NOTE
Make sure the supplied rechargeable battery with the
label THIS SIDE UP facing up.
3 Align the battery compartment cover flat
against the battery compartment, then
place down and slide it towards the center
of the parent unit until it clicks into place.
User’s manual
VM311/VM311-13/VM311-2/
VM311-23
Safe & SoundTM
Full Color Video and Audio
Monitor
Congratulations
on purchasing your new VTech product.
Before using this product, please read
Important safety instructions.
For support, shopping, and everything new at
VTech, visit our website at
www.vtechphones.com.
Register online to get an additional
3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for
enhanced warranty support.
Product news
Learn about the latest VTech
products.
BC
You can power up the parent unit by connecting
it to AC power or to the rechargeable battery
provided. Even if the parent unit is connected
to AC power, we recommend you also
install the battery. This guarantees continual
operation in case of a power outage.
Install the battery as shown below.
Slide and lift to open the battery compartment
cover.
Plug the battery connector securely into
the socket.
1.
2.
Install the battery
Replace the battery
To replace the battery, pull the battery out of
the battery compartment and unplug the battery
connector from the socket, then follow the steps
above to install the battery.
NOTES
The operating time for using the rechargeable
battery is short. If you want to monitor your baby
for a long time, we recommend you connect the
parent unit to AC power.
If the parent unit will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
NOTES
Use only the battery supplied with this product.
Use only the parent unit power adapter or the baby
unit power adapter supplied with this product.
The parent unit power adapter and baby unit
power adapter are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
Make sure the parent unit, the baby unit and the
power adapter cord are out of reach of children.
•
•
•
•
•
•
Connect and charge the
battery
Connect the baby unit
Connect the parent unit
Power outlet not controlled
by a wall switch
Parent unit power adapter
Self-adhesive
strap
Charge the parent unit battery
Once you have connected the parent unit and
installed its battery, press and hold to turn it
on. The battery icon indicates the battery status
(see the following table).
NOTES
The parent unit battery is fully charged after
12 hours of continuous charging.
It takes longer to charge the battery when the
parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
The standby time varies depending on the
sensitivity level you set, your actual use, and the
age of the battery.
Battery
indicators
Battery
status
Action
The battery
icon is off and
displays.
No battery
is installed
but operates
using AC
power, or the
battery has
been installed
incorrectly.
Install the
parent unit
battery.
Charge
without
interruption
(at least 30
minutes).
The screen
displays .
The light
flashes.
The battery
has very little
charge and
may be used
for only a
short time.
Charge
without
interruption
(about 30
minutes).
The battery
icon becomes
solid .
The battery is
fully charged.
To keep
the battery
charged,
connect it to
AC power
when not in
use.
•
•
•
You may test the baby monitor before initial
use, and at regular times thereafter.
To test your video and audio monitor:
Place the parent unit and the baby units in
the same room to test the product. Make
sure the baby units are at least 3 feet away
from the parent unit.
Press and hold on the baby units until
the POWER light turns on.
Press and hold on the parent unit until
the POWER light turns on.
NOTE
If both units are not connected, the parent unit
displays while searching for a baby unit. If no baby
unit is found after a while,
it displays .
Positioning the baby monitor
Place the parent unit within the operating range
of the baby unit. We recommend the parent
unit is at least 3 feet away from the baby unit
to avoid audio feedback. If you still experience
audio feedback, move the parent unit and the
baby unit farther apart.
NOTE
For better image quality, do not place the baby unit too
far away from your baby.
TIP
For desktop usage and/or wall mounting the baby
unit, you can refer to Installation guide.
Operating range
The operating range of the baby monitor is up
to 1,000 feet outdoors or 150 feet indoors. The
actual operating range may vary depending
on the environmental conditions and other
interferences such as walls, doors and other
obstructions.
1.
2.
3.
Before use
Baby unit overview
1Camera
2Infrared LEDs
Backup light for night vision.
3POWER on/off indicator
On when the baby unit is powered on
and currently linked to parent unit.
Flashes when the baby unit is not
linked to a parent unit; or
the pairing process is in progress; or
the parent unit is not viewing this baby
unit.
•
•
4Power jack
5Control key panel
/VOL+
Press to increase the listening volume.
/VOL
-
Press to decrease the listening volume.
PAIR
Press and hold to pair to the parent unit.
(On/Off)
Press and hold to turn on or off.
