Dometic RMDT 8501, RMDT 8505, RMDT 8551, RMDT 8555 Guide d'installation

REFRIGERATION

8 SERIES

RMDT8501, RMDT8505, RMDT8551,

RMDT8555

Absorber refrigerator with oven

Installation Manual

Réfrigérateur à absorption avec

four

Instructions de montage

EN

FR

title_RMDT8xxx_EN_FR.fm Seite 1 Dienstag, 21. Februar 2017 6:55 18

RMDT 8501 RMDT 8505

RMDT 8551 RMDT 8555

MBA 06/2014

N 0-1

Installation Instructions

Absorption Refrigerator + Oven

for Recreation Vehicles

EN

English

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 1

2

Dometic GmbH

In der Steinwiese 16

D-57074 Siegen

www.dometic.com

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 2

1.0 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Guide to these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

1.3 Copyright protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Explanation of symbols used in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.5 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.6 Limitation of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.7 Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.0 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Application according to regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.2 User's responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.3 Working upon and checking the refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.4 Operating the refrigerator with gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3.0 Description of model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Model identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 Refrigerator rating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.3 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.0 Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.1.1 Side installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.1.2 Rear installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4.1.3 Draught-proof installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4.2 Installation recess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2.1 Recess dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.3 Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3.1 Ventilation and air extraction of the refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3.2 Oven ventilation and exhaust duct to vehicle's interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3.2.1 Ventilation to vehicle's interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.3.2.2 Ventilation via roof flue cowl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.3.3 Height of ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.4 Installing the ventilation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.4.1 Installation LS300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.4.2 Truma roof cowl AK3 installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.4.3 Installation of ventilation grill for ovens with interior ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.5 Exhaust duct system (refrigerator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.6 Securing the refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.7 Insert the decor panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.8 Gas installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.8.1 Connection pressure and gas categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.9 Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.9.1 Mains connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.9.2 12V (battery) connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.9.3 Cable connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4 .9.4 D+ and solar connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.9.5 Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3

Table of Contents

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 3

4

General

1.0 General

On installation of the appliance, the technical

and administrative regulations of the country

in which the vehicle will first be used must be

adhered to. Otherwise the refrigerator must be

installed as described in these instructions. In

Europe, for example, gas appliances, cable

routing, installation of gas cylinders, as well as

approval and checking for leaks must comply

with EN 1949 for liquid gas systems in vehi-

cles.

1.1 Introduction

The information, texts and illustrations in these

instructions are copyright protected and are

subject to industrial property rights.

No part of these instructions may be reprodu-

ced, copied or utilised in any other way wit-

hout written authorisation by Dometic GmbH,

Siegen, Germany.

1.3 Copyright protection

Before you start installing the refrigerator,

please read the installation instructions

carefully.

These instructions provide you with the neces-

sary guidance for the proper installation of

your refrigerator. Observe in particular the

safety instructions. Observation of the

instructions and handling recommendations is

important for dealing with the refrigerator

safely and for protecting you from injury and

the refrigerator from damage. You must under-

stand what you have read before you carry out

a task.

Keep these instructions in a safe place

close to the refrigerator so they may be

referred to at any time.

1.2 Guide to these installation

instructions

1.4 Explanation of symbols

used in this manual

Warning notices are identified by symbols. A

supplementary text gives you an explanation

of the degree of danger.

Observe these warning notices rigorously.

You will thus protect yourself and other

people from injury, and the appliance from

damage.

Warning notices

DANGER indicates an imminent hazardous

situation which, if not avoided, could result in

death or serious injury.

DANGER!

WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury

WARNING!

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

CAUTION!

CAUTION (used without the safety alert sym-

bol) indicates a potentially hazardous situation

which, if not avoided, may result in damage to

the appliance.

CAUTION!

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 4

5

General

All information and guidance in these opera-

ting instructions were prepared after taking

into consideration the applicable standards

and regulations as well as the current state of

the art. Dometic reserves the right to make

changes at any time which are deemed to be

in the interest of improving the product and

safety.

Dometic will assume no liability for damage in

the case of :

 non-observation of the operating instructi-

ons

 application not in accordance with the

regulations or provisions

 use of non-original spare parts

 modifications and interferences to the

appliance

 effect of environmental influences, such as

- temperature fluctuations

- humidity

1.6 Limitation of liability

1.7 Declaration of conformity

Information

INFORMATION gives you supplementary and

useful guidance when dealing with your refrige-

rator.

Environmental Tips

ENVIRONMENTAL TIPS gives you useful gui-

dance for saving energy and disposal of the

appliance.

Warranty arrangements are in accordance

with EC Directive 44/1999/CE and the normal

conditions applicable for the country concer-

ned. For warranty or other maintenance, plea-

se contact our customer services department.

Any damage due to improper use is not cover-

ed by the warranty. The warranty does not

cover any modifications to the appliance or

the use of non-original Dometic parts. The

warranty does not apply if the installation and

operating instructions are not adhered to and

no liability shall be entertained.

1.5 Warranty

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 5

6

This refrigerator / oven is designed for installa-

tion in recreation vehicles such as caravans or

motorhomes. The appliance has been type-

approval tested for this application in accor-

dance with the EC Gas Directive.

The refrigerator is to be used solely for storing

foodstuffs and the oven for cooking dishes.

Any other use is considered improper and

incorrect creating hazardous conditions.

2.3 Working upon and checking

the refrigerator / oven

Work on gas equipment, exhaust system

and electrical facilities must be carried

out by authorised personnel only.

Substantial damage to property and/or

injury to persons can arise through unpro-

fessional procedures.

WARNING!

Anyone operating the refrigerator must be

familiar with the safe handling and understand

the advice in these operating instructions.

2.2 User's responsibility

 Flammable materials must be kept at a

safe distance to the oven.

 The refrigerator must not be exposed to

rain.

CAUTION!

Safety instructions

2.0 Safety instructions

2.1 Application according to

regulations

Never use an unshielded flame to check

gas bearing parts and pipes for leakage!

There is a danger of fire or explosion..

DANGER!

Never open the absorber cooling unit! It is

under high pressure.

There is a danger of injury!

WARNING!

It is imperative that the operating pressure

corresponds to the data specified on the

rating plate of the appliance. Compare the

operating pressure of the rating plate with the

data specified on the pressure reducing valve

of the liquid gas cylinder.

2.4 Operating the appliance

with gas

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 6

7

Fig. 1

RM

8 5 0 1

1

5

D

T

Refrigerator Mobile /

Mobile Absorption Refrigerator

Model range

with oven

5 = width 523mm

Depth:

0 = Standard

5 = + 55mm

6 = + 65mm

Double door refrigerator

Example :

1

manual energy selection, automatic ignition

(MES)

5

automatic and manual energy selection,

automatic ignition (AES)

Example

Model number

Product number

Serial number

Electrical rating details

Gas pressure

2

1

3

4

5

Description of model

3.0 Description of model

3.1 Model identification

The rating plate is to be found on the inside of

the refrigerator. It contains all important details

of the refrigerator. You can read off from this

the model identification, the product number

and the serial number. You will need these

details whenever you contact the customer

service centre or when ordering spare parts.

3.2 Refrigerator rating plate

2 3

4

5

RMDT 8501

1

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 7

8

Description of model

3.3 Technical data

Dometic refrigerators are equipped for a con-

nection pressure of 30 mbar. For connection

to a 50 mbar gas system, use Truma VDR

50/30 medium pressure controller

Model Dimensions Gross capacity

Rating details

Consumption * Net Ignition

H x W x D (mm) with freezer mains/battery electricity/gas weight Piezo Automat

Depth incl. door compartment freezer cmpt. over 24hrs

Subject to technical changes.

*

Average consumption measured at an average ambient

temperature of 25°C in pursuance of ISO Standard.

RMDT 8501

RMDT 8505

RMDT 8551

RMDT 8555

*RMDT 85xx

with grill

oven only

1515*x523x567

1515*x523x622

1545x523x622

270x523x470

160 lit.

190 lit.

25 lit.

53.4 kg

54.9 kg

16.4 kg

30 lit.

35 lit.

250 W / 170 W

25

0 W / 170 W

250 W / 170 W

•

ca.

4,2 KWh / 420 g

ca.4,2 KWh / 420 g

Gas / h 70-100 g

Fig. 2

RMDT 85xx / oven without grill

RMDT 85xx / oven with grill

H

B

T

H

B

T

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 8

9

Installation

Fig. 3

Fig. 4

Air vent grille not

blocked! OK!

4.0 Installation instructions

The unit and the exhaust duct system must be

in principle installed so that it is accessible for

maintenance work, can be easily installed and

dismantled and removed from the vehicle wit-

hout great effort.

Installation and connection of the appliance

must comply with the latest technical regulati-

ons, as follows:

 The electrical installation must comply

with national and local regulations.

 The gas installation must comply with

national and local regulations.

 European Standards EN 1949

 European Standards EN 60335-1,

EN 60335-2-24, EN 1648-1 , EN 1648-2

 The appliance must be installed in such

a way that it is shielded from excessive

heat radiation.

Excessive heat impairs performance and rai-

ses the energy consumption of the refrigera-

tor!

4.1 Installation

Deviations from these installation instructi-

ons without prior notification of Dometic

result in Dometic GmbH's warranty obliga-

tions becoming void!

The appliance may be installed by autho-

rised personnel only!

WARNING!

(Fig. 4 )The air vent grilles offer an unobstruc-

ted dissipation of heat and exhaust gas even

when the door is opened.

4.1.1 Side installation

If the appliance is installed on the same side of

the vehicle as the entrance door, it is desirable

that the door does not cover the refrigerator's

vents. (Fig. 3, Clearance door/ventilation grille

at least 25 mm). Otherwise ventilation could

be impaired which causes a loss in cooling

performance. Awnings are often placed at the

door side of a caravan. This complicates eva-

cuation of combustion gases and heat through

the ventilation grilles (loss in cooling perfor-

mance)!

(Fig. 3) The air vent grilles are blocked. There

must be a distance between the door and the

air vents of at least 25 mm!

If the door/grille distance is between 25 mm

and 45 mm, we recommend installing a

Dometic ventilation kit

(item no. 241 2985 -

00/0)

to achieve an optimal cooling perfor-

mance in high ambient temperatures.

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 9

10

Installation

Another unfavourable method of rear installa-

tion is to install the air intake and exhaust gril-

les (Fig. 6) at the side wall of the recreation

vehicle. The air-heat recirculation is very

restricted which means that heat exchangers

(condenser, absorber) cannot be adequately

cooled. The optional method of an additional

air vent grille installed in the floor also exhibits

an insufficient air flow duct.

Fig. 5

Air vent grille

not blocked!

OK!

4.1.2 Rear installation

Rear installation often causes an unfavourable

installation arrangement, as ideal ventilation

cannot always be assured (e.g. the lower ven-

tilation grille is covered by the bumper or the

rear lights of the vehicle!). The maximum coo-

ling performance of the aggregate is actually

not available.

The maximum cooling performance is not

available! Do not apply this installation

method, as it does not provide proper ven-

tilation! Please refer to the description in

section 4.2.

CAUTION!

Fig. 6

4.1.3 Draught-proof installation

Refrigerators in motorhomes, caravans or

other vehicles must be installed in a draught-

proof manner (EN 1949). This means that the

combustion air for the burner is not taken from

the living space and that exhaust fumes are

prevented from entering the living space.

Adequate sealing between the back of the

refrigerator and the vehicle interior has to be

provided.

Dometic strongly recommend using a flexible

sealing for this purpose (temperature-resi-

stant up to 200 °C in the area of the oven),

in order to facilitate future removal or installati-

on of the appliance during maintenance

By no means use durable sealing com-

pounds, fitting foam or similar material to

realise draught-proof installation of the

refrigerator ! Do NOT use any easily

inflammable materials for sealing (in parti-

cular silicon sealing compound or similar).

Risk of fire! The device manufacturer's

product liability and warranty shall lapse if

such materials are used.

WARNING!

The lip seals (1) are installed at the bottom and

on each side in the installation recess (Fig. 7-

9). A heat deflector plate (2) is installed in the

installation recess above the refrigerator. Affix

this plate to the caravan wall, do NOT

attach to the refrigerator !

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 10

11

Installation

Deviations shall require the consent of the

manufacturer.

Fig. 8

Fig. 7

Fig. 9

Fig. 10

Attach the deflector plate so that the heated

air escapes through the top ventilation grill into

the open air and no heat build-up can be pro-

duced.

The refrigerator is later pushed into the instal-

lation recess from the front. Ensure that the

seals abut the case evenly.

This installation option facilitates the removal

and installation of the appliance for servicing.

If the cavity between the caravan wall and the

refrigerator is sealed so that fumes cannot

penetrate the living area it is possible to vent

the flue gas directly through the upper grille

without using the aluminium flue pipe. The

waste gases escape to the outside through

the upper grill of the ventilation. Do not use

any kind of aluminium flue pipe to lead the flue

gas out.

Fasten the sealing lips to a stop bar on the

rear side (1), e.g. by gluing.

1

2

1

2

Proposal 1

Proposal 2

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 11

12

Installation

Fig. 11

Appliance without grillfunction

ventilation grille

LS300

condenser

cooling unit

gap between coo-

ling unit and wall:

min. 15 mm

ventilation grille

LS300

Truma-flue outlet

AK3

removable screen /

grill

(for fixing of flue outlet)

heat reflector

170 mm min

The refrigerator must be installed draught-

proof in a recess (also refer to Section "4.1.3").

The measurements of the recess are stated in

the table below. Push the appliance far

enough into the recess until the front edge of

the refrigerator casing is aligned with the front

of the recess. Allow a gap of 20 mm bet-

ween the back wall of the recess and the refri-

geration unit. The floor of the recess must be

level, allowing the appliance to be pushed

easily into its correct position. The floor must

be substantial enough to bear the weight of

the appliance. Install a removable screen / grill

above the oven (for fixing and removing of flue

outlet).

Ensure that the refrigerator is installed level

in the recess.

4.2 Installation recess

Fig. 12

Appliance with grillfunction

ventilation grille

LS300

condenser

cooling unit

gap between

cooling unit and

wall: min. 15 mm

ventilation grille

LS300

Truma-flue outlet

AK3

removable screen /

grill

(for fixing of flue outlet)

heat reflector

170 mm min

Observe instructions “4.3

Ventilation

” !

Correct mounting of the lower ventilation grille

facilitates access to the connections and

functional parts during maintenance.

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 12

13

Installation

4.2.1 Recess dimensions

RMDT 8501, RMDT 8505

Model

Height Width Depth

1685 mm 527 mm 510 mm

RMDT 8551, RMDT 8555

Model

Height Width Depth

1685 mm 527 mm 565 mm

 Distance of refrigerator unit to wall:

20 mm

 Top edge of oven to ceiling: 170 mm

Ventilation grille

Minimum wall clearances

Appliance without grill function

Fig. 13

Appliance with grill function

Fig. 14

Fig. 15

H

T

1

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 13

14

Installation

Fig. 17

In the event of high ambient temperatures,

full performance of the cooling unit can

only be achieved by means of adequate

ventilation and extraction.

A correct installation of the refrigerator is

essential for its correct operation, as due to

physical reasons heat builds up at the back of

the appliance which must be allowed to esca-

pe into the open air.

If ventilation and exhaust duct into the vehicle

is intended, fresh air supply must not be

obstructed. The room in which the device is

installed must have one or several openings

allowing fresh air to enter (safety ventilation

according to EN 721). These openings must

have a total cross section of at least 100

cm². There must be one or several ventila-

tion openings above the device with mini-

mum cross sections of 150 cm². These have

to be checked and if necessary cleaned regu-

larly. Roof and wall outlet openings can be

combined. Lower ventilation openings must

be no more than 100 mm above the inside

floor. The ventilation openings must by no

means be shut. Grilles and covers must be

kept clean and free of dust.

4.3.1 Ventilation and air extraction of

the refrigerator

4.3 Ventilation

4.3.2 Oven ventilation and exhaust

duct to vehicle's interior

4.3.2.1 Ventilation to vehicle's interior

(special equipment, model without

flue)

exhausts

Large panel with ventilation slots

(for ventilation to the vehicle’s interior)

Ventilation is provided for the unit by means of

two apertures (ventilation grilles) in the cara-

van wall. Fresh air enters at the bottom,

extracts the heat and exits through the upper

vent grille (chimney effect). The upper venti-

lation grille should be positioned as high as

possible above the cooling unit (Fig. 11).

Install the lower ventilation grille at floor

level of the recess floor (Fig. 16), allowing

unburnt gas (heavier than air) to escape direct-

ly into the open air. The gas burner must be

located above the edge (1) ..

Should this arrangement prove impossible,

a ventilation aperture must be introduced

by the manufacturer of the vehicle into the

recess floor in order to avoid the accumula-

tion of unburnt gas on the floor.

The ventilation grilles must have an open

cross-section of at least 400 cm². This is

achieved by using the Dometic LS 300 absor-

ber ventilation and air extraction system

which has been tested and approved for this

purpose.

Fig. 16

1

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 14

15

Installation

Special cowls for mounting on the roof are

used for the ventilation and exhaust gas duct.

Only use the cowl and pipes specified in

these instructions. These are tested and

approved for the application.

CAUTION!

There must not be any materials not desi-

gned for temperatures over 120 °C in the

vicinity of cowl and exhaust gas pipe.

CAUTION!

The hot exhaust air escapes from inside the

oven through the ventilation slots in the front

panel.

4.3.2.2 Ventilation via roof flue cowl

4.3.3 Ventilation heights

Fig. 20

Minimum ventilation height

LS300

H

K

Minimum ventilation height H

B

Oven :

Truma roof flue cowl AK3 250 mm

Minimum ventilation height H

K

Refrigerator :

upper ventilation grille LS 300

lower ventilation grille LS 300 > 1400 mm

H

B

1

Details on oven ventilation to vehicle's

interior

Fig. 18

Fig. 19

Truma roof flue

cowl AK3

panel with ventilati-

on slots

gas burner

exhausts

incoming air

removable

screen

10 mm

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 15

16

Installation

4.4.2 Truma roof cowl AK3 installation

A round cutout with diameter 60 mm is made

in the vehicle roof for the installation of the

Truma roof cowl. The roof cowl is bolted in the

roof cutout. The flexible stainless steel flue

pipe is pushed into the roof cowl and onto the

spout of the exhaust gas outlet (1) and fixed

with a worm drive clamp or the bolts supplied

by Truma to the roof cowl.

The exhaust gas duct must slope upward.

The minimum installation height of the flue

pipe between top edge of the unit and exhaust

gas outlet at the cowl must not be less than

250 mm. A maximum of 1500 mm is possible.

A clearance of at least 50 mm from surroun-

ding walls and components must be maintai-

ned.

 Truma roof flue cowl AK3

30700-03

 Truma flue pipe

30330-00

Truma part numbers

Fig. 26

1

Fig. 21

Cut two rectangles in the

exterior wall of the vehi-

cle.

1

Fig. 22

Seal the mounting frame

making it waterproof

(

does not apply for

mounting frames with

integral seal)

and screw

into position.

2

Fig. 23

Insert ventilation grille.

Fig. 24

Install locking slider.

4

Fig. 25

Lock ventilation grille.

5

b

a

14 x

4.4 Installing the ventilation

system

4.4.1 Installing LS300

To install the ventilation grilles, cut two rectan-

gles width b = 490mm, height a= 249mm, in

the outer wall of the vehicle (for position of the

cuts, see Fig.11).

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 16

17

The exhaust gas duct system must be made in

such a manner as to achieve a complete

extraction of combustion products to the out-

side of living space. The flue gas is vented

directly through the upper grille. Do not use

any kind of aluminium flue pipe to lead the flue

gas out.

The T-piece (Fig. 28) must be aligned with the

exterior wall.

EAn installation other than described will

reduce the cooling capacity and jeopardi-

se the manufacturer's warranty/product

liability.

CAUTION!

Installation

4.5 Exhaust duct system

(refrigerator)

After the refrigerator is put in its final place,

secure the screws into the wall of the recess.

The screws must penetrate the casing of the

refrigerator.

Fig. 29

Fig. 27

In the sidewalls of the refrigerator, there are

four plastic sleeves for securing the refrigera-

tor. The sidewalls or strips attached for secu-

ring the refrigerator must be prepared to hold

the screws firmly in place even when under

increased load (while the vehicle is moving).

Fastening screws and caps are supplied with

the refrigerator.

4.6 Securing the refrigerator

Always insert screws through the sleeves

provided as otherwise components laid in

foam, such as cables etc., could be dama-

ged.

CAUTION!

Fig. 28

45°

4.4.3 Installation of ventilation grill for

ovens with interior ventilation

For these ventilation variants, install a ventila-

tion grill above the oven with the dimensions :

width = 522 mm

height = 90 mm .

Proposal :

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 17

18

Installation

Fig. 31

Fig. 32

Fig. 30

Fig. 33

1

2

CAUTION!

3

4

2

1

Fig. 34

1

Fig. 37

Fig. 35 Fig. 36

3

4

2

4.7 Insert the decor panel

Decor panel dimensions (frame) :

300 +/- 1 mm 507,5 +/- 1 mm max. 1.7 mm

Upper door

Height Width Thickness

907,4 +/- 1 mm 507,5 +/- 1 mm max. 1.7 mm

Lower door

Height Width Thickness

Frameless decor panel

Decor panel with frame



Remove the lateral ledge (1) from the door

(ledge is attached, not screwed).

Shift decor panel (2) away from the door

and insert the new decor panel. Re-attach

ledge (1).

289 0318-40_EN_RMDT85xx-Installation_N1.qxp 20.08.2012 12:32 Seite 18

La page charge ...

Dometic RMDT 8501, RMDT 8505, RMDT 8551, RMDT 8555 Guide d'installation

Ce manuel convient également à

Dometic RMDT 8501, RMDT 8505, RMDT 8551, RMDT 8555 Guide d'installation

dans d''autres langues

Documents connexes