Dimplex Opti Myst Linear Manuel utilisateur

Installation and User’s Guide

IMPORTANT SAFETY INFORMATION:

Read this manual first before attempting to install or use this electric fireplace. Always comply with the

warnings and safety instructions contained in this manual to prevent personal injury or property damage.

To view the full line of Dimplex products, visit www.dimplex.com

7216400100R03

Share the warmth and leave a review.

dimplex.com/sharethewarmth

Models

OLF46-AM

OLF66-AM

OLF86-AM

Your input helps to create even better

products and experiences.

We value your feedback!

2www.dimplex.com

Welcome ....................................................................3

IMPORTANT INSTRUCTIONS .................................................4

Technical Speciﬁcations .......................................................6

Electrical Rating .............................................................6

Product Dimensions ..........................................................6

Package Contents ............................................................7

Installation...................................................................9

Placement..................................................................9

Preparing the Firebox for Installation ............................................10

Fresh Air Inlets .............................................................10

Framing...................................................................11

Installation Instructions.......................................................12

Water Supply Connection.....................................................13

Electrical Installation.........................................................14

Heater Hardware Disconnect ..................................................16

Flame Bafes ..............................................................17

Media Arrangement .........................................................17

Front Glass Installation .......................................................18

Operation ..................................................................19

General Operation ..........................................................19

Resetting the Temperature Cutoff Switch.........................................21

Factory Reset ..............................................................22

Priming the Unit ............................................................22

Maintenance ................................................................23

Remote Control Battery Replacement ...........................................23

Cleaning ..................................................................23

Transducer Replacement .....................................................23

Servicing ..................................................................23

Troubleshooting .............................................................24

Wiring Diagrams.............................................................26

Warranty ...................................................................28

Table of Contents

3

NO NEED TO RETURN TO THE STORE

If you have questions regarding the operation of this product or if you require

service, before returning this product to the place of purchase,

Contact us at:

 www.dimplex.com/support

For Troubleshooting and Technical Support

OR  Toll-Free 1-888-346-7539

Please have your model number and product serial number ready.

QR Code label

(on pull-out bracket)

For more information on

the Flame Connect app,

visit dimplex.com/fcapp

Welcome

Thank you and congratulations for choosing to purchase a Dimplex replace.

Please carefully read and save these instructions.

WARNING: Read all instructions and warnings carefully before starting installation. Failure to follow these

instructions may result in a possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers for future reference. Model and serial numbers can be found on the

label located at the top right corner inside the replace.

Model and serial number label

(inside the replace, upper panel)

Rating label

Model MOD

Serial Number

4www.dimplex.com

When using any electrical appliance, basic

precautions should always be followed to reduce

the risk of re, electric shock, and injury to persons.

These precautions include:

① Read all instructions before using this electric

fireplace.

② This fireplace is hot when in use. To avoid burns,

do not let bare skin touch hot surfaces. The trim

around the heater outlet becomes hot during

heater operation.

DANGER: High temperatures may be generated

under certain abnormal conditions. Do not

partially or fully cover orobstruct the front of the

fireplace.

③ Extreme caution is necessary when the fireplace

is used by or near children or people with

disabilities and whenever the fireplace is left

operating and unattended.

④ Always turn off the fireplace when it is not in use.

⑤ Do not operate the fireplace after it malfunctions,

has been dropped, or damaged in any manner.

Disconnect power at the service panel and have

the fireplace inspected by a reputable electrician

before using.

⑥ Do not operate any unit with a damaged cord or

if the heater has malfunctioned, or if the heater

has been dropped or damaged in any manner,

contact Glen Dimplex Americas Technical

Service at 1-888-346-7539.

⑦ Do not use this fireplace outdoors.

⑧ Never locate the fireplace where it may fall into a

bathtub or other water container.

⑨ To disconnect the heater, turn the unit off with

the controls and turn off the power to the heater

circuit at the main disconnect panel.

⑩ Do not insert or allow foreign objects to enter

any ventilation or exhaust opening as this may

cause an electric shock, fire, or damage to the

fireplace.

⑪ To prevent a possible fire, do not block air

intakes or exhaust in any manner.

⑫ All electrical heaters have hot and arcing or

sparking parts inside. Do not use it in areas

where gasoline, paint, or flammable liquids are

used or stored.