6Microphone
7Stand
Tilt to adjust the camera angle.
8Rim
9Base
Parent unit overview
1Visual sound indicator
The visual sound indicator has two
functions. One is to show the sound level
detected by the baby unit. The other
one is to show the volume level during
speaker volume setting.
Sound level detected by the baby unit
One to three green
lights indicate a moderate sound level
detected by the baby unit.
Additional red
lights indicate a higher sound level
detected by the baby unit (e.g. baby
crying loudly).
Speaker volume level
One to three green
lights indicate Level 1 to Level 3 of
the speaker volume setting.
Additional red
lights indicate Level 4 to Level 5 of
the speaker volume setting.
•
•
•
•
2 Battery level indicator
Light On when the parent unit battery
is being charged.
Light Flashes when the parent unit
battery is low and needs charging.
Light Off when the parent unit battery
is fully charged, or when no battery is
installed.
•
•
•
3POWER on/off indicator
On when the parent unit is turned on.
Flashes when in pairing process, or
when connecting to baby unit while
the baby unit is not available.
•
•
4Power jack
Overview
5Control key panel
/VOL+
Press to increase the speaker volume.
While in the menu, press to scroll up.
While viewing a zoomed image,
press and hold to move the image
upward.
MENU/SELECT
Press to enter the menu.
While in a menu, press to choose an
item, or save a setting.
/VOL
-
Press to decrease the speaker volume.
While in the menu, press to scroll
down.
While viewing a zoomed image,
press and hold to move the image
downward.
/
While in a menu, press to choose the
option on the left side.
While viewing a zoomed image, press
to zoom out; or
press and hold to move the image
leftward.
/
While in a menu, press to choose the
option on the right side.
While viewing image, press to zoom in.
While viewing a zoomed image,
press and hold to move the image
rightward.
TALK
While viewing image, press and hold to
talk to the selected baby unit.
(On/off)
Press and hold to turn on or off.
Press to turn on or off the screen.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
6Slot for portable use
7Stand
8Battery compartment cover
r
Baby unit
Power outlet not
controlled by a wall switch
Baby unit power adapter
Self-adhesive
strap
Parts checklist
THIS SIDE UP
1 set for
VM311/VM311-13;
2 sets for
VM311-2/VM311-23
Power on or off the baby unit
Press and hold to turn on the baby unit.
The POWER light turns on.
Press and hold again to turn off the baby
unit. The POWER light turns off.
Power on or off the parent unit
Press and hold to turn on the parent unit.
The screen turns on.
Press and hold again to turn off the
parent unit. The screen turns off.
Turn on or off the parent unit screen
If you want to hear sound from baby unit without
watching the screen, you can choose to turn off
the screen to save power. You can turn it back on
later when necessary.
Press on the parent unit at any time.
Adjust the speaker volume for
baby unit
You can adjust the speaker volume.
Press /VOL+ or /VOL
-
on the baby unit
at any time.
Adjust the speaker volume for
parent unit
You can adjust the speaker volume from
Volume 1 to Volume 5, or turn it off.
Press /VOL+ or /VOL
-
on the parent
unit when it is not in use.
When the speaker volume is set to off, the
screen displays .
Adjust the LCD brightness of the
parent unit
You can adjust the brightness of the parent
unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
Press MENU/SELECT when the parent unit is
not in use.
•
•
•
•
•
•
•
1.
Parent unit display icons
Connection status
- displays when strong signal
strength is detected between the
baby unit and the parent unit.
- , or displays when moderate
signal strength is detected between
the baby unit and the parent unit.
- displays when the link between the
baby unit and the parent unit is lost.
- displays when the parent unit is
searching for a baby unit.
x
(x:1-4)
Current view status
- Display the number of the baby unit
that is being viewed.
Zoom
- Display when the camera at the
baby unit has zoomed in.
Volume off
- Display when the volume is turned off.
Sound activation
- Display when the sound activation
is on. The parent unit screen
automatically goes on when the
baby unit detects a sound in the
baby room.
Battery status
- animates
when the battery is charging.
- displays solid when the battery is
fully charged.
- displays when the battery is low
and needs charging.
- displays when no battery is installed
but operates using AC power, or the
battery has been installed incorrectly.
Parent unit main menu icons
Camera selection
You can select the screen to view
images from a particular baby unit,
or view all baby units in Patrol Mode.
•
Brightness
You can change the brightness of
the screen.
•
Sensitivity
You can use the parent unit to adjust
the microphone sensitivity of the
baby unit. The higher the sensitivity
level, the more sounds it detects in
your baby’s room.
•
Using the baby monitor
Sound activation
Automatically turns on the parent unit
screen when a sound is detected in
your baby’s room. When no sound is
detected, the screen is off to save power.
•
Pairing
The baby units and parent unit
provided are already paired. You can
add or replace baby units (VM310/
VM310-13 purchased separately) to
your baby monitor system.
•
TIP
Depending on surroundings and other interference
factors, like a night light being too close to the baby
unit or white furniture blocking the view, the display
resolution may vary. Place the baby unit at a higher
level to prevent glare and blurry display.
Pair and replace extra new baby
unit (VM310/VM310-13)
The baby units and parent unit provided are
already paired. You can add or replace any baby
units (VM310/VM310-13 purchased separately)
to your video and audio monitor system.
NOTE
You can pair a maximum of four baby units to your
parent unit. Each new baby unit must be paired to the
parent unit before use.
To pair and replace a baby unit:
Press MENU/SELECT when the parent unit is
not in use.
Press or to choose .
Press or to choose a desired baby unit
slot, then press MENU/SELECT. The screen
displays .
NOTE
If you choose an occupied baby unit slot, the new
baby unit will replace the existing baby unit.
4. Turn on the new baby unit, and then
immediately press and hold PAIR until the
POWER light turns on.
When pairing is successful, the screen displays
, and then the image from the newly paired
baby unit.
NOTES
If pairing fails, the screen displays . Try the
pairing process again.
Only one baby unit can be paired at a time.
To unpair a baby unit:
NOTE
Make sure you power on the baby unit and the parent
unit before unpairing the baby unit.
Press MENU/SELECT when the parent unit
is not in use.
Press or to scroll to .
Press or to select the desired baby unit
(1, 2, 3 or 4).
Press and hold TALK until and display.
Press or to select to cancel, or to
confirm the unpair process.
Press MENU/SELECT to confirm your selection.
When unpairing is successful, the POWER
light on the selected baby unit flashes. The
parent unit displays for a while, and then the
image from the baby unit previously viewing.
1.
2.
3.
•
•
1.
2.
3.
4.
5.
6.
Press or to scroll to .
Press or to adjust the brightness.
Press MENU/SELECT to confirm your selection.
Adjust the sound sensitivity of the
baby unit
You can use the parent unit to change the sound
sensitivity level of the baby units. The higher the
sound sensitive is set, the more sensitive the
baby unit is in detecting sounds for transmitting
to the parent unit.
Sound sensitivity table for reference
Icon display Sensitivity Description
The parent unit speaker
is constantly on, and
you will hear all sounds
from your baby’s room.
The parent unit speaker
turns on for soft babbling
and louder sounds from
your baby. It remains
quiet when your baby
sleeps soundly.
The parent unit speaker
turns on for loud babbling
and louder sounds from
your baby. It remains
quite when your baby
makes soft sounds.
The parent unit speaker
turns on for crying and
louder sounds from
your baby. It remains
quiet when your baby
makes soft sounds.
The parent unit speaker
turns on for loud crying
or screeching sounds
from your baby. It remains
quiet when your baby
makes soft sounds.
Press MENU/SELECT when the parent unit is
not in use.
Press or to scroll to .
Press or to adjust the sensitivity level.
Press MENU/SELECT to confirm your selection.
TIP
You can adjust the baby unit placement to improve
the sound detection.
Turn on or off the sound activation
The parent unit continuously monitors the sound
level in your baby’s room. When the sound
activation mode is on, the parent unit screen
turns on when the baby unit detects a sound.
2.
3.
4.
1.
2.
3.
4.
As long as no sound is detected within 50 seconds,
the parent unit screen is off to save power. When
your baby starts to cry, the sound activation triggers
the parent unit screen automatically turns on.
Press MENU/SELECT when the parent unit
is not in use.
Press or to scroll to .
Press or to select to turn on, or
to turn off sound activation.
Press MENU/SELECT to confirm your selection.
NOTES
If you mute the speaker while sound activation
is on, then you hear a beep sound whenever the
screen turns on.
If you want to turn on the parent unit screen
continuously while the sound activation is on,
then set the sound sensitivity to .
