THANK YOU for purchasing this high-quality product. Register your freezer at www.whirlpool.com. In Canada, register your freezer
at www.whirlpool.ca.
For future reference, please make a note of your product model and serial numbers. These numbers can be found inside your freezer.
Model Number____________________________________________
Serial Number_____________________________________________
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
User Guide
Upright Freezer
SAFETY
TABLE OF CONTENTS
W11320197A
SAFETY ....................................................................................... 1
Proper Disposal of Your Old Freezer or Refrigerator ................... 2
INSTALLING YOUR FREEZER .................................................. 3
Unpacking ................................................................................... 3
Location Requirements ............................................................... 3
Electrical Requirements ............................................................... 4
Ice Maker Kit ............................................................................... 4
Water Supply Requirements
(on some models) ........................................................................ 4
Connect the Water Supply
(on some models) ........................................................................ 5
Remove and Replace the Handle ................................................ 5
Freezer Door ................................................................................ 6
Freezer Leveling and Door Closing ............................................. 7
OPERATING YOUR FREEZER .................................................. 8
Ensuring Proper Air Circulation ................................................... 8
Using the Control ........................................................................ 8
Key Eject Lock (on some models) ............................................... 9
Ice Maker (on some models) ....................................................... 9
Freezer Features .......................................................................... 9
CARING FOR YOUR FREEZER ............................................... 10
Cleaning Your Frost-Free Freezer ............................................. 10
Changing the Light Bulb(s) (on some models) .......................... 11
Power Interruptions ................................................................... 11
Moving Care .............................................................................. 11
TROUBLESHOOTING .............................................................. 11
Freezer Operation ...................................................................... 12
Ice Production ........................................................................... 13
Ice Quality .................................................................................. 13
WARRANTY .............................................................................. 14
2
Proper Disposal of Your Old
Freezer or Refrigerator
IMPORTANT: Child entrapment and suffocation are not
problems of the past. Junked or abandoned freezers or
refrigerators are still dangerous — even if they will sit for
“just a few days.” If you are getting rid of your old refrigerator or
freezer, please follow these instructions to help prevent
accidents.
Before You Throw Away Your Old
Freezer or Refrigerator:
■Take off the doors or lid.
■Leave the shelves in place so that
children may not easily climb inside.
WARNING:
IMPORTANT SAFETY INSTRUCTIONS
PLEASE KEEP THESE INSTRUCTIONS
Plug into a grounded 3-prong outlet.
Do not remove the ground prong.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before servicing.
Replace all parts and panels before operating.
Remove doors from your old appliance.
Use non-flammable cleaner.
Keep flammable materials and vapors, such as gasoline, well
away from the appliance.
Use two or more people to move and install the appliance.
Disconnect the power before installing the ice maker (on ice
maker kit-ready models only).
Ice maker kit ECKMF95 can be added to some models.
A qualified service technician must install the water line and
ice maker. See installation instructions supplied with ice
maker kit ECKMF95 for complete details.
■ Connect to a potable water supply only.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
person in order to avoid a hazard.
Do not store explosive substances such as aerosol can
with a flammable propellant in this appliance.
This appliance is intended to be used in household and
similar applications such as
- Staff kitchen areas in shops, offices and other working
environments;
- Farm houses and by clients in hotels, motels and other
residential type environments;
- Bed and breakfast type environments;
- Catering and similar non-retail applications.
To reduce the risk of fire, electric shock or injury to persons when using the appliance,
follow basic precautions, including the following:
WARNING
Suffocation Hazard
Remove doors or lid from your old freezer or
refrigerator.
Failure to do so can result in death or brain damage.
Important information to know about disposal of
refrigerants:
Dispose of freezer in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.
3
Unpacking
Remove Packaging Materials
■Remove tape and glue residue from surfaces before turning
on the freezer. Rub a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and
dry.
■Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your freezer. For more
information, see “Safety.”
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your freezer before using it. See the cleaning instructions in
the “Caring for Your Freezer” section.
Location Requirements
Ventilation and Clearance
■Keep flammable materials and vapors, such as gasoline,
away from freezer.
■Do not cover the freezer with items such as blankets, sheets,
tablecloths, etc. This reduces air circulation.
■Allow at least 3" (7.5 cm) of air space at the top and on both
sides of the freezer and 1" (2.5 cm) between the back of the
freezer and the wall. If the freezer is to be next to a fixed wall,
leave extra space on the hinge side so the door can open
wider.
Temperature
Your freezer operates most efficiently when located in an area
where the temperature will not fall below 40°F (5°C). Place your
freezer in a location where the temperature will not fall below this
recommended temperature.
Upon Moving to Final Location
NOTE: Allow for a 3" (7.5 cm) clearance at the top and sides and
1" (2.5 cm) between the back and wall.
WARNING
Excessive Weight Hazard
Use two or more people to move and install freezer.
Failure to do so can result in back or other injury.
When Moving Your Freezer:
Your freezer is heavy. When moving the freezer for cleaning
or service, be sure to cover the oor with cardboard or
hardboard to avoid oor damage. Always pull the freezer
straight out when moving it. Do not wiggle or “walk” the
freezer when trying to move it, as oor damage could occur.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from freezer.
Failure to do so can result in death, explosion, or fire.
3" (7.5 cm)
3" (7.5 cm)
INSTALLING YOUR FREEZER
4
Electrical Requirements
Before you move your freezer into its final location, it is important
to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 V, 60 Hz, AC-only, 15 or 20 A fused, grounded electrical
supply is required. It is recommended that a separate circuit
serving only your freezer be provided. Use an outlet that cannot
be turned off by a switch. Do not use an extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, press and hold TEMP SETTING for
3 seconds to turn off cooling, and then disconnect the freezer
from the electrical source.
Ice Maker Kit
Ice Maker kit ECKMF95 can be added to some models.
NOTE:
■Please follow the installation instructions supplied in the
ice maker kit.
■Connect to potable water only.
Water Supply Requirements
(on some models)
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
■Flat-blade screwdriver
■7/16" and 1/2" open-end
or 2 adjustable wrenches
■1/4" nut driver
■1/4" drill bit
■Cordless drill
NOTE: Your freezer dealer has a kit available with a
1/4" (6.35 mm) saddle-type shut-off valve, a union, and plastic
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a
piercing-type or 3/16" (4.76 mm) saddle valve which reduces
water flow and clogs more easily.
IMPORTANT:
■Connect to potable water supply only.
■If you turn the freezer on before the water line is connected,
turn the ice maker off.
■All installations must meet local plumbing code
requirements.
■Use plastic tubing and check for leaks. Install plastic tubing
only in areas where temperatures will remain above freezing.
Water Pressure
A cold water supply with water pressure of between
30 and 120 psi (207 to 827 kPa) is required to operate the water
dispenser and ice maker. If you have questions about your water
pressure, see “Troubleshooting” or call a licensed, qualified
plumber.
Reverse Osmosis Water Supply
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the system needs to be
a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa), a booster pump can be inserted
into the small tubing that goes from the cold water line to the
reverse osmosis system.
If the water dispenser is still not dispensing water properly:
■Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
■Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
■If your freezer has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter.
If you have questions about your water pressure, refer to
“Troubleshooting” or call a licensed, qualified plumber.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
5
Connect the Water Supply
(on some models)
Connect to Water Line
1. Unplug freezer or disconnect power.
2. Turn off main water supply. Turn on nearest faucet long
enough to clear line of water.
