Sony RM-VL600T Le manuel du propriétaire

2-685-367-11 (1)

Integrated Remote

Commander

RM-VL600T

Operating Instructions

Mode d’emploi

GB

FR

2

GB

Disposal of Old Electrical & Electronic

Equipment (Applicable in the European

Union and other European countries with

separate collection systems)

This symbol on the product or on its packaging indicates that this

product shall not be treated as household waste. Instead it shall be

handed over to the applicable collection point for the recycling of

electrical and electronic equipment. By ensuring this product is disposed

of correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by

inappropriate waste handling of this product. The recycling of materials

will help to conserve natural resources. For more detailed information

about recycling of this product, please contact your local Civic Office,

your household waste disposal service or the shop where you purchased

the product.

3

GB

Features

The RM-VL600T Remote Commander provides centralised control of all

your AV components from a single remote commander and saves the

trouble of operating different AV components with different remote

control devices. The following are its main features.

Centralised control of Sony AV components with this one remote

commander

This Commander is preset at the factory to operate Sony brand

components, so you can use it out of the box as a control centre for your

Sony AV components.

Remote control signals for non-Sony components are also preset

This Commander is preset for most major brands components as well as

Sony. You can remote control your non-Sony components by setting the

type and code number of each component (page 10).

Learning function for programming various other remote control

signals

This Commander has a Learning function, to “learn” the remote control

signals needed to operate other non-preset components or functions. (To

“teach” such signals to this Commander, use the remote control supplied

with the non-preset components.) (page 16)

In addition, the Commander can “learn” remote control signals (infrared

signals only) of non-Audio Visual components such as air-conditioners,

lights, etc. (Some specific appliances or functions may not be available.)

(page 24)

Reassigning new components

You can assign Component Select buttons to freely operate other

components. This is useful when you have more than two of the same

kind of AV component (only if a Component Select button is free.) (page

33)

You can only assign TVs to the TV Component Select button.

You can only assign an amplifier to the AMP Component Select button.

GB

Startup Guide

This guide shows you how to set the Remote Commander to operate

your components.

First, find the four-digit component code number for your

component, referring to the supplied “Component code numbers.”

Example: To set up a TV of

the code number “8011”

1 Set the Remote

Commander for code input

mode.

2 Press the desired

Component Select button.

3 Enter the code number.

4 Finish setting.

SET

MENU

+

Press SET and MENU.

SET

SATDVDTV CBL

TAPE

CDVCR AMP

ENT

Press ENT.

You can search for the

component code available for

your component.

1 Set the Remote

Commander for code

input mode.

2 Press the desired

Component Select button.

3 Transmit code number

signals in turn.

4 Finish setting.

SET

MENU

+

Press SET and MENU.

SET

SATDVDTV CBL

TAPE

CDVCR AMP

PROGRAM

1

ENT

Press ENT.

8 0 1 1

For more details, see page

13

.

Press PROGRAM + or PROGRAM

–, and then 1. Repeat until

your component reacts.

If you have the code

number

If you cannot find the

code number

For more details, see page

10

.

4

GB

1 Place the RM-VL600T head

to head with your VCR’s

remote control.

2 Set the RM-VL600T for

“learning” mode.

Press and hold SET for at least

3 seconds until the SET

indicator flashes.

3 Press the desired

Component Select button.

If your component does not work as supposed even if the code

number is set, make the RM-VL600T “learn” the functions of

your component’s remote control.

Learning function

Example: To “teach” the N (play) signal of your video cassette

recorder to the VCR N button of the RM-VL600T

VCR’s remote

control

RM-VL600T

SET

VCR

4 Press the button you

want to “teach.”

5 Press and hold the N

(play) button of your

VCR’s remote control until

the VCR button of the

RM-VL600T lights up.

6 Repeat Steps 4 and 5 to

“teach” other functions.

7 Finish setting.

For more details, see page 16.

5 – 10 cm

(2 – 4 inches)

away (approx.)

SET

Press SET.

5

GB

6

GB

Table of Contents

Startup Guide ...............................................................................................4

Getting Started

Installing the Batteries ................................................................................. 8

When to replace the batteries ............................................................................ 8

Location of Controls .....................................................................................9

Basic Operations

Setting the Code for non-Sony Preset Audio and Visual Components

— Setting component codes ................................................................... 10

Setting a component code ................................................................................ 10

Checking if the code number works .............................................................. 12

Setting a Component Code by the Search Function ................................... 13

Operating Your Components with the Remote Commander ......................14

To control the volume ....................................................................................... 15

Programming Signals of Another Remote Control — Learning Function ... 16

For accurate Learning ....................................................................................... 19

Programming remote control signals to the

Component Select buttons and System Control buttons ......................... 20

Changing or erasing the function of a “learned” button ............................ 22

Notes on programming the signals for an air-conditioner ......................... 24

Advanced Features

Controlling the Volume of Visual Components Connected to an Audio

System ...................................................................................................... 25

Adding an Extra Function to the Component Select Buttons ..................... 27

Programming the Power-On command of the selected component just

by pressing that Component Select button

(for Sony components only) ......................................................................... 27

Executing a Series of Commands — System Control Functions .................29

To clear programmed commands ................................................................... 31

Programming a Series of Commands on the Component Select

Buttons .....................................................................................................32

To clear programmed commands ................................................................... 33

Assigning Other Components to the Component Select Buttons ..............33

Using Other Functions

Locking the Controls — Hold Function ....................................................... 34

Erasing All Settings — To reset the Commander to its factory settings .... 35

7

GB

Additional Information

Precautions ................................................................................................. 36

Maintenance ............................................................................................... 36

Specifications .............................................................................................. 36

Troubleshooting ..........................................................................................37

Appendices

Table of Preset Functions ............................................................................ 39

TV(ANALOGUE) .............................................................................................. 39

TV(DIGITAL) ..................................................................................................... 40

VCR ..................................................................................................................... 41

CBL (Cable box) ................................................................................................. 41

SAT ...................................................................................................................... 42

SAT (No,3201) .................................................................................................... 43

DVD .................................................................................................................... 44

CD ....................................................................................................................... 45

MD....................................................................................................................... 45

DAT ..................................................................................................................... 45

DECK .................................................................................................................. 46

AMP .................................................................................................................... 46

Index ...........................................................................................................47

8

GB

Getting Started

Installing the

Batteries

Slide open the battery

compartment lid and insert two

R6 (size AA) batteries (not

supplied). Be sure to match up the

+ and – indications on the

batteries with the + and –

indications on the battery

compartment.

When to replace the

batteries

Batteries for remote control

operation (two R6 (size AA)

batteries)

Under normal conditions, the

batteries will last up to six

months. If the Commander does

not operate properly, the batteries

might be drained. When this

happens, replace the batteries with

new ones.

Note

Do not take more than one hour to

replace the batteries. Otherwise, your

code number settings (page 10) and

“learned” remote control signals (page

16) will be erased.

Notes on batteries

• Do not use an old battery with a new

one, or mix different types of

batteries together.

• If the electrolyte inside the battery

should leak, wipe the contaminated

area of the battery compartment with

a cloth and replace the old batteries

with new ones. To prevent electrolyte

from leaking, remove the batteries if

you plan not to use the Commander

for a long period of time.

Insert the batteries (negative end

first) through the guide clamp

within each compartment as

shown above.

9

GB

Location of Controls

1 SET indicator

2 SET button

3 Component Select buttons

Light or flash during operation.

4 Number buttons

5 - button

6 DIGITAL button

7 2 (volume) +/– buttons*

8 (PAP) button

9 % (muting) button*

0 GUIDE button

qa RETURN button

qs Player Control buttons

qd t (input select) button

qf 1 (power) button

qg ENT (enter) button

qh ANALOG button

qj PROGRAM +/– buttons

qk / (Teletext) button

ql (recall) button

w; MENU button

wa Cursor Control buttons

ws TOOLS button

wd SYSTEM CONTROL buttons

SET

SATDVDTV CBL

TAPE

CDVCR

1

VIDEO1

2

VIDEO2

3

AUX

4

TUNER

5

CD

6

TAPE

7

MD

8

TV

9

PHONO

0

DVD

GUIDE MENU

TOOLS

SYSTEM CONTROL

AMP

ENT

OK

ABCD

1

-/--

RETURN

ANALOG

DIGITAL

PROGRAM

1

2

qd

qf

qg

qh

qj

qk

ql

w;

wa

wd

ws

1

6

7

8

9

q;

qa

qs

2

5

3

4

About tactile dots

The number 5 button, the N button and PROGRAM + button each have a tactile

dot for ease of use.

* Note on the 2 +/– and % buttons

The Commander controls or mutes the TV’s volume when you select a visual

component. The Commander controls or mutes the amplifier’s volume when you

select an audio component. You can change this setting (page 25).

Note

The function of the control buttons varies depending on settings/operating modes.

The “Table of Preset Functions” (page 39) shows how the Commander generally

operates for each component in the factory preset mode.

10

GB

SET

SATDVDTV CBL

TAPE

CDVCR

1

VIDEO1

2

VIDEO2

3

AUX

4

TUNER

5

CD

6

TAPE

7

MD

8

TV

9

PHONO

0

DVD

GUIDE MENU

TOOLS

SYSTEM CONTROL

AMP

ENT

OK

ABCD

1

-/--

RETURN

ANALOG

DIGITAL

PROGRAM

1 2

2

4

5

2

3

2 Press and while holding

SET, press MENU.

The SET indicator lights up.

Example: To set up a Philips’ TV

1 See the tables in the

supplied “Component code

numbers,” and find the

four-digit component code

number for the desired

component.

If more than one code number

is listed, use the number that is

listed first.

For example, to set up a

Philips’ TV, you would use the

code number 8086.

Setting a component code

SET

MENU

+

Note

An MD player can be set to any of the

above Component Select buttons. You

can assign Component Select buttons to

freely set signals of your desired

components. For further information,

see “Assigning Other Components to

the Component Select Buttons” (page

33) .

For the functions of buttons as for each

component, see “Table of Preset

Functions” (page 39).

Basic Operations

Setting the Code for

non-Sony Preset

Audio and Visual

Components

— Setting

component codes

The Commander is preset at the

factory to operate Sony brand AV

components (see the table below).

If you are using the Commander

with a factory-set Sony

components, skip the following

procedures.

You can use the Commander with

other major brand preset AV

components also. To use with

other AV components, or Sony

components which do not

function with the Commander,

you need to follow the procedures

to set the correct codes for each

component.

Component

Select button

TV

DVD

SAT

CBL

VCR

CD

TAPE

AMP

Factory setting

Sony TV

Sony DVD

player

Sony satellite

tuner

Analogue

cable box

Sony VHS

VCR

Sony CD

player

Sony cassette

deck

Sony amplifier

Preset

component(s)

TV

TV/VCR

Combo

DVD player

Satellite

tuner

Cable box

VCR

CD player

Cassette

deck

Amplifier

11

GB

3 Press the Component Select

button for the desired

component.

The SET indicator and the

selected Component Select

button light up.

4 Press the Number buttons

to enter the four-digit

component code number.

5 Press ENT.

The SET indicator and the

Component Select button light

turn off.

If the Component Select button

flashes five times before

turning off, it means that the

setup is incomplete. Start over

from Step 2.

Continued

Notes

• If you press a component code

number that is not on the table in the

supplied “Component code

numbers,” or if you press a button in

the wrong order, the Component

Select button flashes five times, and

then turns off. Check the component

code number, and try setting it again.

• If you do not input anything into the

Commander within 20 seconds

between each step, the setup

procedure will be cancelled. To set the

code, start over from Step 2.

•

If you press SET while setting the

component code, all code numbers will

be lost, and the setup procedure will

be cancelled. Start over from Step 2.

To cancel setup, press SET.

TV

SET

SATDVDTV CBL

TAPE

CDVCR AMP

TV TV

12

GB

Setting the Code for non-Sony

Preset Audio and Visual

Components — Setting

component codes (continued)

Checking if the code

number works

1 Power on the component

with its power switch.

2 Press the corresponding

Component Select button

for the component you

have set up.

The Component Select button

lights up when you press it,

and turns off when you release

it.

3 Aim the Commander at the

component and press 1.

The selected Component Select

button lights up when you

press a function button, and

turns off when you release it.

The component should power

off.

4 If you have succeeded,

check that the Commander

is operating the other

functions of your

component, such as

programme and volume

control.

See page 14 for details.

If the Commander does not

seem to be working

Try repeating the setup procedure

using the other codes listed for your

component, or try setting the code

number using the Search function

(page 13).

Note on the 2 +/– and %

buttons

When you operate a visual

component, the TV button lights

up to indicate that the

Commander is controlling or

muting the TV’s volume.

When you operate an audio

component, the AMP button lights

up to indicate that the

Commander is controlling or

muting the amplifier’s volume.

It is recommended that you first

set the TV and AMP codes before

setting up any other components.

Note on buttons that have

already “learned” remote

control signals

If another signal has already been

programmed on a button using

the Learning function (page 16),

that “learned” signal will continue

to work even after you set the

component code number. To use it

as a preset function button, you

must first erase its “learned”

signal (page 22).

TV TV

SATDVDTV CBL

TAPE

CDVCR AMP

1

TV

AMP

13

GB

1 Press and while holding

SET, press MENU.

The SET indicator lights up.

2 Press the Component Select

button for the desired

component.

The SET indicator and the

selected Component Select

button light up.

3 Press PROGRAM + or

PROGRAM –, and then 1

in turn until the component

reacts as described in the

following.

TV, AMP: Powers off

VCR, CBL, SAT, DVD:

Powers on

CD player, MD player, cassette

deck: Plays back

Press PROGRAM + to go to the

next code number.

Press PROGRAM – to go back

to the previous code number.

The Component Select button

flashes three times after the

numbers have turned one cycle.

One cycle means, for example,

the four-digit code numbers

beginning from “8” are cycled

through.

SET

SATDVDTV CBL

TAPE

CDVCR

1

VIDEO1

2

VIDEO2

3

AUX

4

TUNER

5

CD

6

TAPE

7

MD

8

TV

9

PHONO

0

DVD

GUIDE MENU

TOOLS

SYSTEM CONTROL

AMP

ENT

OK

ABCD

1

-/--

RETURN

ANALOG

DIGITAL

PROGRAM

1 2

1

2

4

3

1

Setting a Component

Code by the Search

Function

You can find a code number

available for a component that

does not have one in the supplied

“Component code numbers.”

Before starting the Search

function

Set each component to the

following status so that the Search

function works effectively.

TV, AMP: Power-on

CD player, MD player*, cassette

deck: Power-on with a playback

source (disc, cassette tape, etc.)

Other components: Power-off

* If any of these components are

assigned to any of the

Component Select buttons (page

33), you can set a component

code using the Search function.

Continued

SET

TV

SET

SATDVDTV CBL

TAPE

CDVCR AMP

PROGRAM

1

SET

MENU

+

14

GB

Example: To operate a video

cassette recorder

1 Press the desired

Component Select button.

The Component Select button

lights up when you press it,

and turns off when you release

it.

4 Press ENT.

The SET indicator and the

Component button turn off.

If the Component Select button

flashes five times before

turning off, it means that the

setup is incomplete. Start over

from Step 1.

5 Check if the code number

works by following the

instructions on page 12.

Notes

• If you do not input anything into the

Commander within 20 seconds

between each step, the setup

procedure will be cancelled. To set the

code, start over from the beginning.

• If you press any button other than

PROGRAM +/– and 1 while setting

the component code, all code

numbers will be lost, and the setup

procedure will be cancelled. Start

over from the beginning.

To cancel setup, press SET.

SET

SATDVDTV CBL

TAPE

CDVCR

1

VIDEO1

2

VIDEO2

3

AUX

4

TUNER

5

CD

6

TAPE

7

MD

8

TV

9

PHONO

0

DVD

GUIDE MENU

TOOLS

SYSTEM CONTROL

AMP

ENT

OK

ABCD

1

-/--

RETURN

ANALOG

DIGITAL

PROGRAM

1 2

1

2

TV TV

Setting a Component Code by

the Search Function (continued)

VCR VCR

Operating Your

Components with the

Remote Commander

When you operate a non-Sony

component, make sure you set the

component code first (page 10).

ENT

15

GB

To control the volume

Press 2 +/– to control the

volume. Press % to mute the

sound.

When you select a visual

component, the TV’s volume will

be controlled (TV Component

Select button lights up), and when

you select an audio component,

the amplifier’s volume will be

controlled (AMP Component

Select button lights up). You can

change this setting (page 25).

Notes

• If you used the Learning function

(page 16) to programme the 2 +/–

or % button to send a signal to any

other component, that signal will be

transmitted instead of the volume or

muting of the TV or amplifier when

you select that component.

• If you used the Learning function

(page 16) to programme the 2 +/–

or % button for the TV or AMP

buttons to send a signal to any other

component, that signal will be

transmitted only when you select TV

or AMP. When you select another

component, the preset volume control

signals for TV or AMP will be

transmitted.

• If you have assigned another

component to the TV or AMP buttons

(page 33), the volume of the TV or

amplifier cannot be controlled even if

you select another component.

2 Press any Player Control

button.

See “Table of Preset Functions”

(page 39) for the functions of

buttons for each component.

Note

The remote control signals may be

different for some components or

functions. In this case, programme the

remote control signals with the

Learning function (page 16). Note,

however, that components and

functions that do not support the

remote control of infrared signals will

not work with this Commander.

16

GB

Example: To programme the N

(Play) signal of your video

cassette recorder to the VCR N

(Play) button of the Commander

1 Place the RM-VL600T head

to head with your

component’s remote

control.

SET

SATDVDTV CBL

TAPE

CDVCR

1

VIDEO1

2

VIDEO2

3

AUX

4

TUNER

5

CD

6

TAPE

7

MD

8

TV

9

PHONO

0

DVD

GUIDE MENU

TOOLS

SYSTEM CONTROL

AMP

ENT

OK

ABCD

1

-/--

RETURN

ANALOG

DIGITAL

PROGRAM

1 2

2,7

3

4

about 5 – 10 cm

(2 – 4 inches) away

Remote control for

your component

RM-VL600T

Programming Signals

of Another Remote

Control — Learning

Function

To operate components or

functions which do not work even

if you set a component code

number, use the following

Learning procedure to “teach” any

of the programmable buttons of

the Commander to operate the

functions of another remote

control. You can also use the

Learning function to change the

signals of individual buttons after

setting the component code

number (page 10). It is

recommended that you make a

note of the “learned” key

functions. (It is possible to make a

note on the back of the supplied

“Component code numbers.”)

Notes

• Some specific remote control signals

may not be “learned.”

• You can also use a display monitor

for computer display (including a

built-in tuner type), if the

Commander is “learned.”

17

GB

4 Press the button on the

Commander you want to

“teach.”

The SET indicator flashes and

the selected Component Select

button lights up. (Learning

function standby)

If another signal has already

been “learned” by that

button

The SET indicator flashes

twice, and the Commander

takes no action returning to its

state after the Component

Select button was pressed in

Step 3. Either “teach” to

another free button, or clear the

already “learned” function

(page 22) and start over from

the beginning.

SET

SATDVDTV CBL

TAPE

CDVCR AMP

2 Press and hold SET for over

3 seconds.

The SET indicator flashes.

SET

SATDVDTV CBL

TAPE

CDVCR AMP

3 Press the Component Select

button for the component

whose signals are to be

“learned.”

The SET indicator flashes and

the selected Component Select

button lights up.

VCR

SET

SATDVDTV CBL

TAPE

CDVCR AMP

SET

Continued

18

GB

Programming Signals of Another

Remote Control — Learning

Function (continued)

5 Press and hold the button

on the other remote control,

until both the SET indicator

and the Component Select

button light up again.

During data transfer, only the

SET indicator stays lit, and the

Component Select button turns

off.

After data transfer is complete,

the Commander returns to its

state in Step 3.

If the SET indicator flashes

five times

It means that “learning” is

incomplete. Repeat steps 4 and 5.

6 Repeat Steps 4 and 5 to

“teach” functions to other

buttons.

To “teach” another

component’s remote control

signal

After positioning the two remote

commanders as in Step 1 on page

16, press the corresponding

Component Select button, and then

follow Steps 4 and 5 to perform

Learning.

7 Press SET to finish setting.

SET SET

VCR VCR

during data

transfer

data transfer

complete

Notes

• If you do not perform Learning steps

within 20 seconds at any point during

the process, Learning mode ends.

• If you do not perform Step 5 within

10 seconds after Step 4, the learning

procedure returns to Step 3. Repeat

Step 4 while the Component Select

button lights.

To cancel setup, press SET.

If the Commander does not

seem to be working

If the “learned” button does not

operate properly, “teach” once again.

(For example, if the volume becomes

very loud after pressing 2 + only

once, noise may have interfered during

the Learning procedure.)

If you set a component code

after “learning” a signal

If you have programmed any signal on

a button by the Learning function, that

signal will work even after you set a

component code.

Note on the REC z signal

You can only “teach” to one button at a

time. Therefore you cannot teach a

sequential button operation (for

example REC z + B) to a single button

on the Commander. In this case,

“teach” the functions of each button on

your component to the Commander.

remote control

of component

19

GB

Continued

When you “teach” signals to 2

+/– or %

•If you used the Learning

function to programme the 2 +/

–

or % buttons to send any

signal to components other than

the TV or AMP, that signal will

be transmitted only by pressing

2 +/– or % when you select

that component.

•If you used the Learning

function to programme the 2 +/

–

or % buttons to send any

signal to the TV or AMP, that

signal will be transmitted only

after you select TV or AMP.

When you select other

components, the “learned”

signal will be transmitted.

To “teach” the signals for an

air-conditioner

See “Notes on programming the

signals for an air-conditioner” on

page 24.

For accurate Learning

•Do not move the remote units

during the Learning procedure.

•Be sure to keep holding down

the “learning” button until your

Commander reacts as described.

•Use fresh batteries in both

remote units.

•Avoid Learning in places subject

to direct sunlight or a strong

fluorescent light. (Noise may

interfere during the Learning

procedure.)

•The remote control detector area

may differ depending on each

remote unit. If Learning does not

work, try changing the positions

of the two remote control units.

•When you teach signals of an

interactive signal exchange

system remote control unit

(supplied with some of Sony’s

amplifiers) to the Commander,

the response signal of the main

unit may interfere with the

learning of the Commander. In

such a case, move to a place

where the signals will not reach

the main unit (e.g. other rooms,

etc.).

IMPORTANT

Be sure to place the

Commander out of the reach of

small children or pets, and lock

the controls using the Hold

function (page 34).

Components such as air -

conditioners, heaters, electric

appliances, and electric

shutters or curtains receiving

an infrared signal can be

dangerous if misused.

20

GB

2 Press and hold the

Component Select button

for the component whose

signals are to be “learned”

for over 3 seconds.

To teach signals to the SYSTEM

CONTROL buttons, press and

hold the desired SYSTEM

CONTROL button for over 3

seconds.

Both the SET indicator and the

selected Component Select

button light up.

When you “teach” signals to

the SYSTEM CONTROL

buttons, only the SET indicator

lights up.

When the SET indicator lights

up, you can release the

Component Select button. The

SET indicator flashes and the

selected Component Select

button lights up (Learning

function standby).

When you “teach” signals to

the SYSTEM CONTROL

buttons, you can release the

SYSTEM CONTROL button

when the SET indicator lights

up. The SET indicator lights

up, but the SYSTEM

CONTROL button does not

light up.

DVD

SET

SATDVDTV CBL

TAPE

CDVCR AMP

SET

SATDVDTV CBL

TAPE

CDVCR AMP

Programming Signals of Another

Remote Control — Learning

Function (continued)

Programming remote

control signals to the

Component Select buttons

and System Control

buttons

You can “teach” one operating

procedure to a Component Select

button and System Control

buttons, so that when you press

the Component Select button and

System Control buttons, the

operation is also automatically

done.

For example, if it is necessary to

switch the input selection of an

amplifier to DVD when you use a

DVD player, “teach” an input

select signal to the DVD button.

After “learning,” the input

selection of an amplifier is

automatically switched to DVD

just by pressing DVD. (For this

operation, the amplifier should

first be turned on.)

Example: To “teach” the DVD

input remote control signal of

your amplifier to the DVD

Component Select button of the

Commander

1 Follow Steps 1 to 2 (page

16).

La page charge ...

Sony RM-VL600T Le manuel du propriétaire

Sony RM-VL600T Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents