Dacor DOB30P977SS Guide d'installation

Installation Manual

Built-In Electric Wall Oven

DOB30P977**

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 1 2020-06-24 �� 10:12:34

2 English

Contents / Before you begin...

Contents / Before you begin... Before you begin...

Important

Installer

• To promote safety and minimize problems, read this manual thoroughly before

starting the installation. Leave this manual with the user.

• Write the appliance’s model/serial numbers in this manual for service/

maintenance reference.

User

• Keep this manual for personal reference and for that of inspectors, service

personnel, etc.

Contents

Before you begin... 2

Important 2

Customer-service information 3

If You Need Help... 3

Safety informations 3

Related equipment safety 3

Transport 3

Preparation 5

Checklist 5

Prepare to install the oven 5

Location requirements 6

Product dimensions - single ovens 6

Cabinet dimensions - single ovens 7

Product dimensions - double ovens 8

Cabinet dimensions - double ovens 8

Installation instructions 11

Prepare built-in oven 11

Remove and replace oven door(s) 11

Electrical connection 13

Install oven 15

Self-diagnosis 16

Temp sensor & Heater check 16

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 2 2020-06-24 �� 10:12:34

English 3

Customer-service information / Safety informations

Customer-service information

If You Need Help...

If you have questions or problems with installation, contact your Dacor® dealer or

the Dacor Customer-Service team. If your Dacor appliance is under warranty, call

Dacor Distinctive Service. Have the appliance’s model/serial numbers available

when you call.

Dacor Customer Service

Phone: 833-35-ELITE (833-353-5483) (U.S.A. and Canada)

Monday — Friday 5:00 a.m. to 5:00 p.m. Pacic Time

Web site: www.dacor.com

All specications are subject to change without notice. Dacor assumes no liability

for changes to specications.

Safety informations

Related equipment safety

Remove all tape and packaging before using the appliance. Dispose of the

packaging after unpacking the appliance. Never allow children to play with

packaging material.

Never modify or alter the construction of the appliance. For example, do not

remove panels, wire covers or screws.

Transport

To avoid damage to the oven vent, use the transport method shown in the picture

below.

A

B

A. Front

B. Pallet

Support the bottom of the oven from either

side when moving it into the installation

location. Leave the unit attached to the

shipping pallet until it is in front of the

cabinet opening and is ready to be lifted

into place.

DANGER

ELECTRICAL SHOCK HAZARD

To avoid risk of electrical shock, personal injury or death; verify your appliance

has been properly grounded in accordance with local codes or in absence of codes,

with the National Electrical Code (NEC). ANSI/NFPA 70-latest edition.

WARNING

MOVING HAZARD

To avoid risk of severe personal injury; this appliance requires two or more people

while handling and moving. Use of appliance moving devices is recommended.

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 3 2020-06-24 �� 10:12:35

4 English

Safety informations

WARNING

• The information in this manual should be followed exactly.

• A re or electrical shock may result causing property damage, personal

injury or death.

• Important - Save this installation manual for local electrical inspector's use.

• Proper Installation - Be sure your appliance is properly installed and grounded

by a qualied technician.

• New branch-circuit installations (1996 NEC), mobile homes, recreational

vehicles, or installations where local codes prohibit grounding through the

neutral conductor require 4-wire branch-circuit connection.

• Improper connection of aluminum house wiring to copper leads can result in

an electrical hazard or re. Use only connectors designed for joining copper to

aluminum and follow the manufacturer’s recommended procedure closely.

• Mounting screws must be used.

• Failure to do so can result in the oven falling out of the cabinet causing

serious injury.

CAUTION

• Make sure the cabinets and wall coverings around the oven can withstand the

temperature (up to 194 °F [90 °C]) generated by the oven.

• Discoloration, delamination or melting may occur.

• DO NOT remove spacers on the side walls of the built-in oven.

• These spacers center the oven in the space provided. The oven must be

centered to prevent excess heat buildup that may result in heat damage

or re.

WARNING

• The information in this manual should be followed exactly.

• A re or electrical shock may result causing property damage, personal

injury or death.

IMPORTANT NOTE

Proper installation is the responsibility of the installer and product failure due to

improper installation is NOT covered under warranty.

WARNING

• DO NOT put any weight on the oven door. Never allow anyone to climb, sit,

stand or hang on the oven door.

• The oven could tip and injury might result from food or the oven itself.

WARNING

• The electrical power must be shut off while the electrical connections are

being made.

• Failure to do so can result in severe personal injury, death or electrical

shock.

IMPORTANT NOTE

• Observe all governing codes and ordinances. This appliance must be properly

grounded.

• Keep oven vent ducts unobstructed. The oven vent is located bottom of the

oven. This area could become hot during oven use. Never block this vent or

place plastic or heat-sensitive items in front of it.

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 4 2020-06-24 �� 10:12:35

English 5

Preparation

Checklist

Use this checklist to verify that you have completed each step of the installation

process. This can help you avoid mistakes.

1. Before installing the oven, be sure to verify the cabinet dimensions are correct

for your unit and the required electrical connections are present.

2. Refer to the installation manual for content regarding Safety, Cabinet

Dimensions, Removing Packaging, Electrical Installation, Testing the

Installation and Customer Service.

3. To lift up the oven, hang the install handle onto the side hook of the unit.

4. Move the oven unit into place in front of the cabinet opening, leaving the

bottom packaging on the unit to avoid damaging ooring.

5. Team lift the unit directly into the cabinet cutout taking care not to pinch

ngers or scratch hands or arms. Make sure the electrical conduit reaches to

the connection point properly.

6. Slide the unit all the way into place, making sure to route the electrical conduit

correctly.

7. Fasten the oven unit to the cabinetry opening with screws supplied (using

Phillips screwdriver).

8. Consult the complete installation instructions and follow the remainder of the

procedures listed, including performing an operation test.

9. All product literature and accessories are supplied (may be wrapped or boxed)

with the oven.

10. INSTALLER - Leave the literature pack and the accessories with the customer.

11. Hang the install handle onto the side hook of the oven.

Prepare to install the oven

Phillips Screwdriver Drill

Prepare to install the oven

6 screws (M4 L16)

6 Wood Screw For Mounting

(4 needed for Single ovens and 6 needed

for double ovens)

Install Handle

(only for double oven)

Materials needed

Junction Box Wire Nuts 3/4” Conduit Connector

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 5 2020-06-24 �� 10:12:35

6 English

Preparation

Location requirements

IMPORTANT: Observe all governing codes and ordinances.

• Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance with oven.

• Recessed installation area must provide complete enclosure around the

recessed portion of the oven.

• Grounded electrical supply is required. See “Electrical Requirements”

section.

• Electrical supply junction box should be located 3” (76 mm) maximum below

the support surface when the oven is installed in a wall cabinet. A 1” (26 mm)

minimum diameter hole should have been drilled in the right rear or left

rear corner of the support surface to pass the appliance cable through to the

junction box.

NOTE

For under counter installation, it is recommended that the junction box be located

in the adjacent right or left cabinet. If you are installing the junction box on rear

wall behind oven, it is recommended that the junction box be recessed and located

in the upper Right of the cabinet.

• Oven support surface must be solid, level and ush with bottom of cabinet

cutout.

• Floor must be able to support a single oven weight of 199 lb (90 Kg).

• Floor must be able to support a double oven weight of 331 lb (150 Kg).

IMPORTANT: To avoid damage to your cabinets, check with your builder or

cabinet supplier to make sure that the materials used will not discolor, delaminate

or sustain other damage. This oven has been designed in accordance with the

requirements of UL and CSA International and complies with the maximum

allowable wood cabinet temperatures of 194 °F (90 °C).

Product dimensions - single ovens

287/8”

(731 mm)

271/4”

(691 mm)

31/2”

(89 mm)

293/4” (756 mm)

Front view

231/8” (587 mm)

Side view

13/8” (33 mm)

28/”

(724 mm)

47/” (1200 mm)

Conduit length

Top view

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 6 2020-06-24 �� 10:12:35

English 7

Preparation

Cabinet dimensions - single ovens

Standard cabinet dimensions

01 Dimensions provide minimum reveals. (except electrical supply location ‘E’)

02 Allow a minimum of 22”

(559 mm)

for clearance to adjacent corners, drawers,

walls, etc. when door is open.

231/2”

(597 mm)

281/2”

(724 mm)

1” (26 mm)

195/8”

(498 mm)

1” (26 mm)

11/8” (28 mm)

11/2” (38 mm)

Top view Top view

(Cooktop installation)

Side view Front view

271/4”

(692 mm) 281/2”

(724 mm)

Min. 22”

(559 mm)

Max. 91/2” (241 mm)

5” (127 mm)

4” (101 mm)

For cooktop

installation

Flush cabinet dimensions

01 Dimensions provide minimum reveals. (except electrical supply location ‘E’)

02 Allow a minimum of 22”

(559 mm)

for clearance to adjacent corners, drawers,

walls, etc. when door is open.

03 Flush installation requires recessed strips (not included) attached to the side of

the cabinet opening for mounting the oven.

247/8”

(630 mm)

281/2”

(724 mm)

1” (26 mm)

195/8”

(498 mm)

1” (26 mm)

1/” (33 mm)

11/8” (28 mm)

11/2” (38 mm)

Top view Top view

(Cooktop installation)

Side view Front view

29” (737 mm)

7/8” (20 mm) Cleat width

301/4”

(767 mm)

Min. 22”

(559 mm)

Max. 91/2” (241 mm)

5” (127 mm)

21/4” (57 mm)

For cooktop

installation

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 7 2020-06-24 �� 10:12:36

8 English

Preparation

Cabinet dimensions - double ovens

Standard cabinet dimensions

01 Dimensions provide minimum reveals. (except electrical supply location ‘E’)

02 Allow a minimum of 22”

(559 mm)

for clearance to adjacent corners, drawers,

walls, etc. when door is open.

281/2”

(724 mm)

231/2”

(597 mm)

501/4”

(1276 mm)

12”

(305 mm)

Min. 47”

(1194 mm)

Top view

Side view Front view

Max. 91/2” (241 mm)

Product dimensions - double ovens

511/2”

(1307 mm)

497/8”

(1267 mm)

31/2”

(89 mm)

293/4” (756 mm)

Front view

231/8” (587 mm)

Side view

13/8” (33 mm)

28/”

(724 mm)

67” (1700 mm)

Conduit length

Top view

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 8 2020-06-24 �� 10:12:36

English 9

Preparation

If codes permit and a separate ground wire is used, it is recommended that a

qualied electrical installer determine that the ground path and the wire gauge are

in accordance with local codes.

Check with a qualied electrical installer if you are not sure the oven is properly

grounded.

This oven must be connected to a grounded-metal permanent wiring system.

Be sure that the electrical connection and wire size are adequate and in

conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA

Standards C22.

1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all

local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Flush cabinet dimensions

01 Dimensions provide minimum reveals. (except electrical supply location ‘E’)

02 Allow a minimum of 22”

(559 mm)

for clearance to adjacent corners, drawers,

walls, etc. when door is open.

03 Flush installation requires recessed strips (not included) attached to the side of

the cabinet opening for mounting the oven.

301/4”

(767 mm)

247/8”

(630 mm)

517/8”

(1316 mm)

12”

(305 mm)

Min. 47”

(1194 mm)

Top view

Side view Front view

Max. 91/2” (241 mm)

13/8” (33 mm)

7/8” (20 mm) Cleat width

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 9 2020-06-24 �� 10:12:36

10 English

Preparation

Electrical Connection

To properly install your oven, you must determine the type of electrical connection

you will be using and follow the instructions provided in this manual.

• Oven must be connected to the proper electrical voltage and frequency as

specied on the model/serial/rating plate. The model/serial/rating plate is

located on the bottom left side of the trim. See the following illustrations.

A

Single Oven

A. Model/serial/rating plate

Double Oven

A. Model/serial/rating plate

• A circuit breaker is recommended.

• Use the chart below to determine the minimum recommended dedicated

circuit protection.

KW Rating (240 V) KW Rating (208 V) Recommended Circuit

Size (Dedicated)

≤4.8 KW ≤4.1 KW 20 Amp

4.9 KW - 7.5 KW 4.3 KW - 6.2 KW 30 Amp

7.3 KW - 9.6 KW 6.3 KW - 8.3 KW 40 Amp

9.7 KW - 12.0 KW 8.4 KW - 10.4 KW 50 Amp

• Connect directly to the circuit breaker box (or fused disconnect) through

exible, armored or nonmetallic sheathed, copper cable (with grounding wire).

See “Electrical Connection” section.

• Flexible conduit from the oven should be connected directly to the junction

box.

• Fuse both sides of the line.

• Do not cut the conduit. The length of conduit provided is for serviceability of

the oven.

• A UL listed or CSA approved conduit connector must be provided.

• If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the ends of the exible conduit

leads.

2. Connect the aluminum wiring to the added section of copper wire using

special connectors and/or tools designed and UL listed for joining copper

to aluminum.

Follow the electrical connector manufacturer's recommended procedure.

Aluminum/copper connection must conform with local codes and industry

accepted wiring practices.

For power requirements for models DOB30P977SS,DOB30P977DS refer to the

following table.

Model 240 VAC 208 VAC

Power Circuit Size Power Circuit Size

DOB30P977SS 5.6 kW 30 Amp 4.2 kW 30 Amp

DOB30P977DS 11.2 kW 50 Amp 8.4 kW 50 Amp

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 10 2020-06-24 �� 10:12:36

English 11

Installation instructions

Prepare built-in oven

WARNING

Excessive Weight Hazard

Use two or more people to move and install an oven.

Failure to do so can result in back or other injury.

1. Decide on the nal location for the oven. Avoid drilling or cutting into house

wiring during installation.

2. To avoid oor damage, set the oven on a cardboard prior to installation. Do

not use handle or any portion of the front frame for lifting.

3. Remove the shipping materials and tape from the oven.

Remember to keep the packing materials that may be needed for installation.

4. Remove the hardware package from inside of the bag containing literature.

5. Remove racks and other parts from inside the oven.

6. Move oven and cardboard close to the oven’s nal location.

Remove and replace oven door(s)

IMPORTANT: Use two hands to remove oven door. For double ovens, repeat the

process for each door.

Prior to removing the oven door, prepare a surface where you will place it. This

surface should be at and covered with a soft blanket, or use the corner posts

from your packaging material.

Disconnect LED light wire harness

Locate the LED light wire harness and disconnect it before removing the door.

Wire Harness

Single Oven Double Oven

1. Carefully pull the wire to reveal the

connector.

2. Disconnect the connector.

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 11 2020-06-24 �� 10:12:36

12 English

Installation instructions

Remove oven door(s)

AB

A. Oven door hinge lock in

locked position

B. Oven door hinge lock in

unlocked position

1. Open the oven door.

2. Locate the oven door hinge locks in

both corners of the oven door, and

then rotate the hinge locks toward the

oven door to the unlocked position (see

illustration B). If the door hinge lock

is not rotated fully, the door will not

remove properly.

3. Partially close the door to engage the

door latch locks.

The door will stop at this point.

4. Using two hands, grasp the edges of

the oven door. Lift and pull the oven

door toward you and remove. You may

need to gently shift door from side to

side as you pull.

5. Set the oven door(s) aside on the

prepared covered work surface with the

oven door resting on its handle.

6. To continue with the oven installation,

go to the “Positioning Oven Feet

for Multiple Cabinet Cutout Heights”

section.

Replace oven door(s)

CAUTION

The door is very heavy. You may need help lifting the door high enough to slide it

into the hinge slots. Do not lift the door by the handle.

A

A. Slot in the oven cavity for

door hinge lock

1. Using two hands, grasp side edges of

door at the midpoint.

Face the oven cavity.

2. Locate the slots on each side of the

oven cavity for the door hinge locks.

3. At a 45° angle, align door hinges with

slots in the lower front of the oven

cavity. Slowly insert door, making sure

you maintain the 45° angle. You will

know the door is engaged in the slot

when you feel a slight drop.

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 12 2020-06-24 �� 10:12:36

English 13

Installation instructions

4. Lower the oven door to the fully open

position. If the oven door does not open

to a full 90°, repeat steps 1 through 3.

5. Locate the oven door hinge locks in the

corners of the oven door, and rotate the

hinge locks toward the oven cavity to

the locked position.

See Step 1 (illustration A) in the

“Remove Oven Door(s)” section for

proper locked position.

6. Close the oven door.

7. When the hinges are properly installed

and the door closed, there should be

an even gap between the door and the

control panel. If one side of the oven

door is hanging lower than the other,

the hinge on that side is not properly

installed.

8. Connect Wire Harness.

Electrical connection

For Double Ovens

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge solid copper wire.

Make sure to ground the oven.

Failure to follow these instructions can result in death, re, or electrical shock.

This oven is manufactured with a neutral (white) power supply wire and a cabinet-

connected ground (green or bare) wire twisted together.

A

A. UL listed or CSA approved

conduit connector

1. Disconnect power.

2. Feed the exible conduit from the oven

through the opening in the cabinet.

3. Remove junction box cover if it is

present.

4. Install a UL listed or CSA approved

conduit connector to the junction box.

5. Route the exible conduit from the

oven to the junction box through a

UL listed or CSA approved conduit

connector.

6. Tighten screws on conduit connector.

7. See “Electrical Connection Options

Chart” to complete installation for your

type of electrical connection.

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 13 2020-06-24 �� 10:12:37

14 English

Installation instructions

Electrical Connection Options Chart

If your home has: Go to section:

4-wire

(1.3 cm)

½”

4-Wire Cable from Home Power Supply

3-wire

(1.3 cm)

½”

3-Wire Cable from Home Power Supply

For Single Ovens

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge solid copper wire.

Electrically ground oven.

Failure to follow these instructions can result in death, re, or electrical shock.

4-Wire Cable from Home Power Supply

IMPORTANT: Use the 4-wire cable from home power supply in the U.S. where local

codes do not allow grounding through neutral, New Branch circuit installations

(1996 NEC), mobile homes and recreational vehicles, new construction and in

Canada.

A

E

B

G

H

I

C

D

F

A. Cable from home power

supply

B. Black wires (normally L1)

C. Red wires (normally L2)

D. 4-wire exible conduit from

oven

E. Junction box

F. White wires (normally

N-neutral)

G. UL listed wire connectors

H. green wires (normally

G-ground)

I. UL listed or CSA approved

conduit connector

1. Connect the 2 black wires (B) together

using a UL listed wire connector.

2. Connect the 2 red wires (C) together

using a UL listed wire connector.

3. Untwist white wire from green (or bare)

ground wire coming from the oven.

4. Connect the 2 white wires (F) together

using a UL listed wire connector.

5. Connect the green (or bare) ground

wire (H) from the oven cable to the

green (or bare) ground wire (in the

junction box) using a UL listed wire

connector.

6. Install junction box cover.

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 14 2020-06-24 �� 10:12:37

English 15

Installation instructions

3-Wire Cable from Home Power Supply - U.S. Only

IMPORTANT: Use the 3-wire cable from home power supply where local codes

permit a 3-wire connection.

A

E

B

G

H

I

C

D

F

A. Cable from home power

supply

B. Junction box

C. Black wires (normally L1)

D. White wires (normally

N-neutral)

E. green wires (normally

G-ground)

F. 4-wire exible conduit from

oven

G. Red wires (normally L2)

H. UL listed wire connectors

I. UL listed or CSA approved

conduit connector

1. Connect the 2 black wires (C) together

using a UL listed wire connector.

2. Connect the 2 white wires (D) and

the green (or bare) ground wire (of

the oven cable) using a UL listed wire

connector.

3. Connect the 2 red wires (G) together

using a UL listed wire connector.

4. Install junction box cover.

Install oven

Install

Handle

1. Using 2 or more people, lift the oven

partially into the cabinet cutout. Hang

the install handle onto the side hook of

the oven as shown below.

NOTE

Carefully push against front oven frame.

2. Push against the seal area of the front

frame to push the oven into the cabinet

until the back surface of the front frame

touches the front wall of the cabinet.

3. Push oven completely into the cabinet

and center the oven into the cabinet

cutout.

4. Remove the tape from front trims.

• Securely fasten the oven to the

cabinet using the screws provided.

• Insert the screws through hole in

trim aligning with hole in oven

frame. Do not overtighten screws.

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 15 2020-06-24 �� 10:12:37

16 English

Self-diagnosis

Barrier

WARNING

When inserting the oven, use caution not to

deform or damage the barrier underneath.

Self-diagnosis

Temp sensor & Heater check

1. After connecting the power, check if the display works properly.

2. Remove all accessories (Gliding Rack, Flat-Rack, Smart Divider...etc.) from

inside of the oven cavity.

3. You cannot proceed with self-diagnosis if the oven cavity is hot or the door is

open.

• In this case, “Hot or door” message appears on the display.

4. To start self-diagnosis, press both Hidden Keys simultaneously for 5 seconds

and select install test button.

• Refer to the table below for the hidden keys for each model.

• Self-diagnosis takes approximately 6-7 minutes.

Model DOB30P977DS

Control panel

Hidden Key UPPER + LOWER

Model DOB30P977SS

Control panel

Hidden Key SETTING + RESERVOIR

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 16 2020-06-24 �� 10:12:37

English 17

Self-diagnosis

5. If there is no error, 'PASS' appears on the display with an alert sound.

6. If there is an error, following message appears on the display with an alert

sound.

Model DOB30P977**

Error code Remark

Feature

Upper Broil Upper Broil Fail Double/Single Oven

Upper Bake Upper Bake Fail

Lower Broil Lower Broil Fail Double Oven Only

Lower Bake Lower Bake Fail

7. If an error occurs, contact a Dacor service center for further service.

8. If nish self-diagnosis, press both Hidden Keys simultaneously for 5 seconds

to return to normal standby mode.

NOTE

If you see any other error messages that are not listed above, please contact a

Dacor service center at 833-35-ELITE (833-353-5483).

Memo

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 17 2020-06-24 �� 10:12:37

18 English

Memo

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 18 2020-06-24 �� 10:12:37

IMPORTANT:

Your warranty will not begin until you activate it online or return this form to

Dacor. If you have purchased more than one Dacor product, please return all forms

in one envelope, or activate the warranty for each product online.

Please rest assured that under no conditions will Dacor sell your name or any of the

information on this form for mailing list purposes. We are very grateful that you

have chosen Dacor products for your home and we do not consider the sale of such

information to be a proper way of expressing our gratitude!

Owner’s Name:

Street: Last (Please Print or Type) First Middle

City: State:

Zip:

Purchase Date: Email:

Telephone:

Dealer:

City: State:

Zip:

Your willingness to take a few seconds to ll in the section below will be sincerely

appreciated. Thank you.

1. How were you rst exposed to Dacor products? (Please check one only.)

A. T.V. Cooking Show F. Builder

B. Magazine G. Architect/Designer

C. Appliance Dealer Showroom H. Another Dacor Owner

D. Kitchen Dealer Showroom I. Model Home

E. Home Show J. Other

2. Where did you buy your Dacor appliances?

A. Appliance Dealer D. Builder

B. Kitchen Dealer E. Other

C. Builder Supplier

Please visit www.Dacor.com to activate your warranty online.

WARRANTY INFORMATION

cut herecut here

3. For what purpose was the product purchased?

A. Replacement

only

C. New Home

B. Part of a Remodel D. Other

4. What is your household income?

A. Under $75,000 D. $150,000 – $200,000

B. $75,000 – $100,000 E. $200,000 – $250,000

C. $100,000 – $150,000 F. Over $250,000

5. What are the brands of appliances that you have in your kitchen?

A. Cooktop C. Dishwasher

B. Oven D. Refrigerator

6. Would you buy or recommend another Dacor product?

Yes No

Comments:

Thank you very much for your

assistance. The information you have

provided will be extremely valuable

in helping us plan for the future and

giving you the support you deserve.

Place Serial Number Label Here

Website: www.Dacor.com

Phone: 833-35-ELITE (833-353-5483)

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 19 2020-06-24 �� 10:12:37

Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745

∙ Phone: 833-35-ELITE (833-353-5483) ∙ Fax: (626) 403-3130 ∙ www.dacor.com

DG68-01308A-00

Install_DOB30P977_DG68-01308A-00_EN+MES+CFR.indb 20 2020-06-24 �� 10:12:38

La page charge ...

Dacor DOB30P977SS Guide d'installation

Ce manuel convient également à

Dacor DOB30P977SS Guide d'installation

dans d''autres langues

Autres documents