3. Locate a 1/2" to 1¼" (12.7 mm to 3.18 cm) vertical cold
water pipe near the freezer.
IMPORTANT:
■Make sure it is a cold water pipe.
■Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Determine the length of plastic tubing you need. Measure
from the connection on the lower-left rear of freezer to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
1/4" (6.35 mm) O.D. (outside diameter) plastic tubing.
Be sure both ends of plastic tubing are cut square.
5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold
water pipe you have selected.
6. Fasten the shut-off valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten or you may crush the plastic tubing.
7. Slip the compression sleeve and compression nut on the
plastic tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression
nut onto outlet end with adjustable wrench.
Do not overtighten.
8. Place the free end of the tubing in a container or sink and
turn on the main water supply. Flush the tubing until water is
clear. Turn off the shut-off valve on the water pipe. Coil the
plastic tubing.
Connect to Freezer
1. Attach the plastic tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do
not overtighten.
2. Use the tube clamp on the back of the freezer to fasten the
tubing to the freezer as shown. This will help avoid damage
to the tubing when the freezer is pushed back against the
wall.
3. Turn shut-off valve on.
4. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
5. The ice maker is equipped with a built-in water strainer. If
your water conditions require a second water strainer, install
it in the 1/4" (6.35 mm) water line at either tube connection.
Obtain a water strainer from your nearest appliance dealer.
6. Plug into a grounded 3 prong outlet.
Remove and Replace the Handle
To Remove the Handle:
1. Loosen the setscrews located on the side of handle at
each end. See “Door Swing Reversal and Handle Removal”
graphic.
2. Remove the handle from the grommets.
To Replace the Handle:
1. Place the handle onto the grommets making sure the
grommets are fitted into the handle holes.
2. Tighten the upper and lower setscrews with the hex key
provided. See “Door Swing Reversal and Handle Removal”
graphic. Do not overtighten the setscrews.
A
B
C
DFE
G
A. Cold water pipe
B. Pipe clamp
C. Plastic tubing
D. Compression nut
E. Compression sleeve
F. Shut-off valve
G. Packing nut
A
C
B
D
E
A. Tube clamp
B. Tube clamp screw
C. Plastic tubing
D. Compression nut
E. Valve inlet
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
6
Freezer Door
Tools Needed: 5/16" hex-head socket wrench, 3/8" hex-head
socket wrench, flat 2" putty knife.
IMPORTANT:
■All graphics referenced in the following instructions are
included later in this section after “Final Steps.” The graphics
shown are for a right-hand swing door (hinges factory
installed on the right).
■If you only want to remove and replace the door, see the
“Remove Door and Hinges” and “Replace Door and Hinges.”
■Before you begin, turn the control OFF and remove food and
adjustable door or utility bins from door.
Remove Door and Hinges
1. Unplug freezer or disconnect power.
2. Keep the freezer door closed until you are ready to lift it free
from the cabinet.
NOTE: Provide additional support for the door while he hing-
es are being moved. Do not depend on the door magnets to
hold the door in place while you are working.
3. Remove the parts for the top hinge as shown in Top Hinge
graphic in the “Door Swing Reversal and Handle Removal”
section.
4. Lift the freezer door free from the lower hinge and cabinet
and set aside.
5. Remove the 4 hex-head hinge screws and bottom hinge
assembly. See Bottom Hinge graphic in the “Door Swing
Reversal and Handle Removal” section.
Reverse Door (optional on some models)
IMPORTANT: If you want to reverse your door so that it opens in
the opposite direction, continue with “Reverse Door (optional on
some models)” instructions. If you are not reversing the door, see
“Replace Door and Hinges.”
Cabinet
1. Remove the cabinet hinge hole plugs from the cabinet top
and move them to the opposite side hinge holes as shown
in Graphic 2 in “Door Swing Reversal and Handle Removal”
section.
2. Remove the bottom hinge pin from the hinge bracket.
3. Remove the decals covering the holes on the opposite side
of the bottom hinge.
4. Reinstall the bottom hinge pin in the alternate hole in the
hinge bracket. See Graphic 3 in “Door Swing Reversal and
Handle Removal” section.
5. Reinstall the hinge bracket to the cabinet with the 4 hex-
head hinge screws.
Door
1. Remove the hinge thimble hole plug from the top of the door.
2. Remove the door stop from the bottom of the door.
3. Move the door stop to the opposite side, making sure that
the hole in the door stop plate is aligned perfectly with the
hole in the door for the bottom hinge pin.
4. Using the screws removed in Step 2, fasten the door stop
bracket to the bottom of the door.
5. Tighten all screws. Set aside the door until the bottom hinge
is in place.
Replace Door and Hinges
NOTE: Graphic may be reversed if door swing is reversed.
1. Replace the parts for the bottom hinge as shown and tighten
screws. See Bottom Hinge graphic. Replace the freezer door.
NOTE: Provide additional support for the door while the
hinges are being moved. Do not depend on the door mag-
nets to hold the door in place while you are working.
2. Assemble the parts of the top hinge as shown in the Top
Hinge graphic in the “Door Swing Reversal and Handle
Removal” section. Do not tighten the screws completely.
Final Steps
1. Check all holes to make sure that hole plugs and screws are
in place. Reinstall top hinge cover. See Top Hinge graphic.
2. Using the provided decals, cover the remaining holes located
on the opposite side from the bottom hinge.
3. Plug into a grounded 3 prong outlet.
4. Reset the control. See “Using the Control.”
5. Return all removable door parts to door and food to freezer.
WARNING
Excessive Weight Hazard
Use two or more people to lift the freezer door.
Failure to do so can result in back or other injury.
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or
electrical shock.
Hex-head hinge screws
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
7
1.
A
2
A
B
C
1
3
A
B
B
C
A
B
A
B
Door Swing Reversal and Handle Removal (optional)Door Removal &
Replacement
Top Hinge
A. Top Hinge Cover
B. 5/16" Hex-Head Hinge Screws
C. Top Hinge
A. Hinge Pin
B. 3/8" Hex-Head Hinge Screws
A. Hinge Pin
B. 3/8" Hex-Head Hinge Screws
A. Grommet
B. Handle
C. Setscrews
A. Cabinet Hinge Hole Plugs
Freezer Leveling and Door Closing
Style 1—without Grille
1. Locate the 2 front leveling legs taped among the packing
materials.
2. Screw these legs into the front holes on
the bottom of the freezer. The back of the
freezer rests on 2 fixed supports.
3. Adjust the front legs enough to lift the
cabinet up off the floor.
4. Place a leveling tool on top of the freezer first side to side,
then front to back. Turn leg counterclockwise to raise a
corner. Turn leg clockwise to lower a corner.
5. Repeat Step 4 until freezer is level.
6. After freezer is fully loaded with food, recheck with level as in
Step 4.
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
8
Style 2—with Grille
Your freezer has 2 front adjustable legs — one on each side. The
back of the freezer rests on 2 fixed rollers. The base grille covers
the adjustable brake feet and roller assemblies located at the
bottom of the freezer below the freezer door. Before making any
adjustments, remove the base grille and move the freezer to its
final location.
Tools Needed: 1/4" hex driver, Phillips head screwdriver
1. Remove the base grille screws. Grasp the grille rmly and
pull it toward you. Open the freezer door to access the brake
feet.
NOTE: To allow the freezer to roll more easily, raise the brake
feet by turning them counterclockwise. The front rollers will
be touching the floor.
2. Move the freezer to its nal location.
3. Lower the brake feet, by turning them clockwise, until the
rollers are off the oor and both brake feet are snug against
the oor. This keeps the freezer from rolling forward when
you are opening the freezer door.
IMPORTANT: If you need to make further adjustments
involving the brake feet, you must turn both brake feet the
same amount to keep the freezer level.
4. Make sure the door closes easily. If you are satised with the
door opening and closing, skip the next section. If, however,
the door does not close easily or the door pops open, adjust
the tilt.
To Adjust the Cabinet Tilt:
NOTE: Having someone push against the top of the freezer
takes some weight off the brake feet. This makes it easier to turn
them. Open the freezer door. Use a 1/4" hex driver to turn both
brake feet clockwise the same amount. This will raise the front of
the freezer. It may take several turns to allow the door to close
more easily.
5. Make sure the freezer is steady. If the freezer seems
unsteady or rolls forward when the door is pulled open,
adjust the brake feet.
To Steady the Freezer:
■Open the freezer door. Using a 1/4" hex driver, turn both
brake feet clockwise the same amount until the brake feet
are snug against the oor. Check again. If not satised,
continue to adjust the brake feet by half turns of the screw
until the freezer does not roll forward when the door is
opened.
6. Replace the base grille by aligning the ends of the grille with
the leveling assemblies on each side and snapping the grille
into place. Reinstall the Phillips screws.
Ensuring Proper Air Circulation
In order to ensure proper temperature,
you need to permit proper airflow in
the freezer. As shown in the illustration,
cool air enters from the freezer wall and
moves down. The air then recirculates
through the vent near the bottom.
Do not block any of these vents with
food packages. If the vents are blocked,
airflow will be restricted and temperature
and moisture problems may occur.
IMPORTANT: To avoid odor transfer and
drying out of food, wrap or cover foods
tightly.
Using the Control
The temperature control is located at the top front of the freezer
compartment.
Temperature Control
For your convenience, the temperature control is preset at the
factory. When you first install your freezer, check that the control
is still set to the recommended setting as shown.
IMPORTANT:
■The recommended setting is designed to maintain the
temperature at or near 0°F (-17.8°C) under normal operating
conditions.
■Allow the freezer to cool 6 to 8 hours before filling with frozen
food.
A
C
B
A. Brake foot
B. Front roller
C. 1/4" hex driver
OPERATING YOUR FREEZER
9
■When the freezer is first started, the compressor will run
constantly until the freezer is cooled. It may take up to
6 or 8 hours (or longer), depending on room temperature and
number of times the freezer door is opened. After the freezer
is cooled, the compressor will turn on and off as needed to
keep the freezer at the proper temperature.
■The outside of your freezer may feel warm. This is normal.
The freezer’s design and main function is to remove heat
from packages and airspace inside the freezer. The heat is
transferred to the room air, making the outside of the freezer
feel warm.
Adjusting Control
If you need to adjust the temperature in the freezer
compartment, press TEMP SETTING to display the desired
temperature setting from the snowflake on the left (least cold) to
the snowflake on the right (coldest).
NOTE: Except when starting the freezer, do not adjust the
control more than one setting at a time. Wait 24 hours between
adjustments for the temperature to stabilize.
Cooling On/Off
Your freezer will not cool when cooling is turned off.
To turn cooling off, press and hold TEMP SETTING for
3 seconds. In the Off condition, none of the lights on the control
panel will be illuminated. The main freezer light bulb will still
operate.
To turn cooling on, press and hold TEMP SETTING for 3
seconds. When cooling is On, the control panel lights will be
illuminated.
Fast Freeze
Use this feature before adding large amounts of unfrozen food.
For the best food quality, do not exceed 3 lbs (1,361 g) per cu. ft
(28.32 L) of freezer space.
To activate Fast Freeze, press TEMP SETTING until all the
snowflake positions are illuminated simultaneously.
The freezer will remain in the Fast Freeze setting for 24 hours
after the extra-low temperature is reached. Once the time has
expired, the freezer will return to the previous temperature set-
ting. Fast Freeze may be manually turned off by pressing
TEMP SETTING to select the desired temperature setting from
the snowflake on the left (least cold) to the snowflake on the
right (coldest).
Over Temperature Alert (on some models)
The Over Temperature Alert lets you know if the freezer
temperature has risen to 19°F (-7°C) or higher. This alert feature
will sound a continuous alert tone and repeatedly flash a red
light on the control panel. The tone can be turned off by pressing
TEMP SETTING on the control panel once. As you press
TEMP SETTING, the red light will then also change from flashing
to continuously illuminated. The red light will remain illuminated
until the freezer temperature falls below 19°F (-7°C).
NOTE: If the red light on the control panel is repeatedly flashing,
but the alert tone is not sounding, this means that an
overtemperature condition has occurred, but the freezer tem-
perature has since returned to below 19°F (-7°C). To turn off the
red light indicator for this condition, press TEMP SETTING on
the control panel once.
Door Ajar Alarm (on some models)
The Door Ajar alarm lets you know when the freezer door has
been open for 5 minutes or longer and the cooling is turned on.
This alarm feature will sound an alert tone that will repeat every
2 minutes. Close the door to turn off the tone. The feature is
reset and will reactivate when the door is again left open for 5
minutes.
NOTE: To mute the alert tone while keeping the door open, such
as while cleaning the inside of the freezer, press TEMP SETTING
on the control panel. The alert tone will be temporarily turned off.
Key Eject Lock (on some models)
To lock or unlock the freezer, you must hold
the key in the lock while turning. The lock is
spring loaded, so the key cannot be left in the
lock.
If the key is lost, contact your dealer for a
replacement. Always give the model and
serial number of your freezer when
requesting a replacement key.
NOTE: Keep the key out of the reach of
children. Do not keep the key close to the
freezer/refrigerator.
Ice Maker (on some models)
To Turn the Ice Maker On/Off
NOTE: Do not force the wire shut-off arm up or down.
■To turn the ice maker on, simply lower the wire shut-off arm.
NOTE: Your ice maker has an automatic shutoff. As ice is
made, the ice cubes fill the ice storage bin and the ice cubes
will raise the wire shut-off arm to the Off (arm up) position.
■To manually turn the ice maker off, lift
the wire shut-off arm to the Off (arm up)
position and listen for the click to make
sure the ice maker will not continue to
operate.
Ice Production Rate
The ice maker should produce approximately 7 to 9 batches of
ice in a 24-hour period. If ice is not being made fast enough,
press TEMP SETTING to display the next colder setting. Wait
24 hours and, if necessary, set the temperature control to the
highest setting, waiting 24 hours between each increase.
Remember
■Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
■The quality of your ice will be only as good as the quality
of the water supplied to your ice maker. Avoid connecting
the ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice
maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.
■Do not store anything on top of the ice maker or in the ice
storage bin.
Freezer Features
This manual covers several different models. The freezer you
have purchased may have some or all of the items listed. The
locations of the features may not match those of your model.
Door Bin
To Remove and Replace the
Bin:
1. Remove the bin by tipping
the front of the bin forward
and sliding out.
2. Replace the bin by sliding it
in above the desired support,
tilting it back into place.
10
Storage Basket (on some models)
The slide-out basket provides separate
storage space for items that are difficult
to store on freezer shelves. To remove
the basket, pull out and lift up.
Storage Gate (on some models)
To Remove the Storage Gate:
1. Lift up the top of the gate and out of
the supports.
2. Return the gate to original position. Lower the gate into the
supports.
Freezer Shelves
Store similar foods together and adjust the shelves to fit
different heights. This reduces the time the freezer door is open
and saves energy.
To Remove and Replace a Shelf:
1. Remove the shelf by lifting straight up and pulling the shelf
out.
2. Replace the shelf by lowering the shelf onto the supports on
the side wall.
Cleaning Your Frost-Free Freezer
Frost-free means that you will not have to defrost your freezer.
Frost is removed by air moving and collecting any moisture and
depositing it on the cooling coil. The cooling coil periodically
warms up enough to melt the frost, and it then flows down to the
drain pan (located behind the base grille) where it is evaporated.
Complete cleaning should be done at least once a year.
1. Press and hold TEMP SETTING for 3 seconds to turn off
cooling.
2. Unplug freezer or disconnect power.
3. Remove all frozen food. Wrap frozen food in several layers
of newspaper and cover with a blanket. Food will stay frozen
for several hours. You may also store frozen food in a cooler,
additional refrigerator-freezer, or in a cool area.
4. Remove all removable parts from inside, such as shelves,
bins, etc.
5. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
■Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners, or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.
■To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda
(2 tbs to 1 qt [26 g to 0.95 L] of water).
6. Replace the removable parts.
7. Use the appropriate cleaning method for your exterior nish.
Painted metal: Wash exteriors with a clean sponge or
soft cloth and a mild detergent in warm water. Do not use
abrasive or harsh cleaners or cleaners designed for stainless
steel. Dry thoroughly with a soft cloth.
8. Clean the condenser coils regularly. Coils may need to be
cleaned as often as every other month. This may help save
energy.
■Open the freezer door and remove the base grille by
removing 2 Phillips-head screws and pulling the grille
toward you.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
CARING FOR YOUR FREEZER
11
■Use a vacuum with an extended attachment to clean the
condenser coils when they are dusty or dirty.
■Replace the base grille by aligning the ends of the grille
with the leveling assemblies on each side and snapping
the grille into place. Reinstall the screws.
9. Replace all frozen food.
10. Plug in freezer or reconnect power.
11. Set temperature control to desired setting. See “Using the
Control.”
Changing the Light Bulb(s) (on some models)
IMPORTANT: The lighting system in this appliance may
consist of:
■Sealed LED modules
■LED Bulbs
■Incandescent Bulbs
Sealed LED module is an LED which does not need to be
replaced. If a Sealed LED module(s) do not illuminate when the
refrigerator and/or freezer door is opened, call for assistance or
service. See “Warranty” for contact information.
If a LED Bulb does not illuminate when the refrigerator and/
or freezer door is opened, replace with like bulb following this
procedure:
1. Unplug appliance or disconnect power.
2. Remove the light shield.
■Remove the hardware holding the light shield in place.
■Top of the appliance compartment - Slide the light shield
toward the back of the compartment to release it from
the light assembly.
3. Replace the burned-out bulb(s) with a LED bulb of the same
size, shape and wattage.
■Order Part Number W10805744 (3.6 W).
NOTE: Some LED replacement bulbs are not recommend-
ed for wet/damp environments. The refrigerator and freezer
compartments are considered to be wet/damp environments.
If using a brand of LED bulb other than the recommended
LED bulb, before installation, read and follow all instructions
on the LED packaging.
4. Replace the light shield by inserting the tabs on the shield
into the liner holes on each side of the light assembly. Slide
the shield toward the front until it locks into place.
NOTE: To avoid damaging the light shield, do not force the
shield beyond the locking point.
5. Replace the hardware that holds the shield in place.
6. Plug in the appliance or reconnect power.
If an incandescent bulb does not illuminate when the refrigerator
and/or freezer door is opened, replace with like bulb using the
same procedure outlined above. Replace burned out bulb with
only incandescent bulb(s) of the same size, shape and wattage
(maximum 40 W) designed for household appliances.
Power Interruptions
If the power will be out for 24 hours or less, keep the door
closed to help food stay cold and frozen.
If the power will be out for more than 24 hours, do one of the
following:
■Remove all frozen food and store it in a frozen food locker.
■If a food locker is not available, consume or can perishable
food at once.
REMEMBER: A full freezer stays cold longer than a partially
filled one. A freezer full of meat stays cold longer than a freezer
full of baked goods. If you see that food contains ice crystals, it
may be refrozen, although the quality and flavor may be affected.
If the condition of the food is poor, dispose of it.
Moving Care
When you are moving your freezer to a new home, follow these
steps to prepare it for the move:
1. Remove all frozen food.
2. Unplug the freezer.
3. Take out all removable parts, wrap them well, and tape them
together so they don’t shift and rattle during the move.
4. Clean the freezer thoroughly.
5. Tape the freezer shut and tape the electrical cord to the
cabinet.
When you get to your new home, refer to the “Installing Your
Freezer” and “Operating Your Freezer” sections for information
on installation and setting the controls.
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,
refer to the warranty page in this manual, or visit www.whirlpool.com/product_help for recommendations that may help you avoid a
service call. In Canada, visit http://www.whirlpool.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
In Canada:
Whirlpool Brand Home Appliances
Customer eXperience Centre
200 – 6750 Century Ave.
Mississauga ON L5N 0B7
Please include a daytime phone number in your correspondence.
TROUBLESHOOTING
12
Freezer Operation
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
PROBLEM RECOMMENDED SOLUTIONS
Freezer Will Not Operate Check that it is plugged into a grounded 3 prong outlet.
Check that the temperature control is turned on.
Replace the fuse or reset the circuit breaker.
NOTE: If problems continue, contact an electrician.
Lights Do Not Work Check that it is plugged into a grounded 3 prong outlet.
Check that the light bulb is tight in the socket and is not burned out.
Water in Defrost Drain Pan It is normal for water to drip into the defrost drain pan when freezer is defrosting.
When humidity is high, it is normal for water in the defrost pan to take longer to evaporate.
Motor seems to run
too much Check that lid closes properly.
Defrost and clean the freezer to remove excessive frost.
Adding a large amount of food warms the freezer causing the freezer to run longer to cool back
down. If this is the situation, wait approximately 6 to 8 hours to allow the freezer to reach the
correct temperature.
Get all items out at one time, keep food organized and close door as soon as possible.
Check that the lid gasket is sealed all the way around. If not, contact a qualified person or
technician.
Check that space around freezer meets air circulation requirements. See “Location
Requirements.”
NOTE: If none of the above, your new freezer will run longer than your old one due to its
high-efficiency motor.
Temperature is too warm Get all items out at one time, keep food organized and close door as soon as possible.
Adding a large amount of food warms the freezer causing the freezer to run longer to cool back
down.
Check that the temperature control is set correctly for surrounding conditions.
The Lid Will Not Close
Completely or Is Difficult To
Open
Check that there are no food packages blocking the door.
On some models, check that the shelves and basket are in the correct position.
Check that gaskets are clean. See “Caring for Your Freezer.”
Check that the freezer is stable. See “Location Requirements.”
Freezer Makes Loud Buzzing/
Clicking Sound If the freezer has recently been plugged in or turned on following a defrost or product move, or if
there has been an extended power failure, turn off the temperature alarm for the next 24 hours.
Adding a large amount of food warms the freezer. It can take several hours for the freezer to
return to normal temperature. Turn the temperature alarm off for the next 24 hours.
13
PROBLEM RECOMMENDED SOLUTIONS
Ice Maker Produces No Ice
or Very Little Ice If ice maker has just been installed, wait 72 hours for full ice production to begin.
Check that the temperature control is cold enough.
Check that the wire shut-off arm is in the On (arm down) position.
Check that the water supply is properly connected and turned on.
Check that the ejector arm is not blocked by an ice cube.
If a large amount of ice has been removed recently, allow 24 hours to produce more ice.
NOTE: If not due to any of the above, there may be a problem with the water line. Call for service.
PROBLEM RECOMMENDED SOLUTIONS
Off Taste, Odor, or Gray
Color in the Ice Discard the first few batches of ice.
If there is unusually high mineral content in the water supply, the water may need to be treated.
If there is mineral scale buildup, clean your ice maker mold.
If the ice cubes have been stored too long, throw the old ice away and make a new supply.
Check that the freezer and ice bin are clean.
Thin, Soft, or Clumps of Ice If there is unusually high mineral content in the water supply, the water may need to be treated.
If there is mineral scale buildup, clean your ice maker.
If there are clumps of ice in the bin and if ice is not used regularly, it will melt and form clumps.
Break the clumps with the ice scoop provided.
Ice Production
Ice Quality
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
14
03/17
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed without
service. Please take a few minutes to review the Troubleshooting section of the Use and Care Guide or visit producthelp.whirlpool.com.
2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S. and Canada, direct all requests for
warranty service to:
Whirlpool Customer eXperience Center
In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.
If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.
WHIRLPOOL®
MAJOR APPLIANCE
LIMITED WARRANTY
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED
TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
Customer eXperience Center:
■Name, address, and telephone number
■Model number and serial number
■A clear, detailed description of the problem
■Proof of purchase, including dealer or retailer name and address
ONE YEAR LIMITED WARRANTY
WHAT IS COVERED WHAT IS NOT COVERED
For one year from the date of purchase,
when this major appliance is installed,
operated, and maintained according
to instructions attached to or furnished
with the product, Whirlpool Corporation
or Whirlpool Canada LP (hereafter
“Whirlpool”) will pay for factory
specified replacement parts and repair
labor to correct defects in materials or
workmanship that existed when this
major appliance was purchased or, at
its sole discretion, replace the product.
In the event of product replacement,
your appliance will be warranted for
the remaining term of the original unit’s
warranty period.
YOUR SOLE AND EXCLUSIVE
REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE PRODUCT
REPAIR AS PROVIDED HEREIN.
Service must be provided by a
Whirlpool designated service company.
This limited warranty is valid only in
the United States or Canada and
applies only when the major appliance
is used in the country in which it was
purchased. This limited warranty is
effective from the date of original
consumer purchase. Proof of original
purchase date is required to obtain
service under this limited warranty.
1. Commercial, non-residential, multiple-family use, or use inconsistent with published user, operator,
or installation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or installation, installation not in accordance with
electrical or plumbing codes, or correction of household electrical or plumbing (e.g., house wiring,
fuses, or water inlet hoses).
4. Consumable parts (e.g., light bulbs, batteries, air or water filters, preservation solutions).
5. Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.
6. Conversion of products from natural gas or propane gas.
7. Damage from accident, misuse, abuse, fire, floods, acts of God, or use with products not approved
by Whirlpool.
8. Repairs to parts or systems to correct product damage or defects caused by unauthorized service,
alteration, or modification of the appliance.
9. Cosmetic damage including scratches, dents, chips, and other damage to the appliance finishes,
unless such damage results from defects in materials and workmanship and is reported to Whirlpool
within 30 days.
10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive environments including,
but not limited to, high salt concentrations, high moisture or humidity, or exposure to chemicals.
11. Food or medicine loss due to product failure.
12. Pickup or delivery. This product is intended for in-home repair.
13. Travel or transportation expenses for service in remote locations where an authorized Whirlpool
servicer is not available.
14. Removal or reinstallation of inaccessible appliances or built-in fixtures (e.g., trim, decorative panels,
flooring, cabinetry, islands, countertops, drywall) that interfere with servicing, removal, or replacement
of the product.
15. Service or parts for appliances with original model/serial numbers removed, altered, or not easily
determined.
The cost of repair or replacement under these excluded circumstances shall be borne by
the customer.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow
limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific
legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations
contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,
you should ask Whirlpool or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES: EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of
incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you
also may have other rights that vary from state to state or province to province.
15
Nous vous REMERCIONS d’avoir acheté ce produit de grande qualité. Enregistrez votre congélateur au www.whirlpool.com.
Au Canada, enregistrez votre congélateur au www.whirlpool.ca.
Pour référence future, veuillez prendre en note les numéros de modèle et de série de votre produit. Ces numéros se trouvent à
l’intérieur du congélateur.
Numéro de modèle___________________________________________
Numéro de série_____________________________________________
Guide d’utilisation
Congélateur vertical
SÉCURITÉ
TABLE DES MATIÈRES
SÉCURITÉ ................................................................................ 15
Mise aux rebuts du vieux congélateur ou réfrigérateur ............. 16
INSTALLATION DE VOTRE CONGÉLATEUR ......................... 17
Déballage .................................................................................. 17
Exigences d’emplacement ........................................................ 17
Spécifications électriques ......................................................... 18
Ensemble de machine à glaçons .............................................. 18
Spécifications de l’alimentation en eau
(sur certains modèles) ............................................................... 18
Raccordement à la canalisation d’eau
(sur certains modèles) ............................................................... 19
Retrait et réinstallation de la poignée ........................................ 19
Porte du congélateur ................................................................. 19
Nivellement du congélateur et fermeture de la porte ................ 21
UTILISATION DE VOTRE CONGÉLATEUR ............................. 22
Pour assurer une circulation d’air correcte ............................... 22
Utilisation de la commande ....................................................... 22
Serrure à éjection de clé (sur certains modèles) ....................... 23
Machine à glaçons (sur certains modèles) ................................ 23
Caractéristiques du congélateur ............................................... 24
ENTRETIEN DU CONGÉLATEUR............................................ 25
Nettoyage du congélateur sans givre ........................................ 25
Remplacer l’ampoule (sur certains modèles) ............................ 25
Pannes de courant .................................................................... 26
Précautions à prendre avant un déménagement ...................... 26
DÉPANNAGE ............................................................................ 26
Fonctionnement du congélateur ............................................... 27
Production de glaçons .............................................................. 28
Qualité des glaçons ................................................................... 28
GARANTIE ................................................................................ 29
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :
16
Mise aux rebuts du vieux congélateur
ou réfrigérateur
IMPORTANT: Le risque qu’un enfant puisse se retrouver coincé
et suffoquer n’est pas chose du passé. Les réfrigérateurs et
congélateurs jetés ou abandonnés sont toujours dangereux,
même s’ils ne restent à l’extérieur que pour «quelques jours
seulement». Si vous vous débarrassez de votre vieux réfrigéré
ou congélateur, veuillez suivre les instructions suivantes pour
aider à éviter les accidents.
Avant de jeter votre vieux réfrigérateur
ou congélateur:
■Enlever les portes.
■Laisser les tablettes en place de sorte
que les enfants ne puissent pas y
pénétrer facilement.
AVERTISSEMENT :
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
CONSERVEZ CES INSTRUCTIONS
Brancher sur une prise de terre (reliée à la masse).
Ne pas retirer la broche de terre.
Ne pas utiliser d’adaptateur.
Ne pas utiliser de rallonge.
Débrancher la source de courant électrique avant l'entretien.
Replacer pièces et panneaux avant de faire la remise en
marche.
Enlever les portes de votre vieux l’appareil.
Utiliser un produit de nettoyage ininflammable.
Ne pas utiliser ou conserver d’essence ni de liquides ou gaz
inflammables à proximité de cet ou d’autres appareils
électriques. Les fumées peuvent causer des incendies ou
des explosions.
Utiliser deux ou plus de personnes pour déplacer et installer
le l’appareil.
Débrancher la source de courant électrique avant d’installer
la machine à glaçons (sur les modèles avec machine à
glaçons prête-à-installée uniquement)
L’ensemble de machine à glaçons ECKMF95 peut être
ajouté à certains modèles.
Un technicien qualifié doit installer le tuyau d’eau et le
distributeur de glaçons.Consulter les instructions
d’installation fournies avec la trousse de machine à glaçons
ECKMF95 pour tous les détails.
■ Raccorder uniquement à une arrivée d’eau potable.
Cet appareil ne convient pas à une utilisation par des
personnes (y compris des enfants) à capacités physiques,
sensorielles ou mentales réduites, ou possédant un
manque d’expérience et de connaissances, à moins
qu’elles ne soient placées sous supervision ou qu’elles
aient reçu des instructions concernant l’utilisation de
l’appareil par une personne responsable de leur sécurité.
Les enfants doivent être placés sous surveillance afin de
s’assurer qu’ils ne jouent pas avec l’appareil.
Si le cordon d’alimentation est endommagé, il doit être
remplacé par le fabricant, son agent de réparation ou
toute autre personne qualifiée afin d’éviter tout danger.
Ne pas entreposer de substances explosives comme des
aérosols avec agent propulseur inflammable dans cet
appareil.
Cet appareil est destiné à un usage domestique et à
d’autres usages similaires comme :
- espace de cuisine pour personnel de boutiques, bureaux
et autres environnements professionnels;
- résidences fermières et utilisation par les clients d’hôtels,
de motels et d’autres types de résidences;
- environnements de type chambres d’hôtes;
- Banquets et autres utilisations non commerciales
semblables.
Pour réduire le risque d’incendie, de choc électrique ou de blessure dans le cadre de l’utilisation
du l’appareil, suivre les consignes de base suivantes :
AVERTISSEMENT
Risque de suffoquer
Enlever les portes ou le couvercle de votre vieux
congélateur ou réfrigérateur.
Le non-respect de cette instruction peut causer
un décès ou des lésions cérébrales.
Renseignements importants à propos de la mise au
rebut des fluides réfrigérants :
Mettre le congélateur au rebut conformément à la
réglementation fédérale et locale. Les fluides réfrigérants
doivent être évacués par un technicien certifié et agréé par
l’EPA conformément aux procédures établies.
17
Déballage
Enlever les matériaux d’emballage
■Enlever tout résidu de ruban adhésif et de colle des surfaces
avant de le mettre en marche votre congélateur. Frotter une
petite quantité de savon liquide à vaisselle sur l’adhésif avec
les doigts. Rincer à l’eau tiède et sécher.
■Ne pas utiliser d’instruments coupants, d’alcool à friction,
de liquides inflammables ou de nettoyants abrasifs pour
enlever le ruban adhésif ou la colle. Ces produits peuvent
endommager la surface de votre congélateur. Pour obtenir
plus de renseignements, consulter la section «Sécurité».
Nettoyage avant utilisation
Après avoir enlevé tous les matériaux d’emballage, nettoyer
l’intérieur du congélateur avant de l’utiliser. Voir les instructions
de nettoyage dans la section «Entretien de votre congélateur».
Exigences d’emplacement
Ventilation et espace libre
■Garder les matières et vapeurs inflammables, telles que
l’essence, loin du congélateur.
■Ne pas couvrir le congélateur d’un drap, d’une couverture,
d’une nappe, etc. pour ne pas réduire la circulation d’air.
■Laisser au minimum 3po (7,5cm) d’espace au-dessus et
des deux côtés du congélateur et 1po (2,5cm) entre l’arrière
du congélateur et le mur. Si le congélateur doit être placé
près d’un mur fixe, laisser un espace supplémentaire côté
charnière pour que la porte puisse s’ouvrir en plus grand.
Température
Le congélateur fonctionne à son efficacité maximale lorsqu’il
se trouve dans un endroit où la température ne descend pas
en dessous de 40°F (5°C). Installer le congélateur dans un
endroit où la température ne descend pas en dessous de cette
température recommandée.
Lors du déplacement à l’emplacement final
REMARQUE: Laisser 3po (7,5cm) d’espace au-dessus et des
deux côtés et 1po (2,5cm) entre l’arrière et le mur.
AVERTISSEMENT
Risque du poids excessif
Utiliser deux ou plus de personnes pour déplacer et
installer le congélateur.
Le non-respect de cette instruction peut causer
une blessure au dos ou d'autre blessure.
Déplacement de votre congélateur :
Votre congélateur est lourd. Lors du déplacement de votre
congélateur pour le nettoyage ou un entretien, veiller à
recouvrir le plancher avec du carton ou un panneau de fibre
dur pour éviter qu'il ne subisse tout dommage. Toujours
tirer le congélateur tout droit lors du déplacement. Ne pas
incliner le congélateur d’un côté ou de l’autre ni le “faire
marcher” en essayant de le déplacer car le plancher pourrait
être endommagé.
Importants renseignements à savoir au sujet des tablettes
et des couvercles en verre :
Ne pas nettoyer les tablettes ou couvercles en verre avec de
l’eau tiède quand ils sont froids. Les tablettes et les
couvercles peuvent se briser s'ils sont exposés à des
changements soudains de température ou à un impact tel
que coup brusque. Le verre trempé est conçu pour éclater
en d’innombrables pièces minuscules. Ceci est normal. Les
tablettes et les couvercles en verre sont lourds. Les saisir à
deux mains lors de leur dépose afin d'éviter de les faire
tomber.
Risque d'explosion
Garder les matériaux et les vapeurs inflammables, telle
que l'essence, loin du congélateur.
Le non-respect de cette instruction peut causer
un décès, une explosion ou un incendie.
AVERTISSEMENT
3po (7,5cm)
3po (7,5cm)
INSTALLATION DE VOTRE CONGÉLATEUR
18
Spécifications électriques
Avant de déplacer le congélateur à son emplacement final, il est
important de vous assurer d’avoir le raccordement électrique
approprié.
Méthode recommandée de liaison à la terre
Un circuit de 115V CA à 60Hz relié à la terre et protégé par un
fusible de 15A ou 20A est requis. Il est recommandé d’utiliser
un circuit distinct qui n’alimentera que le congélateur. Utiliser
une prise de courant dont l’alimentation ne peut pas être
interrompue par un interrupteur. Ne pas utiliser de rallonge.
REMARQUE: Avant d’exécuter tout type d’installation, de
nettoyage ou de remplacement d’ampoule d’éclairage, maintenir
enfoncé le bouton TEMP SETTING (reglage de la temperature)
pendant 3 secondes pour désactiver le refroidissement, puis
débrancher le congélateur de sa source d’alimentation
électrique.
Ensemble de machine à glaçons
L’ensemble de machine à glaçonsECKMF95 peut être ajouté à
certains modèles.
REMARQUE:
■Suivre les instructions d’installation incluses avec
l’ensemble de machine à glaçons.
■Brancher à une alimentation en eau potable uniquement.
Spécifications de l’alimentation en eau
(sur certains modèles)
Rassembler les outils et pièces nécessaires avant d’entreprendre
l’installation. Lire et observer les instructions fournies avec
chacun des outils de la liste ci-dessous.
Outils nécessaires
■Tournevis à lame plate
■Clés ouvertes de 7/16 po et
1/2 po ou 2 clés à molette
■Tourne-écrou de 1/4 po
■Foret de 1/4 po
■Perceuse sans fil
REMARQUE: Votre marchand de réfrigérateurs dispose d’une
trousse disponible avec un robinet d’arrêt à étrier de 1/4 po
(6,35mm), un raccord et un tuyau en plastique. Avant de faire un
achat, s’assurer que le robinet d’arrêt à étrier est conforme aux
codes locaux de plomberie. Ne pas employer de robinet d’arrêt
à étrier de 3/16 po (4,76mm) ou de type à percer – ils réduisent
le débit d’eau et s’obstruent plus facilement.
IMPORTANT:
■Brancher sur une alimentation en eau potable uniquement.
■Si on doit mettre en marche le réfrigérateur avant que la
canalisation d’eau ne soit connectée, désactiver la machine
à glaçons.
■Toutes les installations doivent être conformes aux exigences
des codes locaux de plomberie.
■Utiliser un tuyau en plastique et vérifier qu’il n’y a pas de
fuites. Installer des tuyaux de plastique seulement là où les
températures resteront au-dessus du point de congélation.
Pression d’eau
Une alimentation en eau froide avec une pression entre 207 et
827kPa (30 et 120lb/po²) est nécessaire pour faire fonctionner
le distributeur d’eau et la machine à glaçons. Pour toute
question au sujet de la pression de l’eau, consulter la section
«Dépannage» ou faire appel à un plombier qualifié agréé.
Alimentation en eau par osmose inverse
Si un système de purification de l’eau par osmose inverse est
raccordé à votre alimentation en eau froide, la pression de l’eau
à l’entrée du système doit être d’un minimum de 40 à 60lb/po²
(276 à 414kPa).
Si la pression de l’eau au système d’osmose inverse est
inférieure à une valeur entre 40 à 60lb/po² (276 à 414kPa), une
pompe de surpression peut être insérée sur le petit tuyau qui va
de la canalisation d’eau froide à l’entrée du système d’osmose
inverse.
Si le distributeur d’eau ne distribue toujours pas d’eau
correctement:
■Vérifier que le filtre à sédiment dans le système à osmose
inverse n’est pas obstrué. Remplacer le filtre si nécessaire.
■Laisser le réservoir du système d’osmose inverse se remplir
après une utilisation intense.
■Si le réfrigérateur comporte un filtre à eau, celui-ci peut
réduire la pression de l’eau lorsqu’il est utilisé avec un
système d’osmose inverse. Enlever le filtre à eau.
Pour toute question au sujet de la pression de votre eau,
consulter la section «Dépannage» ou faire appel à un plombier
qualifié agréé.
AVERTISSEMENT
Risque de choc électrique
Brancher sur une prise à 3 alvéoles reliée à la terre.
Ne pas enlever la broche de liaison à la terre.
Ne pas utiliser un adaptateur.
Ne pas utiliser un câble de rallonge.
Le non-respect de ces instructions peut causer
un décès, un incendie ou un choc électrique.
Ne pas utiliser pour le filtrage d'une eau
microbiologiquement polluée ou de qualité inconnue en
l'absence d'un dispositif de désinfection adéquat avant ou
après le système. Les systèmes certifiés pour la réduction
de kyste peuvent être utilisés pour l'eau désinfectée qui
peut contenir des kystes filtrables.
19
Raccordement à la canalisation d’eau
(sur certains modèles)
Raccordement à la canalisation d’eau
1. Débrancher le congélateur ou déconnecter la source de
courant électrique.
2. Couper l’alimentation principale en eau. Ouvrir le robinet le
plus proche assez longtemps pour vider l’eau du tuyau.
3. Trouver une canalisation d’eau froide verticale de 1/2 po
(12,7mm) à 1 ¼ po (3,18cm) près du réfrigérateur.
IMPORTANT:
■Vérifier qu’il s’agit d’une canalisation d’eau froide.
■On peut aussi utiliser une canalisation horizontale; dans
ce cas, on devra percer sur la face supérieure du tuyau
et non pas au-dessous. Ceci permet de tenir la perceuse
à l’écart de l’eau et d’empêcher les sédiments qu’on
trouve normalement dans l’eau de s’accumuler dans le
robinet d’arrêt.
4. Déterminer la longueur de tube de plastique à utiliser.
Mesurer la distance entre le raccord situé sur la partie
inférieure arrière gauche du congélateur et la canalisation.
Ajouter 7pieds (2,1m) pour permettre les opérations de
nettoyage. Utiliser un tube en cuivre de 1/4 po (6,35mm) de
diamètre externe.
Veiller à ce que le tube soit coupé d’équerre aux deux
extrémités.
5. À l’aide d’une perceuse sans fil, percer un trou de 1/4 po
(6,35mm) dans la canalisation d’eau froide sélectionnée.
6. Fixer le robinet d’arrêt sur la canalisation d’eau froide avec
la bride de tuyau. Veiller à bien insérer l’extrémité de sortie
dans le trou de 1/4 po (6,35mm) de la canalisation d’eau;
veiller à placer correctement le joint sous la bride du tuyau.
Serrer l’écrou de serrage. Serrer lentement et uniformément
les vis fixant la bride de tuyau sur le tuyau afin d’assurer
l’étanchéité du joint. Ne pas serrer excessivement, car ceci
pourrait provoquer l’écrasement du tube en plastique.
7. Enfiler la bague et l’écrou de compression sur le tube
en plastique comme illustré. Insérer l’extrémité du tube
directement dans l’extrémité de sortie, aussi loin que
possible. Visser l’écrou de compression sur l’extrémité de
sortie du raccord à l’aide d’une clé à molette.
Ne pas serrer excessivement.
8. Placer le bout libre du tube dans un contenant ou évier et
ouvrir le robinet principal d’alimentation en eau. Laisser
l’eau s’écouler par le tube jusqu’à ce qu’elle soit limpide.
Fermer le robinet principal d’arrivée d’eau. Enrouler le tube
de plastique.
Raccordement au congélateur
1. Fixer le tuyau en plastique au robinet d’arrivée d’eau à l’aide
d’un écrou et d’une bague de compression comme illustré.
Serrer l’écrou de compression. Ne pas serrer excessivement.
2. À l’aide de la bride du tuyau à l’arrière du congélateur, fixer
le tuyau au congélateur comme illustré. Ceci permet d’éviter
d’endommager le tuyau lorsque le congélateur est repoussé
contre le mur.
3. Ouvrir le robinet d’arrêt.
4. Vérifier qu’il n’y a pas de fuites. Serrer tous les raccords (y
compris les raccords du robinet) ou les écrous qui présentent
des fuites.
5. La machine à glaçons comporte un filtre à eau incorporé.
Si les caractéristiques de l’eau requièrent un second filtre à
eau, installer celui-ci dans la canalisation d’eau de 1/4 po
(6,35mm) à l’une ou l’autre des extrémités de la canalisation.
Se procurer un filtre à eau auprès de votre revendeur
d’appareils ménagers le plus proche.
6. Brancher l’appareil sur une prise à 3 alvéoles reliée à la terre.
Retrait et réinstallation de la poignée
Retrait de la poignée:
1. Desserrer les vis de blocage situées sur le côté de la poignée
à chaque extrémité. Voir l’illustration «Inversion du sens
d’ouverture de la porte et retrait de la poignée».
2. Retirer la poignée des œillets.
Réinstallation de la poignée:
1. Placer la poignée sur les œillets en s’assurant que les œillets
sont bien installés dans les trous de la poignée.
2. Serrer les vis de blocage supérieures et inférieures à
l’aide de la clé à tête hexagonale fournie. Voir l’illustration
«Inversion du sens d’ouverture de la porte et retrait de la
poignée». Ne pas serrer excessivement les vis de blocage.
Porte du congélateur
Outils requis: Clé à douille de 5/16po, clé à douille de 3/8po,
couteau à mastic plat de 2po.
IMPORTANT:
■Toutes les illustrations mentionnées dans les instructions
suivantes sont incluses plus loin dans cette section après
«Étapes finales». Les illustrations correspondent à une porte
s’ouvrant à droite (charnières installées à droite à l’usine).
A
B
C
DFE
G
A. Canalisation d’eau froide
B. Bride de tuyau
C. Tube de plastique
D. Écrou de compression
E. Bague de compression
F. Robinet d’arrêt
G. Écrou de garniture
A
C
B
D
E
A. Bride de tube
B. Vis de bride de tube
C. Tube de plastique
D. Écrou de compression
E. Robinet d’arrivée d’eau
AVERTISSEMENT
Risque de choc électrique
Brancher sur une prise à 3 alvéoles reliée à la terre.
Ne pas enlever la broche de liaison à la terre.
Ne pas utiliser un adaptateur.
Ne pas utiliser un câble de rallonge.
Le non-respect de ces instructions peut causer
un décès, un incendie ou un choc électrique.
20
■Pour seulement enlever et réinstaller la porte, voir
les sections «Démontage - Porte et charnières» et
«Réinstallation - Porte et charnières».
■Avant de commencer, fermer la commande et retirer les aliments
et tout balconnet réglable ou compartiment utilitaire de la porte.
Démontage – Porte et charnières
1. Débrancher le congélateur ou déconnecter la source de
courant électrique.
2. Laisser la porte du congélateur fermée jusqu’au moment de
la soulever pour la dégager de la caisse.
REMARQUE: Prévoir un support additionnel de la porte
pendant le déplacement des charnières. La force d’attraction
des aimants de porte ne suffit pas à la maintenir en place.
3. Enlever les pièces de la charnière supérieure – voir
l’illustration de la charnière supérieure à la section «Inversion
du sens d’ouverture de la porte et retrait de la poignée».
4. Soulever la porte du congélateur pour la séparer de la
charnière inférieure et de la caisse et la conserver à part.
5. Retirer les 4 vis de charnière à tête hexagonale et la
charnière inférieure. Voir l’illustration de la charnière
inférieure à la section «Inversion du sens d’ouverture de la
porte et retrait de la poignée».
Inversion du sens d’ouverture de la porte (facultatif –
sur certains modèles)
IMPORTANT: Pour inverser le sens d’ouverture de la porte,
suivre les instructions de la section «Inversion du sens
d’ouverture de la porte (facultatif – sur certains modèles)». S’il
n’est pas nécessaire de changer l’orientation de la porte, voir
«Réinstallation - Porte et charnières».
Caisse
1. Enlever les bouchons d’obturation des trous de charnière au
sommet de la caisse; transférer ceux-ci dans les trous de
charnière du côté opposé (voir l’illustration2 de la section
«Inversion du sens d’ouverture de la porte et retrait de la
poignée»).
2. Retirer l’axe de charnière inférieure de la bride de charnière.
3. Retirer les œillets recouvrant les trous du côté opposé de la
charnière inférieure.
4. Réinstaller l’axe de charnière dans l’autre trou de la bride
de charnière. Voir l’illustration3 de la section «Inversion du
sens d’ouverture de la porte et retrait de la poignée».
5. Réinstaller la bride de charnière sur la caisse à l’aide des 4
vis de charnière à tête hexagonale.
Porte
1. Enlever le bouchon d’obturation de la partie supérieure de
charnière au sommet de la porte.
2. Retirer la butée de porte du bas de la porte.
3. Placer la butée de porte du côté opposé en s’assurant que
le trou de la plaque de butée de porte est parfaitement
aligné avec le trou de la porte destiné à l’axe de charnière
inférieure.
4. À l’aide des vis retirées à l’étape2, fixer le support de butée
de porte au bas de la porte.
5. Serrer toutes les vis. Conserver la porte du congélateur à
part jusqu’à la mise en place de la charnière inférieure.
Réinstallation – Porte et charnières
REMARQUE: Si on inverse le sens d’ouverture de la porte,
considérer l’image symétrique.
1. Assembler les pièces de la charnière inférieure (comme
indiqué) et serrer les vis. Voir l’illustration de la charnière
inférieure. Réinstaller la porte du congélateur.
REMARQUE: Prévoir un support additionnel de la porte
pendant le déplacement des charnières. La force d’attraction
des aimants de porte ne suffit pas à la maintenir en place.
2. Assembler les pièces de la charnière supérieure – voir
l’illustration de la charnière supérieure à la section «Inversion
du sens d’ouverture de la porte et retrait de la poignée». Ne
pas complètement serrer les vis.
Étapes finales
1. Inspecter tous les trous. Vérifier que tous les bouchons
d’obturation et vis sont en place. Réinstaller le couvercle
de la charnière supérieure. Voir l’illustration de la charnière
supérieure.
2. À l’aide des œillets fournis, recouvrir les trous restants situés
sur le côté opposé de la charnière inférieure.
3. Brancher l’appareil sur une prise à 3 alvéoles reliée à la terre.
4. Réinitialiser la commande. Voir la section «Utilisation de la
commande».
5. Réinstaller toutes les pièces amovibles de la porte et
remettre les aliments dans le congélateur.
AVERTISSEMENT
Risque du poids excessif
Utiliser deux ou plus de personnes pour soulever la
porte du congélateur.
Le non-respect de cette instruction peut causer
une blessure au dos ou d'autre blessure.
Vis de charnière à tête hexagonale
AVERTISSEMENT
Risque de choc électrique
Déconnecter la source de courant électrique avant
d'enlever les portes.
Le non-respect de cette instruction peut causer
un décès ou un choc électrique.
AVERTISSEMENT
Risque de choc électrique
Brancher sur une prise à 3 alvéoles reliée à la terre.
Ne pas enlever la broche de liaison à la terre.
Ne pas utiliser un adaptateur.
Ne pas utiliser un câble de rallonge.
Le non-respect de ces instructions peut causer
un décès, un incendie ou un choc électrique.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
dans d''autres langues
- English: Whirlpool WZF56R16DW User guide
- español: Whirlpool WZF56R16DW Guía del usuario