Immersion Elite Gen 2 French Door End Mullion Lights Guide d'installation

Marque: Immersion

Modèle: Elite Gen 2 French Door End Mullion Lights

Taper: Guide d'installation

Prex:

EL = Elite

FD = French Door

2 = Generation

Light Output Class:

E = Eco Output

S = Standard Output

P = Premium Output

Length in inches:

36 = 36 inches

48 = 48 inches

60 = 60 inches

67 = 67 inches

Color Temperature:

30 = 3000K White

35 = 3500K White

40 = 4000K White

45 = 4500K White

50 = 5000K White

Optic

Conguration:

C = Center

R = Right

L = Left

Packaging:

S = Single

B = Bulk

# = Custom

ELFD2abbccd-e

• Installation to be performed by factory trained service personnel only.

• For use inside a commercial refrigeration case with packaged foods only.

• Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

• Before installing, servicing or cleaning unit, switch power off at the service panel and follow appropriate lock out/tag out safety procedures

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS shown

throughout these instructions.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

End Mullion Lights for French Door Cases

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 1 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

Elite

LED Refrigerated Display Lighting

Installation Guide

DISP104 | GE2029-8802

Parts Needed Per Case

6-Door 5-Door 4-Door 3-Door 2-Door

Center LED Lights 5 4 3 2 1

End LED Light Sets 1 1 1 1 1

Wire Covers 7 6 5 4 3

Using GEPS24D-60U-GLX & GELP24-60U-GL LED Drivers

LED Drivers (36-inch LED Lights) 3 2 1 1 1

LED Drivers (60-inch LED Lights) 4 3 3 2 2

LED Drivers (67-inch LED Lights) 6 5 4 3 2

LED Drivers (48-inch LED Lights) 4 3 3 2 2

Using GEPS6100NCCON-SY, GELP24-100U-GLX & GEPS24D-100U-NA LED Drivers

LED Drivers (36-inch LED Lights) 1 1 1 1 1

LED Drivers (60-inch LED Lights) 3 3 3 2 2

LED Drivers (67-inch LED Lights) 3 3 3 2 2

LED Drivers (48-inch LED Lights) 2 2 2 2 2

Tools Required Components Required

Wire stripper/cutter

Tape measure

Screwdriver

Cordless drill

Hammer

7/64-inch (2.8mm) drill bit

Center punch

LED light

Wire cover

24-volt, Class 2 (UL),

SELV (CE), LED driver

6-32 screws

UL certied 22-14 AWG

(0.33-2.08 mm2) wire

connectors

Prepare Electrical Wiring

LED Driver Rated AC Input Voltage

GEPS6100NCCON-SY 120-240VAC, 60/50Hz

GEPS24D-100U-NA 120-277VAC, 60/50Hz

GELP24-100U-GLX 120-277VAC, 60/50Hz

GEPS24D-60U-GLX 120-277VAC, 60/50Hz

GELP24-60U-GL 120-277VAC, 60/50Hz

• The LED driver must be supplied the rated voltage as listed (LED Driver

Compatibility), and connected to an individual properly grounded

branch circuit, protected by a 15 or 20 ampere circuit breaker or time

delay fuse.

• Wiring must be 2 wire with ground and rated for 75°C (167°F).

• Do not overload driver. Follow loading guidelines on page 6 of this

installation guide.

• Ensure that all connection points are sealed for damp location using the

appropriate method per the NEC or local electrical code.

Electrical Requirements Led Driver Compatibility

This system is compatible with the following LED Drivers.

Please refer to the separate LED driver installation

guide for appropriate wiring connections.

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 2 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

• Refer to manufacturing manual for refrigeration case to identify lighting control circuits. Ensure that power is switched

off at the service panel for the lighting circuit. If a lighting power switch is not provided in the refrigeration case, power

removal can be performed at the main breaker panel.

• Please refer to refrigeration manual for any questions dealing with component locations.

1 - Remove Existing Lighting Components

CAUTION / ATTENTION

Risk of injury. While performing installations described, gloves, safety glasses or goggles should be worn.

Risque de blessure. Lors de l'exécution des installations décrites, des gants, des lunettes de sécurité ou des lunettes de protection doivent être portées.

WARNING / AVERTISSEMENT

Risk of electrical shock. Disconnect power before servicing or installing product. LED Retrot Kit Installation requires knowledge of luminaires electrical

systems. If not qualied, do not attempt installation. Contact a qualied electrician. Install this kit only in the luminaires that have the construction

features and dimensions shown in the photographs and/or drawings.

Risque de choc électrique. Couper le courant avant de réparer ou installer le produit. LED Retrot Kit d’installation nécessite la connaissance des

systèmes luminaires électriques. Si vous n’êtes pas qualié, ne tentez pas l’installation. Contactez un électricien qualié. Installez ce kit seulement dans

les luminaires qui ont les caractéristiques de construction et les dimensions gurant sur les photographies et / ou des dessins.

Turn off power to the

refrigeration case.

Remove all lamp guards and

uorescent tubes from inside

the case.

Locate ballast and remove access cover.

NOTE: Refer to the refrigeration manual for

specic ballast location.

Inside the case, cut wires

as close as possible to

lampholders and remove them.

Disconnect wires to ballast and remove from case.

Leave the existing ballast input and output wires

for reconnection in a later step.

NOTE: Follow all federal and local regulations

when disposing of uorescent tubes, transformers

and ballasts.

Fluorescent

tubes

Lamp

guards

Remove

lampholders

Leave wire

in place

Possible ballast locations:

- Over door frame

- Inside mullion

- Behind raceway

Remove ballast

Leave existing wiring

4 5

2 3

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 3 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

WARNING / AVERTISSEMENT

Risk of re or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrot kit. Check for enclosed

wiring and components.

Risque de feu ou électrocution. Les pièces et câbles électriques risquent d’être endommagés lors du perçage des trous pour l’installation du luminaire

à DEL. Veuillez vérier si des câbles et composantes se trouvent derrière la paroi avant de percer.

To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

Pour éviter l'endommagement de câblage ou l'abrasion, ne pas exposer le câblage aux bords de feuilles de métal ou d'autres objets tranchants.

Mark two hole locations on mullion. Use a 7/64" (2.8 mm) bit to drill mounting holes

through the two marked locations.

NOTE: Refer to the manufacturing manual for

door frame to ensure there are no components

contained inside the mullion that could be drilled

through.

Use center punch and hammer to create a dimple

over the two marked locations.

Total width

of mullion

1-3/32"

(28mm)

Wires to old

ballast

2-1/8"

(54 mm)

minimum

from top of

mullion

WARNING / AVERTISSEMENT

Risk of electrical shock. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not

leave any other open holes in an enclosure of wiring or electric components.

Risque de choc électrique. Seuls les trous ouverts indiqués dans les photos et/ou les dessins peuvent être faites ou modiés à la suite du montage du kit.

Ne pas laisser autres trous ouverts dans l'enceinte du câblage électrique ou composants.

2 - Install Center LED Light(s)

LED Light Length L1

36" 33.4"

48" 46.25"

60" 58.09"

67" 65.19"

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 4 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

Red

stripe (+) Red

stripe (+)

Red (+) Red (+)

White (-) White (-)

Black (-) Black (-)

Proceed to section 4–Electrical Connections to

complete wiring connections.

Refer to wiring diagram on page 7. Connect the

red stripe wire (+) of the LED light to the red wire

(+) of the power supply, and connect the white

wire (-) of the LED light to the black wire (-) of

the power supply using wire connectors or other

connection method suitable for low temperature

usage and stranded cable.

NOTE: If connections are made in an area with

excessive moisture or ice, electrical connections should

be sealed with electrical grade silicone (examples:

Momentive RTV 6700 Series, Momentive White Blanc

RTV 162, Dow Corning 3140, Dow Corning 3145, or

Dow Corning RTV 748).

Secure the top and bottom of the LED light to

the mullion using a #6 x 1/2" (self-threading) or x

3/4" (self-drilling) sheet metal screws. If using the

optional wire cover, install the cover base as well

and a 3/4" (self-threading) or x 1" (self-drilling)

long screw will be required.

OPTIONAL: Additional screws can be used in the

holes along the length of the bar if desired. Refer

to the manufacturer manual for door frame to

ensure there are no components contained inside

the mullion that could be drilled through.

NOTE: Over-sized screws may cause damage to the

LED light.

If using the optional wire cover, tuck wires inside

and snap the cover top over the cover base. Repeat

steps 1–6 for the other side of the case.

Mount the LED driver in the same location

where the ballast was formerly installed.

NOTE: Refer to the "Parts Needed Per Case" table

on page 2 to determine the proper number of

LED drivers to install.

Optional wire cover Optional wire cover

IMPORTANT: Before proceeding, verify correct orientation of lights.

End

Mullion

End

Mullion

Right

Light

Left

Light

Center

Light

Center

Mullion

Glass Door Glass Door

Shelf

Top view of refrigeration case

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 5 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

Length Bar Type

Light Bar

Power (W)

LED Driver:

GELP24-60U-GL

GEPS24D-60U-GL

LED Drivers:

GEPS6100NCCON-SY

GEPS24D-100U-NA

GELP24-100U-GLX

Minimum

Loading QTY

(Min loading > 20W)

Maximum

Loading QTY

(Max loading ~ 54W)

Minimum

Loading QTY

(Min loading > 40W)

Maximum

Loading QTY

(Max loading ~ 90W)

Standard

36” Center 12 2 4 4 7

End 9 3 6 5 10

48” Center 18 2 3 3 5

End 12 2 4 4 7

60” Center 24 1 2 2 3

End 15 2 3 3 6

67” Center 27 1 1 2 3

End 18 2 3 3 5

3 - Electrical Connections

Maximum LED Driver Loading

CAUTION / AATTENTION

Risk of injury. Do not overload LED Driver. Do not exceed limits shown in “Maximum LED Driver Loading” table below.

Risque de blessure. Ne pas surcharger l'alimentation. Ne pas exéder les limites de la table cidessous: “Charges maximales pour les alimentations.”

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 6 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

Electrical Connection Congurations

Multiple LED light’s electrical input should be in parallel connection to an LED driver’s output as shown by the example wiring

diagram. Refer to “Maximum LED Driver Loading” table on page 6 to determine maximum number of LED lights per LED

driver.

One End Set (Right and Left) and One Center LED Light

TERMINAL BLOCK

(AC SOURCE)

LED DRIVER

RIGHT END LED LIGHT

LEFT END LED LIGHT

CENTER LED LIGHT

SWITCH

WHITE (NEUTRAL)

BLACK (LINE)

Occupancy Sensor

RED (+)BLACK

BLACK (-)

WHITE

GRAY

RED STRIPE (+)

PURPLE

WHTIE (-)

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 7 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

Input

AC line

Dimming

OPTIONAL:

Enable dimming

by cutting loop

Output LED

Occupancy

Sensor

GEPS6100NCCON-SY

Connecting a GEPS6100NCCON-SY Driver

Connect DC output

using 4-way

connector.

Connect DC output

using 4-way connector.

Connect AC input using wire nuts. Connect DC output using wire nuts.

Ground

Molex Connector

Purple

Gray

Option Optionor or

• Make input and output connections according to diagrams below.

• Connection methods should be suitable for low temperature usage and standard cable.

• For non-dimming applications, cap the unused wires with 5/32” (4mm) twist on wire connectors.

• For dimming applications, cut the dimming loop on the driver output side and make connections to the occupancy sensor.

• CAUTION: DO NOT apply voltage or power to the switched control circuit – contact closure only.

• Other methods for automated control such as occupancy sensors that switch the AC power side on and off are not recommended and

will void the product warranty.

White (–)

Red stripe (+)

White (–)

Red stripe (+)

Wire Cavity Table

Molex 39-01-4046 (DC)

Cavity 1 - Output DC (+) (Red)

Cavity 2 - Output DC (-) (Black)

Cavity 3 - Dimming (Purple)

Cavity 4 - Dimming (Gray)

Wire Cavity Table

39-01-4030 (AC)

Cavity 1 - Line 1 (Black)

Cavity 2 - Earth Ground (Green)

Cavity 3 - Neutral or Line 2 (White)

AC D

B D

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 8 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

Input

Output

LED

Ground

White (–)

Pink (–)

(–)

Red

stripe (+)

Purple (+)

(+)

Dimming

Controller

Connecting a GELP24-60U-GL or GELP24-100U-GLX Driver

• Make input and output connections according to diagrams below.

• Connection methods should be suitable for low temperature usage and standard cable.

Input

Output

LED

Ground

White (–)

Red stripe (+)

Connecting a GEPS24D-60U-GLX or GEPS24D-100U-NA Driver

• Make input and output connections according to diagrams below.

• Connection methods should be suitable for low temperature usage and standard cable.

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 9 of 10

(Rev 06/21/23)

DISP104-RDL-lmmersion-Elite-End-Mullion-Lights-for-French-Door-Cases-Gen2-Installation-Guide

WARNING/AVERTISSEMENT

Risk of electrical shock. Disconnect power to LED Lights before any cleaning operation.

Risque de choc électrique. Débranchez l'alimentation des éclairages à LED avant toute opération de nettoyage.

It is advised that a periodic inspection be made of the refrigerated display case and LED lights for proper function. If excessive

moisture or ice buildup is noted, this may be a sign that the door seal is damaged and should be replaced. Please note that

prolonged exposure of the LED lights to moisture and ice may result in damage to the LED lights. Any LED lights exhibiting signs of

damage such as discoloration or LEDs that are out should be replaced.

• The outer lens should be cleaned periodically with a mild

liquid dish detergent.

• Do not use chemical cleaners to clean the lens.

• Keep the outside clean. Wipe with a clean cloth lightly

dampened with mild liquid dish detergent. Dry with a

clean, soft cloth.

Cleaning Instructions

Periodic Inspection

• Do not wipe the lens with a soiled dish cloth or wet towel.

These may leave a residue that can damage the nish.

• Do not use scouring pads, powdered cleaners, bleach or

cleaners containing bleach because these products can

scratch and damage the nish.

This product is intended solely for the use of commercial refrigerated, display

or case lighting and is not intended for use in any other application.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

This Class [A] RFLD complies with the Canadian standard ICES-005. /CeDEFR de la classe [A] est conforme à la NMB-005 du Canada.

Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting

point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities

or stockist for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an

environmentally friendly manner and make it available for the recyclable material collection-service.

ImmersionTM Elite Installation Guide

LED.com

and speciﬁcations subject to change without notice. All values are design

or typical values when measured under laboratory conditions.

Page 10 of 10

(Rev 06/21/23)