GE GBS22LBMCC Le manuel du propriétaire

www.GEAppliances.com
Refrigerators
Bottom Freezer
162D1520P009   49-60114   A1058013 12-00 JR
Safety Information
Adapter Plugs  . . . . . . . . . . . . . . . . . . .4
Connect Electricity . . . . . . . . . . . . . . .4
Extension Cords  . . . . . . . . . . . . . . . . .3
Proper Disposal  . . . . . . . . . . . . . . . . .3
Safety Precautions  . . . . . . . . . . . . . . .2
Operating Instructions
Features  . . . . . . . . . . . . . . . . . . . . . .6, 7
Ice Service  . . . . . . . . . . . . . . . . . . . . . .8
Temperature Controls  . . . . . . . . . . .5
Care and Cleaning
Cleaning  . . . . . . . . . . . . . . . . . . . .9, 10
Light Bulbs  . . . . . . . . . . . . . . . . . . . .10
Installation Instructions
Preparing to Install 
the Refrigerator  . . . . . . . . . . . . .11, 12
Reversing the Door Swing  . . . .12–18
Troubleshooting Tips
Before You Call For Service  . . .19, 20
Normal Operating Sounds  . . . . . . .19
Consumer Support
Consumer Support . . . . . .Back Cover
Warranty for Canadian 
Customers  . . . . . . . . . . . . . . . . . . . . .21
Warranty for U.S. Customers  . . . . .22
Réfrigérateurs
Congélateur inférieur
Refrigeradores
Congelador inferior
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on a label on the 
left side, near the top of the refrigerator
compartment.
Model 22
Manuel d’utilisation 
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario
y instalación
La section française commence à la page 24
La sección en español empieza en la página 46

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

that releases the cubes. Do not place fingers or

hands on the automatic icemaking mechanism

while the refrigerator is plugged in.

■

■Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■Turning the control to the

OFF

position does

not remove power to the light circuit.

■

■Do not refreeze frozen foods which have

thawed completely.

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

2

3

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may

not easily climb inside.

CFC Disposal

Your old refrigerator has a cooling system that used

CFCs (chlorofluorocarbons). CFCs are believed to

harm stratospheric ozone.

If you are throwing away your old refrigerator, make

sure the CFC refrigerant is removed for proper

disposal by a qualified servicer. If you intentionally

release this CFC refrigerant you can be subject to

fines and imprisonment under provisions of

environmental legislation.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA certified (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

www.GEAppliances.com

4

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and

obligation to have it replaced with a properly

grounded 3-prong wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

USE OF ADAPTER PLUGS

(Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a

temporary connection

may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks,

DO NOT USE

the refrigerator until a proper ground has been

established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should

have the circuit checked by a qualified electrician to make

sure the outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

About the controls on the refrigerator.

www.GEAppliances.com

Control Settings

Refrigerator Control

The refrigerator control maintains the temperatures throughout the refrigerator.

Freezer Control

The freezer control maintains the temperatures throughout the freezer compartment.

Moving the freezer control to

OFF

stops cooling in both areas—refrigerator and freezer—but does

not shut off power to the refrigerator.

The temperature controls on your refrigerator have letters and numbers. Initially set the refrigerator control at 5

and the freezer control at C.

If you want colder or warmer temperatures, adjust the refrigerator temperature first. When satisfied with that

setting, adjust the freezer temperature.

Control settings will vary based on personal preferences, usage and operating conditions, and may require more

than one adjustment.

After changing the controls, allow 12 hours for the refrigerator to reach the temperature you have set.

cold coldest

Freezer Control

5

6

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

About the refrigerator shelves and bins.

Not all features are on all models.

Door Shelves

The bottom door shelf in the refrigerator

compartment and the freezer door shelves

are removable for easy cleaning.

To remove, hold both ends and pull

straight up.

Freezer Shelf and Basket

The freezer has two storage levels for your

frozen foods, a freezer shelf and a freezer

basket. The basket glides in and out for easy

food selection.

To remove the basket, pull it out until it

stops. Then tilt the front of the basket up

and finish pulling the basket all the way out.

To replace the basket, slide it all the way in.

Rearranging the Shelves

Shelves in the refrigerator compartment are adjustable.

To Remove To Replace

Lift up and out

2

Insert

top hook

1

Lower to

lock in place

2

Tilt up

1

Bins on the Refrigerator Door

Adjustable bins can easily be carried

from refrigerator to work area.

