SPLENDID WDC 7100 XC (NA).1 Mode d'emploi

Automatic Clothes Washer

and Ventless Dryer

Instructions for use

Read All Instructions Before Using

Contents

General information, 1-2-3-4-5

Technical Information, 2-3

Important Safety Instructions, 4

Introduction, 5

Installation requirements, 6-7

Attention / Grounding instructions, 6

Electrical, location and draining, 7

Installing the washer-dryer, 8-9-10-11

Unpacking the washer-dryer, 8

Removing the transit screws, 8

Connecting the water inlets, 9

Connecting the drain hose, 9

Installing the exhaust ducting, 10

Leveling the washer-dryer, 10

Completing the installation, 11

About your appliance, 12-13-14-15

Washer-dryer special features, 12

Control panel, 13

Option buttons, 14

Program key, 14

Detergent and laundry aids, 15

Dispenser drawer, 15

Washing and drying, 16-17-18-19

Cycle Description Chart, 16

Before starting a cycle, 17

Determining load sizes, 17

Setting a wash, dry or wash-to-dry cycle, 17

Splendide laundry tips, 18

For best results, 18

Combo laundry FAQs / Sample loads, 19

Care and maintenance, 20-21

Turning off the water or electricity supply, 20

Cleaning the dispenser drawer, 20

Checking the water inlet hoses, 20

Cleaning the interior, 20

Cleaning the pump pre-chamber, 21

No lint filter to clean, 21

Troubleshooting, 22-23

Troubleshooting Chart, 22

If you need assistance, 23

2 General Information

General Information

This appliance was tested by UL and

conforms with both Canadian and

U.S. UL safety requirements and

displays their mark.

General Information 3

Technical information

Model WDC 7100 XC

Weight

Splendide 7100 XC

148 lbs.

Dimensions

Width: 23.4” (59.5 cm)

Height: 33.25”-33.75” (84.5-85.7 cm)

Depth: 22” (55.9 cm)

Minimum Installation

Clearances

Sides: 0”

Front / Back: 1”

Capacity

Washing: 2 to 15 lbs. (1 to 7 kg)

Drying: 2 to 11 lbs. (1 to 5 kg)

Electrical Connection

Voltage: 120 Volts, 11 Amp, 60 Hz

Max. Absorbed Power: 1300 Watts

Water Connection

Max. Pressure: .69 MPa (6.9 bar), 100 PSI

Min. Pressure: 0.05 MPa (0.5 bar), 7.5 PSI

Max. Spin Speed

Up to 1200 RPM

Min. Installation Spacing

This appliance may be installed in a recessed a rea, closet or alcove. The installa tion

spacing is in inches and is the minimum acceptable. *Additiona l spacing should be

considered for easy installation, servic ing and compliance with local codes and

ordinances. Installations must conform with the minimum dimensions indicated.

NOTE: The manufacturer reserves the right to make any improvements to its appliances without giving prior notice.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or

other reproductive harm.

4 General information

IMPORTANT SAFETY INSTRUCTIONS

WARNING - To reduce the risk of fire, electric shock, or

injury to persons when using your appliance, follow basic

precautions, including the following:

• Read all instructions before using any appliance.

• Do not wash or dry articles that have been previously

cleaned in, washed in, or spotted in gasoline, dry cleaning

solvents, or other flammable/explosive substances as they

give off vapors that could ignite or explode.

• Do not allow children to play on or in the appliance.

Close supervision of children is necessary when the

appliance is used near children.

• Before the appliance is removed from service or

discarded, remove the door to the washing/drying

compartment.

• Do not add gasoline, dry-cleaning solvents or other

flammable or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

• Do not install or store this appliance where it will be

exposed to the weather.

• Do not tamper with controls.

• Under certain conditions, Hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water system has not been used for such a

period, before using the appliance, turn on all hot-water

faucets and let the water flow from each for several

minutes. This will release any accumulated hydrogen gas.

As the gas is flammable, do not smoke or use an open

flame during this time.

• Turn off water faucets to relieve pressure on hoses and

valves and to minimize leakage if a break or rupture

occurs.

• Do not reach into appliance if the drum is moving.

• Repair or replacement of a part should be made only by

a qualified service technician to prevent personal injury or

damage to the machine. Contact Splendide to locate an

authorized repair service company near you.

• Do not repair or replace any part of the appliance or

attempt any servicing unless specifically recommended in

the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills

to carry out.

• Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

• Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

• Good, safe practices and caution MUST be applied when

installing, operating, and maintaining any appliance. Follow

basic precaution.

• Disconnect power to the washer at the circuit breaker or

fuse box, or unplug the machine in an emergency or when

servicicng is required. Have the installer show you and label

the proper switch or fuse at the electrical disconnect box.

• The interior of the appliance should be

cleaned periodically by qualified service personnel.

• Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire.

• Before loading the washer, make sure the drum is empty.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock by

providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-

grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local codes

and ordinances.

WARNING - Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the appliance is

properly gounded.

Do not modify the plug provided with the appliance: if it will not

fit the outlet, have a proper outlet installed by a qualified

electrician.

General information 5

Congratulations

Introduction

Congratulations on your purchase of a

Splendide. Your Spendide washer-dryer takes

the drudgery out of doing laundry - simply toss

dirty laundry in and get clean, dry laundry out!

Whether it’s installed in a luxury RV, yacht, or

apartment closet, your new Splendide is

designed to fit where others won’t and deliver

outstanding washing and drying performance

(all while conserving more energy and water

than other brands). Enjoy your new Splendide!

Read this manual

Please read this manual carefully. If you need

further assistance, please contact Splendide

Laundry Centers (Mon-Fri 7am-5pm PST)

1-800-356-0766

For your records

Write model and serial numbers here. You can find

them on the front of the machine and inside of the

door opening.

Model:

WDC7100XC

Serial No:

S/N

6 Installation requirements

Installation Requirements

For your own protection and to prevent

accidents, injury, and fire, please read the

following carefully before installing the

washer-dryer.

• Installation and grounding must be done in

accordance with local codes and by a qualified

installer. Installation Instructions provided in

this booklet are for the installers’ reference.

• Washer-dryer MUST be installed on a strong,

level floor and in a protected dry and well-

ventilated area close to a power supply and

drain outlet of sufficient capacity. DO NOT

install on carpet.

IMPORTANT: Installation on

carpet floors will cause the

machine to vibrate and may

result in excessive machine

vibration during the spin cycles

and loss of performance.

ATTENTION!

• The washer-dryer should be plugged into a

properly grounded (3) prong electrica

l outlet

capable of 120 Volt, 60 Hz, 1300 W, and

10.5 Amp. It shouldn’t be controlled by a

wall switch or pull cord which could b

e

turned off accidentally. For your safety, the

third or round grounding prong must never

be removed. DO NOT USE AN EXTENSION

CORD.

• DO NOT install or store this appliance where

it will be exposed to weather or in an area

where gasoline or other flammables a

re

stored.

ELECTRICAL SHOCK HAZARD

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death

or electrical shock.

WARNING

!

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the

event of malfunction, or breakdown,

grounding will reduce the risk of electric

shock by providing a path of least resistance

for electric current. This appliance is

equipped with a cord having an equipment

grounding conductor and grounding plug.

The plug must be plugged into an appropri-

ate outlet that is properly installed and

grounded in accordance with all local codes

and ordinances. DO NOT modify the plug

provided with the appliance. If it will not fit

the outlet, have a proper outlet installed by a

qualified electrician.

WARNING! Improper

connection of the equipment

-grounding conductor can

result in a risk of electric

shock. Check with a qualified

electrician or serviceman if you

are in doubt as to whether the

appliance is properly

grounded.

Installation requirements 7

If you have... You’ll need...

no access to Hot/Cold

water hookups

Splendide Faucet Adapter

Kit, or equivalent.

concerns about the

appliance shifting in

your RV or boat

water damage

concerns

Splendide SecureFit bracket

kit, or equivalent.

Splendide Drain-A-Way Pan,

or equivalent.

Electrical

• Machine Voltage/Amperage - 120V, 60 Hz,

1300 W, 11 Amp.

• Connection - 3-prong plug with 6’ cord is

provided with the machine.

• Circuit/Protector - 3-wire single phase, 120V,

60 Hz, AC, on a separate 15 Amp circuit.

Location

• This machine may be installed free

standing as well as in a recessed area,

closet, or alcove

• Minimum Installation Spacing - 0” on

sides and 1” in front and back. NOTE:

Additional installation spacing needs to be

considered for easy installation, servicing,

and compliance with state and federal

codes.

• Floor - Must support at least 280 lbs. and

be a solid, level surface. DO NOT install on

carpet.

• RV/Marine Installations - When locating

the appliance in a towable trailer or

watercraft, position the machine over the

axles or mid-ship where movement is at a

minimum. Block the machine to prevent

extreme movement.

• NO DRYER VENT - This appliance uses an

internal water condenser to dry laundry.

All humidity stays within the unit and is

drained as water. NO heated or

conditioned air is exhausted outside; NO

exhaust vent is needed.

Drainage

Standpipe Diameter/Capacity - Needs a 1 ¼”

minimum diameter standpipe with a minimum

carry-away capacity of 7 gallons per minute.

Top of Standpipe - Must be between 25” and 34”

high from the bottom of the machine.

Outlet End of Drain Hose (provided with the unit)

- Must be at least 20” above the bottom of the

washer-dryer. An air break must be available at the

standpipe to avoid siphoning. No more than 6” of

the drain hose should be inserted into the drain

pipe to prevent siphoning.

8 Installing the washer-dryer

IMPORTANT: Do not use excessive force.