Select the camera
You can select the screen to view images from
a particular baby unit, or view all baby units in
Patrol Mode. If you select Patrol Mode to view
the images, the screen switches to view another
baby unit automatically after some time. The
switching is in chronological order: to .
Press MENU/SELECT when the parent unit is
not in use.
Press or to scroll to .
Press or to select the desired baby unit
(1, 2, 3 or 4) or Patrol Mode ( ).
Press MENU/SELECT to confirm your selection.
Zoom
You can zoom in or out while viewing image
from baby unit.
Press to zoom in.
Press and hold , , or to move the
zoomed image upward, downward, leftward
or rightward correspondingly.
Press to zoom out.
Talk function
You can use the TALK function of the parent
unit to talk and comfort your baby.
Press and hold TALK when the parent
unit is viewing particular baby unit. Speak
towards the microphone on the parent unit.
Your voice is broadcast to the baby unit.
Night vision
The baby unit has infrared LEDs that allow you
to see your baby clearly at night or in a dark room.
When the baby unit detects low light levels, the
infrared LEDs are switched on automatically.
NOTE
When the infrared LEDs are on, the image is in black
and white. This is normal due to external light sources.
1.
2.
3.
4.
•
•
1.
2.
3.
4.
•
•
•
•
High
sensitivity
Low
sensitivity
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase (“Consumer”
or “you”) that the Product and all accessories
provided in the sales package (“Product”) are
free from defects in material and workmanship,
pursuant to the following terms and conditions,
when installed and used normally and in accordance
with the Product operating instructions. This limited
warranty extends only to the Consumer for Products
purchased and used in the United States of America
and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s
authorized service representative will repair or
replace at VTech’s option, without charge, a
Materially Defective Product. If we repair the Product,
we may use new or refurbished replacement
parts. If we choose to replace the Product, we
may replace it with a new or refurbished Product
of the same or similar design. We will retain
defective parts, modules, or equipment. Repair or
replacement of the Product, at VTech’s option, is
your exclusive remedy. VTech will return the repaired
or replacement Products to you in working condition.
You should expect the repair or replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product
under the terms of this limited warranty, this limited
warranty also applies to the repaired or replacement
Product for a period of either (a) 90 days from the date
the repaired or replacement Product is shipped to
you or (b) the time remaining on the original one-year
warranty; whichever is longer.
Below are the questions most frequently asked about
the baby monitor. If you cannot find the answer to
your question, contact customer service by visiting our
website at www.vtechphones.com or calling
1 (800) 595-9511.
FCC Part 15
This equipment has been tested and found to comply
with the requirements for a Class B digital device
under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
The RBRC® seal on the nickel-metal battery indicates
that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and
recycle these batteries at the end of their useful lives,
when taken out of service within the United States
and Canada.
The RBRC® program provides a convenient
alternative to placing used nickel-metal batteries into
the trash or municipal waste, which may be illegal in
your area.
VTech’s participation in RBRC® makes it easy for
you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized
VTech product service centers. Please call
1 (800) 8 BATTERYTM for information on Ni-MH
battery recycling and disposal bans/restrictions in
your area. VTech’s involvement in this program is
part of its commitment to protecting our environment
and conserving natural resources.
RBRC® is a registered trademark of Rechargeable
Battery Recycling Corporation.
Frequently asked
questions
When you are not going to use the baby monitor for
some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and
the adapters in a cool and dry place.
Storage
Why does the
baby monitor not
respond normally?
Try the following (in the order
listed) for common cure:
1. Disconnect the power to
the baby units and the
parent unit.
2. Remove the batteries in the
parent unit. Then install the
batteries again.
3. Wait a few minutes before
connecting power back
to the baby units and the
parent unit.
4. Turn on the baby units and
the parent unit.
5. Wait for the parent unit
to synchronize with the
baby units. Allow up to one
minute for this to take place.
Why don’t the
power-on light of
the baby unit and
parent unit go on
when I switch on
the units?
Perhaps the rechargeable
battery of the parent unit is
empty and the parent unit is
not connected to the mains.
Insert the appliance plug
into the parent unit and put
the adapter in a wall socket.
Then press to switch on the
parent unit and to establish
connection with the baby unit.
Perhaps the baby unit is
not connected to the mains.
Connect the baby unit to the
mains. Then set ON/OFF
switch to ON to switch on the
baby unit and to establish
connection with the parent unit.
Why is my screen
in black and
white?
The screen is in black and
white during nighttime or in a
dark room. This is normal due
to external light sources.
Why does the
baby monitor
produce a high-
pitched noise?
The units may be too close
to each other. Make sure the
parent unit and the baby unit
at least 1 metre/3 feet away
from each other.
Why does the
parent unit react
too quickly to
other sounds?
The baby unit also detects
other sounds than those
of your baby. Adjust the
sensitivity level to a lower
level or adjust the speaker
volume on the parent unit.
The RBRC® seal
FCC and IC regulations
Limited warranty
What is not covered by this limited warranty?
This limited warranty does not cover:
Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or other
liquid intrusion; or
Product that has been damaged due to repair,
alteration or modification by anyone other than an
authorized service representative of VTech; or
Product to the extent that the problem experienced
is caused by signal conditions, network reliability,
or cable or antenna systems; or
Product to the extent that the problem is caused
by use with non-VTech accessories; or
Product whose warranty/quality stickers, product
serial number plates or electronic serial numbers
have been removed, altered or rendered illegible; or
Product purchased, used, serviced, or shipped for
repair from outside the United States of America
or Canada, or used for commercial or institutional
purposes (including but not limited to Products
used for rental purposes); or
Product returned without a valid proof of purchase
(see item 2 on the next page); or
Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.
How do you get warranty service?
NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume
the risk of loss or damage during transit and
transportation and are responsible for delivery or
handling charges incurred in the transport of the
Product(s) to the service location. VTech will return
repaired or replaced Product under this limited
warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for
damage or loss of the Product in transit. If the
Product failure is not covered by this limited warranty,
or proof of purchase does not meet the terms of
this limited warranty, VTech will notify you and will
request that you authorize the cost of repair prior
to any further repair activity. You must pay for the
cost of repair and return shipping costs for the repair
of Products that are not covered by this limited
warranty.
What must you return with the Product to get
warranty service?
Return the entire original package and
contents including the Product to the VTech
service location along with a description of the
malfunction or difficulty; and
Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product
model) and the date of purchase or receipt; and
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 2407.5 - 2475 MHz
Parent unit: 2407.5 - 2475 MHz
Channels 21
LCD 2” Color LCD
(QVGA 320x240 pixel)
Nominal
effective
range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirement
Parent unit: 3.6 V Ni-MH battery
Baby unit power adapter:
Input: 100-240V AC 150mA 50/60Hz
Output: 6V DC 600mA
Parent unit power adapter:
Input: 100-240V AC 150mA 50/60Hz
Output: 6V DC 600mA
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product. This
product has been tested and found to comply with
the FCC criteria. The baby unit shall be installed
and used such that parts of all persons’ body are
maintained at a distance of approximately
8 in (20 cm) or more.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device complies with Industry Canada licence-
exempt RSS standard(s).
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Privacy of communications may not be ensured when
using this product.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
This product meets the applicable Industry Canada
technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The baby unit should be installed and
operated with a minimum distance of 8 in (20 cm)
between the baby unit and all persons’ body. Use of
other accessories may not ensure compliance with
FCC RF exposure guidelines. This transmitter must
not be co-located or operating in conjunction with
any other antenna or transmitter. This equipment
complies also with Industry Canada RSS-102 with
respect to Canada’s Health Code 6 for Exposure of
Humans to RF Fields.
•
•
•
•
Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to
this Product. VTech provides no other warranties for
this Product. The warranty exclusively describes all
of VTech’s responsibilities regarding the Product.
There are no other express warranties. No one
is authorized to make modifications to this limited
warranty and you should not rely on any such
modification.
State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other rights,
which vary from state to state or province to province.
Limitations: Implied warranties, including those of
fitness for a particular purpose and merchantability
(an unwritten warranty that the Product is fit for
ordinary use) are limited to one year from the date
of purchase. Some states/provinces do not allow
limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. In no
event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages
(including, but not limited to lost profits or revenue,
inability to use the Product or other associated
equipment, the cost of substitute equipment, and
claims by third parties) resulting from the use of this
Product. Some states/provinces do not allow the
exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may
not apply to you.
Please retain your original sales receipt as proof
of purchase.
3. Technical specications
Specifications are subject to change without notice.
© 2014 VTech Communications, Inc.
All rights reserved. 08/14. VM311-X_CIB_V7.0
Document order number: 91-007629-040-100
This baby monitor meets the California Energy
Commission (CEC) regulations for energy consumption.
Your baby monitor is set up to comply with the
energy-conserving standards right out of the box.
Follow the instructions to install and charge the
battery. The CEC battery charging testing mode is
activated while charging.
Even if the parent unit is paired to baby units, the
CEC battery charging testing mode is activated while
it is powered off and charging.
California Energy Commission
battery charging testing mode
Mesures de sécurité importantes
Lorsque vous utilisez votre appareil, vous devriez
toujours suivre certaines mesures de précaution
de base afin de réduire les risques d’incendie,
d’électrocution et de blessures corporelles, dont
ceux qui suivent :
Observez toutes les instructions et mises en
garde inscrites sur l’appareil.
L’installation par un adulte est requise.
Ce produit a été conçu pour être un dispositif
d’appoint seulement. Il n’est pas le remplacement
d’une supervision responsable et adéquate par un
adulte et ne devrait pas être utilisé comme telle.
Ce produit n’est pas conçu pour être utilisé en
tant que moniteur médical.
N’utilisez pas cet appareil près de l’eau ni de toute
autre source d’humidité, par exemple, près d’une
baignoire, cuve à lessive, évier de cuisine, dans
un sous-sol humide ni près d’une piscine, dans un
soussol humide ou une douche.
MISE EN GARDE: Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de
piles pour l’unité du parent. N’utilisez que le
bloc-piles rechargeable inclus ou le bloc-piles de
rechange (BT185645/BT285645). N’incinérez pas
les piles. Celles-ci risqueraient d’exploser. Jetez
les piles usées selon les renseignements suivant
le sceau du RBRC®.
N’utilisez que les adaptateurs inclus avec ce
produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre
votre sécurité en péril.
Adaptateur de l’unité du bébé :
Entrée 100-240V CA 150mA 50/60 Hz;
Sortie : 6 V CC 600 mA
Adaptateur de l’unité du parent :
Entrée 100-240V CA 150mA 50/60 Hz;
Sortie : 6 V CC 600 mA
Lorsqu’ils sont branchés dans une prise de
courant, les adaptateurs secteur ont été conçus
pour être orientés correctement, soit à la
1.
2.
3.
4.
5.
6.
7.
8.
verticale ou au plancher. Les broches n’ont pas
été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici
est branché dans une prise au plafond, sous une
table ou dans un meuble.
Débranchez ce produit de la prise de courant
avant de procéder au nettoyage. N’utilisez pas de
nettoyants en aérosols. Utilisez un chiffon humide
pour le nettoyer.
Débranchez les cordons d’alimentation avant de
remplacer le bloc-piles.
Ne coupez pas les cordons d’alimentation pour
remplacer les fiches, car ceci peut présenter un
danger potentiel.
Ne laissez aucun objet reposer ni appuyer sur
le cordon d’alimentation. N’installez pas cet
appareil dans un endroit où l’on risque d’écraser
le cordon d’alimentation ou de le piétiner.
Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur l’étiquette. Si
vous ne connaissez pas le type d’alimentation
que vous possédez à votre domicile, consultez
votre marchand ou votre compagnie locale
d’électricité.
Ne surchargez pas les prises de courant murales
ni les rallonges électriques.
Ne placez pas cet appareil sur un chariot,
meuble, trépied, support de montage ni table
chancelants.
Les trous et ouvertures du boîtier, situés à
l’arrière de l’appareil ou sous celui-ci, servent à
aérer l’appareil. Pour l’empêcher de surchauffer,
ne bloquez sous aucun prétexte ces ouvertures
et n’empêchez pas l’aération adéquate de
l’appareil en le plaçant sur un lit, divan, tapis ou
toute autre surface similaire. De même, ne le
positionnez pas à proximité ni au-dessus d’une
source de chaleur ou d’un calorifère. De plus,
ne placez pas l’appareil dans un endroit avant
de vous assurer qu’il y ait une bonne circulation
d’air.
N’enfoncez jamais d’objets à travers les
ouvertures de cet appareil, car ils pourraient
entrer en contact avec des points de tension
dangereux ou causer des courts-circuits qui
peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide
dans ce produit.
Afin de réduire les risques d’électrocution, ne
démontez pas cet appareil, mais apportez-le
dans un centre de service autorisé. L’ouverture
du boîtier ou le retrait de toutes pièces que
contient cet appareil, à l’exception de l’accès
autorisé à certaines portes ou ouvertures,
risque de vous exposer à des points de tension
dangereux ou d’autres dangers. Un remontage
incorrect peut par la suite présenter des risques
d’électrocution.
Vous devriez tester la réception chaque fois que
vous mettez l’appareil en fonction.
Examinez les composantes afin de vérifier si
celles-ci ne sont pas endommagées.
Soyez avisé de la perte de la confidentialité
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
lorsque vous utilisez les ondes publiques. Les
conversations peuvent être entendues par
d’autres moniteurs de bébé, des téléphones
sans fil, des scanneurs, etc.
Les enfants devraient être supervisés afin de
vous assurer qu’ils ne jouent pas avec l’appareil.
Le produit n’est pas conçu pour être utilisé
par des personnes (incluant des enfants) aux
capacités physiques, sensorielles ou mentales
réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné
suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une
personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
Utilisez et entreposez le produit à une
température entre 0˚ C (32˚F) et 40˚C (104˚ F).
N’exposez pas cet appareil à des froids ou des
chaleurs extrêmes, ainsi qu’à la lumière directe
du soleil. Ne l’installez pas près d’une source de
chauffage.
Le bloc-piles ne doit pas être exposé à la chaleur
excessive telle que la lumière du soleil ou au feu.
Assurez-vous que le moniteur et le cordon
de l’adaptateur sont toujours hors de portée
des enfants, à au moins 1 mètre (3 pieds) de
l’enfant ou du berceau, pour éviter tout risque de
strangulation.
Ne jamais placer le moniteur à l’intérieur du
berceau ou du parc de bébé. Ne jamais couvrir
le moniteur ou l’unité (s) portative avec un article
tel une serviette ou une couverture.
D’autres équipements électroniques peuvent
produire des interférences sur votre moniteur
vidéo et audio. Tentez d’installer votre
moniteur vidéo ou audio à l’écart des appareils
électroniques tels que des routeurs sans fil,
radios, téléphones cellulaires, interphones,
moniteurs, téléphones, ordinateurs personnels,
électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux
dispositifs numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs
et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
Vous devriez maintenir les dispositifs sans fil à au
moins six pouces du simulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est
en marche.
22.
23.
1.
2.
3.
4.
5.
6.
•
•
For cETL compliance only
When using your equipment, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock and injury,
including the following:
Follow all warnings and instructions marked
on the product.
Adult setup is required.
This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
This product is not intended for use as a
medical monitor.
Do not use this product near water. For
example, do not use it next to a bath tub, wash
bowl, kitchen sink, laundry tub or swimming
pool, or in a wet basement or shower.
CAUTION: Use only the batteries indicated in
this manual. There may be a risk of explosion
if a wrong type of battery is used for the parent
unit. Use only the supplied rechargeable
battery or replacement battery pack
(BT185645/BT285645) for the parent unit. Do
not dispose of batteries in a fire. They may
explode. Dispose of used battery according to
the information in The RBRC® seal.
1.
2.
3.
4.
5.
6.
Use only the adapters included with this
product. Incorrect adapter polarity or voltage
can seriously damage the product.
Baby unit power adapter: Input 100-240V
AC 150mA 50/60Hz; Output: 6V DC 600mA
Parent unit power adapter: Input 100-240V
AC 150mA 50/60Hz; Output: 6V DC 600mA.
The power adapters are intended to be
correctly oriented in a vertical or floor mount
position. The prongs are not designed to
hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
Unplug this product from the wall outlet
before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
Unplug the power cords before replacing
batteries.
Do not cut off the power adapters to replace
them with other plugs, as this causes a
hazardous situation.
Do not allow anything to rest on the power
cords. Do not install this product where the
cords may be walked on or crimped.
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply in your home, consult your
dealer or local power company.
Do not overload wall outlets or use an
extension cord.
Do not place this product on an unstable
table, shelf, stand or other unstable surfaces.
This product should not be placed in
any area where proper ventilation is not
provided. Slots and openings in the back
or bottom of this product are provided
for ventilation. To protect them from
overheating, these openings must not be
blocked by placing the product on a soft
surface such as a bed, sofa or rug. This
product should never be placed near or over
a radiator or heat register.
Never push objects of any kind into this
product through the slots because they may
touch dangerous voltage points or create a
short circuit. Never spill liquid of any kind on
the product.
To reduce the risk of electric shock, do
not disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the product other than
specified access doors may expose you to
dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when
the product is subsequently used.
You should test the sound reception every
time you turn on the units or move one of
the components.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Important safety
instructions
Cautions
Use and store the product at a temperature
between 32oF and 104oF.
Do not expose the product to extreme
cold, heat or direct sunlight. Do not put the
product close to a heating source.
Batteries should not be exposed to
excessive heat such as bright sunshine
or fire.
Make sure the baby unit(s) and the adapter
cord(s) are always out of reach of the baby,
at least 3 feet away from the baby or crib, to
avoid a possible strangulation hazard.
Never place the baby unit(s) inside the
baby’s crib or playpen. Never cover the
baby unit(s) or parent unit with anything
such as a towel or a blanket.
Other electronic products may cause
interference with your baby monitor. Try
installing your baby monitor as far away
from these electronic devices as possible:
wireless routers, radios, cellular telephones,
intercoms, room monitors, televisions,
personal computers, kitchen appliances and
cordless telephones.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless devices):
Wireless Technology Research, LLC (WTR),
an independent research entity, led a
multidisciplinary evaluation of the interference
between portable wireless devices and
implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR
recommends to physicians that:
1.
2.
3.
4.
5.
6.
L’étude effectuée par l’organisme WRS n’a pas
identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent
dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes
les normes se rapportant aux champs
électromagnétiques (EMF) standard. Si vous le
manipulez correctement en suivant les instructions
de ce guide, son utilisation sera sécuritaire pendant
de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons
aujourd’hui.
NOTE
Sling is not included. You may need to buy a sling
for portable usage.
Make sure battery is installed and charged.
Unplug the power adaptor.
Pinch the end of the sling and insert it into
the slot on the top of the parent unit.
Insert the one end of the sling into the
other end of the sling, and fasten it.
1.
2.
3.
Portable use of parent unit
(optional)
To keep this product working well and looking good,
follow these guidelines:
Avoid putting it near heating appliances and
devices that generate electrical noise (for example,
motors or fluorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft cloth.
DO NOT immerse the parent unit and the baby
unit in water and do not clean them under the tap.
DO NOT use cleaning spray or liquid cleaners.
Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
•
•
•
•
•
•
•
General product care
Pacemaker patients
Should keep wireless devices at least six
inches from the pacemaker.
Should NOT place wireless devices directly
over the pacemaker, such as in a breast
pocket, when it is turned ON.
WTR’s evaluation did not identify any risk
to bystanders with pacemakers from other
persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards
regarding electromagnetic fields (EMF).
If handled properly and according to the
instructions in this user’s manual, the product
is safe to be used based on scientific evidence
available today.
•
•
Periodically examine all components for
damage.
Be aware of possible loss of privacy while
using public airwaves. Conversations may
be picked up by other nursery monitors,
cordless phones, scanners, etc.
Children should be supervised to ensure
that they do not play with the product.
The product is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
20.
21.
22.
23.
Why don’t I hear a
sound/Why can’t
I hear my baby
cry?
The volume of the parent unit
may have set too low. Press
/VOL+ to increase the
volume level.
You may have set a low
sound sensitivity level. See
Adjust the sound sensitivity
of the baby unit to change
the setting.
Why does the
parent unit beep? The baby units may be out of
range. Move the parent unit
closer to the baby units (but
not less than 3 feet).
If the parent unit is powered by
the provided battery, it may not
have enough charge for the
parent unit to perform normally.
Charge the battery in the
parent unit for up to 12 hours.
Why can’t I
establish a
connection? Why
is the connection
lost every now
and then? Why
are there sound
interruptions?
The baby units may be out of
range. Move the parent unit
closer to the baby units (but
not less than 3 feet).
Other electronic products may
cause interference with your
baby monitor. Try installing
your baby monitor as far away
from these electronic devices
as possible.
-
1
-
2
VTech VM311-13 Manuel utilisateur
- Catégorie
- Babyphones
- Taper
- Manuel utilisateur
dans d''autres langues
- English: VTech VM311-13 User manual
Documents connexes
-
VTech VM311 Manuel utilisateur
-
-
-
VTech VM981 Mode d'emploi
-
-
VTech VM3252 Manuel utilisateur
-
VTech VM320 Manuel utilisateur
-
-
-