed personnel when required. In the absence of a local code:

•

In the U.S.A., in accordance with the National Electric Code, ANSI/NFPA70 – latest edition/State

and Municipal codes and/or local codes.

•

In Canada, in accordance with the Canadian Electric Code C22.1 – latest edition/Provincial and

Municipal codes and/or local codes.

Appliance is very heavy:

Refrigerator 30" approx. 386 Ibs/175 kg

Refrigerator 24" approx. 324 Ibs/147 kg

Freezer 30" approx. 403 Ibs/183 kg

Freezer 24" approx. 346 Ibs/157 kg

Freezer 18" approx. 304 Ibs/138 kg

Wine 18" approx. 306 lbs/139 kg

Wine 24" approx. 357 lbs/162 kg

CAUTION

Do not remove the cover of the automatic ice dispenser.

The internal mechanism of the icemaker can cause injury if handled.

Do not stick your hands under the refrigerator.

Sharp edges, fans, and wires may cause an injury

Save these instructions for the local inspector's use.

Observe all governing codes and ordinances.

Installer: Leave these instructions with the consumer.

Consumer: Keep these instructions with the owner's manual for future reference.

If the supply cord is damaged, it must be replaced by the manufacturer or its service

agent or a similarly qualified person in order to avoid a hazard.

Before Installation

Choosing the Install Location

Anti-tip Devices

WARNING

Do not store or install the appliance where it will be exposed to:

• outside weather

• water damage

• temperatures under 32°F (0°C)

Temperature and Humidity

The appliance should be installed in a dry, well ventilated area.

The ambient temperature should stay between 55 °F(13 °C) and 110 °F (43 °C), to avoid

malfunctions.

Do not install product where it will be exposed to direct sunlight or near a heat source, such as an

oven or radiator.

WARNING: Tip Hazard

• The appliance is very heavy and may tip over if the door is opened before the appliance is

securely installed.

• Install the supplied anti-tip brackets to prevent the appliance from tipping. The safest method of

installing the appliance in a stable position is to use the supplied anti-tip devices.

• Do not open the appliance door unless it is still on the pallet or the anti-tip brackets are engaged.

If the enclosure is sturdy enough, attaching the appliance to the upper and side walls of the

enclosure may provide additional stability, as long as the enclosure is firmly connected to the back

wall. If in doubt, contact an architect or structural engineer.

ENGLISH

Enclosure

Floor

• The panel above the appliance must be made from a solid material (not MDF) that is at

least 5/8" (16 mm) thick.

• The side walls of the cavity or enclosure must be flush.

• The front 4 inches (100 mm) of the interior surface (furniture return) will be visible when

doors are open. Make sure this area is finished to at least 4 inches deep.

• Follow the specifications for the installation enclosure to ensure a trouble free installation.

• Above all, the enclosure cannot be out of square. Use a spirit level or measure the

diagonals of the opening to make sure corners are square.

• The appliance is attached at the sides and the top to either the enclosure or to adjacent

cabinets. Make sure the enclosure or the adjacent cabinets are securely connected to the

floor or wall structures.

WARNING

• The floor in the installation area must be firm, level, and rigid for safe installation and best

performance.

• Do not install the appliance on a platform or raised structure.

• The structure underneath the appliance must be able to support the weight of the appliance

without tilting or flexing.

• For best performance and to avoid leakage, level the appliance.

Electrical Requirements

WARNING

Electrical Shock Hazard

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Follow all state and local codes or NEC.

The appliance comes with a UL listed 3 wire power supply cord.

The appliance requires a 3-wire receptacle.

The receptacle must be installed by a licensed electrician only.

Grounding

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will

reduce the risk of electric shock by providing a path of least resistance for the electric current.

WARNING: Improper connection of the equipment grounding conductor may result in electric

shock. Have the appliance checked by a qualified electrician or service technician

if you are in doubt as to whether the appliance has been properly grounded.

NOTE

Some local regulations may require a separate ground. In such cases, the required ground

wire, clamp and screw are available as a separate accessory and must be purchased

separately.

Never ground the appliance to plastic plumbing lines, gas lines or water pipes.

Water Connection

CAUTION

• Connect the appliance to potable water only.

• A cold water connection is required for operation of the automatic ice maker. The water pressure

must be between 20 and 120 psi. (1.38-8.27).

• The installation must comply with local plumbing regulations.

• A separate shut-off valve must be installed for the appliance water connection.

• Do not use a self-piercing valve.

• Do not install the shutoff valve for the water behind the appliance. The shutoff valve must be

easily accessible.

• Install the water connection in the area shown in the diagram under Dimensions and Clearances.

The water supply line can be located on the right side, on the left side, or in the floor. The

maximum outer diameter of the supply line (without fittings) is 3/8" (9.5 mm).

ENGLISH

Installation options

There are many different installation options.

These are limited only by the design of the kitchen.

Individual Appliance

OK OK X

Side-by-Side (Pair)

OK X X X

Individual Appliances with Partition

Minimum thickness of the partition 5/8” (16 mm)

1 1/4" (32 mm) 7 7/8" (200 mm)

**25/32” (20 mm)

*1 9/16” (40 mm)

**25/32” (20 mm)

*1 9/16” (40 mm)

**25/32” (20 mm)

*1 9/16” (40 mm)

OK OK

A A A

* When not using 90° door stop pin

** When using 90° door stop pin on the A product

SKSCF1801P – 18" INTEGRATED FREEZER COLUMN

SKSCW181RP – 18" INTEGRATED WINE COLUMN

NOTE

Freezer/Wine column can be installed ush or proud.

Flush – With a 25" (635 mm) cutout depth, the front face of the freezer/wine column ts ush with 25"

(635 mm) depth adjacent cabinets.

Proud – With a 24" (610 mm) depth cutout, the front face of the freezer/wine column extends

approximately 3/4" (19 mm) beyond 24" (610 mm) depth adjacent cabinets.

• A minimum 4" (102 mm) nished return that matches the cabinet exterior is recommended on all

sides and the top of the cutout opening. The shaded area will be visible after installation.

ELECTRICAL

A 115V, 60Hz, 15 or 20 amp power supply is required. An individual, properly grounded branch

circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical

receptacle recessed into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

WATER LINE

A cold water supply is required for automatic icemaker operation.

The water pressure must be between 20 and 120 psi.

Tubing should be long enough to extend to the front of the freezer. Allow enough tubing to

accommodate a bend leading into the water line connection.

Water line can enter an opening through the oor or back wall.

Install a shut-o valve between the icemaker water valve and the cold water supply in the home.

CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION, SINGLE COLUMN

1 3/8" (35mm)

Electrical location

Is Not available

1 3/8" (35mm)

Electrical location

Is Not available

18" (457 mm)

84"

(2134 mm)

(127 mm)

electrical

location

(102 mm)

water

location

(102 mm)

finished

return*

25"(635 mm)

min. depth

flush install

24" (610 mm)

min. depth

proud install

finished width

ENGLISH

NOTE

Door Swing Clearances

The installation must allow for clearances to adjacent walls or cabinets. This freezer/wine column is

equipped with a 2-position door stop.

The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is

restricted.

Door Handle Clearances

The door handle depth must be added to the dimension where noted to determine the total

clearance required from adjacent cabinets or walls. This clearance will vary depending on the custom

handle used. When using Signature Kitchen Suite handles or the Signature Kitchen Suite stainless

steel door panel kit with handles (optional accessories), the door handle clearance with the door

open 115° is 11" (279 mm).

INSTALLATION CLEARANCES

TOP VIEW

90°

115°

8 3/4"*

(223 mm

)

24"

(610 mm)

20 1/4"

(514 mm)

18"

17 3/4"

(451 mm)

3/4"

(19 mm)**

** Varies depending on the

thickness of the custom

cabinet panel. The door panels in

the optional Signature Kitchen Suite

stainless steel door panel kit are

3/4" (19 mm) thick.

Door handle must be added

to this dimension.

(457 mm)

1/8"

(3mm)

min.

1/8"

(3mm)

min.

90°

115°

8 3/4"*

(223 mm)

24"

(610 mm)

20 1/4"

(514 mm)

18"

17 3/4"

(451 mm)

(457 mm)

1/8"

(3mm)

min.

1/8"

(3mm)

min.

SKSCF1801P SKSCW181RP

SKSCF2401P – 24" INTEGRATED FREEZER COLUMN

SKSCR2401P – 24" INTEGRATED REFRIGERATOR COLUMN

SKSCW241RP – 24" INTEGRATED WINE COLUMN

NOTE

Freezer/Wine / Refrigerator column can be installed ush or proud

Flush – With a 25" (635 mm) cutout depth, the front face of the freezer/wine column ts ush with 25"

(635 mm) depth adjacent cabinets.

Proud – With a 24" (610 mm) depth cutout, the front face of the freezer/wine column extends

approximately 3/4" (19 mm) beyond 24" (610 mm) depth adjacent cabinets.

• A minimum 4" (102 mm) nished return that matches the cabinet e terior is recommended on all

sides and the top of the cutout opening. The shaded area will be visible after installation.

ELECTRICAL

A 115V, 60Hz, 15 or 20 amp power supply is required. An individual, properly grounded branch

circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical

receptacle recessed into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

WATER LINE

A cold water supply is required for automatic icemaker operation.

The water pressure must be between 20 and 120 psi.

Tubing should be long enough to extend to the front of the freezer. Allow enough tubing to

accommodate a bend leading into the water line connection.

Water line can enter an opening through the oor or back wall

Install a shut-o valve between the icemaker water valve and the cold water supply in the home.

CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION, SINGLE COLUMN

24" (610 mm)

finished width

84"

(2134 mm)

(127 mm)

electrical

location

(102 mm)

water

location

1 3/8" (35mm)

Electrical location

Is Not available

1 3/8" (35mm)

Electrical location

Is Not available

(102 mm)

finished

return*

25"(635 mm)

min. depth

flush install

24" (610 mm)

min. depth

proud install

ENGLISH

NOTE

Door Swing Clearances

• The installation must allow for clearances to adjacent walls or cabinets. The appliances are

equipped with 2-position door stops.

• The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is

restricted.

Door Handle Clearances

The door handle depth must be added to the dimension where noted to determine the total clearance

required from adjacent cabinets or walls. This clearance will vary depending on the custom handle

used. When using Signature Kitchen Suite handles or the Signature Kitchen Suite stainless steel

door panel kit with handles (optional accessories), the door handle clearance with the door open

115° is 14" (356 mm).

INSTALLATION CLEARANCES

TOP VIEW

11 3/8"* 11 3/8"*

610

24 610

** Varies depending on the

thickness of the custom

cabinet panel. The door panels in

the optional Signature Kitchen Suite

stainless steel door panel kit are

3/4" (19 mm) thick.

Door handle must be added

to this dimension.

SKSCF2401P SKSCR2401P

SKSCW241RP

SKSCF3001P – 30" INTEGRATED FREEZER COLUMN

SKSCR3001P – 30" INTEGRATED REFRIGERATOR COLUMN

NOTE

Freezer / Refrigerator can be installed flush or proud.

Flush – With a 25" (635 mm) cutout depth, the front face of the refrigerator fits flush with 25" (635

mm) depth adjacent cabinets.

Proud – With a 24" (610 mm) depth cutout, the front face of the refrigerator extends approximately

3/4" (19 mm) beyond 24" (610 mm) depth adjacent cabinets.

* A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all

sides and the top of the cutout opening. The shaded area will be visible after installation.