Damage to the couplings can result. The

couplings should be tightened by hand; a

tool should only be used if a leak occurs.

IMPORTANT: Transit screws and spacers

must be removed before operating the

machine to allow proper operation of the

machine and to prevent damage to the

appliance.

Installing the washer-dryer

Unpacking the washer-dryer

• Carefully remove the packing materials with care

not to damage the drain hose and power cord

that are shipped installed on the machine.

Check that the machine is intact. Report any

damage immediately.

• Position the washer-dryer near the desired

installation position.

Removing the transit screws

For transportation, the inside of the machine is

supported by screws, rubber grommets and spacers

on the back panel. Before using the washer-dryer,

these items MUST be removed.

• After positioning

the washer-dryer

near the

installation

location, remove

the four screws

(Fig.1), with the

rubber grommets

and plastic spacers

that are attached

to them.

• Use the plastic plugs (provided in the accessories

bag) to fill in the holes.

Fig 1

Connecting the water inlets

If the water pipes you will be connecting to are new

or unused, run the water until clear to remove any

debris that could clog the water valve screens or

valves before connecting the machine. NOTE: Supply

shut-off valves should be easily accessible.

IMPORTANT: Water pressure MUST range

within the values indicated on the

“Technical Data” chart

• Included in the accessories supplied with your

machine are 2 inlet hoses with 4 rubber washers

pre installed. Check that the rubber washers are

installed in the ends of the inlet hoses to make a

water tight seal at each connection point.

• Connect the straight ends of the water inlet

hoses to the supply taps that have ¾” BSP

thread (standard hose bib).

• Connect the 90º angled ends (20 mm thread) of

these hoses to

the inlet valves

on the back of

the machine (Fig.

2). NOTE: Water

Inlet valves are

color coded:

Red (Hot) &

White (Cold).

H

C

Fig 2

WARNING! Plastic bags, styrofoam, nails

and other packaging parts are not

children’s toys and can be potentially

dangerous. Destroy the carton and plastic

bags after the washer-dryer has been

unpacked.

IMPORTANT: Retain the transit screws,

spacers and rubber tubes. These items

should be reinstalled to prevent damage if

or when you transport the machine in the

future.

Installing the washer-dryer 9

Connecting the drain hose

It is possible for the water to be discharged into a

sink, standpipe or drainpipe, but an air break must be

available at a minimum 20” height to prevent the

machine from siphoning (Fig. 6).

Standpipe Drain System - Installations require a

minimum 1 ¼” (3.2 cm) diameter standpipe with a

minimum carry away capacity of 7 gallons (26 liters)

per minute.

Wall or Floor Standpipe Drain System - The top of the

standpipe must be between 25” (62 cm) - 34” (86

cm) from the bottom of the washer (Fig. 4).

Sink Drainpipe System - Entry into the sink drain

system must be above the trap (Fig. 5). When routing

the drain hose through cabinets or walls, use a

protective material such as electrical or duct tape to

cover sharp edges that could damage the drain hose.

Use a suitable clamp to secure the drain hose to the

“Y” branch or the disposer (Fig. 7). With a sink

drainpipe system, you may connect directly: 1) to a

disposer by following the manufacturers attachment

25" (62 cm) min.

with an air break

Laundry Sink Drain

Sink Drain W/ "Y" Branch Tailpiece

Fig 5

method. 2) directly to a “Y” branch tail piece

(available at most hardware stores). 3) Through the

floor to a separate trap. The trap must be vented to

prevent siphoning. To provide proper venting, install

an Air Gap Kit (available at most hardware stores). 4)

To the faucet using a Faucet Adapter Kit (available

separately).

IMPORTANT: Make sure that the drain

hose is not kinked and that water flow is

not restricted.

• Use a U-Clamp (provided in your accessories

packet) or suitable item to secure the outlet end

of the drain hose (pre-installed on the back of

your machine).

• Insert the outlet end of the drain hose into the

standpipe, wall or floor drain (Fig. 6). NOTE:

The outlet end of the drain hose MUST be at

least 20” (50 cm) above the base of the

machine. No more than 6” of the drain hose

should be inserted into the drain pipe to prevent

siphoning.

• Use a strap, cable tie, or similar item to hold the

hose or the U-Clamp in place.

Floor Standpipe

20" (50 cm) min.

with an air break

25" (62 cm) min.

34" (86 cm) max.

6" max.

Standpipe

U-Clamp

Fig 6

A & B = 25" (62 cm) min. / 34" (86 cm) max.

Floor Standpipe Wall Standpipe

A

B

Fig 4

20" (51.8 cm) min.

34" (86 cm) max.

Standpipe

"Y" Tail Piece

This connection MUST be

before drain trap and at

least 20" (50.8 cm) above

the floor where washer will

be installed.

Cable tie

Floor Standpipe w/ "Y" Branch Tail Piece

Fig 7

10 Installing the washer-dryer

Leveling the washer-dryer

• To access the front

leveling legs, tilt the

machine backwards,

leaning it against a

wall or other stable

structure.

• Adjust the legs up

or down (Fig. 9) to

ensure the washer is

resting solid and

does not rock side-to-side or front-to-back

when the machine is upright.

• Check that the angle of inclination, measured

according to the work top, does not exceed 2°.

Fig 9

IMPORTANT: The machine must rest solid

on a sturdy floor for optimum performance

and minimum vibration.

If a cabinet door is installed, a min. opening

of 8 sq. in. should be provided for make up

air. Louvered doors with equivalent air

openings are acceptable. Allow clearances

behind door(s) to avoid rubbing between

back of cabinet door(s) and front control

panel. Additional clearances for all, door

and floor molding may be required.

Installing the washer-dryer 11

Completing the installation

• Check the electrical requirements. Be sure

that you have the correct electrical supply

and the recommended grounding method.

• Check that the shipping brackets have been

removed.

• Check that the water faucets are ON.

• Check for leaks around faucets and inlet

hoses.

• Plug washer into a grounded 3-prong outlet.

• Slide the washer-dryer to it’s final location

and confirm that it’s level.

• When installing this appliance in an RV or

marine vessel, you should block in the unit

to prevent it from shifting or tipping. A

SecureFit Bracket Kit is available from

Splendide to keep the unit from shifting

front-to-back or side-to-side.

• Test and clean the washer. Run a test load

with no laundry.

Testing and cleaning the washer,

• Press the ON-OFF button to turn the washer

ON

• Pour 1 to 2 TBSP of powder detergent into

the detergent dispenser compartment ‘2’

• Select wash program ‘2’.

• Make sure the DRY TIME knob is in the ‘OFF’

position.

• Then press START. Allow the washer to

complete the wash cycle.

12 About your appliance

About your washer-dryer

Your New Appliance

Your new appliance is an automatic washer and ventless

tumble dryer by Splendide. Front-loading with a stainless

steel drum and an extra large door opening for easy loading

and unloading. It features 10 wash programs, 7 water temp.

settings, 3 dry programs, and a 1200 RPM max. spin speed.

About Condenser Drying

This appliance dries laundry by heating the laundry inside

the drum to create steam and then cooling the outer drum.

As the steam hits the cooled surface, its condensed back

into water and is pumped out through the drain system.

This process repeats until the clothes are dry. NOTE: This

drying process does not require any outside venting,

however, it does require approx. 5 gallons of COLD water

per your of dry time. Splendides ventless models DO NOT

add moisture or humidity to the surrounding area. All

humidity stays within the unit and is drained as water.

Automatic Dispenser Drawer

Automatically dispenses laundry aids (detergent, bleach,

softener) during the cycle.

Auto Water/Energy Control

Automatically adjusts the amount of water and energy to

use for each load.

Safety Door Lock

Protects you from opening the door when it is unsafe.

Express Wash

Washes lightly soiled Cotton Heavy Duty and Permanent

Press fabrics in less time.

More Rinse Cycles

Most washers have only 1 rinse following each wash while

your Splendide washer-dryer has up to 4. It rinses 2-3

times after every wash (except Express Wash) and features

an Extra Rinse button that adds yet another rinse to

remove even more dirt/detergent from fabrics

(recommended for those with detergent contact

allergies).

Foam Removal System

Your machine automatically measures the amount of

foam in circulation and adds water to the drum to remove

excess foam for the highest rinsing performance.

Recirculating Wash Feature

With your Splendide washer-dryer, no detergent is

wasted. Water recirculates and redistributes detergent

throughout the drum in a way that assures all detergent

is dissolved for max. resource efficiency.

Automatic Balance System

Every Splendide washer-dryer incorporates the latest

motor technology. When it detects an out-of-balance

load the motor will adjust speed (or come to a complete

stop) and reposition the load automatically.

Impulse Spin Technology

Your machine features Splendides exclusive IST processor

that varies pulse in low spin for less wrinkling, less wear

on clothing, less noise, less vibration, and improved

energy efficiency.

Extra-Large Door Opening

For easier loading and unloading.

1200 RPM High Spin

For better drying performance.

Extra-Durable

Heavy duty springs, shock absorbers. Stainless steel drum.

Dryer Cool Down

The last few minutes of the dry cycle, your dryer will carry

out a cool down period. Clothing will tumble freely

without heat. This will cool fabric, buttons and snaps for

safe handling and to reduce wrinkling.

Low Maintenance

Lint passes safely through a self-cleaning pump and then

out the drain or dryer vent - so theres no messy wash or

dry filter for you to clean.

WARNING - To reduce the risk of fire, electic shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

The lightning ash with arrowhead symbol,

with-in an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sucient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the literature

accompanying the appliance.

CAUTION: To reduce the risk of electric shock, DO NOT

remove cover (or back). No user serviceable parts inside.

Refer servicing to qualied service personnel.

CAUTION RISK OF ELECTRIC SHOCK

DO NOT OPEN

About your appliance 13

DOOR LOCK

LED

ON/OFF

OPTION

Buttons

DRY TIME

Selector

CYCLE

Selector

STATUS LED’s

WASH TEMP

Selector

START

ON/OFF (Door Open) Button

Turns power to the washer ON or OFF, unlocks the

door during the wash and dry cycles. Also restarts a

SILK or WOOL cycle that’s gone into Anticrease/

Soak.

DOOR LOCK LED

Indicates when the door is locked and when it can

be safely opened:

SOLID=Locked, FLASHING=Unlocked

Once locked, the door can be unlocked for up

to 5 MINUTES into any WASH cycle and at ANY

TIME during a DRY cycle.

To unlock the door: Press the ON/OFF button.

To resume the cycle: Close the door and press the

ON/OFF button again.

START (Cancel) Button

Press once to START the program, or press and hold

to CANCEL a program in progress.

OPTION Buttons

Use these buttons to modify the wash cycle

(see “Description of Option Buttons, page 12”)

.

STATUS LED’S

Indicates the cycle phase that’s underway.

DRY TIME Selector

Use this knob to select:

A. the desired drying minutes (20 to 120) or;

B. one of the AUTO dry cycles

• Less Dry: Slightly damp clothes, easy to

iron

• Very Dry: Very dry clothes, ready to be

put away. Recommended for towels or

bathrobes. NOTE: The DRY TIME knob

does not move during the dry cycle

WASH TEMP Selector

Use this knob to select the water tempurature

(when a WASH cycle is selected. NOTE: Rinse

water is always COLD.

CYCLE Selector

Use this knob to select a WASH or DRY cycle.

NOTE: This knob does not move during the

wash or dry cycle.

Description of the control panel

IMPORTANT: The rapid flashing of the

DOOR LOCK LED together with flashing of

atleast one other LED indicates an

abnormality (see Troubleshooting)

14 About your appliance

Low

Heat

Pre

Wash

Extra

Rinse

Low

Spin

Description of the Option Buttons

You can customize the wash by adding an OPTION or combination of options

to your cycle selection. The button corresponding to the OPTION selected will

remain LIT. NOTE: If you push an OPTION button and it flashes, that means

the OPTION you selected is not available for that cycle.

EXTRA RINSE - Adds an extra rinse

to the wash cycle (Not available in

Express cycle 9)

LOW SPIN - Reduces the high spin

speed to 600 rpm (Not available in

Delicates). NOTE: This option is not

available if a Dry cycle is set.

LOW HEAT - Increases the duration

of the cooling period for the selected

dry cycle.

PRE-WASH - Adds an extra fill at the

beginning of the wash cycle

Description of the Program Key

The front of the dispenser drawer contains a Program Key to help you select a

Wash or Dry Cycle using the Cycle Selector Knob.

About your appliance 15

IMPORTANT: Adjust laundry aid amounts for

heavily/lightly soiled loads, or hard/soft water.

NEVER EXCEED the recommended amounts of

detergent or fabric softener. Doing so could

impair wash results and cause damage to the

internal parts of your machine!

IMPORTANT: NEVER USE FABRIC SOFTENER

SHEETS!

WARNING! Always dilute bleach before using.

Never overfill bleach dispenser. Excess bleach

could damage clothes.

IMPORTANT: The suds level should never rise

more than half way up to the porthole. Too much

foam will rise through the dispenser and make a

mess on your floor

IMPORTANT: Using fabric softener causes items

to release from the drum immediately after

high-speed spin, helping clothes to dry faster

while minimizing wrinkling and softening fabrics.

NOTE: Splendide recommends using 1 to 2 tbsp.

of a bio-friendly, or similar brand per wash load.

These softeners tend to appear light in color and

dissolve more quickly in less water, minimizing

build-up within your machine.

Laundry Aid Type / Amounts

Your Splendide requires smaller amounts of laundry

aids to get fabrics clean. Adding too much

detergent wont necessarily make for a more

efficient wash, and may in fact cause build up on

your clothes and inside your appliance and even

pollute the environment. Recommended laundry

aid amounts per wash load:

• Prewash detergent (Optional):

1 to 2 TBSP Powder

(or 1 TBSP Liquid)

• Detergent:

1 to 2 TBSP Powder

(or 1 TBSP Liquid)

• Fabric softener:

1to 2 TBSP (Liquid ONLY)

• Bleach (Optional):

DO NOT exceed the MAX fill line

About the Dispenser Drawer

Laundry products are diluted and dispensed

automatically at the proper time during the wash

cycle. The dispenser drawer has three

compartments (plus one removable bin) for adding

laundry products to the wash load. These

compartments are:

1

2

3

4

1 PreWash Detergent (With Bleach Bin

removed)

2 Detergent for the Wash Cycle

(Powder or Liquid)

3 Fabric Softener (Liquid)

4 Bleach (With Bleach Bin in place)

NOTE: Bleach option available in

cycle 1 (Super) wash ONLY

While not required, Splen -

dide recommends the use

of a High Efciency (HE)

detergent. HE detergents

are quick dissolving and

low sudsing and will deliver

optimum results in your

front-loading machine.

Optional

All-Natural, HE

detergent formulated

for your washer-dryer

Softens fabrics

naturally

•

Splendide Premium

Laundry Powder,

Part No. 1005

16 Washing and drying

Cycle Description Chart

Washing and drying

*

1

Su

pe

r

•

2

H

e

a

v

y

•

3

Re

g

ul

a

r

•

4

Ex

p

r

e

s

•

5

C

ot

t

o

n

D

r

y

6

H

e

a

v

y

•

7

Re

g

ul

a

r

•

8

D

eli

c

a

t

e

s

•

9

Ex

p

r

e

s

•

-

1

0

S

y

n

t

he

t

i

cs

D

r

y

1

S

i

l

k

**

•

1

2

W

oo

l

•

1

3

R

in

s

e

S

pi

n

Fabric t

y

p

e

De

g

ree o

f

so

i

l

N

o.

C

y

cle Selecto

r

Deter

g

en

t

C

y

cl

e

N

a

m

e

F

ab

ri

c

So

f

t

ene

r

O

p

tion

s

Av

a

il

ab

l

e

C

y

cle

Len

g

t

h

C

y

cl

e

Descri

p

tio

n

Ble

ach

Pr

e

W

ash

W

ash

Cotton Heav

y

Dut

y

C

y

cle

s

Permanent Press C

y

cle

s

Gentle C

y

cl

e

About Rinse, S

p

in and Drai

n

Heav

y

cotton

f

ab

ri

cs:

i.e. sheets

,

socks

,

towels,

j

eans

,

underwear

,

sweatshirts

,

etc

.

S

y

nthetic, light

cotto

n

a

n

d

more delicate

f

ab

ri

cs:

i.e. button-u

p

s

,

khakis, ra

y

on

shirts

,

etc

.

S

ilk

a

n

d

particularl

y

d

eli

cat

e f

ab

ri

cs

W

oo

l f

ab

ri

cs

Exce

p

tio

n

-

all

y

Soile

d

Heavil

y

So

ile

d

Lightl

y

So

ile

d

So

ile

d

Heavil

y

So

ile

d

Lightl

y

So

ile

d

Lightl

y

So

ile

d

So

ile

d

So

ile

d

So

ile

d

Low Heat,

Wash,

Extra

Low Spin

L

o

w He

at

Pre W

ash

Ex

t

r

a

Rin

se

Low S

p

in

L

o

w He

at

Extra Rins

e

Low S

p

in

L

o

w He

at

Low S

pi

n

L

o

w He

at

L

o

w He

at

Lo

w

H

e

at

Pre W

ash

Ex

t

r

a

Rin

se

Ex

t

r

a

Rin

se

L

o

w He

at

L

o

w He

at

Ex

t

r

a

Rin

se

Low S

p

in

1

00

min

.

90

min

.

72 min.

65

min

.

7

0

min

.

65

min

.

60

min

.

35

min

.

80

to

12

0

min

.

min

.

4

0

to

12

0

min

.

4

5

min

.

50

min

.

Timed dr

y

ing

Wash c

y

cle, rinse

c

y

cles, anticrease

a

n

d

Dr

a

in

O

NLY

.

N

O

S

C

Y

C

LE

.

Wash c

y

cle, rinse

cycles,

cycles

spin

cycles

spin cycles

800 rpm hi

g

h spi

n

Timed dr

y

ing

N

O

T

E

: A hi

g

h spin is carried out

during c

y

cle 5 (Cotton Dr

y)

for automated dr

y

ing setting

s

(hanger/iron and extra dr

y)

**

On silk c

y

cle ( 11) the dr

y

in

g

pro

g

ram is not available

.

*

Cycle lengths may vary

*

accordin

g

to water pressure,

load size and fabric t

y

p

e

N

O

T

E

: When usin

g

liquid fabric

softener, it is dis

p

ensed

automaticall

y

during the rinse c

y

cl

e

8

p

Low S

p

i

n

Varies

,

4

0

to

12

0

Le

ss

D

r

y

Less Dr

y

Extra Dr

y

L

o

w He

at

L

o

w H

eat

Extra dr

y

clothes

,

read

y

to put awa

y

Iron/hanger dr

y

-

5

80

to

14

0

min

.

9

0 to18

0

min

.

1

0

1

0

-

Extra Dr

y

Varies

,

2

0

to

12

0

min

.

9

0 to 15

0

m

i

n

.

L

o

w He

at

L

o

w He

at

Cotton s

p

in

(alwa

y

s

su

gg

este

d

)

(1200 rpm hi

g

h spin

)

Cotton rinse c

y

cle

and s

p

i

n

(1200 rpm hi

g

h spin

)

m

a

n

ual

W

ool

Less Dr

y

W

ool

1

3

1

3

L

o

w He

at

L

o

w He

at

varies

,

1

30

1

50

-

Timed dr

y

in

g

Iron/hanger dr

y

Extra dr

y

clothes

,

read

y

to put awa

y

,

NOTE: LOW SPIN option not available when a dr

y

c

y

cle is set

.

To prevent wrin

kl

es, c

y

c

l

e 11 wi

ll

end with the laundr

y

left soak an

d

t

h

e

'Rinse' LED flashin

g.

T

o

fini

sh

the c

y

cle

,

p

ress the START button

.

Extra Dr

y

W

ool

Dr

y

Time

d

Time

d

L

o

w He

at

Low S

p

i

n

Ex

t

r

a

Rin

se

Low S

p

i

n

L

o

w He

at

Note: Hi

g

h spin speed varie

s

depending on the c

y

cle

y

ou choos

e

Dr

a

i

n

Drain an

y

water from the dru

m

-

1

to

4 mi

n

35

min

.

1

6

min

.

Dr

a

in

O

NLY

.

N

O

S

C

Y

C

LE

.

Pre -

Rinse

Low Heat,

Wash,

Extra

Low Spin

Pre -

Rinse

Low Heat,

Wash,

Extra

Pre -

Rinse

Washing and drying 17

Before starting a cycle

Always make sure,

the drum is loaded correctly (see below)

the door is closed

the ON-OFF button has been pressed and machine

power is ON

laundry aids have been added to the Dispenser

Drawer (see below)

•

IMPORTANT: DO NOT attempt to open the door

when the ‘Door Lock’ LED (D) is LIT SOLID!

Bleach

(with bin)

Prewash

Detergent

(without

bin)

1 to 2 TBSP

Powder

Detergent

(or liquid

equiv.)

1 to 2 TBSP

Liquid

Fabric

Softener

Determining load sizes

Maximum WASH CYCLE capacity - Cottons: 15

lbs, Synthetics: 7.5 lbs, Silk: 3.5 lbs, Wools: 3.5 lbs

Maximum DRY CYCLE capacity - Cottons: 11

lbs, Synthetics. 7.5 lbs, Wool: 3.5 lbs.

Always allow space for air to flow around the

clothes when drying. In general, if your drying,

dont fill the drum more than 1/2 to 3/4 full.

Setting a

wash-to-dry

cycle

1) Select the wash cycle

• select a washing cycle using the Cycle

Selector;

• select the wash water temperature using the

WASH TEMP knob;

• press available OPTION buttons (optional);

2) Select the dry time

• select the length of drying time with the DRY

TIME knob; (NOTE: Average loads will dry in 90

to 120 minutes)

3) Press the START button. When the wash

cycle ends, the appropriate dry cycle will start

automatically

Setting a

wash

cycle

1) Select the wash cycle (See above);

2) Select the dry time

• set the DRY TIME knob to OFF;

3) Press the START button. When the wash

cycle ends, the machine will stop.

Setting a

dry

cycle

1) Select the dry cycle

• set the Cycle Selector to position 5, 10, or 13;

2) Select the dry time

• select the length of drying time using the DRY

TIME knob (20 to 180 min.);

3) Press the START button. When the dry cycle

ends, the machine will stop.

18 Washing and drying

Splendide laundry tips

• Wash cycles are 30 to 96 minutes.

• Dry times for average sized loads are 70 to

120 minutes

• Wash cycles use 7 to 18 gal. of water. YOU

MAY NOT SEE WATER IN THE DRUM. This is

normal.

• Once set, the DRY TIME, WATER TEMP and

CYCLE SELECTOR knobs wont move.

• The door automatically locks during the wash

and dry cycles. To unlock the door, access the

drum, then RESUME the cycle, see DOOR

LOCK LED on page 13.

Combine large and small items in one full load.

When washing single items such as a sweater,

towel or jeans, add 1 or 2 similar items to help

balance the load. Single, heavy items such as a

bathrobe can be washed separately.

Do not wash rugs that could come apart and

clog your machine.

For more delicate garments protect underwear,

tights, stockings and other small or delicate

items by placing them in a mesh laundry pouch

while washing and drying.

When using the ‘Wool’ cycle, for best results,

use a detergent that is for wool garments,

taking care not to wash more than 2.2 lbs.

For best results,

• DONT OVERLOAD THE DRUM. Keep up with

laundry by doing smaller loads every day or

two.

• DONT EXCEED RECOMMENDED DETERGENT

OR FABRIC SOFTENER AMOUNTS.

• When going from was-to-dry automatically,

Always use a fabric softener (Or a Detergent

with built-in softeners) so clothes release from

the drum after the high speed spin.

• ONLY use Cotton Heavy Duty for heavy

cottons (towels, jeans, etc.)

• For items that may wrinkle, use Low Spin in

wash and Synthetics Dry

• To further prevent wrinkles, set a wash

ONLY cycle with LOW SPIN pressed. After the

wash cycle ends, remove large items (pants,

sheets, etc.) from the drum and shake them

out. Loosely fold them and place them back in

the drum. Then set a Synthetics Dry cycle with

LOW HEAT pressed.

• For mixed DRY CYCLE loads, remove items

that may wrinkle while still damp (dress shirts,

etc.) Hand press and hang them. Then,

continue drying the rest (underwear, towels,

etc.)

• NEVER OVER DRY LAUNDRY. Over drying is a

major cause of wrinkling. A certain amount of

humidity is what makes fabrics soft and fluffy.

WARNING!

During the drying phase, the door tends to get

quite hot.

Do not use the appliance to dry clothes that have

been washed with flammable or chemical

solvents (e.g. trichlorethylene).

This appliance can only be used to dry clothes

that have been pre-washed in water.

Do not use the appliance to dry foam rubber or

similar materials

Washing and drying 19

Sample wash-to-dry loads

To get you started, here are a few sample load sizes that

can go directly from wash through dry. NOTE: Data

purely indicative. Actual drying times will vary depend-

ing on type/weight of material.

Sample Load 1

 Wash Cycle: Regular Cotton Heavy Duty/ Dry Time:

120 min.

 2-3 Bath Towels (27 x 52 / all 100% cotton)

 1 Hand Towel (16 x 28)

 1-2 Wash Cloth(s) (13 x 13)

Sample Load 2

 Wash Cycle: Regular Cotton Heavy Duty/ Dry Time:

70 to 120 min.

 1 Flat Sheet (90 x 102 / all 230 thread count)

 1 Fitted Sheet (60 x 80)

 2 Standard Queen Pillowcases (21 x 32)

Sample Load 3

 Wash Cycle: Regular Cotton Heavy Duty / Dry Time:

70 to 95 min.

 1 Hand Towel (16 x 28)

 1 Pair Jeans (35 waist/32 inseam)

 1 Sweatshirt (Large, 50% cotton, 50% polyester)

Combo laundry FAQ’s

Is using a combination washer-dryer much

dierent than what I’m use to?

Yes, in some ways. You are washing and drying

in the same drum and load sizes are smaller.

Wash cycles are similar, but because combina-

tion washer-dryers are compact and operate

using 115V (vs. 230V), dry times are longer.

Instead of washing several, bulky loads of

laundry in one day, you’ll learn to adjust your

laundry habits to launder smaller, more conve-

nient loads every day or two.

Why do I need to load my drum less full for ‘dry’

and ‘wash-to-dry’ cycles?

Your machine can wash larger loads than it can

dry. Remember, separate washers and dryers

have drums of dierent sizes (the dryer drum is

usually 2 times bigger), and your machine

washes and dries in the same drum. When you

program your machine to ‘dry’ or ‘wash-to-dry’

you must load the drum no more than 1/2 to

3/4 full. (NOTE: Automatic wash-to-dry not

available when Silk is selected)

What factors aect drying times?

Drying times depend largely on the type of

material (some bers absorb more water than

others), and the dampness of the articles when

drying is started (1200 RPM spin vs. 800- 600

RPM spin), and on the amount of laundry that is

being dried. Jeans, towels and similar (rather

thick) articles will take longer to dry.

20 Care and maintenance

Care and maintenance

Turning off the water or

electricity supply

Turn off the water supply after every wash. This

will limit the wear of your appliances water

system and also prevent leaks. Unplug your

appliance when cleaning it, while on vacation

and during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance

can be cleaned with a soft cloth soaked in

lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the dispenser

drawer

Remove the dispenser by raising it and pulling it

out. Wash it under running water; repeat as

needed.

Caring for your appliance

door and drum

When not in use, leave the appliance door ajar

to prevent unpleasant odors from forming.

Checking the water inlet

hoses

Check the water inlet hoses at least once a year.

Clean the filters and the water valves. If you see

any cracks, bulges or wear, replace hoses

immediately; During the wash cycles, water

pressure is very strong and a cracked hose could

easily split open.

Cleaning the interior

The interior of the machine should be cleaned

periodically by a qualified service technician. Over

time, continual oversudsing can clog up the

condensing chamber and fan blower with lint and

reduce drying efficiency.

IMPORTANT: Replace the inlet hoses at least

every ve years of use to reduce the risk of hose

failure. When replacing the inlet hoses, mark the

date of replacement on the label with a perma-

nent marker.

WARNING! Never use inlet hoses that have

already been used.

La page charge ...

SPLENDID WDC 7100 XC (NA).1 Mode d'emploi

SPLENDID WDC 7100 XC (NA).1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents