WAC Lighting WS-45105 c Manuel utilisateur
- Taper
- Manuel utilisateur
1
INSTALLATION INSTRUCTION
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
‐ Read all instructions before installing.
‐ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
‐ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
‐ Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by
dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCENOTE:Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
‐ Lisez toutes les instructions avant l’installation.
‐ Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
‐ Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou
accessoires non conçus pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer
l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTED’ENTRETIEN:Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
Wire Connector
Qty: 3pcs+1 Extra
A
D
B
Mounting Screw
Qty:1 Extra
CE
Assembly Screw
Qty: 2pcs
Conversion Plate
Qty: 1pc
Mounting Ring
Qty: 1pc
HARDWARE
(WS-73118)
8
Black or
Smooth
White or
Ribbed
Bare wire
(Ground)
Black
(Hot)
White
(Neutral)
Green or Bare Copper
(Ground)
3000K3500K
2700K
Mounting Back Plate
53"
63
8"
(WS-73124)
23
8"
15
8"13
8"
GND
Mounting Ring
13
8"
13
4"
Ø4"
2
INSTALLATION INSTRUCTION
MOUNT ON SWITCH BOX
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
3. Remove the mounting screw (B) with screw driver.
4. The lamp can switch between three color temperatures (2700K-3000K-3500K), which can be adjusted to your preference with the switch
in the canopy (Fig.3).
5.
6. Connect the xture’s wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet box has a green
or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the back plate using
the GND screw provided. After wires are connected, tuck them carefully inside the junction box.
7. Secure the xture to the mounting back plate with the mounting screw(B).
(i) Secure the mounting ring (E) to the junction box using standard junction box screws that comes with the junction box.
(ii) Secure the mounting back plate and conversion plate (D) to the mounting ring with assembly screw (C).
(i) Using any other non-original-manufacturer provided junction box screws may result in safety issue.
NOTE:
MOUNT ON JUNCTION BOX
Secure the mounting back plate to the switch box using the screws provided with the switch box.
Conversion Plate
41
2"
7"
6"
15
8"13
8"
(WS-73118)
(WS-73124)
B
A
CD
E
B
MOUNT ON SWITCH BOX
Bare Copper
Ground Wire
Switch Box
Wire Connector
Mounting Screw
Black Wire
White Wire
Mounting
Back Plate
Switch
Box Screw
Black Wire
White Wire
Mounting Ring
Conversion
Plate
Assembly
Screw
Switch
Mounting
Back Plate
Junction
Box Screw
A
Wire Connector
Junction
Box
Bare Copper
MOUNT ON JUNCTION BOX
Screw
Mounting
Switch
Ground Wire
-
1
-
2
WAC Lighting WS-45105 c Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: WAC Lighting WS-45105 c User manual