ELECTRICAL

A 115V, 60Hz, 15 or 20 amp power supply is required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical

receptacle recessed into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

WATER LINE

The water pressure must be between 20 and 120 psi.

Tubing should be long enough to extend to the front of the refrigerator. Allow enough tubing to

accommodate a bend leading into the water line connection.

Water line can enter an opening through the floor or back wall.

Install a shut-off valve between the water valve and cold water supply in the home.

CUTOUT DIMENSIONS – FLUSH OR PROUD INSTALLATION, SINGLE COLUMN

30" (762 mm)

finished width

84"

(2134 mm)

(127 mm)

electrical

location

(102 mm)

water

location

1 3/8" (35mm)

Electrical location

Is Not available

1 3/8" (35mm)

Electrical location

Is Not available

(102 mm)

finished

return*

25"(635 mm)

min. depth

flush install

24" (610 mm)

min. depth

proud install

ENGLISH

NOTE

Door Swing Clearances

The installation must allow for clearances to adjacent walls or cabinets. This freezer / refrigerator

is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if

clearance to adjacent cabinets or walls is restricted.

Door Handle Clearances

The door handle depth must be added to the dimension where noted to determine the total

clearances required from adjacent cabinets or walls. This clearance will vary depending on the

custom handle used. When using Signature Kitchen Suite handles or the Signature Kitchen Suite

stainless steel door panel kit with handles (optional accessories), the door handle clearance with the

door open 115° is 16" (406 mm).

INSTALLATION CLEARANCES

TOP VIEW

3/4"

(19 mm)**

** Varies depending on the

thickness of the custom

cabinet panel. The door panels in the optional

Signature Kitchen Suite stainless steel door

panel kit are 3/4" (19 mm) thick.

Door handle must be added

to this dimension.

SKSCF3001P SKSCR3001P

SKSCF1801P – 18" INTEGRATED FREEZER COLUMN

SKSCW181RP – 18" INTEGRATED WINE COLUMN

3/4" (19 MM) CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION

Door Panel

(451 mm)

17 3/4"

47 3/4" (1213 mm)

(756 mm)

29 3/4"

DUAL 18" AND 30" COLUMN

Door Panel Door Panel 79 7/8"

(2029 mm)

79 7/8"

(2029 mm)

(451 mm)

17 3/4"

41 3/4" (1060 mm)

(603 mm)

23 3/4"

DUAL 18” AND 24” COLUMN

Door Panel Door Panel 79 7/8"

(2029 mm)

(451 mm)

17 3/4"

SINGLE COLUMN

Door

Panel

(451 mm)

17 3/4"

47 3/4" (1213 mm)

(756 mm)

29 3/4"

DUAL 18" AND 30" COLUMN

Door Panel 79 7/8"

(2029 mm)

79 7/8"

(2029 mm)

(451 mm)

17 3/4"

41 3/4" (1060 mm)

(603 mm)

23 3/4"

DUAL 18” AND 24” COLUMN

Door Panel 79 7/8"

(2029 mm)

(451 mm)

17 3/4"

SINGLE COLUMN

Door

Panel

Door

Panel

(179.5 mm)

7 1/16

(80.5 mm)

3 3/16

(238 mm)

9 3/8

Freezer/Refrigerator Column

Wine Column

ENGLISH

NOTES

Trimmed units are designed to be customized with decorative panels. Field-installed 3/4" (19 mm)

custom door panels are required.

For custom panels: Use templates provided with units to pre-drill holes for mounting panel brackets

(provided with unit). Adjustment screws and instructions also provided with units.

Maximum total door panel weight for 30" column is 64 lb.

Maximum total door panel weight for 24" column is 53 lb.

Maximum total door panel weight for 18" column is 44 lb.

DESIGN TIPS

4" (102 mm) will be visible on the interior sides of the cutout. It is recommended that the

interior of the enclosure be nished to match the exterior. For retrot/replacement installations,

the optional frame kit may be used.

If using custom panels, a custom toe kick is required.

The bottom of the case is unnished.

Door Handles: Handles are not included with the units.

Custom handles are required for installation. Brushed aluminum handles are available as an optional

accessory.

SKSPK180CS/SKSPK185CS – STAINLESS STEEL PANEL

KIT FOR 18" FREEZER COLUMN

SKSWK185RS/SKSWK185LS – STAINLESS STEEL PANEL

KIT FOR 18” WINE COLUMN

This unit can be installed with an optional stainless steel

panel kit. The freezer column kit is reversible and can be

used in both right hand and left hand door swing installations.

The wine column panel kits are not reversible.

SKSFK800CS – FRAME KIT

This unit can be installed in a 24" (610 mm) deep cutout with

an optional frame kit. The kit includes two 80" (2032 mm)

brushed aluminum side trim pieces. Each trim piece is 5"

(127 mm) deep with a 1/8" (3 mm) front face.

HANDLES FOR USE WITH CUSTOM PANELS

SKSHK310HS – 31 11/16" (805 mm) Medium Brushed

Aluminum Handle

SKSHK480HS – 48" (1219 mm) Long Brushed Aluminum

Handle

DESIGN TIPS

The stainless steel panel kit may be used in a ush 25" (635

mm) cutout depth installation or in a proud 24" (610 mm)

cutout depth installation.

The optional frame kit is recommended for retrot/

replacement installations where the existing cutout is 24"

(610 mm) deep.

OPTIONAL ACCESSORIES – FLUSH OR PROUD INSTALLATION

SKSPK180CS

SKSPK185CS

SKSWK185LS SKSWK185RS

Finishing of the handle has been

chaged from glossy to matte since April,

2022. When pair-installing a product,

• Please identify the production date on

the panel installation box.

• Match the production date of the

handles into before April 2022 or after

April 2022.

WARNING

SKSCF2401P – 24" INTEGRATED FREEZER COLUMN

SKSCR2401P – 24" INTEGRATED REFRIGERATOR COLUMN

SKSCW241RP – 24" INTEGRATED WINE COLUMN

3/4" (19 MM) CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION

(603 mm)

23 3/4"

53 3/4" (1365 mm)

(756 mm)

29 3/4"

DUAL 24" AND 30" COLUMN

Door Panel 79 7/8"

(2029 mm)

79 7/8"

(2029 mm)

47 3/4" (1213 mm)

(603 mm)

23 3/4"

DUAL 24” AND 24” COLUMN

Door Panel 79 7/8"

(2029 mm)

(603 mm)

23 3/4"

Door Panel

(603 mm)

23 3/4"

Door Panel

(603 mm)

23 3/4"

Door Panel

SINGLE COLUMN

(603 mm)

23 3/4"

53 3/4" (1365 mm)

(756 mm)

29 3/4"

DUAL 24" AND 30" COLUMN

Door Panel

79 7/8"

(2029 mm)

79 7/8"

(2029 mm)

47 3/4" (1213 mm)

(603 mm)

23 3/4"

DUAL 24” AND 24” COLUMN

Door Panel

79 7/8"

(2029 mm)

(603 mm)

23 3/4"

Door Panel

(603 mm)

23 3/4"

Door Panel

(603 mm)

23 3/4"

Door Panel

SINGLE COLUMN

(179.5 mm)

7 1/16"

(80.5 mm)

3 3/16"

(238 mm)

9 3/8"

Freezer/Refrigerator Column

Wine Column

ENGLISH

NOTES

Trimmed units are designed to be customized with decorative panels. Field-installed 3/4" (19 mm)

custom door panels are required.

For custom panels: Use templates provided with units to pre-drill holes for mounting panel brackets

(provided with unit). Adjustment screws and instructions also provided with units.

Maximum total door panel weight for 30" column is 64 lb.

Maximum total door panel weight for 24" column is 53 lb.

Maximum total door panel weight for 18" column is 44 lb.

DESIGN TIPS

4" (102 mm) will be visible on the interior sides of the cutout. It is recommended that the

interior of the enclosure be nished to match the exterior. For retrot/replacement installations,

the optional frame kit may be used.

If using custom panels, a custom toe kick is required.

The bottom of the case is unnished.

Door Handles: Handles are not included with the units.

Custom handles are required for installation. Brushed aluminum handles are available as an optional

accessory.

SKSPK240CS/SKSPK245CS – STAINLESS STEEL PANEL

KIT FOR 24" FREEZER / REFRIGERATOR COLUMN

SKSWK245RS/SKSWK245LS – STAINLESS STEEL PANEL

KIT FOR 24" WINE COLUMN

This unit can be installed with an optional stainless steel

panel kit. The freezer/refrigerator column kit is reversible

and can be used in both right hand and left hand door swing

installations. The wine column panel kits are not reversible.

SKSFK800CS – FRAME KIT

This unit can be installed in a 24" (610 mm) deep cutout with

an optional frame kit. The kit includes two 80" (2032 mm)

brushed aluminum side trim pieces. Each trim piece is 5"

(127 mm) deep with a 1/8" (3 mm) front face.

HANDLES FOR USE WITH CUSTOM PANELS

SKSHK310HS – 31 11/16" (805 mm) Medium Brushed

Aluminum Handle

SKSHK480HS – 48" (1219 mm) Long Brushed Aluminum

Handle

DESIGN TIPS

The stainless steel panel kit may be used in a ush 25" (635

mm) cutout depth installation or in a proud 24" (610 mm)

cutout depth installation.

The optional frame kit is recommended for retrot/

replacement installations where the existing cutout is 24"

(610 mm) deep.

OPTIONAL ACCESSORIES – FLUSH OR PROUD INSTALLATION

SKSPK240CS

SKSPK245CS

SKSWK245LS SKSWK245RS

Finishing of the handle has been

chaged from glossy to matte since April,

2022. When pair-installing a product,

• Please identify the production date on

the panel installation box.

• Match the production date of the

handles into before April 2022 or after

April 2022.

WARNING

SKSCF3001P – 30" INTEGRATED FREEZER COLUMN

SKSCR3001P – 30" INTEGRATED REFRIGERATOR COLUMN

NOTES

Trimmed units are designed to be customized with decorative panels. Field-installed 3/4" (19 mm)

custom door panels are required.

For custom panels: Use templates provided with units to pre-drill holes for mounting panel brackets

(provided with unit). Adjustment screws and instructions also provided with units.

Maximum total door panel weight for 30" column is 64 lb.

Maximum total door panel weight for 24" column is 53 lb.

Maximum total door panel weight for 18" column is 44 lb.

DESIGN TIPS

4" (102 mm) will be visible on the interior sides of the cutout. It is recommended that the interior

of the enclosure be finished to match the exterior. For retrofit/replacement installations, the

optional frame kit may be used.

If using custom panels, a custom toe kick is required. The bottom of the case is unfinished.

Door Handles: Handles are not included with the units. Custom handles are required for installation.

Brushed aluminum handles are available as an optional accessory.

3/4" (19 MM) CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION

Door Panel

(756 mm)

29 3/4" 59 3/4" (1518 mm)

(756 mm)

29 3/4"

DUAL 30" AND 30" COLUMN

Door Panel 79 7/8"

(2029 mm)

79 7/8"

(2029 mm)

(756 mm)

29 3/4"

Door Panel

SINGLE COLUMN

La page charge ...

Signature Kitchen Suite SKSCW241RP Guide d'installation

Marque: Signature Kitchen Suite

Modèle: SKSCW241RP

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Signature Kitchen Suite SKSCW241RP Installation guide
español: Signature Kitchen Suite SKSCW241RP Guía de instalación

Signature Kitchen Suite SKSCW241RP Guide d'installation

Signature Kitchen Suite SKSCW241RP Guide d'installation

dans d''autres langues

Autres documents