daltile ST53DGMTRMSCCHN Manuel utilisateur
- Taper
- Manuel utilisateur
Photo Features Xpress Mosaix Coastal Marble
Diamond Geometric Mosaic Tile
INSTALLATION INSTRUCTIONS | PERFECTFIT MOSAICS | PAGE 1 OF 6
PRESS MOSAIX™
BY
Installation of
PERFECT-FIT
MOSAICS
STEP 1: SURFACE PREPARATION STEP 2: MEASURE
CONTINUED ON NEXT PAGE
• Tile may be installed over most
structurally sound substrates.
• Make sure surface is clean, smooth,
dry and free of wax, soap scum and
grease.
• Any damaged, loose or uneven areas
must be repaired, patched and
leveled.
• Remove any moldings, trim, appliances
or anything that could interfere with
installation.
• The Perfect-Fit mosaics are designed to a
standard 18" height to fit perfectly between
the countertop and kitchen cabinets,
eliminating the need for measuring and cutting.
• If the area you desire to tile is larger than an 18"
height, start by measuring the square footage
of the wall you are planning to tile, making sure
to take into account any switches and outlets.
• Find the center point of the wall, using a level to
draw a plumb line in the wall’s center.
• Lay out a row of loose tiles across the bottom of
the wall from the center line leaving uniform joints
between tiles.
• Once you have this initial row of loose tiles laid
out, measure to determine what cuts need to be
made so that all tiles fit into the working area.
NOTE: Tiles can be butted together leaving a
consistent 1/16 in. joint automatically.
Photo Features Xpress Mosaix Coastal Marble
Diamond Geometric Mosaic Tile
INSTALLATION INSTRUCTIONS | PERFECTFIT MOSAICS | PAGE 2 OF 6
PRESS MOSAIX™
BY
Installation of
PERFECT-FIT
MOSAICS
• While cutting is not required
when installing on a standard 18"
backsplash, a ceramic tile cutter is
not recommended if any cutting is
necessary. It is recommended to use
a diamond blade. It is important to
use the proper blades because
blades designed for ceramic tile will
chip the stone.
• Wet cutting methods are
recommended to avoid inhalation of
silica dust.
NOTE: Cut edges should be placed in
corners where they can be hidden.
• If drilling a hole in the tile is
necessary, it is recommended to use
a drill bit that is specially designed
for glass, metal and stone.
NOTE: The tile must be securely
clamped into place to prevent
movement of the tile during the
drilling process.
• When drilling the hole, keep the bit
and hole lubricated to prevent
chipping.
• Drill from both sides of the tile,
starting with the back and drilling half
of the depth of the tile.
• Turn the tile over and complete the
hole. This will prevent the glass,
metal and stone from chipping as
the drill bit exits the tile.
CONTINUED ON NEXT PAGE
STEP 3: CUTTING STEP 4: DRILLING
Photo Features Xpress Mosaix Coastal Marble
Diamond Geometric Mosaic Tile
INSTALLATION INSTRUCTIONS | PERFECTFIT MOSAICS | PAGE 3 OF 6
PRESS MOSAIX™
BY
Installation of
PERFECT-FIT
MOSAICS
• It is recommended to use a white
thin-set mortar with a flexible
acrylic additive or a white polymer
fortified thin-set mortar.
• Apply this mixture with the
manufacturer’s recommendations of
a notch trowel (typically 3/16" x 3/16"
V-notch).
• Knock down the trowel ridges to
produce an even layer of the thin-set
mortar.
• Spread only enough thin-set to install
a few sheets at a time. Back-butter
each sheet with the flat edge of the
trowel. Be sure to achieve full
coverage on the back of the tile.
• Press your mosaic into the thin
set, leaving even spaces in
between tiles. A grout float can be
used to tap the tiles into place.
Allow for movement joints where
the tiles abut restraining surfaces
and around the perimeter of the
installation.
NOTE: We recommend allowing a 1/8"
joint between tiles.
• Seal the mosaic prior to grouting. Grout
with an un-sanded grout, to prevent
scratching, after the adhesive has had
proper time to cure according to the
manufacturer’s recommendations.
Seal the mosaic again after grouting.
NOTE: For more information on
proper sealants, please reference
Step 8.
CONTINUED ON NEXT PAGE
STEP 5: INSTALLATION
Photo Features Xpress Mosaix Coastal Marble
Diamond Geometric Mosaic Tile
INSTALLATION INSTRUCTIONS | PERFECTFIT MOSAICS | PAGE 4 OF 6
PRESS MOSAIX™
BY
Installation of
PERFECT-FIT
MOSAICS
• To prevent scratching, grout with
an unsanded grout after the
adhesive has had proper time to
cure.
• It is recommended to use a
non- abrasive cleaner to prevent
scratching of the tile.
NOTE: Tiles that have been
scratched prior to or during
installation are the customer’s
responsibility.
NOTE: Natural stones may darken
when wet or when in contact with
humidity.
CONTINUED ON NEXT PAGE
STEP 6: GROUTING STEP 7: CLEANING
Photo Features Xpress Mosaix Coastal Marble
Diamond Geometric Mosaic Tile
INSTALLATION INSTRUCTIONS | PERFECTFIT MOSAICS | PAGE 5 OF 6
PRESS MOSAIX™
BY
Installation of
PERFECT-FIT
MOSAICS
CONTINUED ON NEXT PAGE
• Penetrating/impregnating stone sealers are a no-sheen, natural-look sealer that
can be water-based or solvent-based.
• A premium, natural-look, penetrating/impregnating sealer is the best choice when
you are wanting to maintain the natural color of the stone. A stone-enhancer
sealer is often used when a darker, enriched, or highlighted character is desired.
• Make sure the brand you have chosen is formulated to provide
maximum stain protection for stone products.
• Stone products should be tested periodically to ensure that the sealer is working
eectively.
STEP 8: SEALING STONE TILE ONLY
Photo Features Xpress Mosaix Coastal Marble
Diamond Geometric Mosaic Tile
INSTALLATION INSTRUCTIONS | PERFECTFIT MOSAICS | PAGE 6 OF 6
PRESS MOSAIX™
BY
Installation of
PERFECT-FIT
MOSAICS
Back-butter is the spreading of a bond coat to the back of a tile before
placing the tile to ensure a strong bond with the thin-set mortar.
Balanced cuts are perimeter tile cuts of equal size that are installed on opposite
sides of the working area or on either side of a miter.
A butt joint is the thin joint created when tiles are installed side by side without the
use of spacers or gout.
The grout is a mix used for filling tile joints-most commonly created from a cement
base.
The mortar is a mixture of cement paste and fine aggregate used to bond masonry
together.
Plumb means perpendicular to true level.
The substrate is the underlying support or base of the tile installation.
ATTENTION / ATENCIÓN / ATTENTION
Do not dry cut using motorized equipment due to the potential for exposure
to harmful silica dust. Use a wet saw or a score and snap tool when cutting
is necessary during the installation process.
No corte en seco usando equipo motorizado debido a la posibilidad de
exposición a polvo dañino de sílice. En caso de que sea necesario cortar
durante el proceso de instalación, usar una sierra de corte en húmedo o
una herramienta cortadora manual.
Ne pas couper à sec à l’aide d’un équipement motorisé en raison du
risque d’exposition à la poussière de silice nuisible. Utiliser une scie à eau
ou un outil à inciser et rompre lorsqu’il faut couper pendant le processus
d’installation.
GLOSSARY OF TERMS LEGAL
-
1
-
2
-
3
-
4
-
5
-
6
daltile ST53DGMTRMSCCHN Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: daltile ST53DGMTRMSCCHN User manual
