GEAppliaces.com
Refrigerators
Top-Freezer
197D8622P002 49-60656 -1 06-11 GE
Safety Instructions . . . . . . .2, 3
Operating Instructions
Automatic Icemaker . . . . . . . . . . . . . .5
Care and Cleaning . . . . . . . . . . . . . . .6
Energy Smart Models . . . . . . . . . . . .3
Shelves . . . . . . . . . . . . . . . . . . . . . . . .4
Storage Drawers . . . . . . . . . . . . . . .4, 5
Temperature Controls . . . . . . . . . . . .4
Installation Instructions
Preparing to Install
the Refrigerator . . . . . . . . . . . . . . . . .7
Reversing the Door Swing . . . . .11–14
Water Line Installation . . . . . . . . .8–10
Troubleshooting Tips
Before You Call For Service . . . . .16, 17
Normal Operating Sounds . . . . . . . .16
Consumer Support
Consumer Support . . . . . . Back Cover
Product Registration
(Canadian) . . . . . . . . . . . . . . . . . 20, 22
Product Registration (U.S.) . . . . 19–21
Warranty for
Canadian Customers . . . . . . . . . . . 18
Warranty for U.S. Customers . . . . . 22
Réfrigérateurs
Congélateur supérieur
Refrigeradores
Congelador superior
Models 16,17,18
Manuel d’utilisation
et d’installation
Owner’s Manual and
Installation Instructions Manual del propietario
e instalación
La section française commence à la page 23 La sección en español empieza en la página 45
Write the model and serial
numbers here:
Model # __________________________
Serial # __________________________
You can find them on a label on
the upper left side of the fresh food
compartment.
Refrigerators
Top-Freezer
Mesures de sécurité . . . . 23–24
Instructions de
fonctionnement
Bacs de rangement . . . . . . . . . . .26, 27
Clayettes . . . . . . . . . . . . . . . . . . .25, 26
Energy Smart Models . . . . . . . . . 24
Commandes de
la température . . . . . . . . . . . . . . . . .25
Entretien et nettoyage . . . . . . . . . . .28
Machine à glaçons
automatique . . . . . . . . . . . . . . . . . . .27
Instructions d’installation
Installation de la
conduite d’eau . . . . . . . . . . . . . .30–33
Inversion de
l’ouverture des portes . . . . . . . . .34–38
Préparation à l’installation
du réfrigérateur . . . . . . . . . . . . . . . .29
En cas de panne
Avant d’appeler
un réparateur . . . . . . . . . . . . . . . .41, 42
Bruits normaux
de fonctionnement . . . . . . . . . . . . . .40
Soutien au consommateur
Garantie . . . . . . . . . . . . . . . . . . . . . .43
Soutien au consommateur . . . . . . . .44
Información de seguridad 45–46
Instrucciones de operación
Control . . . . . . . . . . . . . . . . . . . . . . . . .47
Cuidado y limpieza . . . . . . . . . . . . . . .50
Energy Smart Models . . . . . . . . . . . 48
Estantes . . . . . . . . . . . . . . . . . . . . . .47, 48
Gavetas de
almacenamiento . . . . . . . . . . . . . . .48, 49
Máquina de
hielos automática . . . . . . . . . . . . . . . . . .49
Instrucciones para la
instalación
Cómo invertir el
vaivén de la puerta . . . . . . . . . . . . .57–58
Instalación de la
tubería del agua . . . . . . . . . . . . . . . .52–56
Preparación para
instalar el refrigerador . . . . . . . . . . . . . .51
Consejos para la solución
de problemas
Antes de solicitar un servicio 60, 61
Sonidos normales de operación 60
Soporte al consumidor
Garantía . . . . . . . . . . . . . . . . . . . . . . . .64
Soporte al consumidor . . . . . . . . . . . . .65
Escriba aquí el modelo y el número
de serie:
Modelo # ________________________
Serie # __________________________
Encuentre estos números en la etiqueta en el
lado izquierdo de la parte superior del
compartimiento del refrigerador.
Écrivez ici le numéro de modèle et le
numéro de série :
Modèle #__________________________
Série # __________________________
Vous les trouvez sur une étiquette
dans le coin supérieur gauche du
compartiment réfrigérateur.
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could damage
the refrigerator and seriously injure themselves.
Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
In refrigerators with automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating element
located on the bottom of the icemaker. Do not place
fingers or hands on the automatic icemaking
mechanism while the refrigerator
is plugged in.
Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
Unplug the refrigerator before cleaning and making
repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
Turning the control to the 0position does
not remove power to the light circuit.
Do not refreeze frozen foods which have
thawed completely.
DANGER! RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems of
the past. Junked or abandoned refrigerators are still
dangerous…even if they will sit for “just a few days.” If
you are getting rid of your old refrigerator, please follow
the instructions below to help prevent accidents.
Before You Throw Away Your Old
Refrigerator or Freezer:
Take off the doors.
Leave the shelves in place so that children may not
easily climb inside.
Refrigerants
All refrigeration products contain refrigerants, which
under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the company
handling the disposal about what to do.
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING. GEAppliaces.com
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the
possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
The refrigerator should always be plugged into its own
individual electrical outlet which has a voltage rating that
matches the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a
fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the power
cord. Always grip plug firmly and pull straight out from
the outlet.
Repair or replace immediately all power cords that have
become frayed or otherwise damaged. Do not use a cord
that shows cracks or abrasion damage along its length or
at either end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or
a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet
and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
About Energy Smart™ Models
What Energy Smart™ Does
If the ACM (Appliance Communication
Module) is connected to your refrigerator and
is receiving utility rate information, then the
Energy Smart™ feature alters the
performance of the refrigerator. It minimizes
energy consumption when directed by the
Nucleus energy manager (sold separately) or
Smart Meter. This feature can cause changes
in the refrigerator or freezer compartment
temperatures and can cause changes in rate
of ice cube production.
Energy Smart™ Override
Press and hold the Energy Smart™ button
for 3 seconds to override the Energy
Smart™ feature. The adjacent LED will
flash three times to confirm a successful
override of the feature. This will prevent the
feature from altering the performance of
your refrigerator for 18 hours. During this
18 hour period, the LED will remain OFF.
Eighteen hours after the feature has been
disabled, the Energy Smart™ feature will
return to its normal operating routine.
Energy SmartTM Switch
Models with the EnergySmart ™ feature
have an additional button and LED light on
the controls as shown. The LED will be ON
during high rate periods and OFF during
low or normal rate periods. The button is
used to disable the EnergySmart ™ feature
(see “EnergySmart ™ override” section).
3
About the temperature control dial.
Turning the dial to Off stops cooling in both compartments—fresh food and freezer. It does not shut off power to the refrigerator.
About the fresh food compartment shelves.
Shelf supports at various levels allow you to custom-space your shelves. Not all features are on all models.
Full-Width Shelves
Some models have a steel wire sliding shelf, a
stationary tempered glass shelf,
a spillproof shelf or two steel wire stationary
shelves. These shelves can be moved to
another place in the fresh food
compartment.
The full-width sliding shelf has stop-locks.
When placed correctly on the shelf supports,
the shelf will stop before coming completely
out of the refrigerator and will not tilt when
you place food on it or remove food from it.
Half-Width Shelves
One end of the shelf rests on a molded side-
wall support; a bracket on the other end hooks
into a track on the rear cabinet wall.
To remove, lift the shelf up at front, then off
the support and out of the track.
To replace, select desired shelf height. With
shelf front raised slightly, hook the bracket’s top
lug into the track, then lower the shelf onto the
support.
NOTE: The shelf to the right of the track is designed
to hook into the right-hand slot; the shelf to the left
is designed to hook into the left-hand slot.
2
1Tilt up
To remove a full-width shelf when
the fresh food compartment door
cannot be opened fully
Lift rear
Pull forward and down
Lift rear
Pull forward
To remove the full-width shelves
About the freezer compartment shelves.
Step Shelf (on some models)
To remove the step shelf:
Lift left side of shelf slightly.
Move shelf to the left to free its right ends
from holes in the cabinet wall.
Lower right side of shelf, move shelf to the
right and take it out.
3
2
1
To replace the step shelf:
With shelf tilted as shown, fit left ends of
shelf into holes in cabinet wall. Lift left side of shelf slightly, swing shelf up,
fit right ends of shelf into holes in cabinet
wall, and lower shelf into place.
2
1
123
4
Temperature Control Dial
The temperature dial adjusts refrigerator from warmest to coldest.
See illustrations below for temperature setting information.
OFF
OFF
OFF
Recommened
factory setting Coldest setting Warmest setting
About the automatic icemaker.
A newly-installed refrigerator may take 12 to 24 hours to begin making ice.
Automatic Icemaker (on some models)
The icemaker will produce approximately
100–130 cubes in a 24-hour period, depending on
the freezer compartment temperature, room
temperature, number of door openings and other
use conditions.
If the refrigerator is operated before the water
connection is made to the icemaker, move the
feeler arm to the STOP (up) position.
When the refrigerator has been connected to
the water supply, move the feeler arm to the ON
(down) position.
You will hear a buzzing sound each time the
icemaker fills with water.
The icemaker will fill with water when it cools to
15°F. A newly-installed refrigerator may take 12 to
24 hours to begin making ice cubes.
Throw away the first few batches of ice to allow
the water line to clear.
Be sure nothing interferes with the sweep of the
feeler arm.
When the bin fills to the level of the feeler arm,
the icemaker will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes will
become cloudy, taste stale and shrink.
NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle multiple
times when making one batch of ice.
Icemaker Accessory Kit
If your refrigerator did not already come equipped
with an automatic icemaker, an icemaker
accessory kit is available at extra cost.
Check the back of the refrigerator for
the specific icemaker kit needed for
your model.
Feeler Arm in
the STOP
(up) position
Feeler Arm in
the ON (down)
position
5
About storage drawer and cover removal.
Not all features are on all models.
Twin Drawer Shelf
To remove:
Remove the drawers.
Reach in, push the front of glass cover up,
and at the same time, pull it forward as far
as it will come.
Tilt it and take it out. Avoid cleaning the cold glass
cover with hot water because the extreme
temperature difference may cause it to break.
Remove the drawer frame. (Always remove
the glass cover before you take out the
drawer frame.)
Lift the frame off the supports at each side and
back, pull it forward, tilt it and take it out.
To replace:
Lower the frame until it rests on the
supports at each side and back.
Replace the glass cover, pushing its rear
edge firmly into the rear frame channel and
gently lowering the front into place.
Replace the drawers.
3
2
1
3
2
1
Drawer and Cover Removal
Drawers can be removed easily by grasping the sides and lifting up slightly while pulling drawers
past the stop location.
To remove the cover, lift it off its supports, pull it forward, tilt it and take it out.
Adjustable Humidity Drawer (on some models)
Slide the control all the way to the
HIGH setting to provide high humidity
recommended for most vegetables.
Slide the control all the way to the LOW
setting to provide lower humidity levels
recommended for most fruits.
The snacks drawer can
be moved to the most
useful location for your
family’s needs.
Snacks Drawer
Not all features are on all models.
About the storage drawers. GEAppliaces.com
Fruit and Vegetable Drawers
Excess water that may
accumulate in the bottom of
the drawers should be emptied
and the drawers wiped dry.
Care and cleaning of the refrigerator.
6
Cleaning the Outside
The door handles and trim (on some models). Clean
with a cloth dampened with soapy water. Dry with a
soft cloth.
Keep the outside clean. Wipe with a clean cloth lightly
dampened with kitchen appliance wax or mild liquid dish
detergent. Dry and polish with a clean,
soft cloth.
The stainless steel panels and door handles (on some models)
can be cleaned with a commercially available stainless steel
cleaner. Do not use appliance wax or polish on the stainless
steel.
Do not wipe the refrigerator with a soiled dish cloth or wet
towel. These may leave a residue that can erode the paint.
Do not use scouring pads, powdered cleaners, bleach or cleaners
containing bleach because these products can scratch and
weaken the paint finish.
Cleaning the Inside
To help prevent odors, leave an open box of baking soda in
the fresh food and freezer compartments.
Unplug the refrigerator before cleaning.
If this is not practical, wring excess moisture out of sponge
or cloth when cleaning around switches, lights or controls.
Use warm water and baking soda solution—about a
tablespoon (15 ml) of baking soda to a quart (1 liter)
of water. This both cleans and neutralizes odors. Rinse and
wipe dry.
After cleaning the door gaskets, apply a thin layer of
petroleum jelly to the door gaskets at the hinge side. This
helps keep the gaskets from sticking and bending out of
shape.
Avoid cleaning cold glass shelves (on some models) with hot water
because the extreme temperature difference may cause them to
break. Handle glass shelves carefully. Bumping tempered glass can
cause it to shatter.
Do not wash any plastic refrigerator parts in the dishwasher.
Condenser
There is no need for routine condenser cleaning in normal
home operating environments.
However, in environments that
may be particularly dusty or
greasy, the condenser should
be cleaned periodically for
efficient refrigerator operation.
To clean the condenser, turn the temperature control dial to
0. Sweep away or vacuum up dust.
For best results, use a brush specially designed for this
purpose. It is available at most appliance parts stores.
Moving the Refrigerator
Be careful when moving the refrigerator away from
the wall. All types of floor coverings can be damaged,
particularly cushioned coverings and those with embossed
surfaces.
Turn the leveling legs at each front corner of the refrigerator
counterclockwise until the rollers support
the refrigerator. Pull the refrigerator straight out and return it to
position by pushing it straight in. Moving
the refrigerator in a side direction may result in damage
to the floor covering or refrigerator.
When pushing the refrigerator back, make sure you don’t roll over
the power cord or icemaker supply line (on some models).
After rolling the refrigerator back into place, turn the legs
clockwise until the legs again bear the weight of the
refrigerator.
Light Bulb Replacement
To replace a burned-out bulb, unplug the refrigerator from
its electrical outlet, unscrew the bulb when cool and replace
it with an appliance bulb of the same or lower wattage.
Turning the control to the 0position does not remove power to
the light circuit.
Preparing for Vacation
For long vacations or absences, remove food and unplug the
refrigerator. Move the temperature control dial to the 0
position, and clean the interior with a baking soda solution
of one tablespoon (15 ml) of baking soda to one quart (1
liter) of water. Leave the doors open.
Move the feeler arm to the STOP (up) position and
shut off the water supply to the refrigerator.
If the temperature can drop below freezing, have a qualified
servicer drain the water supply system (on some models) to
prevent serious property damage
due to flooding.
Preparing to Move
Secure all loose items such as grille, shelves and drawers by
taping them securely in place to prevent damage.
Be sure the refrigerator stays in an upright position during moving.
Cleaning the condenser coils.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT – Save these
instructions for local inspector’s use.
•IMPORTANT – Observe all
governing codes and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
•Note to Consumer – Keep these instructions
for future reference.
•Skill level – Installation of this appliance requires
basic mechanical skills.
•Completion time – Refrigerator Installation
15 minutes
Reversing the Door Swing
1 hour
•Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not
covered under the Warranty.
• Do not install the refrigerator where the temperature will go
below 60°F (16°C) because it will not run often enough to
maintain proper temperatures.
• Install it on a floor strong enough to support it fully loaded.
REFRIGERATOR LOCATION
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
• Sides 3/4”(19 mm)
• Top 1”(25 mm)
• Back 2”(50 mm)
CLEARANCES
Leveling legs near each front corner of the refrigerator are
adjustable. They firmly position the refrigerator and prevent
it from moving when the doors are opened. Leveling legs
should be set so the front of the refrigerator is raised just
enough that the doors close easily when opened about
halfway.
Turn the leveling legs clockwise to raise the refrigerator,
counterclockwise to lower it.
Rollers next to the leveling legs allow you to move the
refrigerator away from the wall for cleaning.
Turn the legs counterclockwise until the weight of the
refrigerator is transferred from them to the rollers. After
rolling the refrigerator back into place, turn the legs
clockwise until the legs again bear the weight of the
refrigerator.
ROLLERS AND LEVELING LEGS
If the refrigerator has an icemaker, it will have to be
connected to a cold water line. A water supply kit
(containing copper tubing, shutoff valve, fittings and
instructions) is available at extra cost from your dealer, by
visiting our Website at GEAppliaces.com (in Canada at
www.geappliances.ca) or from Parts and Accessories,
1.800.661.1616.
WATER SUPPLY TO THE ICEMAKER
(on some models)
7
Installation Instructions Models 16, 17, 18
If you have questions, call 1.800.GE.CARES or visit our Website at: GEAppliaces.com
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
8
WHAT YOU WILL NEED
•Copper or GE SmartConnect™Refrigerator
Tubing kit, 1/4”outer diameter to connect the
refrigerator to the water supply. If using copper, be sure
both ends of the tubing are cut square.
To determine how much tubing you need: measure the
distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add 8’
(2.4 m). Be sure there is sufficient extra tubing
(about 8’[2.4 m] coiled into 3 turns of about 10”
[25 cm] diameter) to allow the refrigerator to move out
from the wall after installation.
INSTALLING THE WATER LINE (ON SOME MODELS)
Installation Instructions
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of tubing
you need. Approved plastic water supply lines are GE
SmartConnect™Refrigerator Tubing (WX08X10006,
WX08X10015 and WX08X10025).
When connecting your refrigerator to a GE Reverse
Osmosis Water System, the only approved installation is
with a GE RVKit. For other reverse osmosis water systems,
follow the manufacturer’s recommendations.
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and lead
to water leakage or flooding. Call a qualified plumber to
correct water hammer before installing
the water supply line to the refrigerator.
To prevent burns and product damage, do not hook up the
water line to the hot water line.
If you use your refrigerator before connecting the water
line, make sure the feeler arm is in the STOP (up) position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power drill)
during installation, be sure the device is double insulated or
grounded in a manner to prevent the hazard of electric
shock, or is battery powered.
All installations must be in accordance with local plumbing
code requirements.
1
WHAT YOU WILL NEED (CONT.)
GE SmartConnect™Refrigerator Tubing Kits are available
in the following lengths:
6’ (1.8 m) – WX08X10006
15’ (4.6 m) – WX08X10015
25’ (7.6) m) – WX08X10025
Be sure that the kit you select allows at least 8’(2.4 m) as
described above.
NOTE: The only GE approved plastic tubing is
that supplied in GE SmartConnect™Refrigerator
Tubing kits. Do not use any other plastic water
supply line because the line is under pressure at
all times. Certain types of plastic will crack or
rupture with age and
cause water damage to your home.
•A GE water supply kit (containing tubing, shutoff
valve and fittings listed below) is available at extra cost
from your dealer or from Parts and Accessories,
1.800.661.1616.
•A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4–8.1 bar).
•Power drill.
•1/2”or adjustable wrench.
•Straight and Phillips
blade screwdriver.
•Two 1/4”outer diameter compression nuts and
2 ferrules (sleeves)—to connect
the copper tubing to the shutoff
valve and the refrigerator water valve.
OR
•If you are using a GE SmartConnect™Refrigerator
Tubing kit, the necessary fittings are preassembled
to the tubing.
•If your existing copper water line has a flared fitting at
the end, you will need an adapter (available at plumbing
supply stores) to connect the water line to the refrigerator
OR you can cut off the flared fitting
with a tube cutter and then use a compression fitting.
Do not cut formed end from GE SmartConnect™
Refrigerator tubing.
•Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32”at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
Installation Instructions
Install the shutoff valve on the nearest frequently used drinking water line.
SHUT OFF THE MAIN WATER
SUPPLY AND UNPLUG
REFRIGERATOR
Turn on the nearest faucet (counterclockwise) long
enough to clear the line of water.
1
9
Choose a location for the valve that is easily accessible. It
is best to connect into the side of a vertical water pipe.
When it is necessary to connect into a horizontal water
pipe, make the connection to the top or side, rather than
at the bottom, to avoid drawing off any sediment from
the water pipe.
Drill a 1/4”hole in the water pipe (even if using a self-
piercing valve), using a sharp bit. Remove any burrs
resulting from drilling the hole in the pipe. Take care
not to allow water to drain into the drill. Failure
to drill a 1/4”hole may result in reduced ice
production or smaller cubes.
DRILL THE HOLE FOR THE VALVE
2
Fasten the shutoff valve to the cold water pipe with the
pipe clamp.
Tighten the clamp screws until the sealing washer begins
to swell.
NOTE: Do not overtighten or you may crush the
tubing.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts. Consult
with your licensed plumber.
FASTEN THE SHUTOFF VALVE
3
Washer
Inlet End
Clamp Screw
Vertical Cold
Water Pipe
Saddle-Type
Shutoff Valve
Pipe Clamp FLUSH OUT THE TUBING
Turn the main water supply on (counterclockwise) and
flush out the tubing until the water is clear.
Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed through the
tubing.
6
CONNECT THE TUBING
TO THE VALVE
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutoff valve.
Make sure the tubing is fully inserted into the
valve. Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then tighten one
additional turn with a wrench. Overtightening may
cause leaks.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts. Consult
with your licensed plumber.
5
Saddle-Type
Shutoff Valve
Compression
Nut
SmartConnect™
Tubing
Packing Nut
Outlet Valve Ferrule (sleeve)
ROUTE THE TUBING
Route the tubing between the cold water line and the
refrigerator.
Route the tubing through a hole drilled in the wall or
floor (behind the refrigerator or adjacent base cabinet) as
close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing (about 8
feet [244 cm] coiled into 3 turns of about 10”[25 cm]
diameter) to allow the refrigerator to move out from the
wall after installation.
4
CONNECT THE TUBING TO THE
REFRIGERATOR (CONT.)
Fasten the tubing into the clamp provided to
hold it in a vertical position. You may need to
pry open the clamp.
7
Installation Instructions
10
CONNECT THE TUBING TO THE
REFRIGERATOR
NOTES:
•Before making the connection to the refrigerator, be
sure the refrigerator power cord is not plugged into the
wall outlet.
•We recommend installing a water filter if your water
supply has sand or particles that could clog
the screen of the refrigerator’s water valve. Install
it in the water line near the refrigerator. If using
GE SmartConnect™Refrigerator Tubing kit,
you will need an additional tube (WX08X10002)
to connect the filter. Do not cut plastic tube to
install filter.
Remove the access cover.
Remove the plastic flexible cap from the water
valve (refrigerator connection).
Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown. On GE
SmartConnect™Refrigerator Tubing kit,
the nuts are already assembled to the tubing.
Insert the end of the tubing into the water valve
connection as far as possible. While holding the tubing,
tighten the fitting.
For plastic tubing from a GE SmartConnect™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then
tighten one additional turn with a wrench.
Overtightening may cause leaks.
7
TURN THE WATER
ON AT THE
SHUTOFF VALVE
Tighten any connections
that leak.
8
Tubing Clamp
1/4”Compression
Nut
Ferrule
(sleeve)
SmartConnect™
Tubing
Refrigerator
Connection
1/4” Copper
Tubing
PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the wall.
Push the refrigerator back to the wall.
9
Move the feeler arm to the ON (down) position. The
icemaker will not begin to operate until it reaches
its operating temperature of 15°F (–9°C) or below.
It will then begin operation automatically.
START THE ICEMAKER
Feeler Arm in the
STOP (up) position
Feeler Arm in
the ON (down) position
10
NOTE: In lower water pressure conditions, the water
valve may turn on up to 3 times to deliver enough water
to the icemaker.
Reattach the access cover.
INSTALLING THE WATER LINE (CONT.)
1
11
Installation Instructions
REVERSING THE DOOR SWING
2
When reversing the door swing:
•Read the instructions all the way through before starting.
•Handle parts carefully to avoid scratching paint.
•Set screws down by their related parts to avoid using them
in the wrong places.
•Provide a non-scratching work surface for
the doors.
IMPORTANT: Once you begin, do not move the cabinet
until door-swing reversal is completed.
These instructions are for changing the hinges from
the right side to the left side—if you ever want to change the
hinges back to the right side, follow these same instructions
and reverse all references to left and right.
IMPORTANT NOTES
Phillips screwdriver
TOOLS REQUIRED
Masking tape
T20 or T25 Torxdriver
(needed for some models)
5/16”hex-head
socket driver
5/16”open-end
wrench
Putty knife or thin-blade
screwdriver
2.1Tape the door shut with masking tape.
2.2With a 5/16”hex-head socket driver, remove the
screws that hold the top hinge to the cabinet.
REMOVE THE FREEZER DOOR
2
2.3Lift the hinge straight up to free the hinge pin from
the socket in the top of the door and set it aside,
along with its screws.
Top Hinge
2.6Transfer the 2 screws from the opposite side of the
cabinet to the screw holes vacated by the top hinge
removal.
2.5Set the door on a non-scratching surface with the
outside up.
2.4Remove the tape and tilt the door away from the
cabinet. Lift it off the center hinge pin.
1.1Unplug the refrigerator from its electrical
outlet.
1.2Empty all door shelves, including the dairy
compartment.
CAUTION: Do not let either door drop to the floor. To
do so could damage the door stop.
BEFORE YOU START
1
Installation Instructions
3.1Tape the door shut with masking tape.
REMOVE THE FRESH FOOD DOOR
3
3.4Set the door outside-up on a non-scratching surface.
3.3Remove the tape and tilt the door away from the
cabinet. Lift the door from the pin in the bottom hinge
bracket. (If the plastic washer sticks to the door bottom,
put it back on the hinge.)
3.2Using a 5/16”hex-head socket screwdriver and a
5/16”open-end wrench, remove the two screws
holding the center hinge to the cabinet. Lift the
center hinge to free its pin from the socket in the top
of the door, and set hinge and screws aside. Be
careful not to lose the center hinge spacer and washer.
3.7Take one of the screws removed in step 2 and start
it in the outermost screw hole on the opposite side. Do not
drive it all the way down—leave enough space under the
screw head for thickness of the bracket.
12
REVERSING THE HARDWARE
4
REVERSING THE DOOR SWING (CONT.)
2
3.5Transfer the two screws from the opposite side of the
cabinet to the screw holes vacated by the center hinge
removal.
3.6Transfer the washer (if your model has one) to the
opposite side.
3
REMOVE THE FRESH FOOD DOOR (CONT.)
4.1 Move the bottom hinge bracket and plastic washer from the
right side to the left side.
Plastic
Washer
Hinge
Bracket
Switch the hinge pin to the
opposite side of the bracket.
Installation Instructions
4.2Interchange hinge and screws at top right with screws at
top left of cabinet. Do not tighten screws on hinge side
at this time.
NOTES:
•Some hinges have four holes. Which holes you use
for installing the hinge depends on which side you
install the hinge.
•The outer edge of the hinge should be parallel to the
edge of the case for correct installation.
Installing the hinge on the left. Installing the hinge on the right.
REVERSING THE DOOR HANDLES
5
5.1.2 Remove the handle.
Top
5.1.3 Remove plug button from the top hinge hole on the left
side of the door and insert it into the hole on the
opposite side that was vacated by removal of the top
hinge.
Plug Button
Plug
13
5.1.4 Pull the plug button from the front of the door and
transfer it to the opposite side.
To reattach the
handle on the
opposite side.
Plug Button
5.3 Reinstall fresh food door handle
5.3.1 Attach the handle to the right side of the
door with screws at the top
and under the handle plug.
5.3.2 Reinstall the handle plug.
REVERSING THE DOOR
HANDLES (CONT.)
5
REVERSING THE HARDWARE
(CONT.)
4
5.1 Transfer fresh food door handle
5.1.1 Remove the handle plug using a tape-tipped
putty knife under the edge, and remove the
screw underneath. Remove the two screws
holding the handle to the top of the door.
5.2 Transfer door stop
5.2.1 Move the plastic door stop and screws from
the right side to the left side.
Plastic Door Stop
Left Side
Right Side
Metal Door Stop
Left Side Right Side
5.2.2 Move the metal door stop from the right side
to the left side and transfer the screw to the
opposite side of the door.
Installation Instructions
5.4.3 Remove the screw from the
right top edge of the door
and insert it into the handle
screw hole on the left side.
5.4.4 Transfer the door stop as shown in preceding
section 5.2.
5.4.5 Attach the handle to the right
edge of the door
with screws at top and bottom,
using bottom holes vacated by
removal of the door stop
screws.
TOP
BOTTOM
Top
Bottom
5.4 Transfer Freezer Door Handle
5.4.1 Remove the screw
holding the handle
to the top of the
door and the two
screws holding the
handle to the bottom
of the door.
5.4.2 Remove the handle.
14
6.1.2 Insert the pin on the center hinge into the socket in the
top of the door. Place the spacer, then the washer, on the
hinge pin.
NOTE: The center hinge must
be turned over as shown when
mounted on the left side.
Plastic Washer
and Spacer
Hinge Pin
6.2 Re-hang the freezer door
6.2.1 Lower the freezer door
onto the center hinge
pin. Be sure the
washer and spacer
are in place on the pin.
RE-HANGING THE DOORS (CONT.)
6
Center Hinge Pin
Plastic Washer
and Spacer
REVERSING THE DOOR SWING (CONT.)
2
6.1.3 Tilt the door toward the cabinet. As the door is brought
into position, slide the hinge under the head of the screw
which earlier had been partly driven into the outermost
hole. Insert the remaining screw, then tighten both screws
securely.
6.1 Re-hang the fresh food door
6.1.1 Lower the fresh food door onto the
bottom hinge pin. Be sure the washer
is in place on the pin.
RE-HANGING THE DOORS
6
Plastic
Washer
Hinge
Bracket
6.2.2 Tilt the door toward the cabinet, lifting the top hinge so
the pin fits into the socket on the top of the door.
6.2.3. Make sure the door is slightly above the top of the
cabinet and the gap between the doors is even across the
front. Tighten the top hinge screws. Do not overtighten
these screws–tighten them until they are just snug, then
turn them another one-half turn.
REVERSING THE DOOR HANDLES (CONT.)
5
15
Installation Instructions
LABEL
NOTE: The ACM can be placed on top, back, or side of refrigerator. ACM can also be
installed without direct contact with refrigerator (for example in adjoining cabinets). See
ACM manual for further ACM installation details.
PLACE ACM
3
CONNECTING ENERGY SMART APPLIANCE
3
2.1 Locate interconnect cable.
This accessory is part of ACM
kit.
2.2 Plug interconnect cable into
connector on access cover as
shown.
2.3 Plug opposite end of
interconnect cable into ACM.
2.4 Refer to ACM kit
instructions to connect ACM
to NucleusTM energy
manager or Smart Meter
CONNECT APPLIANCE TO ACM
2
REMOVE LABEL OVER INTERCONNECT CABLE CONNECTOR ON ACCESS COVER
1
REMOVE WHEN
REMOVE WHEN
CONNECTING TO ACM
CONNECTING TO ACM
16
The new high efficiency
compressor may run
faster and longer than
your old refrigerator and
you may hear a high-pitched hum or pulsating sound
while it is operating.
You may hear a whooshing sound when the doors close. This
is due to pressure equalizing within the refrigerator.
Normal operating sounds. GEAppliaces.com
Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features
and use newer technology.
You may hear the fans spinning at high
speeds.
This happens when the refrigerator is
first plugged in, when the doors are
opened frequently or when
a large amount of food is added to the refrigerator or
freezer compartments. The fans are helping to maintain the
correct temperatures.
CLICKS, POPS,
CRACKS and CHIRPS
You may hear cracking or popping sounds when the refrigerator
is first plugged in. This happens as the refrigerator cools to the
correct temperature.
The compressor may cause a clicking or chirping sound when
attempting to restart (this could take
up to 5 minutes).
Expansion and contraction of cooling coils during and after
defrost can cause a cracking or popping sound.
On models with an icemaker, after an icemaking cycle, you may
hear the ice cubes dropping into the ice bucket.
WATER SOUNDS
The flow of refrigerant through the freezer cooling coils may
make a gurgling noise like boiling water.
Water dropping on the defrost heater can cause a sizzling,
popping or buzzing sound during the defrost cycle.
A water dripping noise may occur during the defrost cycle as ice
melts from the evaporator and flows into the drain pan.
Closing the door may cause a gurgling sound due to pressure
equalization.
Do you hear what I hear? These sounds are normal.
For additional information on normal
icemaker operating sounds, see the
About the automatic icemaker section.
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem Possible Causes What To Do
Refrigerator does not Refrigerator in defrost cycle. •Wait about 30 minutes for defrost cycle to end.
operate Temperature control dial •Move the temperature control dial to a temperature
in 0 position. setting.
Refrigerator is unplugged. •Push the plug completely into the outlet.
The fuse is blown/circuit •Replace fuse or reset the breaker.
breaker is tripped.
Energy Smart™ feature is • Wait about 2 hours for normal operation to continue
altering refrigerator performance
Vibration or rattling (slight Roller screws or leveling legs •See Rollers and Leveling Legs.
vibration is normal) need adjusting.
Fresh food or freezer Temperature control dial •See About the temperature control dial.
compartment too warm not set cold enough.
Warm weather or frequent •Set the temperature control dial one step colder.
door openings. See About the temperature control dial.
Door left open. •Check to see if package is holding door open.
Package blocking air duct in •Check to see if package is blocking air duct in freezer
freezer compartment. compartment.
Energy Smart™ feature is • See About Energy Smart™ Models
altering refrigerator performance
HUMMM...
WHOOSH...
Problem Possible Causes What To Do
Normal when refrigerator •Wait 24 hours for the refrigerator to completely
is first plugged in. cool down.
Often occurs when large •This is normal.
amounts of food are
placed in refrigerator.
Door left open. •Check to see if package is holding door open.
Hot weather or frequent •This is normal.
door openings.
Temperature control dial •See About the temperature control dial.
set at the coldest setting.
Grille and condenser •See Care and cleaning.
need cleaning.
Frost or ice crystals Door left open. •Check to see if package is holding door open.
on frozen food Too frequent or too long
(frost within package door openings.
is normal)
Automatic icemaker Icemaker is not on. •Move the feeler arm to the ON (down) position.
does not work Water supply turned off or •See Installing the water line.
(on some models) not connected.
Freezer compartment •Wait 24 hours for the refrigerator to completely
too warm. cool down.
Piled up cubes in the storage •Level cubes by hand.
bin cause the icemaker
to shut off.
Frequent “buzzing” sound Icemaker is on but the water •Move the feeler arm to the STOP (up) position. Keeping it
supply to the refrigerator has on will damage the water valve.
not been connected.
Cubes too small Water shutoff valve connecting •Call the plumber to clear the valve.
refrigerator to water line may
be clogged.
Slow ice cube freezing Door left open. •Check to see if package is holding door open.
Temperature control dial •See About the temperature control dial.
not set cold enough.
Ice cubes have Ice storage bin needs cleaning. •Empty and wash bin. Discard old cubes.
odor/taste Food transmitting odor/taste •Wrap foods well.
to ice cubes.
Interior of refrigerator •See Care and cleaning.
needs cleaning.
Energy Smart™ feature is •See About Energy Smart™ Models
altering refrigerator performance
Moisture forms on Not unusual during •Wipe surface dry and reset temperature control dial
cabinet surface periods of high humidity. one setting colder.
between the doors
Moisture collects inside Too frequent or too
(in humid weather, air long door openings.
carries moisture into
refrigerator when doors
are opened)
Refrigerator has odor Foods transmitting •Foods with strong odors should be tightly wrapped.
odor to refrigerator. •Keep an open box of baking soda in the refrigerator;
replace every three months.
Interior needs cleaning. •See Care and cleaning.
Motor operates for long
periods or cycles on and
off frequently. (Modern
refrigerators with more
storage space and a larger
space and a larger freezer
require more operating
time. They start and stop
often to maintain even
temperatures.)
Before you call for service…
17
Troubleshooting Tips
18
TERMS AND CONDITIONS:
This warranty applies only for single family domestic use in
Canada when the Refrigerator has been properly installed
according to the instructions supplied by Mabe and is connected
to an adequate and proper utility service.
Damage due to abuse, accident, commercial use, and alteration or
defacing of the serial plate cancels all obligations of this
warranty.
Service during this warranty period must be performed by an
Authorized Mabe Service Agent.
Neither Mabe nor the Dealer is liable for any claims or damages
resulting from failure of the Refrigerator or from service delays
beyond their reasonable control.
To obtain warranty service, purchaser must present the original
Bill of Sale. Components repaired or replaced are warranted through
the remainder of the original warranty period only.
This warranty is extended to the original purchaser and any
succeeding owner for products purchased for home use within
Canada. In home warranty service will be provided in areas where it
is available and deemed reasonable by Mabe to provide.
This warranty is in addition to any statutory warranty.
WHAT IS NOT COVERED:
• Owner is responsible to pay for service calls related to product
installation and/or teaching how to use the product.
• Damage to finish must be reported within 48 hours following
the delivery of the appliance.
• Damage to finish after delivery.
• Improper installation—proper installation includes adequate air
circulation to the refrigeration system, adequate electrical,
plumbing and other connecting facilities.
• Replacement of house fuses or resetting of circuit breakers.
• Replacement of light bulbs.
• Damage to product caused by accident, fire, floods or acts
of God.
• Loss of food due to spoilage.
• Proper use and care of product as listed in the owner’s manual,
proper setting of controls.
• Product not accessible to provide required service.
• Warrantor is not responsible for consequential damages.
IMPORTANT
Keep this warranty and your bill of sale as proof of original purchase and purchase date.
Please have serial number and model number available when calling for service.
Mabe Service is available coast to coast. If further help is
needed concerning this warranty, contact:
Manager, Consumer Relations
Mabe Canada Inc., Consumer Service
1 Factory Lane, Suite 310
Moncton, New Brunswick E1C 9M3
1.800.561.3344
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
What is covered How Long Warranted Parts Labour
(From Date of Sale) Repair or Replace
at Mabe’s Option
Compressor GE Profile: Ten (10) Years GE Profile: Ten (10) Years GE Profile: Five (5) Years
GE and All Other GE and All Other GE and All Other
Brands: One (1) Year Brands: One (1) Year Brands: One (1) Year
Sealed System (including GE Profile: Five (5) Years GE Profile: Five (5) Years GE Profile: Five (5) Years
evaporator, condenser GE and All Other GE and All Other GE and All Other
tubing and refrigerant) Brands: One (1) Year Brands: One (1) Year Brands: One (1) Year
All Other Parts One (1) Year One (1) Year One (1) Year
CUSTOMER WARRANTY
(for customers in Canada)
Your refrigerator is warranted to be free of defects in material and workmanship.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,
are limited to one year or the shortest period allowed by law.
19
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Important: If you did not get a registration card with your
product, detach and return the form on the next
page to ensure that your product is registered, or
register online at GEAppliaces.com. The top card
is for products installed in the U.S. The bottom
card is for products installed in Canada.
123
Model Number Serial Number
Complete and mail
your Consumer
Product
Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in
the
unlikely event of
a
safety modification.
After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
800 GE CARES
(800.432.2737).
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
GE Service Protection Plus™
GE, a name recognized worldwide for quality and dependability together with Assurant Solutions, offers you
Service Protection Plus™—comprehensive protection on your appliances.*
Benefits Include:
• Prompt, reliable service from GE Authorized Servicers
• Convenient hours designed to suit your busy schedule
• Quality replacement parts
• The dependability of GE, a name recognized and trusted worldwide
• Ask about our interest-free payment plans
With Service Protection Plus you can expect:
• An extended service plan that limits unexpected repair bills
• Service coverage for most major brands
• Unlimited service calls for the length of your contract, or credit toward a replacement product
• Service coverage for covered operating parts and labor on appliances and home electronics that fail during normal single family
household use
• Your satisfaction is our goal. We strive to provide you with excellent service in a professional and timely manner.
Place your confidence in GE and call us in the U.S. toll-free at 1.800.626.2224for more information.
*Most brands covered up to 15 years old in the continental U.S.
SPP is a trademark of General Electric Company.
OWNERSHIP REGISTRATION
P.O. BOX 1780
MISSISSAUGA, ONTARIO
L4Y 4G1
(FOR CANADIAN CONSUMERS ONLY)
Please place in envelope and mail to:
Veuillez mettre dans une enveloppe et envoyez à :
20
Cut here
For refrigerators installed in Canada
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
dans d''autres langues
- English: GE GTK17JCDBS User guide
- español: GE GTK17JCDBS Guía del usuario