©2022 VUPOINT SOLUTIONS, INC. All Rights Reserved.
The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint Solutions Inc. in the United States and
other countries. App Store is a registered trademark of Apple Inc. iOS is a registered trademark of Cisco Technology,
Inc. in the U.S. and other countries and is under license. Android and Google Play are registered trademarks of Google
LLC. Product names, logos, brands and other trademarks referred to herein are the property of their respective
trademark holders. All trademarks remain the property of their respective holders, and are used only to describe the
products or services being provided. These trademark holders are not affiliated with VuPoint Solutions, Inc. They do not
sponsor or endorse VuPoint Solutions, Inc’s products or services.
VuPoint Solutions, Inc. (USA):
710 Nogales Street, City of Industry, CA 91748
VuPoint (Europe) Company Limited:
1 Devon Way, Longbridge Technology Park,
Longbridge, Birmingham B31 2TS
facebook.com/toucansmarthome
Instagram.com/toucansmarthome
YouTube.com/c/toucansmarthome
For additional info, visit our website at ToucanSolution.com
Wall Anchors
Mounting Screws
Adhesive Tape
Warranty CardUser Manual Thank You Card
Charging Cable
Magnetic Base Mount
Magnetic Ball
Wireless Security Camera PRO
Items included
USER MANUAL
Wireless Security
Camera PRO
TSCP05GR
Regulations & Compliance
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
ISED Regulatory Compliance
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
RF Exposure Compliance
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux radiations FCC/IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur
et votre corps.contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le
radiateur et votre corps.
Microphone
Camera Lens
LED Indicator
Speaker
Radar Sensor
Toucan
Login
Email ID
Password
Create A New Account
SET button
Open the mirco USB plug cover,
plug in the micro USB cable to
charge the camera.
Recommend to fully charge the device
before 1st use.
Charge your Wireless Security Camera PRO
Setup your Wireless Security Camera PRO
Install your Wireless Security Camera PRO
Threaded screw hole
(for magnetic ball or
accessory secure mount)
RST button
Mirco USB plug
1Download the Toucan App
2Login to the App
4Connect your device
3Add your device
www.toucansolution.com/pages/toucan-smart-home-app
Available at Apple© App Store© and Google Play™
Scan QR code or visit
Open the app and
create a free account.
Follow the instructions in the
Toucan App to complete the setup
Tap the “+” to
add a device
1Check WiFi signal at installation area
2Attach the magnetic ball 3Mark the Magnetic Mount's preferred placement
4Choose how you want to secure the Magnetic Mount
ABC
5Place the camera on the Magnetic Mount
If using 3M Adhesive only (B), allow 24 to 48 hours curing time before placing the camera onto the
Magnetic Mount to ensure maximum bonding strength.
When using just the 3M adhesive (B) to install the Magnetic Mount, apply the adhesive on dry surfaces
only. It is suitable for UPVC, wooden or smooth surface door frames. (Not suitable for brick or stone)
*
**
Screw the magnetic ball onto
the back of the camera
Using the magnetic mount as a template,
mark where you want to mount the
camera with a pencil.
Take the camera to the planned
installation area. Tap on the
camera in the Toucan App
Dashboard to bring up Live View to
make sure there is good WiFi signal
at the installation area.
Place the camera with the ball onto the Magnetic Mount.
It will attach firmly. Adjust camera angle best suited.
For detailed setup procedure, please refer to
the Toucan website (www.toucansolution.com)
or scan the QR code.
Press and hold the SET button until
LED light on the front blinks blue to
enter the setup mode.
Solid RED
Solid BLUE
Charging Battery
Battery Fully Charged
LED Description
Flashing BLUE
Flashing PURPLE
Flashing RED
Setup Mode
Connecting to cloud server
Connection Failed
LED Description
-
1
-
2
