NuTone HV 1.5 Installation and User Manual

Marque: NuTone

Modèle: HV 1.5

Taper: Installation and User Manual

Ce manuel convient également à

Installation and User Manual

Address of your installer

06095 rev. A

AE60 / EA 1500 / HV 1.5

VB0063

RESIDENTIAL USE ONLY

INSTALLER: LEAVE THIS MANUAL WITH THE HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 20 TO 24.

READ AND SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON(S)

OBSERVE THE FOLLOWING:

1. This unit is intented for residential installation only.

2. Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer at the address or telephone number listed in the warranty.

3. Before replacing filters, servicing or cleaning unit, disconnect power cord from

electrical outlet.

4. Installation must be done in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

5. This unit is not designed to provide combustion and/or dilution air for fuel-burning

appliances.

6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

7. Do not use this unit with any solid-state speed control device other than optional wall

controls C34, CMR or ACCGSC3.

8. This unit must be grounded. The power supply cord has a 3-prong grounding plug for

your personal safety. It must be plugged into a mating 3-prong grounding receptacle,

grounded in accordance with the national electrical code and local codes and

ordinances. Do not remove the ground prong. Do not use an extension cord.

9. Do not install in a cooking area or connect directly to any appliances.

10. Do not use to exhaust hazardous or explosive materials and vapors.

11. Do not run any air ducts directly above or closer than 2 ft (0.61 m) to any furnace or

its supply plenum, boiler, or other heat producing appliance. Do not connect the unit

ducts to the furnace ducts, neither return plenum or supply.

12. When performing installation, servicing or cleaning the unit, it is recommended to

wear safety glasses and gloves.

13. When the federal, provincial or state legislation comprises more restrictive installation

and/or certification requirements, the aforementioned requirements prevail on those

of this document and the installer agrees to conform to these at his own expenses.

CAUTION

1. To avoid premature clogged filters, turn OFF the unit during construction or renovation.

2. Please read specification label on product for further information and requirements.

3. Be sure to duct air outside – Do not intake / exhaust air into spaces within walls or

ceiling or into attics, crawl spaces, or garage.

4. Intended for residential installation only in accordance with the requirements of NFPA 90B.

5. The ductwork is intended to be installed in compliance with all local and national

codes that are applicable.

6. Do not use the AE60, EA 1500 or HV 1.5 unit when varnishing. Furthermore, if the

unit is installed in the attic, it is highly recommended to block the stale air intake and

fresh air register. The varnish vapors may damage the unit.

7. At least once in a year, the unit mechanical and electronic parts should be inspected

by qualified service personnel.

8. If the AE60, EA1500 or the HV 1.5 unit is installed in the attic, the unit should not be

turned off during the winter time in order to avoid condensation inside the unit and

inside the ducts.

9. During snow/rain storm, operate the unit in recirculation mode to prevent water build

up in the ventilator.

WARNING

1. YOUR UNIT AND ITS PURPOSE . . . . . . . . . . . . . . . . . . . . . . . . .4

2. TYPICAL INSTALLATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.1 Basement Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.2 Attic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.3 Mounting Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3. INSTALL THE UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.1 Locating and Mounting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.2 Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.3 How to Hang the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.4 Planning of the Ductwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

3.5 Installing 6’’ Ducts and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-10

3.6 Insulated Flexible Ducts Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

3.7 Exterior Opening(s) Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-17

4. WALL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

4.1 Installation of the Wall Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-20

4.2 Operating the Wall Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21

5. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

5.1 Biannual Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

5.2 Annual Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

5.3 Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

6. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

TABLE OF CONTENTS

The purpose of this guide is to help you to install properly your unit, and to show you how to

operate and do the maintenance. Please read completely before starting the installation.

Please note the illustrations are typical ones.

We welcome any suggestions you may have concerning this manual and/or the unit, and

we would appreciate hearing your comments on ways to better serve you. Please forward

all correspondence to us at the address indicated on the product registration card included

with this manual.

This manual uses the following symbols to emphasize particular information:

NOTE: Indicates supplementary information needed to fully complete an instruction.

Finally, we want to congratulate you on your purchase of this excellent unit which will

allow you and your family to enjoy fresh air throughout your home for years to come!

NOTE: The unit does not require balancing because of its design.

ABOUT THIS MANUAL/PRODUCT

WARNING

Identifies an instruction which, if not followed, might cause serious

personal injuries including possibility of death.

CAUTION

Denotes an instruction which, if not followed, may severely damage the

unit and/or its components.

VF0035

OPERATIONAL PRINCIPLES

1. YOUR UNIT AND ITS PURPOSE

VF0034

CIRCULATION WITH AIR EXCHANGE:

While continually circulating the air within the house, the unit also evacuates part of this

stale air and replaces it with fresh dry air from the outside. The following extra benefits

are thus obtained: expelling the excess of humidity during the winter months, ventilate the

house on hot summer nights, elimination of stale air.

The air exchanger is designed to eliminate problems of excessive humidity, to steady the

temperature and the humidity and to filter and purify the air inside your house. The air

exchanger carries out the following operations:

AIR RECIRCULATION:

The system recirculates the air inside the house, without exchanging with the outside.

This operation steadies the temperature and the humidity throughout.

FILTRATION:

When the air flows through the system, a mechanical filter traps dust particles.

RESH AIR TO

BUILDING

FILTERED AIR

TO BUILDING

STALE AIR TO

OUTSIDE

FRESH AIR

FROM OUTSIDE

STALE AIR

FROM BUILDING

STALE AIR

FROM BUILDING

2. TYPICAL INSTALLATIONS

VH0053

Only one outside connection is needed when

using the Tandem® transition* and the dual

outside port*, simplifying the installation. These

two components are included in the installation

kit no. 15273 (purchase separately).

NOTES: 1. See Point 2.3

MOUNTING

CONSIDERATIONS

on next page

for required joists opening.

2. The installation kit no. 15273 is not

available in the U.S.A.

*Patented.

If the unit is installed in the attic, this unit must

always be in operation during the winter season.

Use the installation kit no. EA20130 (purchase

separately).

NOTE: The installation kit no. EA20130 is not

available in the U.S.A.

2.1 BASEMENT INSTALLATION

VH0004

2.2 ATTIC INSTALLATION

Use the following illustrations as guidelines to help you decide where your unit will be

installed. The unit should be hung to the joists, using chains and springs (included). If

needed, this unit can be installed upside down. For more details, see Point 3.

INSTALL

THE UNIT

In every case, bathroom fan and a range hood should be used to exhaust stale air. Also,

for homes with more than one level, we recommend one exhaust register at the highest

level.

NOTE: An electrical outlet (standard 3-prong grounding outlet) has to be available within

3 feet from the unit.

2. TYPICAL INSTALLATIONS (CONT’D)

This unit can be used for a retrofit application. Connect the existing ducts to the corresponding

unit ports. If the previous stale air to outside duct and fresh air from outside duct are 5’’

diameter, install the 5’’ diameter adapters (included) over each of the corresponding unit

ports. Also, if using the installation kit no. 15273 or no. EA20130 (not available in the

U.S.A.), install these 5’’ diameter adapters. Use 4 screws (included) per adapter to attach

them to the unit. See figure below.

The joists opening needed to install the Tandem transition must be 9¾’’ (248 mm)

minimum. Also, the maximum heigh of the tandem transition is 8¾’’ (222 mm). See

Tandem transition end view below.

NOTE: The Tandem transition is included in the installation kit no. 15273 (not

available in U.S.A.).

2.3 MOUNTING CONSIDERATIONS

VJ0030

VD0118A

8¾”

222 mm

9¾”

248 mm

3. INSTALL THE UNIT

Choose an appropriate location for the unit, far from the areas of the house where peace

and quiet are desired.

• So as to provide easy access for filter maintenance (sometimes, by

installing the unit upside down, it becomes easier to get at the filter).

• Close to an exterior wall, so as to limit the length of the insulated flexible

ducts to and from the unit.

• Away from hot chimneys and other fire hazards.

• Allow for a power source (standard 3-prong grounding outlet).

3.1 LOCATING AND MOUNTING THE UNIT

• Phillips screwdriver no. 2 or Robertson no. 2

• Scissors or utility knife (to cut duct tape and flexible ducts)

• Duct tape

• Jig saw

• A pair of metal shears (if the exterior covering of the house is aluminum

or vinyl)

• A chisel and hammer (if the exterior covering of the house is brick)

• Caulking gun and caulking

3.2 TOOLS AND MATERIALS

Use the 4 chains and springs in the hardware pack provided with the unit. According to

your needs, the unit can be installed upside down.

3.3 HOW TO HANG THE UNIT

VD0156

CAUTION

Make sure the unit is level.

3. INSTALL THE UNIT (CONT’D)

• Keep it simple. Plan for a minimum number of bends and joints. Keep the

length of the insulated ducts to a minimum.

• Do not use wall cavities as ducts. Do not use branch lines smaller than

4’’ (102 mm) diameter.

• Do not ventilate crawl spaces or cold room. Do not attempt to recover the

exhaust air from a dryer or a range hood, this would cause the clogging of

the unit.

• Be sure to plan at least one exhaust register on the highest lived-in level of

the house, if it has 2 floors or more.

3.4 PLANNING OF THE DUCTWORK

• Install the stale air exhaust register(s) in the main area where the contaminants

are produced: kitchen, living room, etc. Position the register(s) as far from

the stairway as possible and in such a way that the air circulates in all the

lived-in spaces in the house.

• If a register is installed in the kitchen, it must be located at least 4 feet (1.2 m)

from the range.

• Install the register(s) 6 to 12 inches (152 to 305 mm) from the ceiling on an

interior wall OR install it in the ceiling.

• Attach one end of the 6’’ flexible duct to the stale air exhaust register, and

the other end to the unit stale air from building port, using tie wrap and duct

tape.

3.5 INSTALLING 6’’ DUCTS AND REGISTERS

WARNING

Never install a stale air exhaust register in a room where a combustion

device operates, such as a gas water heater, a gas furnace or a fireplace.

3.5.1 STALE AIR EXHAUST DUCTWORK

• Install the fresh air distribution register(s) in a large, open area in the lowest

level to ensure the greatest possible air circulation. Keep in mind that the fresh

air register(s) must be located as far as possible from the stale air register(s).

• Install the register(s) in the ceiling OR 6 to 12 inches (152 to 305 mm) from

the ceiling on an interior wall. The duct length should be at least 15’ (4.6 m).

(The cooler air will then cross the upper part of the room and mix with room

air before descending to occupant level.)

• Attach one end of the 6’’ flexible duct to the fresh air distribution register,

and the other end to the unit fresh air to building port, using tie wrap and

duct tape.

3.5.2 FRESH AIR DISTRIBUTION DUCTWORK

CAUTION

If ducts have to go through an unconditioned space, always use insulated

ducts (purchase separately).

3. INSTALL THE UNIT (CONT’D)

3.5 INSTALLING 6’’ DUCTS AND REGISTERS (CONT’D)

3.5.3 SUGGESTED REGISTER LOCATIONS

VA0032

BUNGALOW

Basement stairwell (A): Open, lateral.

One stale air exhaust register (1) in the highest

lived-in level of the house and one fresh air

distribution register (2) in the lowest lived-in

level of the house.

VA0033

BUNGALOW

Basement stairwell (A): Closed.

One stale air exhaust register (1) in the highest

lived-in level of the house and one fresh air

distribution register (2) in the lowest lived-in

level of the house. For the closed stairwell, use

floor grilles (A).

VA0034

BUNGALOW

Basement stairwell (A): Open, central.

Two stale air exhaust registers (1) in the highest

lived-in level of the house and one fresh air

distribution register (2) in the lowest lived-in

level of the house.

3. INSTALL THE UNIT (CONT’D)

3.5 INSTALLING 6’’ DUCTS AND REGISTERS (CONT’D)

3.5.3 SUGGESTED REGISTER LOCATIONS (CONT’D)

VA0035

MULTI-LEVEL

Stairwell (A): Open, central.

Two stale air exhaust registers (1) in the upper

lived-in levels of the house and one fresh air

distribution register (2) in the lowest lived-in

level of the house.

VA0036

COTTAGE

Basement stairwell (A): Open.

Two stale air exhaust registers (1) in the upper

lived-in levels of the house and one fresh air

distribution register (2) in the lowest lived-in

level of the house.

VA0037

COTTAGE

Basement stairwell (A): One part open, some

parts closed (B).

One stale air exhaust register (1) in the highest

lived-in level of the house and one fresh air

distribution register (2) in the lowest lived-in

level of the house.

For the closed stairwell, use floor grilles (B).

3. INSTALL THE UNIT (CONT’D)

3.6 INSULATED FLEXIBLE DUCTS INSTALLATION

3.7 EXTERIOR OPENING(S) INSTALLATION

If the joists are perpendicular to the ducts, or if the connection to the exterior hood is in

a limited area, the installation will need 2 exterior hoods (or soffit grilles). Go to Point 3.7.2

or 3.7.4 for more details.

Use the following procedure for connecting the insulated flexible ducts to the unit ports

(exhaust to outside and fresh air from outside).

a) Pull back the insulation to expose the flexible duct.

b) Connect the interior flexible duct to the port using a tie wrap.

c) Carefully seal the connection with duct tape.

d) Pull the insulation over the joint.

e) Apply duct tape to the joint making an airtight seal

. Avoid compressing

the insulation when pulling the tape tightly around the joint; compressed

insulation loses its R value and causes water dripping due to condensation

on the exterior surface of the duct.

a) b) c) d) e)

NOTE: In a retrofit installation, there maybe only one insulated duct already installed for

the unit ports.

• If the unit is installed in the attic, connect this insulated duct to the exhaust to

outside port.

• If the unit is installed in the basement, connect this insulated duct to the fresh

air intake port.

CAUTION

Make sure the vapor barrier on the insulated ducts does not tear during

installation to avoid condensation within the ducts.

3.7.1 TANDEM TRANSITION WITH DUAL EXTERIOR HOOD

VJ0010

3. INSTALL THE UNIT (CONT’D)

3.7 EXTERIOR OPENING(S) INSTALLATION (CONT’D)

1. For each duct, pull back the insulation to expose the interior flexible duct.

2. Connect the interior flexible duct to the smaller part of the Tandem transition (5’’ oval)

using a tie wrap.

3. Pull the insulation over the joint. Pull the vapor barrier over the insulation.

4. Apply duct tape gently to the joint in order to make an airtight seal

. See figures below.

VJ0025

VJ0022

VJ0023

VJ0024

EXHAUST AIR TO

OUTSIDE DUCT ON

TOP SECTION

3.7.1 TANDEM TRANSITION WITH DUAL EXTERIOR HOOD (CONT’D)

CAUTION

Always connect the exhaust air to outside duct on top section of the

Tandem transition.

Dual exterior hood requires assembly. Using 2 no. 8 x 3/4” screws, assemble the top metal

screen and the plastic grille to the dual exterior hood. Then, slide the bottom metal screen to

the dual exterior hood. See illustration below.

VO0024

The dual exterior hood must be installed at a minimum

distance of 18 inches (457 mm) from the ground.

See illustration beside.

1. Using a jig saw, cut a 6’’ diameter hole

in the exterior wall and insert the

Tandem transition through this hole.

3. INSTALL THE UNIT (CONT’D)

3.7 EXTERIOR OPENING(S) INSTALLATION (CONT’D)

3.7.1 TANDEM TRANSITION WITH DUAL EXTERIOR HOOD (CONT’D)

VD0083A

18”

(457 mm)

WARNING

Make sure this hood is at least 6 feet (1.8 m) away (or more, as per applicable

building codes or standards) from sources of contamination such as:

• High efficiency furnace vent

• Any exhaust from a combustion source

• Gas meter exhaust, gas barbecue-grill

• Garbage bin

VD0084

CAUTION

The Tandem transition must be inserted in such a way that the exhaust air

to outside duct will be located on the top.

1) Exhaust air to outside duct

4. Snap the assembled exterior hood on its

backplate and secure with 2 provided

screws (no. 8 x 3/4” long).

3. Lean the exterior backplate to the exterior

wall. Using 4 no. 8 x 1½” screws, fix it to

the wall. Seal the outline with caulking.

3. INSTALL THE UNIT (CONT’D)

3.7 EXTERIOR OPENING(S) INSTALLATION (CONT’D)

3.7.1 TANDEM TRANSITION WITH DUAL EXTERIOR HOOD (CONT’D)

2. Join the end of the Tandem transition to

the rear of the exterior backplate.

Secure with 2 Xmas tree pins and seal

properly with duct tape.

VD0085

CAUTION

The exterior backplate must be installed with the word “TOP” pointing

upward.

Xmas tree pin

VD0086

VD0087

screw

3. INSTALL THE UNIT (CONT’D)

3.7 EXTERIOR OPENING(S) INSTALLATION (CONT’D)

3.7.2 LOCATING 2 EXTERIOR HOODS

If this unit installation needs to have 2 exterior hoods, an additional exterior hood must

be bought (sold separately, single exterior hood, part number 13940). Choose an

appropriate location for installing the exterior hoods.

• The dual exterior hood must be located at a minimum distance of 4 inches

(102 mm) from the ground.

• The single exterior hood must be located at a minimum distance of 18 inches

(457 mm) from the ground.

• There must be a minimum distance of 6 feet (1.8 m) between the hoods to avoid

cross-contamination. See figure below.

CAUTION

Due to its particular design, the dual exterior hood must be used only for

exhaust hood when performing an installation using 2 exterior hoods.

Use the single exterior hood for supply air.

VD0094

EXHAUST

HOOD

INTAKE

HOOD

4’’

(102

MM)

6’

1.8

6’

(1.8

18’’

(457

MM)

4’’ (102 MM)

OPTIONAL

LOCATION

WARNING

Make sure the single exterior hood is at least 6 feet (1.8 m) away (or more, as

per applicable building codes or standards) from sources of contamination

such as:

• High efficiency furnace vent

• Any exhaust from a combustion source

• Gas meter exhaust, gas barbecue-grill

• Garbage bin

3. INSTALL THE UNIT (CONT’D)

3.7 EXTERIOR OPENING(S) INSTALLATION (CONT’D)

3.7.3 CONNECTING INSULATED DUCTS TO 2 EXTERIOR HOODS

1. For each exterior hood, using a jig saw, cut a 6’’ diameter hole in the exterior wall.

Run each flexible duct through its respective hole in the wall.

2. For each exterior hood, pull back the

insulation to expose the flexible duct and,

using a tie wrap, attach it to the inner ring

of the exterior backplate. Carefully seal

with duct tape (A). Pull the insulation over

the joint. Pull the vapor barrier over the

insulation and over the outer ring of the

exterior backplate. Apply gently duct tape

to the joint making an airtight seal (B).

3. Attach the exterior backplate to the exterior

wall. Using four provided screws, fix it to

the wall. Seal the backplate with caulking,

as shown beside.

4. Snap each assembled exterior hood on its respective backplate location and

secure each of them with their 2 provided screws.

CAUTION

Make sure the insulated ductwork vapor barrier does not tear during

installation.

CAUTION

The exterior backplate must be installed with the word “TOP” pointing

upward.

VD0095

VD0096

VD0087

VD0097

SCREW

3. INSTALL THE UNIT (CONT’D)

3.7 EXTERIOR OPENING(S) INSTALLATION (CONT’D)

3.7.4 LOCATING 2 SOFFIT GRILLES

• Do not locate where prevailing winds

blow the stale air towards the fresh

air vent.

• There must be a minimum distance

of 6 feet (1.8 m) between the grilles

to avoid cross-contamination. See

illustration beside.

CAUTION

Make sure the insulated ductwork vapor barrier does not tear during

installation.

3.7.5 CONNECTING INSULATED DUCTS TO 2 SOFFIT GRILLES

1. For each exterior hole, using a jig saw, cut a

4¼’’ diameter hole in the soffit. Pull back the

insulation to expose the flexible duct. Run each

flexible duct through its respective hole.

2. Using provided screws, attach the flexible duct

to the ring of the soffit grille. Carefully seal with

duct tape. Assemble the soffit grilles to the

soffit.

VD0160

’

)

VI0014

WARNING

Make sure the air intake grille is at least 6 feet (1.8 m) away (or more, as per

applicable building codes or standards) from sources of contamination

such as:

• High efficiency furnace vent

• Any exhaust from a combustion source

• Gas meter exhaust, gas barbecue-grill

• Garbage bin

If this unit is installed in the attic, use the installation kit no. EA20130 (not available in the

U.S.A.). Choose an appropriate location for installing the soffit grilles (included in the

installation kit no. EA20130).

4. WALL CONTROL

4.1 INSTALLATION OF THE WALL CONTROL

WARNING

Always disconnect the unit before making any connections. Failure in

disconnecting power could result in electrical shock or damage of the

wall control or electronic module of the unit.

CAUTION

Never install more than one optional wall control per unit.

1. Determine the more convenient location for the control.

2. Remove the cover plate control (1). If you prefer to mount

the wall control on an approved outlet box or an approved

mounting bracket (not included), discard the backplate (2).

3. Take one end of the cable and pass it through the wall control backplate (or outlet box

or mounting bracket).

4. Splice back this end of the cable to access to the 4 wires. Remove the insulated

sleeve of each wire ends. Make a loop with each bare end wire to hook them to their

corresponding screw. Connect YELLOW wire to “Y” screw, RED wire to “R” screw,

GREEN to “G” screw and BLACK to “B” screw. See illustration below.

WARNING

To avoid risk of electrical shocks, never install another wire in the same

electrical box than the one for the wall control.

BLACK

wire

YELLOW

wire

GREEN

wire

RED

wire

WARNING

Make sure that the wires don’t short circuit between themselves or by

touching any other components on the wall control.

5. Pass the other end of the cable through the wall. Reinstall the cover plate. Using wall

anchors (not included) and provided screws, mount the wall control on the wall. See

illustrations below.

1) Wall anchors 4) Control 1) Outlet box 3) Control

2) Control cable 5) Screws 2) Control cable 4) Screws

3) Control backplate

6. Route the cable to the unit.

7. Remove the electrical box cover on the side of the unit.

8. Slide the sleeve (included) over the cable control and pass the cable through the

grommet.

1) Cable control

2) Sleeve

3) Grommet

4. WALL CONTROL (CONT’D)

4.1 INSTALLATION OF THE WALL CONTROL (CONT’D)

VC0052

VC0051

CAUTION

Keep control low voltage wiring at least 1 foot (305 mm) away from

motors, lightning ballast, light dimming circuit and power distribution

panel. Do not route control wiring along with house power wiring. Avoid

poor wiring connections. Failure to follow these practices can introduce

electrical interference, which can cause erratic control operations.

CAUTION

The sleeve must stay in the grommet. See figure below.

VD0157

1 2

9. Splice back the end of the cable to access

the 4 wires. Remove the insulated sleeve of

each wire ends. Connect each wires in their

corresponding terminal (YELLOW in “Y”,

RED in “R”, GREEN in “G” and BLACK in “B”).

10.Reinstall the electric box cover and plug the unit.

4. WALL CONTROL

4.1 INSTALLATION OF THE WALL CONTROL (CONT’D)

4.2 OPERATING THE WALL CONTROL

VE0083

FRESH AIR INDICATOR:

IGHTS UP WHEN SLIDE

SWITCH IS ON NORMAL OR

BOOST POSITION.

FILTER MAINTENANCE

INDICATOR:

LASHES EVERY SECOND TO

INDICATE IT IS TIME TO

PERFORM BIANNUAL

MAINTENANCE

. SEE SECTION 5.

LIGHTS UP WHEN ITS TIME TO

PERFORM ANNUAL

MAINTENANCE. SEE SECTION 5.

RECIRCULATION:

UNITISOPERATINGON

NORMAL SPEED WITHOUT

EXCHANGING AIR WITH

THE OUTSIDE

BOOST:

UNITISOPERATINGON

HIGH SPEED.

RESET FILTER HOLE:

ONCE THE MAINTENANCE DONE, RESET THE FILTER

MAINTENANCE INDICATOR BY CAREFULLY INSERTING

ASMALLROD

(E.G.: PAPER CLIP) IN THE RESET

FILTER HOLE, DURING 1 SECOND. THE FILTER

MAINTENANCE INDICATOR WILL TURN OFF.

NORMAL:

NITISOPERATINGON

NORMAL SPEED.

VC0055

La page charge ...

NuTone HV 1.5 Installation and User Manual

Marque: NuTone

Modèle: HV 1.5

Taper: Installation and User Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: NuTone HV 1.5

NuTone HV 1.5 Installation and User Manual

Ce manuel convient également à

NuTone HV 1.5 Installation and User Manual

dans d''autres langues

Autres documents