To remove:

Use your thumbs or forefingers

to push the lock tabs toward the center. Pull

the bin straight out.

To replace:

Slide the bin into the grooved

area until the tabs lock into place.

The divider

helps prevent tipping, spilling

or sliding of small items stored on the

door shelf. Place a finger on either side

of the divider near the front and move it

back and forth to fit your needs.

Divider

About the storage drawers.

www.GEAppliances.com

Not all features are on all models.

7

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Fruit and Vegetable Drawers

Excess water that may accumulate in the

bottom of the drawers should be emptied

and the drawers wiped dry.

Adjustable Humidity Drawers

Slide the control all the way to the

HIGH

setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the

LOW

setting to provide lower humidity levels

recommended for most fruits.

Snacks Drawer

The snacks drawer can be moved to the

most useful location for your family’s needs.

Drawer Removal

Drawers at the bottom of the refrigerator

compartment stop before coming all the

way out, to help prevent contents from

spilling onto the floor. Drawers can be

removed easily by tilting up slightly and

pulling past “stop” location.

To remove drawers when the refrigerator

compartment door cannot be opened all

the way, first remove food and shelves

above the drawers.

Remove the drawer farthest from

the door.

Remove the glass top by pushing up

from underneath and tilting it to clear

the door. Be careful when handling

the glass.We recommend wearing

protective gloves.

Lift the empty drawer frame out.

Remove the center post.

Slide the other drawer and frame over

and remove them. After cleaning,

replace the drawers in reverse order.

8

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

About the ice service.

Not all features are on all models.

Icemaker Accessory Kit

An icemaker accessory kit is available at

extra cost.

Check the label located inside the

refrigerator compartment on the

upper left side for the specific icemaker

kit needed for your model.

Ice Service Compartment

The freezer has an ice service compartment

with an ice tray shelf and a pull-out ice

storage bin. They can both be moved to

either side of the freezer.

CAUTION: Make sure shelf is secure before placing

items on shelf to avoid property damage.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Care and cleaning of the refrigerator.

www.GEAppliances.com

9

Cleaning the Outside

The door handles and trim.

Clean with a cloth

dampened with soapy water. Dry with a soft

cloth. Do not use wax on the door handles

and trim.

Keep the outside clean.

Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish

detergent. Dry and polish with a clean,

soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors,

leave an open box of

baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning.

If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use an appliance wax polish on the inside

surface between the doors.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 l) of water. This both cleans

and neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a thin

layer of petroleum jelly to the door gaskets

at the hinge side. This helps keep the gaskets

from sticking and bending out of shape.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference may

cause them to break. Handle glass shelves

carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts in

the dishwasher.

Under the Refrigerator

For most efficient operation, keep the

area under the refrigerator clean. Remove

the base grille and sweep away or vacuum

up dust.

For best results, use a brush specially

designed for this purpose. It is available at

most appliance parts stores.

Clean the condenser coils at least

once a year.

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line.

10

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Care and cleaning of the refrigerator.

Preparing for Vacation

For long vacations or absences, remove

food and unplug the refrigerator. Move the

freezer control to the

OFF

position, and

clean the interior with a baking soda

solution of one tablespoon (15 ml) of

baking soda to one quart (1 l) of water.

Leave the doors open.

Move the icemaker feeler arm (for

icemaker equipped models) to the

STOP

(up) position and shut off the water supply

to the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (for icemaker equipped

models) to prevent serious property

damage due to flooding.

Preparing to Move

Secure all loose items such as grille, shelves

and drawers by taping them securely

in place to prevent damage.

Be sure the refrigerator stays in an upright

position during moving.

Light Bulb Replacement

Light bulbs are located at the top of the

refrigerator and freezer compartments.

To replace a light bulb, unplug the

refrigerator’s power cord plug from

the wall outlet.

Freezer Light

To remove light cover, remove the 1/4″hex

head screws at the back of the cover. Slide

the cover back and remove. After replacing

with the same size bulb, reinstall the light

cover and plug in the refrigerator.

Refrigerator Light

To remove the light cover, remove the

1/4″hex head screws at the back of the

cover. Slide the cover back and remove.

After replacing with same size bulb, reinstall

light cover and plug in the refrigerator.

1/4″Hex Head Screws

Back of Freezer

Front of Freezer

Freezer Light

Refrigerator Light

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Preparing to install the refrigerator.

Read these instructions completely and carefully.

Water Supply to the Icemaker

If the refrigerator has an icemaker, it will have to be

connected to a cold water line.

A water supply kit (containing copper tubing,

shutoff valve, fittings and instructions) is available

at extra cost from your dealer or from Parts and

Accessories, 800-626-2002.

Refrigerator Location

Do not install the refrigerator where the

temperature will go below 60°F (16°C)

because it will not run often enough to maintain

proper temperatures.

Install it on a floor strong enough to support it

fully loaded.

Clearances

Allow the following clearances for ease of

installation, proper air circulation and

plumbing and electrical connections:

Sides . . . . . . . . . . . . . . . . . . . . . . . . . . .0″(0 mm)

Top . . . . . . . . . . . . . . . . . . . . . . . . . . . .1″(25 mm)

Back . . . . . . . . . . . . . . . . . . . . . . . . . . . .1″(25 mm)

Rollers

The rollers have 3 purposes:

Rollers adjust so the door closes easily when

opened about halfway. [Front of refrigerator

should be 1/4″(6 mm) higher than the rear

of refrigerator.]

Rollers adjust so the refrigerator is firmly

positioned on the floor and does not wobble.

Rollers allow you to move the refrigerator away

from the wall for cleaning.

To adjust the rollers:

Remove the base grille.

Turn the roller

adjusting screws

clockwise to raise

the

refrigerator,

counter-

clockwise to lower it.

Use a 3/8″socket

wrench or adjustable

wrench. Replace the

base grille.

Base Grille

Remove the base grille

by grasping it at the

bottom and pulling it

straight out.

To replace the base

grille, align prongs on

back of grille with slots

in cabinet and push

forward until the grille

snaps into place.

Roller Adjustment Screw

(3/8″hex with slot)

Roller

Stabilizing

Brake

11

12

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Preparing to install the refrigerator.

Read these instructions completely and carefully.

Stabilizing Brake

This refrigerator is equipped with a leveling foot

which serves as a stabilizing brake. This additional

leveling foot will hold the refrigerator securely in

position during operation and cleaning.

To set the brake,

first remove the base grille and

hinge cover. Second, adjust the rollers to the

desired position. Then turn the stabilizing brake

until the brake is firmly in place against the floor.

After the brake is securely in place, unscrew the

roller adjustment bolt counterclockwise until the

weight of the refrigerator is supported by the

stabilizing brake. This allows the weight to be

positioned on the stabilizing brake.

Reinstall the hinge cover and replace the base grille.

Reverse the procedure to roll the refrigerator out.

CAUTION: To avoid possible personal injury or property

damage the stabilizing brake must be firmly touching

the floor.

Roller Adjustment Screw

(3/8″hex with slot)

Roller

Stabilizing Brake

Bottom Hinge Cover

Reversing the door swing.

Read these instructions completely and carefully.

Before You Begin

When reversing the door swing:

■Read the instructions all the way through before starting.

■Handle parts carefully to avoid scratching paint.

■Set screws down by their related parts to avoid using them in the wrong places.

■Provide a non-scratching work surface for the doors.

IMPORTANT: Once you begin, do not move the cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from the right side to the left side—if you ever want to change the hinges

back to the right side, follow these same instructions and reverse all references to left and right.

Tools Required

■Phillips screwdriver

■Blade-type screwdriver

■Masking tape

■5/16″hex socket driver

■3/8″socket and ratchet

■T15 Torx Driver

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

13

Remove the Refrigerator Door

Remove the top hinge cover (lift up on the

outside edge and pull off).

Tape the door shut with masking tape at

both upper corners.

With 5/16″hex socket driver, remove the

3 screws that hold the top hinge to the cabinet.

Lift the hinge straight up to free the hinge pin

from the socket in the top of the door. Carefully

peel the adhesive spacer from the cabinet top

and position it over the hinge holes on the

opposite side.

Remove the tape, tilt the door away from the

cabinet and lift it to free its bottom socket from

the hinge pin on the center hinge bracket.

Set the door on a non-scratching surface.

Remove the Freezer Door

Tape the door shut with masking tape at both

upper corners.

Remove the hinge pin with a 5/16″hex socket

driver.

Remove the tape and tilt the door away from the

cabinet. Remove and save the washer on top of

the door socket.

Lift the door straight up to free its bottom socket

from the pin in the bottom hinge bracket.

If the hinge pin and washer stick in the bottom

door socket, remove them, place the pin in the

outermost hole in the bottom hinge bracket and

slip the washer over the pin.

NOTE: The hinge rod may fall out of the door. If this

happens, set the rod aside. It will be replaced later.

Washer

Freezer Door

Hinge Pin

Center

Hinge

Bracket

Adhesive spacer

Before Removing the Doors

Unplug the refrigerator from its electrical

outlet.

Empty all door shelves, including the dairy

compartment.

CAUTION: Do not let either door drop to the floor. To do so

could damage the door stop.

14

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Reversing the hardware.

Read these instructions completely and carefully.

Transfer Bottom Hinge Bracket to the Left

Remove the base grille by grasping it at both

ends and pulling it straight out.

Remove the bottom hinge bracket cover

with a flat screwdriver.

Use the ratchet wrench and socket to remove

the hex head screws and hinge bracket from

the bottom right side of the cabinet. Replace

the screws in the holes.

Remove the two outermost hex head screws

from the bottom left side of the cabinet.

Place the bottom hinge bracket over the

holes and tighten with the screws.

Move the hinge pin with the washer to the

hole that’s now on the outside.

NOTE: It is important that the washer is on the bottom

of the hinge pin.

Bottom Right

Bottom Left

Washer

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Transfer Center Hinge Bracket to the Left

Remove the hinge bracket from the center right

side of the cabinet by removing the three

Phillips head screws.

Remove the three outermost 5/16″hex head

screws from the center left side of the cabinet

and insert them into the holes just vacated by

the Phillips head screws on the center right side.

Invert the hinge bracket with shim and secure

this assembly with the three Phillips head screws

removed from the right side. Tighten all screws.

Center Right

Center Left

Transfer Top Hinge to the Left

Interchange the hinge, shims and screws at the top

right with the plastic plug buttons at the top left of

the cabinet. Place the hinge, shims and screws as

shown. Do not tighten screws at this time.

15

Adhesive spacer

Spacer

Hinge

Reversing the Refrigerator Handle

Remove screws from the top and bottom of the

handle to release the handle from door.

Remove the plastic screws from the right edge

of the door with a Phillips screwdriver and move

them to the handle screw holes on the left edge

of door.

Turn the handle upside-down and attach the

handle to the right edge of the door with the

screws at the top and bottom.

Transfer any hinge socket plug buttons to

the opposite end on the top and bottom of

both doors.

16

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Reversing the hardware.

Read these instructions completely and carefully.

On each door, move the metal door stop

from the right end to the left end.

Move any screws from the left end to the

right end.

Door Stop

Remove the handle by removing the two torx head

screws. Then, remove the two small plug buttons

and reinsert them into the two openings on the

opposite end of the door. Next, remove the large

plug button from the top edge of the door and

insert it into the opposite hole on the top edge of

the door. Reinstall the handle.

Large Plug

Button

Small Plug Buttons

Reversing the Freezer Handle

Transferring the Door Stops

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

17

Reversing the door swing.

Rehang the Freezer Door

On models with a hinge rod, remove the hinge

rod from the right side with a screwdriver and

install it in the left hinge side.

Lower the bottom socket of the freezer door

onto the lower hinge pin on the bottom hinge

bracket.

Gently push the door under the center hinge

bracket and align it with the hole in the center

hinge bracket.

On models with a hinge rod, make sure the

hinge rod has been inserted into the left hinge

socket before assembling the center hinge pin.

Reinstall the hinge pin with a 5/16″hex socket

driver so it extends through the hole in the

center hinge bracket and into the socket on top

of the freezer door.

Hinge Rod

(on some models)

Hinge Rod

(on some models)

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

18

Reversing the door swing.

Lower the bottom socket of the refrigerator

door onto the center hinge pin.

Tilt the door towards the cabinet, lifting the top

hinge so the pin fits into the socket on the top

of the door.

Tighten the top hinge screws to secure the door,

making sure the top edge of the door is even

with the top surface of the cabinet.

Center Hinge Pin

Remove the screws and switch with plastic plugs

in the opposite wall.

Reinstall ice tray shelf.

CAUTION: Do not loosen the center hinge bracket. To do

so could cause both doors to fall away from the cabinet.

Refrigerator Door:

Loosen the top hinge screws.

Adjust the door so it is flush with the cabinet.

Tighten screws.

Read these instructions completely and carefully.

Rehanging the Refrigerator Door

Transferring the Ice Shelf

Aligning the Doors

19

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Normal operating sounds.

www.GEAppliances.com

Depending on the placement of the refrigerator in your kitchen,

you may want to place a piece of rubber backed carpet under

the refrigerator to reduce noise.

Evaporator Fan.

You may hear air being forced through the cabinet

by the fan.

Evaporator.

The flow of refrigerant through the evaporator may create

a boiling or gurgling sound.

Defrost Heater.

During defrost cycles, water dripping onto the heater

may cause a hissing or sizzling sound. After defrosting, a popping sound

may occur and the evaporator may create a boiling or gurgling sound.

Cold Control.

This part can produce a snapping sound when turning

the refrigerator on or off.

Water Pan.

Water may be heard running into the drain pan during

the defrost cycle.

Compressor.

Modern, high efficiency compressors operate much faster

than older models. The compressor may have a high pitched hum or

pulsating sound.

Condenser Fan.

You may hear air being forced over the condenser

by the fan.

Defrost Timer.

The timer produces a sound similar to an electric clock.

Before you call for service…

Troubleshooting Tips

Save time and money! Review the charts on the following

pages first and you may not need to call for service.

Problem Possible Causes What To Do

Refrigerator does not

Refrigerator in defrost cycle. • Wait about 30 minutes for defrost cycle to end. If lights

operate

work but the unit does not restart, remove the base grille.

Locate the defrost timer mounted on the center rail and

turn the timer knob clockwise until you hear a click. The

refrigerator should begin operating.

Control in

OFF

position. • Move the control to a temperature setting.

Refrigerator is unplugged. • Push the plug completely into the outlet.

The fuse is blown/circuit • Replace fuse or reset the breaker.

breaker is tripped.

Vibration or rattling

Rollers need adjusting. • See

Rollers.

(slight vibration

is normal)

Consumer Support Troubleshooting Tips

Operating Instructions

Safety InstructionsInstallation Instructions

Before you call for service…

Problem Possible Causes What To Do

Motor operates for

Normal when refrigerator • Wait 24 hours for the refrigerator to completely

long periods or cycles

is first plugged in. cool down.

on and off frequently.

Often occurs when large • This is normal.

(Modern refrigerators

amounts of food are

with more storage

placed in refrigerator.

space and a larger

Door left open. • Check to see if package is holding door open.

freezer require more

Hot weather or frequent • This is normal.

operating time. They

door openings.

start and stop often

Temperature control • See

About the controls.

to maintain even

set at the coldest setting.

Grille and condenser need •See

Care and cleaning.

cleaning.

Refrigerator or freezer

Temperature controls not set • See

About the controls.

compartment too warm

cold enough.

Warm weather or frequent • Set the temperature control one step colder.

door openings. See

About the controls.

Door left open. • Check to see if package is holding door open.

Frost or ice crystals

Door left open. • Check to see if package is holding door open.

on frozen food

Too frequent or too long

(frost within package

door openings.

is normal)

Ice cubes have

Food transmitting odor/taste • Wrap foods well.

odor/taste

to ice cubes.

Interior of refrigerator •See

Care and cleaning.

needs cleaning.

Slow ice cube freezing

Door left open. • Check to see if package is holding door open.

Freezer control not set • See

About the controls.

cold enough.

Refrigerator has odor

Foods transmitting • Foods with strong odors should be tightly wrapped.

odor to refrigerator.

• Keep an open box of baking soda in the refrigerator;

replace every three months.

Interior needs cleaning. • See

Care and cleaning.

Moisture forms on

Not unusual during • Wipe surface dry and reset the refrigerator control

outside of refrigerator

periods of high humidity. one setting colder.

Moisture collects inside

Too frequent or too

(in humid weather, air

long door openings.

carries moisture into

refrigerator when doors

are opened)

temperatures.)

20

La page est en cours de chargement...

GE GBS22LBMCC Le manuel du propriétaire

Ce manuel convient également à

GE GBS22LBMCC Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents