WAC Lighting R4ERAR, R6ERAR Mode d'emploi

  • Bonjour! Je suis votre assistant. J'ai examiné attentivement les instructions d'installation du luminaire LOTOS R4ERAR et R4ESAR. Le document décrit en détail comment installer en toute sécurité le luminaire, en respectant les normes électriques, et vous explique comment utiliser sa fonction de variation de lumière ELV/TRIAC et de réglage de la température de couleur pour les modèles CS. Je suis prêt à répondre à vos questions sur l'appareil.
  • Qui doit installer ce système?
    Quel type de variation est compatible avec ce luminaire?
    Que dois-je faire avant de commencer l'installation?
    Quelle est l'épaisseur du plafond pour installation ?
1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. APRIL, 2023
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
LOTOS - Fire Rated
R4ERAR
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting off the electricity.
Read all instructions before installing.
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch “OFF” the
circuit breaker switch(es) that control the power to the fixture or room that you are working on.
Place the wall switch in the “OFF” position.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
Lisez toutes les instructions avant d’installer.
Système est destiné à être installé par un électricien qualifié en onformité avec le code national de l’électricité et les règlements locaux.
Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).
Placez l’interrupteur mural en position d’arrêt (« OFF »).
CAUTION
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or
broken. Failure to follow could invalidate the ETL/cETL listing of this fixture.
OVERALL DIMENSIONS
SPECIFICATIONS
Input: 120-277V
Installation: IC for all models
Dimming: ELV / TRIAC
R4ERAR
2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. APRIL, 2023
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
LOTOS - Fire Rated
R4ERAR, R4ESAR
INSTALLATION
1. At the point of installation, cut a Ø4" round hole (See FIG. 1).
2. Ceiling thickness range is ½” to 1w”.
3. Take out fixture from packaging box.
4. Pull building supply wires through the ceiling cutout and open fixture junction box door. (See FIG. 2)
Remove desired housing knockout and feed building wires into housing using appropriate connector.
5. Connect fixture wires to building wires (See FIG. 3):
Connect each supply wire with appropriate junction box wire connector. This fixture features electronic low voltage (ELV) or TRIAC
dimming capabilities.
To utilize ELV or TRIAC, wire black (line hot), white (line neutral) and green (ground) in accordance to dimmer specifications. When
not using a dimmer, connect black fixture wire to hot, white fixture wire to neutral and green fixture wire to ground. Leave all other
wires capped individually.
6. For CS models, select your desired Color Temperature by setting the
sliding switch to the Target CCT (See FIG. 6).
Place all wiring and connectors back in driver box and replace the box’s cover.
8. Fold fixture torsion springs inward and insert trim assembly into ceiling cutout. Be sure once installed, trim assembly is flush and secure
(See FIG. 5).
FIG. 1 FIG. 2
FIG. 4
FIG. 3
FIG. 5
ROUND CUT OUT
R4ERAR : Ø4"
Black Hot
Green Ground
White Neutral
Power supply
Cable to fixture
7. Insert driver box through the mounting hole and secure to ceiling joist. (See FIG. 4).
9. Press on the front of the rotatable lens and adjust to your desired beam direction.
2700K
3000K
3500K
4000K
5000K
FIG. 6
1/2