⑬ Do not modify this fireplace. Use it only as

described in this manual. Any other use may

cause fire, electric shock, or injury to persons.

⑭ Always use a certified electrician should new

circuits or outlets be required.

⑮ Always use properly grounded, fused and

polarized outlets.

⑯ Disconnect all power coming to the fireplace at

the main service panel before performing any

cleaning, maintenance, or relocation of the unit.

⑰ When transporting or storing the fireplace, keep

it in a dry place, free from excessive vibration,

and store to avoid damage.

⑱ Regular cleaning and maintenance is required to

ensure safe and correct operation.

! NOTE: Changes or modifications not

expressly approved by the party responsible

for compliance could void user’s authority to

operate the equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

5

FCC Compliance

CAUTION: This unit has been tested and found

to comply with the limits for Class B digital

device, pursuant to part15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This unit generates, uses

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instructions, may cause harmful interference

to radio or television reception, which can be

determined by turning the unit OFF and ON,

the user is encouraged to try to correct the

interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the unit and the

receiver.

Connect the unit into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV

technician for help.

This unit complies with Part15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This unit may not cause harmful interference,

and (2) this unit must accept any interference

received, including interference that may cause

undesired operation.

FCC CAUTION: Any changes or modications

not expressly approved by the party responsible

for compliance could void the user’s authority to

operate this equipment.

IMPORTANT INSTRUCTIONS

WARNING: This product can expose you to

chemicals including nickel which is known to

the State of California to cause cancer. For more

information, visit www.P65Warnings.ca.gov

Conventions used in this manual:

! NOTE: Procedures and techniques that are

considered important enough to emphasize.

CAUTION: Procedures and techniques which, if

not carefully followed, will result in damage to the

equipment.

WARNING: Procedures and techniques which, if not

carefully followed, will expose the user to the risk of

re, serious injury, or death.

6www.dimplex.com

UL Listing

File Number: E71416

Model Reference

OLF46-AM 6911540100

OLF66-AM 6911540200

OLF86-AM 6911540300

Electrical Rating

Voltage: 120 V (3-Wire) or 240 V (4-Wire)

Power:

Model 120 V 240 V No heat (120 V)

OLF46-AM 1220 W 1920 W 520 W

OLF66-AM 1480 W 2180 W 760 W

OLF86-AM 1020 W (see note) 2400 W 1020 W

! NOTE: For OLF86-AM, when connected to 120 V, there will be no heat output, but heat functions will be active

on the controls with only fans operating.

Product Dimensions

Technical Speciﬁcations

Model A B

OLF46-AM 47 ½" 1206 mm 46 1/8"1170 mm

OLF66-AM 67 ½" 1714 mm 66 1/8"1678 mm

OLF86-AM 87 ½" 2222 mm 86 1/8"2186 mm

B

A

31 ½"

800 mm

8 ½"

217 mm

11"

280 mm

11 7/8"

300 mm

17 3/8"

441 mm

Figure1

7

Package Contents

Image Description Quantity

OLF46-AM OLF66-AM OLF86-AM

Firebox 1 1 1

Front Glass 1 1 1

Bag of Small Acrylic Crystals 2 3 4

Bag of Large Acrylic Crystals 1 1 2

Bag of Extra-Large Acrylic Crystals 111

Driftwood 8 12 15

Spare Transducer

Keep it in a secure location

for future use.

234

Suction Cup

Do not dispose of the suction cup after

installation. Keep it in a secure location

as it will be helpful for maintenance and

service of the unit.

222

8www.dimplex.com

Package Contents

Remote Control

Includes two 3 V batteries 111

User’s and Installation Guide 1 1 1

Breakable Flame Bafes 4 6 8

Slotted Flame Bafes 6 9 12

Bubble Level 1 1 1

1 ½" Wood Screws 4 4 4

*Package contents are subject to change

9

Placement

! NOTE: For optimized viewing angle of the ame, it is recommended that

the bottom of the unit be mounted between 5" (13cm) and 50" (127cm)

from the ground. (Figure 2)

Installation in a Bathroom

If this unit is installed in a bathroom, it must be protected by a GFCI

receptacle or circuit. If a receptacle is used, it must be readily accessible.

This electrical appliance is NOT watertight. To prevent electric shock, it

must be installed as to prevent water from entering unit, or installed away

from showers, tubs, etc. Never locate replace where it may fall into a

bathtub or other water container.

Installation Recommendations for Overhanging Objects

For overhanging temperature-sensitive objects, such as a television, a mantel, or artwork, always follow the

recommendations provided by its manufacturer for installation over a heater.

Installation

Figure2

5"-50" for

optimal viewing

10 www.dimplex.com

Installation

Preparing the Firebox for Installation

Figure41. The unit is provided with mounting brackets attached

(Figure 4). Remove the mounting brackets before

installation. They will need to be reinstalled during

installation once the rebox is placed into the framing.

2. If using the plug accessory kit (OLFPLUG, sold

separately), wire it following the instructions for the

plug kit in the Electrical Installation section (page 14).

3. For permanent heat disable only: follow the

instructions for disconnecting the heat function in the

section Heater Hardware Disconnect (page 16).

Fresh Air Inlets

CAUTION: Failure to include a fresh air inlet will result in poor ame performance and damage to the replace.

A fresh air inlet is required. The air inlet must allow for the air path to reach the underside of the unit. This will have to

be accounted for in the framing and drywall installation. See the table below for air inlet requirements for each model.

See Figure 3 for examples on incorporating fresh air inlets in the installation.

If the air inlet is concealed using a grille, the covered area must be compensated for by having a larger opening.

Model Air inlet area required

OLF46-AM 80 in² 516 cm²

OLF66-AM 120 in² 774 cm²

OLF86-AM 160 in² 1032 cm²

Figure3

Recessed Inlet Front Register Side Registers

* For best results in this

conguration include an opening

on each side of the replace

11

Installation

Framing

1. Prepare a wall with a framed opening, following the dimensions in the table below. Openings beneath the unit are

required in order to allow for airow to reach the underside of the unit. (Figure 6)

Framing Dimensions Drywall Opening

Model

Width

(minimum) Height Depth

(minimum) Width Height

A B C D* E*

OLF46-AM 48"

1219 mm

31 ¾"

806 mm

12"

305 mm

46 3/16"

1174 mm

17 ½"

445 mm

OLF66-AM 68"

1727 mm

66 3/16"

1682 mm

OLF86-AM 88"

2235 mm

86 3/16"

2190 mm

* Allows for a 2 mm clearance all around

CAUTION: This replace is NOT load-bearing. Ensure the opening for the replace is framed in such a way that

the weight of the building materials will not create pressure on the top of the replace.

! NOTE: Field wiring is located at the top right back corner of the rebox. The connection to water supply is

located at the bottom left back corner of the rebox. Plan the framing to allow routing the electrical power cable

and the cold-water line to this location.

! NOTE: Ensure the unit is level and ush with the framing.

A

B

C

Ensure there is an

opening to allow air

ow to reach the

underside of the unit

Figure5

D

E

Air inlet

Figure 6

12 www.dimplex.com

Installation

Installation Instructions

! NOTE: Two people are recommended for installation.

1. Follow the instructions in the section Preparing the

Firebox for Installation (page 10) before beginning.

2. Prepare a wall with a framed opening, following the

dimensions in the Framing section (page 11).

CAUTION: Ensure there is an air inlet with a path for

air ow to reach the underside of the unit.

3. Place the rebox into the framed opening. Ensure the

unit is level. A bubble level is included in the hardware

kit provided.

4. Secure the rebox to the frame using the previously

removed mounting brackets. The unit must be

secured to the frame with the mounting brackets.

! NOTE: To avoid bulging of the nished surface, notch

the framing to allow the mounting brackets to be ush

with the framing. (Figure 7)

5. Connect the unit to the water supply, following the

instructions in the section Water Supply Connection

(page 13).

6. Locate the connector plate in the top right back

corner of the unit. Remove the connector plate by

removing the 2 securing screws. (Figure 8)

7. Install a cable connector (not included), suitable for

installing in a 7/8" (22 mm) hole, to the plate and feed

the supply cable through the cable connector.

8. Complete the wiring according to instructions in the

Electrical Installation section (pages 14–15). Reinstall

the connector plate after completing wiring.

9. Finish surrounding wall up to the trim if a permanent

installation is desired. A removable trim can be used

instead to cover the framing opening to allow the

replace to be removed without damaging the nished

wall.

CAUTION: Ensure air inlets are present in nal

installation (see Fresh Air Inlets, page 10).

! NOTE: It is recommended that all drywall installation

and nishing be completed after unit is fully installed,

inspected, and operational.

10. Finish the installation using the nishing materials of

your choice.

11. Place the media as desired and install the front glass.

Mounting bracket

Notch framing for

ush installation.

Connector plate

Figure 7

Figure 8

13

Installation

Water Supply Connection

CAUTION: Ensure that all plumbing connections meet local plumbing code requirements. Ensure that the location

of the plumbing connection allows for easy access to allow for shutoff during scheduled maintenance.

Water Quality

Normal tap water can be used in the Opti-myst®. In areas with hard water, a water softener is recommended

and more frequent cleaning and maintenance may be required. Unltered water supplied from a well or another

unmonitored supply is not recommended. The product is provided with an in-line mesh lter to help remove

contaminants and extend the life of the product.

Plumbing Instructions

The units are designed to be hard plumbed by connecting to a water source using standard ¼" (6.4 mm) O.D. tubing.

A plumbing accessory kit CDFIPLUMB-KIT, designed for use with copper piping, is available from your Dimplex

dealer.

1. Prepare a cold-water line in the vicinity of the desired installation location of the replace. Ensure that the location

of the plumbing connection allows for easy access to allow for shutoff during scheduled maintenance.

! NOTE: Once the new plumbing connections are complete ensure that the lines are ushed to prevent any debris

from going into the unit.

2. Lift the media tray out of the unit and set it aside.

3. Connect the water line, reduced to ¼" tubing, to the main valve located in the bottom left side of the unit. (Figure 6)

CAUTION: Ensure that the end of the tubing is cut square to prevent leaking.

4. Connect the water supply tubing to the main water valve by removing the locking ring and inserting the tubing so

that it is fully inserted (approximately ½" [12 mm]). Reinstall the locking ring.

5. Complete electrical installation steps before opening the main water valve.

6. Priming (pre-lling with water) is required. See Priming the Unit on page 22.

Main water valve

(shown in closed position)

Figure 9

Reﬁllable Water Containers

! NOTE: Not recommended for applications with frequent use.

If direct connection to a water supply is not possible, the reservoir can be manually lled using an Opti-Myst

rellable container (9601350100RP) (not provided) which can be purchased at www.dimplex.com/replacement_parts.

One container will be needed for each ame module in the replace. One rell will provide up to 6 hours of ame

operation. The front glass and media tray will need to be removed each time the containers need to be relled.

14 www.dimplex.com

Electrical Installation

Figure 10

FIREPLACE JUNCTION BOX

Green - Ground

White - Neutral White - Neutral

Black - L

Black - L1

Red - L2

120 V

POWER

SUPPLY

(BREAKER

PANEL)

FIREPLACE JUNCTION BOX

240 V

POWER

SUPPLY

(BREAKER

PANEL)

RED

–

L2

Green - Ground

White - Neutral White - Neutral

Black - L

Black - L1

Red - L2

Installation

120 V Hardwire Installation

! NOTE: For OLF86-AM, when connected to 120 V, there will be no heat output, but heat functions will be

active on the controls with only fans operating.

1. Connect the black L1 wire from the unit to the live wire from the power supply with a wire connector.

2. Connect the white N wire from the unit to the neutral wire from the power supply with a wire connector.

3. Connect the green G wire from the unit to the ground wire from the power supply with a wire connector or

attach the grounding wire to the cover with the provided grounding screw, by placing the wire in between

screw and lock washer and tighten.

4. Ensure all wire connections are tight.

WARNING:

The installation of the electric replace must comply with the applicable Local and/or National Electrical Codes

and utility requirements.

Use the appropriate wire to meet local and national electrical codes for rated power consumption.

CAUTION: A dedicated, properly fused 15 Amp circuit is recommended, rated for the appropriate voltage (120V,

240V). A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular

basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of

the circuit breaker.

15

Optional Plug Kit (OLFPLUG, sold separately)

WARNING: Power cord option is only suitable for 120V installations.

1. Remove the 3 screws that hold the connector plate.

2. Connect the black L1 wire from the unit to the black wire of the plug kit.

3. Connect the white N wire from the replace to the white wire from the plug kit.

4. Connect green G wire from the replace to the green wire from the plug kit.

5. Ensure all wire connections are tight.

6. Secure the power cord’s pre-installed cover plate using the screws removed when removing the connector plate. The

previously removed connector plate can be disposed of.

WARNING: This heater is not intended for use with an extension cord. Plug the cord directly into an ap propriate

wall receptacle.

FIREPLACE JUNCTION BOX

Green - Ground

White - Neutral White - Neutral

Black - L

Black - L1

Red - L2

120 V

POWER

SUPPLY

(BREAKER

PANEL)

FIREPLACE JUNCTION BOX

240 V

POWER

SUPPLY

(BREAKER

PANEL)

RED

–

L2

Green - Ground

White - Neutral White - Neutral

Black - L

Black - L1

Red - L2

Figure 11

240V Hardwire Installation

You will need a 4-wire240 V supply (L1, L2, Neutral, and Ground).

1. Connect the black L1 wire from the unit to the L1 wire from the power supply with a wire connector.

2. Connect the red L2 wire from the unit to the L2 wire from the power supply with a wire connector.

3. Connect the white N wire from the unit to the neutral wire from the power supply.

4. Connect the green G wire from the unit to the ground wire from the power supply with a wire connector or attach the

grounding wire.

5. Ensure all wire connections are tight.

Installation

Figure 12

16 www.dimplex.com

Heater Hardware Disconnect

The replace heater can be permanently disabled by removing the electronic jumper on the main control board.

Heater hardware disconnect will permanently disable the heater and fan function. Follow these instructions ONLY

when an installation without heat is required. Temporary disabling of the heater can be achieved through the hidden

touch controls. See “Heat Disable” in Operation section (page 20) for instructions.

The recirculating fan and the element in the ame module will not be disabled.

To disconnect the heater and fan permanently:

1. Remove the 4 screws that secure the right-side upper LED lights and disconnect the wire.

2. Remove the 5 screws that secure the right-side upper panel. Carefully lower the upper panel, which is held by

hinges to the housing.

3. Locate the main control board. The heater hardware disconnect jumper location is labeled “J2”. (Figure 13)

4. Remove the heater hardware disconnect jumper.

5. Secure the upper panel back in its original position.

6. Reconnect the wire for the upper LED lights, and secure in place.

Figure 13

Installation

Heater Hardware

Disconnect Jumper

17

Media Arrangement

1. Install media bed with the angled side of the slot

toward the back of the replace. (Figure 17)

2. Evenly disperse the small crystals to entirely cover the

media bed.

3. Place the driftwood pieces across the crystals.

4. Place the large and extra-large crystals as desired

over the smaller crystals and beside the driftwood.

! NOTE: It is not recommended to position the

driftwood pieces across the ame output slot. If this

conguration is desired, use the provided bafes

to block the mist beneath the log(s) to prevent

condensation.

It is possible to use custom media ornaments to decorate

your replace. The custom media must t easily without

scratching the glass or bowing the media bed, and must

not be composed of sand or liquid, which could interfere

with the safety of the replace.

Installation

Flame Bafﬂes

The unit comes with breakable and slotted bafes to

create a customized ame. The unit can be operated with

or without the bafes. The bafes will create spacing to

customize a unique ame appearance.

Separate the breakable bafﬂes by bending the strip until it

breaks into 4 single bafes. (Figure 15) The slotted bafﬂes

are not breakable.

To insert the bafes, use a screwdriver to carefully pry open

the ame output slot on the top cover. (Figure 14) Install

the bafe by putting the side with the two tabs down, and

inserting it so that the lip on the top cover goes over the

bafe. (Figure 16)

Place the breakable bafes across the ame output slot as

desired to create the desired ame appearance.

Three slotted bafes are required to cover each ame

output slot.

Figure 14

Figure 17

Figure 15 Figure 16

Breakable

Bafes

Slotted Bafes

Flame Output Slot

18 www.dimplex.com

Installation

Front Glass Installation

! NOTE: Two people are required for installation of the

front glass.

1. Ensure there are no debris or nger prints on the inner

side of the front glass before you begin.

2. Attach the provided suction cups to the outer side of

the front glass. Ensure the suction cups are securely

attached.

3. Using the suction cups to assist, lift the glass and

place it directly in front of the media bed at a slight

angle.

4. Lift the front glass slightly to hook the front glass onto

the posts on each side of the replace. (Figure 18)

! NOTE: When installed correctly, the front glass should

not obstruct the hidden touch controls.

5. Remove the suction cups and clean any ngerprints or

debris off the glass with a nonabrasive glass cleaner.

! NOTE: Do not dispose of the suction cups! Keep

them in a secure location, as they may be needed for

maintenance and service on this replace.

Front Glass Post

(One on each side)

Figure 18

19

General Operation

WARNING: This electric rebox must be properly installed before it is used.

This rebox operates with Comfort$averTM technology, which automatically adjusts the fan speed and heater wattage

to safely and precisely match the requirements of the room based on the thermostat setting.

! NOTE: The element retains heat after shutdown. When the heat is turned off, there is a 30-second cool down

period before the fan shuts off completely.

! NOTE: After a power interruption the replace will return to Standby mode and retain the previously used settings.

Power Switch

The main power (On/Off) switch is located behind the front glass in the upper right corner inside the replace.

Hidden Touch Controls

The hidden touch controls are located on the upper right of the replace. (Figure 19) To activate the controls touch

the area next to the display. After 20 seconds of inactivity, the controls return to the hidden state.

! NOTE: When in standby mode, the remains illuminated.

Remote Operation

The replace is supplied with a multifunction Bluetooth remote control. (Figure 20)

App

The replace is capable of being controlled using the Flame Connect app for mobile devices. For up-to-date

information about the app, please visit www.dimplex.com/fcapp.

! NOTE: The replace will not operate using the provided remote control when the app is open on a paired mobile

device. A blue LED indicator will illuminate on the replace display when the app is in use.

Operation

Figure 19 Figure 20

Display

20 www.dimplex.com

Operation

Standby

Press to turn on the unit or to put it in standby mode. There is a brief delay after

pressing before the unit turns on.

When the unit is turned on, there is a 3-minute warm-up sequence before the ame

effect starts.

Heat

Press to turn the heat on or off.

When the heat is turned on, the display briey indicates the set temperature (##ST),

followed by the ambient room temperature.

When the heat is turned off, the fan continues to operate for a further 30 seconds to

dissipate residual heat.

Heat Disable

Press and hold and at the same time for 3 seconds to disable or enable the heat

function. This action must be performed on the hidden touch controls.

When the heat is disabled and is pressed, CD52 appears on the display.

Increase

Temperature

Press to increase the temperature setting.

The temperature can be set from 15°C to 30°C (59°F to 86°F).

Decrease

Temperature Press to decrease the temperature setting.

Temperature

Display

(°C ↔ °F)

Press and hold and at the same time for 3 seconds to change the displayed

temperature unit. This action must be performed on the hidden touch controls.

Flame Intensity

Press repeatedly to adjust the ame intensity setting. The display indicates LOW, MED

(medium), or HIGH.

! NOTE: Allow 15 minutes of operation before adjusting the ame intensity.

Extractor Fan

Boost

The extractor fan boost clears any excess fogging that may appear in the replace.

Press and hold for 5 seconds to turn on the extractor fan boost. Once nished, the

ame will resume on the low setting. This action must be performed on the hidden

touch controls.

Ambient &

Flame Theme

Press repeatedly to cycle the 8 different Ambient & ame color themes:

1 - Natural Flame

2 - Blue

3 - Violet

4 - Red

5 - Aquamarine

6 - Prism Mode - media and overhead lights cycle through colors

7 - Kaleidoscope Mode - media and overhead lights cycle through colors at

different rates.

8 - Custom (app required)

Brightness

Press repeatedly to cycle the top light brightness settings:

B1 - Brightness level 1

B2 - Brightness level 2

B3 - Brightness level 3

B4 - Brightness level 4

B5 - Brightness level 5

B6 - Pulsating effect

! NOTE: The touch screen display needs to be touched once before activating any functions below.

La page charge ...

Dimplex Opti Myst Linear Manuel utilisateur

Dimplex Opti Myst Linear Manuel utilisateur

dans d''autres langues