Fulgor Milano F6PGR486GS2 Guide d'installation

PRO-RANGE 30”- 36” -48” FULL GAS

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

INSTRUCCIONES PARA LA INSTALACIÓN

Dear Customer,

Thank you for purchasing one of our Soﬁa ranges. This range was

conceived, designed and handcrafted in Italy.

Your selection of a Soﬁa range conﬁrms you are among a special group

who share a love and passion for cooking. This unique community shares

in the experience of creating quality dishes; dishes that will satisfy the

palate while bringing the warmth of families and friends together to share

and rejoice. Impress a loved one with your ability to combine ﬂavours and

ingredients or experiment with new foods and different culinary techniques

to create unexpected pleasures.

EN

1

TABLE OF CONTENTS PAGE

1 - Special Warnings 2

Before Starting Installation 2

Mobile Home Installation 2

Recreational Park Trailers 2

2 - Product Dimensions and Cutout

Requirements 3

Anti-Tip Bracket Installation 5

3 - Installation Information 7

4 - Installation Instructions 8

5 - Gas Requirement 12

Pressure Testing 13

Pressure Test Method 13

Gas Connection 14

6 - Conversion for LP or NG Gas 15

Converting Appliance for Use with LP Gas 16

Replace Injectors (two ring flame burner) 16

Replace Injector (griddle) 17

Replace injector on (oven lower burner) 17

Replace injector on (oven grill burner) 18

Converting Appliances for Use with NG Gas 19

Pressure regulator conversion 20

INJECTORS POSITION 21

Low Flame Adjustment 23

Adjustment for Burners with one or two flame

rings: 23

Electric Gas Ignition 24

The Burner Flames 24

7Electrical Requirements 25

General Information 25

Electrical Connection 25

Electrical Requirements 26

IMPORTANT: Save these instructions for the local electrical

inspector use.

INSTALLER: Please leave this manual with owner for future

reference.

OWNER: Please keep this manual for future reference.

GLOSSARY OF TERMS: NG - Natural Gas

LP - Liquid Propane

Pay attention to these symbols present in this

manual:

DANGER

You can be killed or seriously injured if you don’t

IMMEDIATELY follow instructions.

WARNING

This is the safety alert symbol. This symbol alerts you to

potential hazards that can kill or hurt you and others. You

can be killed or seriously injured if you don’t follow these

instructions.

READ AND SAVE THESE INSTRUCTIONS.

To installer:

Leave these instructions with the appliance.

To customer:

Retain these instructions for future reference.

WARNING

If the information in this manual is not followed exactly, a fire

or explosion may resulting in product and property damage

and / or personal injury or death.

Do not store or use gasoline or other flammable vapours and

liquids in the vicinity of this or any other appliance.

Anti-Tip Bracket Installation

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Ensure the anti-tip bracket is engaged when the range is

moved. Do not operate range without anti-tip bracket installed

and engaged. Failure to follow these instructions can result in

death or serious burns to children and adults.

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

Range Foot

Anti-Tip Bracket

EN

2

Proper installation is your responsibility. Have a qualified

technician install this range.

IMPORTANT

- Observe all governing codes and ordinances.

- Write down the model and serial numbers before installing

the range. Both numbers are on the serial rating plate refer

to the illustration below.

LOCATION OF RATING PLATE

Before Starting Installation

• Check location where range will be installed. The location

should be away from strong drafty areas, such as windows,

doors and strong heating vents or fans.

• Electrical grounding is required. See “Electrical

Requirements”

• Refer to manufacturer specifications of flexible gas line to

ensure sufficient gas flow is provided to the appliance.

• Assure that electrical installation is adequate and in

conformance with National Electrical Code, ANSI/

NFPA 70 - latest edition**, or Canadian Electrical Code,

part 1 C22.1 (latest edition)*** and all local codes and

ordinances.

• Assure that gas connection conforms with local codes and

ordinances. In the absence of local codes, installations

must conform with American National Standard, National

Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition**

Canadian CAN/ CGA_B 149.1 or CAN/CGA-149.2

latest edition**

Copies of the standards listed may be obtained from:

** National Fire Protection Association One Batterymarch Park

Quincy, Massachusetts 02269

*** CSA International 8501 East Pleasant Valley Rd. Cleveland,

OH 44131-5575

NOTE: This range is manufactured for use with Natural gas

or Propane.

To convert to LP (propane) or NG (natural gas), see

instructions in the gas conversion kit provided in the

literature package. Proper gas supply connection

must be available. See gas supply requirements.

WARNING

Before connecting the appliance to the gas

supply line, ensure that its gas setting is

appropriate.

The type of gas adjusted and shipped from the

factory is indicated on the rating plate.

Mobile Home Installation

The installation of this appliances must conform to the

Manufactured Home Construction and Safety Standards, Title

24 CFR, Part 3280 (formerly the Federal Standard for Mobile

Home Construction and Safety; Title 24 HUD part 280); or

when such standard is not applicable, the Standard for

Manufactured Home Installations (Manufactured Home Sites,

Communities and Setups), ANSI A225.1 - latest edition, or

with local codes.

When this range is installed in a mobile home, it must be

secured to the floor during transit. Any method of securing the

range is adequate as long as it conforms to the standards listed

above.

In Canada, the installation of this appliances must conform

with the current standards CAN/CSA-Z240 - latest edition, or

with local codes.

Recreational Park Trailers

The installation of this appliances designed for Recreational

Park Trailers must conform with state or other codes or, in the

absence of such codes, with the Standard for Recreational

Park Trailers, ANSI A119.5.

1 - Special Warnings

IMPORTANT INSTRUCTION

Please read all instructions before using this appliance.

EN

3

2 - Product Dimensions and Cutout Requirements

PRODUCT DIMENSIONS

WIDE RANGE MODELS

29 3/4” (75.8)

35 3/4” (91.0)

47 7/8” (121.6)

7” (17.9)

1 3/8” (3.5)

3 3/8” (8.5)

TO

27 1/4” ( 69.1)

25 3/4” ( 65.4)

3/8” (1)

47 3/4” (121.4)

27 1/2” (69.7)

29 3/4” (75.6)

Max. 37 1/4” (94.7)

Min. 35 3/8” (89.8)

1" ( 2.5)

3" ( 7.6) [optional]

9" (22.8) [optional]

EN

4

2 - Product Dimensions and Cutout Requirements

CUTOUT REQUIREMENTS

ELECTRICGAS

B B

*Suggested location

of utilities

2” (5.1) max. protusion from

wall for gas or electrical supply

3” (7.6)

4” 3/4 (12.3)

A

Min. 18” (45.7)

Min. 30” (76.2)

To bottom of

ventilation hood

Min. 48” (122)

Minimum to

combustibles when

no ventilation

hood is present** Min. 18”

(45.7)

Max. 13” (33)

Min. 6”

(15.2) Min. 6”

(15.2)

C

**NOTE: Ensure your installation also complies with local and national building and fire codes.

If the surface of the entire back wall above the range and below the hood is not composed of a non-combustible material

then the 9” accessory back guard must be used.

*Consult local code for exact location requirements.

OPENING WIDTH A & C B

Range 30” 30" (76.2) 6” (15.2)

Range 36” 36" (91.4) 7” (17.8)

Range 48” 48" (122 ) 7” (17.8)

Note: Clearances from non-combustible materials are not

part of the ANSI Z21.1 scope and not certied.

Clearances to non-combustible materials must

conform with local codes or, in the absence of local

codes, with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54.

Minimum clearances:

Above cooking surface (above 36” [91.4 cm])

• Sides - 6” (15.2 cm)

• Within 6” (15.2 cm) side clearance, wall cabinets no

deeper than 13” (33.0 cm) must be minimum 18” (45.7

cm) above cooking surface

• Wall cabinets directly above product must be a minimum

of 48” (122 cm) above cooking surface, no deeper than

13” (33.0 cm).

• Rear - 0” with 9 ” backguard; 0” with non-combustible

rear wall.

• Below cooking surface (36” [91.4 cm] and below)

• Install with zero clearance between adjacent combustible

construction below the cooking surface and the back

and sides of the appliance.

CAUTION

Pro style gas ranges exhaust oven combustion air through

the rear back guard. Therefore certain cooking conditions

may result in staining or discoloration of the backsplash.

Always choose a back splash material that is suitable

for this application as Fulgor Milano will not be held

responsible for the discoloration of back splash.

ADDITIONAL CLEARANCES:

For island installation, maintain 2-½ in. minimum from

cutout to back edge of countertop and 3 in. minimum from

cutout to side edges of countertop (see top view).

For installation in a stepped island, 12” (30.5 cm) minimum

clearance is required from the back or sides of the range to

a combustible riser. The island installation is not part of the

ANSI Z21.1 scope and not certied.

FLUSH ISLAND INSTALLATION

BACK

min 3” (7.6) min 3” (7.6)

min 2 1/2” (6.3)

EN

5

2 - Product Dimensions and Cutout Requirements

Before moving the range, protect any finished flooring and

secure oven door(s) closed to prevent damage.

Vent hood Combinations:

It is recommended that these ranges be installed in conjunction

with a suitable overhead vent hood.

Due to the high heat capacity of this unit, particular attention

should be paid to the hood and ductwork installation to assure

it meets local building codes.

A hood with suitable capture area and capable of at least

450 cfm is suggested to effectively evacuate odors, steam and

heat. Choosing to install a hood of lower cfm or configured for

recirculating may compromise the effectiveness of eliminating

the aforementioned factors.

Note: some State / Provincial building codes will require

make up air systems be installed for hoods above a

certain cfm threshold (300 cfm is typical).

It is your responsibility to understand and comply with

the local requirements for gas, electrical and ventilation

where these appliances are being installed.

WARNING

Air curtain or other overhead hoods, which operate by

blowing a downward air flow on to a range, shall not be used

in conjunction with ranges with gas cooktop other than when

the hood and range have been designed, tested and certified

by an independent test laboratory for use in combination with

each other.

Clearances to horizontal surfaces above the range, measured

to the cooking surface are below. Failure to comply may

result in fire hazard.

• Installations without a hood require 48” (122) minimum

to combustibles.

• For other installations with a hood, refer to the hood

installation instructions for specific hood clearances.

CAUTION

These ranges weigh up to 400 pounds. Some disassembly

will reduce the weight considerably. Due to the weight and

size of the range and to reduce the risk of personal injury or

damage to the product:

TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.

Anti-Tip Bracket Installation

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Ensure the anti-tip bracket is engaged when the range is

moved.

Do not operate range without anti-tip bracket installed and

engaged.

Failure to follow these instructions can result in death or

serious burns to children and adults.

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or

wall.

• Slide range back so rear range foot is under anti-tip

bracket.

• See installation instructions for details.

Range Foot

Anti-Tip Bracket

EN

6

ANTI-TIP BRACKET INSTALLATION

ANTI-TIP

BRACKET

FLUSH

CABINET

SIDEWALL

BACKWALL WALL

ANCHOR

For Concrete or Cement Construction:

You must use appropriate fastening hardware (not

provided).

Secure the bracket to the wall and/or floor with at least 4

wood screws (provided).

The anti-tip bracket should be inserted into the opening on

the anti-tip brace on the range.

2 - Product Dimensions and Cutout Requirements

EN

7

3 - Installation Information

WARNING

• Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

• Cut Hazard

Beware of sharp edges. Use the polystyrene ends when

carrying the product. Failure to use caution could result in

minor injury or cuts.

Do not obstruct the ﬂow of combustion air at

the oven vent nor around the base or beneath

the lower front panel of the range. Avoid touching

the vent openings or nearby surfaces as they may become

hot while the oven is in operation. This range requires fresh

air for proper burner combustion.

NEVER cover any slots, holes or passages in the oven or

cover an entire rack with aluminum foil. Doing so blocks

air flow through the oven and may cause carbon monoxide

poisoning. Aluminum foil linings may also trap heat, causing

a fire hazard.

CHOOSING RANGE LOCATION

Carefully select the location where the range will be placed.

The range should be located for convenient use in the kitchen,

but away from strong drafts.

Strong drafts may be caused by open doors or windows, or by

heating and/or air conditioning vents or fans.

IMPORTANT NOTE

When installing against a combustible surface, a minimum

riser is required for a the range, Follow all minimum

clearances to combustible surfaces shown in the illustration

on the previous pages.

Before moving the range, protect any finished flooring and

secure oven door(s) closed to prevent damage.

Do not lift or carry the range door by the door handle.

To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the surface

units should be avoided. If cabinet storage is to be provided,

the risk can be reduced by installing a range hood that projects

horizontally a minimum of inches beyond the bottom of the

cabinets.

All openings in the wall or floor where the range is to be

installed must be sealed.

TOOLS WILL YOU NEED

Remove packaging materials and literature package from the

cooktop before beginning installation.

Remove Installation Instructions from the literature pack and

read them carefully before you begin

MATERIALS PROVIDED

Anti-tip bracket

brace abd screws

Appliance

pressure

regulator

Flare union

adaptor Gasket

MATERIALS REQUIRED (not provided)

Shut-Off Valve

Pipe Fittings

Joint Sealant

from 3-foot (* reccomended for 36'' and 48'' Full Gas

ranges) to 5-foot maximum lengh, 5/8'' O.D.

CSA-approved flexible metal gas supply.

* If a longer connection line is used it may result in

noticeably reduced performance if using many of the

burners simultaneously.

NOTE: Purchase new flexible line; do not use previously used

flexible gas line.

EN

8

4 - Installation Instructions

Do not tip the range on its side when installing the legs.The

sidewalls are not designed to bear the weight of the range

and will bend. Any damage as a result of tipping will not

be covered by warranty. Follow the method in the enclosed

installation Manual.

STEP 1

Cut the banding (1) and remove the Installation Instructions

from the top of range and read them carefully before you

begin.

CAUTION

Stand clear. The ends of the cut banding may snap

toward you.

1

STEP 2

Open the top (2) and remove the accessories (3) then lift off

the cardboard sheath (4).

3

2

4

EN

9

4 - Installation Instructions

STEP 3 (For 48” range only)

Remove the rear wood brace (5) and the front metal securing

brackets (6).

5

6

STEP 4

Slide the range back just enough to allow the rear feet to be

installed.

STEP 5

Slide back more and tilt back (9), putting the rear legs on the

floor and then mount the front legs (10) while in this angled

position supported by the rear legs and the skid.

9

10

STEP 6

Remove the base while supporting the front of the range (11)

and lower to the floor in a controlled manner (12).

11

12

EN

10

STEP 7

In case it is necessary to move the range; using the foam and/

or cardboard packaging (13), replace them around the range

strategically to protect the finished surfaces of the range from

contact with the hand-truck and any straps around the unit

(14). In the case of smaller ranges, you may use this technique

to remove the range from the skid and installing the legs (15).

Tilt the range to lower the hand-truck wheels off the skid. Place

appliance runners on the floor at the left and right sides in

front of the opening when moving into final position to protect

flooring. The oven door(s) add(s) a great deal to the overall

weight of the range, you may find it helpful to remove the

doors if moving the range a significant distance. Refer to the

included instruction manuals for how to remove and reinstall

the doors.

13

14

15

STEP 8

Some models come from the factory with the cast iron island

style trim pre-installed. If not pre-installed, follow the installation

instructions included with the island trim which also includes a

screw and bracket kit. The image below shows the installation

of the optional stainless steel accessory back guard / trims

available in island style, 3” height and 9” height for purchase

separately as accessories.

3”9”

Models 48’’

4 - Installation Instructions

EN

11

STEP 9

After completing the electrical and gas connections (see

included instructions) measure the four corners in cutout area

to verify if flooring is level. Adjust the leveling legs to the desired

height and ensure range is level. Turn the bottom section of

each leg counter-clockwise to raise the leg and clockwise to

lower it.

Ensure floor is protected. Slide unit into place making sure to

engage the anti-tip bracket.

STEP 10

Hook tabs on bottom of toekick into slots on either side of the

frame and rotate up until the magnets at the top of toekick

make contact and hold it in place securely

4 - Installation Instructions

EN

12

QUALIFIED SERVICE MAN OR GAS APPLIANCE

INSTALLER MUST MAKE THE GAS SUPPLY

CONNECTION.

Leak testing of the appliance shall be conducted by the installer

according to the instructions given.

You must install the supplied connection parts seen here in

this configuration to the main gas manifold on the appliance.

Issues arising from a failure to do so will not be covered by

warranty.

Do not install the pressure regulator backwards as the gas will

not flow correctly. Check that the arrow on the back points in

the direction of gas flow.

Parts required for connection from gas supply to regulator are

the responsibility of the installer / owner

Appliance

pressure regulator Flare union

adaptor Gasket

Appliance

ATTENTION

Use Teflon tape rated for gas applications at all threaded

connections.

Do not overtighten the connection at the manifold or you

could damage the gasket causing a leak.

WARNING

If the line pressure supplying the appliance pressure regulator

exceeds 14 inches W.C. (any gas), an external regulator

must be installed in the gas line ahead of the appliance

regulator to reduce the pressure to no more than 14 inches

W.C. Failure to do this can result in malfunction and damage

to the appliance.

Important Notes for Gas Connection

The appliance and its individual gas shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2

psi (3.5 kPa).

The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

GAS SHUT OFF VALVE

OPEN POSITION

T

O

AP

P

L

IA

N

C

E

G

AS

S

UP

P

L

Y

All supply piping, except as noted, should use common

National Pipe Thread (N.P.T.). For all pipe connections use an

approved pipe joint compound resistant to the action of LP gas.

This appliance is designed for use with NG gas or LP gas.

The gas pressure regulator is supplied with this appliance.

It must be installed in the gas ahead of the manifold entrance.

It is pre-set for use with natural gas. To use it with different

gas it must be converted, as described in the Gas Conversion

paragraph.

If at any time the appliance is to be used with a different type

of gas, all the conversion adjustments must be made by a

qualified technician before attempting to operate the range

with that gas.

The gas should be supplied to the appliance’s pressure

regulator at line pressure between 6 and 14 inches of water

column for

NG, and between 11 and 14 inches of water column for LP.

GAS REQUIREMENTS

NATURAL GAS WC

Manifold Pressure 5" (12.5 mb)

Min Line Pressure 6" (15 mb)

Max Line Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

LP GAS WC

Manifold Pressure 10” (25 mb)

Min Line Pressure 11” (27.4 mb)

Max Line Pressure 14” (34.9 mb), .5 psi (3.5 kPa)

5 - Gas Requirement

EN

13

5 - Gas Requirement

LOCATION OF GAS RATING PLATE

IMPORTANT

NEVER REUSE OLD CONNECTORS WHEN

INSTALLING THIS RANGE.

To reduce the likelihood of gas leaks, apply teflon tape or a

thread compound approved for use with LP or Natural gases

to all threaded connections.

Apply a non-corrosive leak detection fluid to all joints and

fittings in the gas connection between the supply line shut-off

valve and the cooktop inlet.

Check for leaks!

Bubbles appearing around fittings and connections will

indicate a leak. If a leak appears, turn off supply line gas

shut-off valve, tighten connections, turn on the supply line gas

shutoff valve, and retest for leaks. Never test for gas leaks

with an open flame.

NEVER TIGHTEN TO MORE THAN 35 ft lbs OF

TORQUE

CAUTION

Do not attempt to attach the flexible connector directly to an

external pipe thread.

Connection requires flare union adapters.

For Massachusetts Installations:

1. Shut-off valve must be a “T” handle gas valve.

2. Flexible gas connector must not be longer than 36 inch.

3. Not approved for installation in a bedroom or a bathroom

unless unit is direct vent.

Pressure Testing

The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 PSIG (3.5 kPa).

This appliance, as well as its individual shut-off valve, must be

disconnected from the gas supply piping system during any

pressure testing of the system at test pressures in excess of 1/2

PSIG (3.5 kPa).

When checking appliance regulator function, make certain

pressure of natural gas supply is between 6 and 14 inches of

water column or, if converted for LP gas, between 11 and 14

inches.

THE PRESSURE TESTING SHOULD BE PERFORMED BY

MEANS OF THE INJECTOR THREAD ZONE

EXPLODED VIEW OF BURNER

1

2

A

Pressure Test Method

• Remove grate and burner cap (1).

• Remove aluminum gas spreader (2).

• Temporarily remove the injectors (A).

• Connect the pressure Test instrument into injector holder

thread zone (M6x0,75).

• Check if the cooktop has the correct pressure.

• Fix the injector removed for testing and replace the parts in

the right position.

EN

14

Gas Connection

• Thread the appliances pressure regulator with 1/2” male

end connection both supplied with this appliance.

• Join the pressure regulator to the entrance threads

of the Gas Manifold with gasket supplied with this

appliance. The regulator is marked with a directional

arrow indicating correct direction of gas flow. Ensure the

appliance regulator is installed with the arrow pointing

toward the gas manifold entrance.

• Connect a manual shut-off valve to the gas supply in an

accessible location for turning on or shutting off gas to

the appliance.

• Install a coupling between the regulator and the shutoff

valve to complete the connection.

• Assure all pipe joint connections are gas tight.

• Check alignment of valves after connecting the cooktop

to the gas supply to be sure the manifold pipe has not

been moved.

FOR ALTERNATIVE PIPING METHODS TO CONNECT

THE APPLIANCE TO THE GAS SUPPLY, A TRAINED

SERVICE TECHNICIAN OR GAS APPLIANCE INSTALLER

MUST MAKE THE GAS SUPPLY CONNECTION. Leak

testing of the appliance shall be conducted by the

Installer according to the Instructions given.

Unless prohibited by local codes or ordinances, a new

A.G.A. - Certified, flexible metal appliance connector may

be used to connect this appliance to its gas supply.

The connector must have an internal diameter not less than

nominal 1/2” NPT pipe, from 3-foot (* reccomended for

36’’ and 48’’ Full Gas ranges) to 5-foot maximum lengh,

5/8’’ O.D. CSA-approved flexible metal gas supply.

* If a longer connection line is used it may result in noticeably

reduced performance if using many of the burners

simultaneously.

A 1/2” NPT x 1/2” flare union adapter is required at each

end of the flexible connector.

If a flexible connector is used assure that both the appliance

pressure regulator and manual shut-off valve are joined

solidly to other permanent hard piping (either gas supply

or the appliance manifold) so as to be physically stationary.

CAUTION

Do not attempt to attach the flexible connector directly to an

external pipe thread.

Connection requires flare union adapters.

MAXIMUM GAS POWER

NATURAL GAS

30” 92,000 Btu/h

36” 133,500 Btu/h

36” GRIDDLE 109,000 Btu/h

48” GRIDDLE 151,000 Btu/h

PROPANE GAS

30” 76,000 Btu/h

36” 111,500 Btu/h

36” GRIDDLE 93,000 Btu/h

48” GRIDDLE 127,000 Btu/h

For Massachusetts Installations:

1. Shut-off valve must be a “T” handle gas valve.

2. Flexible gas connector must not be longer than 36 inches.

3. Not approved for installation in a bedroom or a bathroom

unless unit is direct vent.

5 - Gas Requirement

EN

15

GAS CONNECTION

GASKET

FLARE UNION ADAPTOR

FLARE UNION ADAPTOR APPLIANCE PRESSURE REGULATOR

MANIFOLD SHUTOFF VALVES

FLEXIBLE APPLIANCE CONNECTOR

APPLIANCE PRESSURE REGULATOR

GASKET

FLARE UNION ADAPTOR

FLEXIBLE APPLIANCE CONNECTOR

MANIFOLD SHUTOFF VALVES

6 - Conversion for LP or NG Gas

EN

16

Converting Appliance for Use with LP

Gas

WARNING

Conversion is to be performed by an AUTHORIZED

SERVICER (or other qualified agency) in accordance with the

manufacturer’s instructions and all codes and requirements of

the authority having jurisdiction. Failure to follow instructions

could result in serious injury or property damage.

The qualified agency performing this work assumes

responsibility for this conversion.

CAUTION

Before proceeding with the conversion, shut

off the gas supply to the appliance prior to

disconnecting the electrical power

If this appliance is to converted for use with gas LP (propane

or butane), each of the following modifications must be

performed:

Gas conversion label (aluminium) to be placed on the back of

the appliance, near the data plate, after conversion has been

carried out;

Replace Injectors (two ring ﬂame burner)

1. Remove the grates and burner caps.

2. Remove aluminium gas spreader.

3. Remove the three screws from the simmer gas spreader (1).

4. Remove the two screws of the injector cover (2).

5. Remove injector (A) by using a 9-32” (7 mm) nut driver

counter clockwise.

6. Remove injector (B) by using a 9-32” (7 mm) box wrench

counter clockwise.

7. Install the injectors supplied with this appliance in the

appropriate burner. The injectors have small numbers

stamped on the side, this number corresponds with the

orifice diameter and its correct burner location (refer to

illustrations in the section: “Injectors Position”).

8. Turn clockwise to tighten (tighten to a torque of 15 to 20

inch-lbs).

9. Replace all parts following the reverse order.

10. Save the injectors removed from the appliances for future

use.

EXPLODED VIEW OF BURNER

1

2B

A

6 - Conversion for LP or NG Gas

La page charge ...

Fulgor Milano F6PGR486GS2 Guide d'installation

Ce manuel convient également à

Fulgor Milano F6PGR486GS2 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents