DeWalt DCGG571B Manuel utilisateur

DCGG571

20V Max* Grease Gun

Pistolet graisseur 20V max*

Pistola engrasadora de 20 V Máx*

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D

e

WALT • www.dewalt.com

Final Paper Size: 8.5 x 5.5"

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury.

NOTICE: Indicates a practice not related to personal

injury which, if not avoided, may result in property

damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

e

WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D

e

WALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

English

1

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

English

2

battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws, or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional Safety Rules for Grease Guns

• Parts of the tool or the hose assembly can break or rupture

due to high pressure. Risk of serious injury may occur.

Before using, always inspect the tool and hose assembly for

damage or wear. Never use if any part of the tool is damaged or

worn.

• Use only D

e

WALT-approved flexible hoses. Hold the hose only

by the flexible hose safety spring guard to avoid personal serious

injury.

• If the hose kinks or is damaged, a rupture may occur which

could cause serious injury. Replace the hose at the first sign of

wear, kink or damage.

• Only use the grease recommended in this manual. Refer to

the Technical Information chart under Using the Grease Gun.

• To reduce the risk of serious personal injury, do not use

the grease gun around or on moving parts, mechanisms or

running equipment.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

WARNING: Risk of injection or severe injury. Rupture of

components can inject grease into skin or eyes, causing

serious injury or infection. Do not treat as a simple cut. Seek

immediate medical attention.

WARNING: Output can be at high pressure. Do not direct

discharge at yourself or others.

WARNING: The grease gun may generate high pressure—up

to 10,000 psi (690 bar). Always wear gloves during operation.

Keep hands clear of the exposed rubber portion of the hose.

WARNING: Risk of fire. Grease may be flammable. Do not

expose to fire or high temperatures. Read and follow all warnings and

instructions from the lubricant manufacturer.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation is

dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

English

3

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other

injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face

and body.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable

surface where it will not cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the battery

pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ...................volts A ...................... amperes

Hz ................. hertz W ..................... watts

min ............... minutes or AC ..........alternating

or DC ... direct current current

................. Class I Construction or AC/DC ... alternating

(grounded) ........................or direct

................. Class II Construction current

(double insulated) no ....................no load

…/min ........... per minute speed

BPM ............. beats per minute n ......................rated

IPM ............... impacts per minute ........................speed

RPM ............. revolutions per .....................earthing

minute terminal

sfpm ............. surface feet ..................... safety alert

..................... per minute symbol

SPM .............strokes per minute ....................visible

..................... .........................radiation

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include the

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below and

then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable liquids,

gases or dust. Inserting or removing the battery pack from the

charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. DO NOT

modify the battery pack in any way to fit into a non-

English

4

compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated D

e

WALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 104°F (40°C)

(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in

the ON position.

WARNING: Fire hazard. Never attempt to open the battery pack

for any reason. If the battery pack case is cracked or damaged, do

not insert into the charger. Do not crush, drop or damage the battery

pack. Do not use a battery pack or charger that has received a sharp

blow, been dropped, run over or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry the battery

pack so that metal objects can contact exposed battery

terminals. For example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails,

screws, keys, etc. Transporting batteries can possibly cause

fires if the battery terminals inadvertently come in contact

with conductive materials such as keys, coins, hand tools

and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in

commerce or on airplanes (e.g., packed in suitcases and carry-on

luggage) UNLESS they are properly protected from short circuits. So

when transporting individual battery packs, make sure that the battery

terminals are protected and well insulated from materials that could

contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC® Seal

The RBRC® (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium-ionbatteries (or battery packs)

indicates that the costs to recycle these batteries (or

battery packs) at the end of their useful life have already

been paid by D

e

WALT. In some areas, it is illegal to

place spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and the Call 2

Recycle® program provides an environmentally conscious alternative.

Call 2 Recycle, Inc., in cooperation with D

e

WALT and other battery

users, has established the program in the United States and Canada

to facilitate the collection of spent nickel cadmium, nickel metal

hydride or lithium-ion batteries. Help protect our environment and

conserve natural resources by returning the spent nickel cadmium,

nickel metal hydride or lithium-ion batteries to an authorized D

e

WALT

English

5

service center or to your local retailer for recycling. You may also

contact your local recycling center for information on where to drop

off the spent battery. RBRC® is a registered trademark of Call 2

Recycle, Inc.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary

markings on the charger, battery pack and product using the

battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside the

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

D

e

WALT rechargeable battery packs. Other types of batteries may

overheat and burst resulting in personal injury and property damage.

NOTICE: Under certain conditions, with the charger plugged into

the power supply, the charger can be shorted by foreign material.

Foreign materials of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum foil or any buildup

of metallic particles should be kept away from the charger cavities.

Always unplug the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before attempting to

clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

e

WALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock or electrocution.

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting

the charger. This will reduce the risk of damage to the electric

plug and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage

or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric

shock.

• An extension cord must have adequate wire size (AWG or

American Wire Gauge) for safety. The smaller the gauge number

of the wire, the greater the capacity of the cable, that is, 16 gauge

has more capacity than 18 gauge. An undersized cord will cause a

drop in line voltage resulting in loss of power and overheating. When

using more than one extension to make up the total length, be sure

each individual extension contains at least the minimum wire size.

The following table shows the correct size to use depending on

cord length and nameplate ampere rating. If in doubt, use the next

heavier gauge. The lower the gauge number, the heavier the cord.

English

6

Minimum Gauge for Cord Sets

Ampere

Rating

Volts Total Length of Cord

in Feet (meters)

120 V 25

(7.6) 50

(15.2) 100

(30.5) 150

(45.7)

240 V 50

(15.2) 100

(30.5) 200

(61.0) 300

(91.4)

More

Than

Not

More

Than AWG

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it to

an authorized service center.

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Chargers

Your tool uses a D

e

WALT charger. Be sure to read all safety

instructions before using your charger. Consult the chart at the end of

this manual for compatibility of chargers and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate outlet before inserting the

battery pack.

2. Insert the battery pack (P) into the charger, as shown in Figure 1,

making sure the pack is fully seated in charger. The red (charging)

light will blink continuously, indicating that the charging process

has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may

be used at this time or left in the charger.

FIG. 1 P

English

7

Indicator Light Operation

DCB101, DCB102, DCB103

PACK CHARGING

PACK CHARGED

x

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

DCB107, DCB112, DCB113, DCB115

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

Charge Indicators

This charger is designed to detect certain problems that can arise.

Problems are indicated by the red light flashing at a fast rate. If this

occurs, re-insert the battery pack into the charger. If the problem

persists, try a different battery pack to determine if the charger is

working properly. If the new pack charges correctly, then the original

pack is defective and should be returned to a service center or other

collection site for recycling. If the new battery pack elicits the same

trouble indication as the original, have the charger and the battery

pack tested at an authorized service center.

HOT/COLD DELAY

DCB101, DCB102, DCB103

These chargers have a hot/cold delay feature. When the charger

detects a battery that is too hot or too cold, it automatically starts

a delay, suspending charging. The red light flashes long, then short

while in the hot/cold delay mode.

Once the battery has reached an optimum temperature, the charger

will automatically resume the charging procedure. This feature

ensures maximum battery life.

DCB107, DCB112, DCB113, DCB115

These chargers have a hot/cold delay feature. When the charger

detects a battery that is too hot or too cold, it automatically starts a

delay, suspending charging. The red light will continue to blink, but a

yellow indicator light will be illuminated during this suspension.

Once the battery has reached an optimum temperature, the yellow

light will turn off and the charger will automatically resume the

charging procedure. This feature ensures maximum battery life.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS

DCB101, DCB102, DCB103

These chargers will not charge a faulty battery pack. The charger

will indicate faulty battery pack by refusing to light or by displaying

problem pack or charger.

NOTE: This could also mean a problem with a charger.

English

8

DCB107, DCB112, DCB113, DCB115

These chargers will not charge a faulty battery pack. The charger will

indicate faulty battery pack by refusing to light.

NOTE: This could also mean a problem with a charger.

Wall Mounting

DCB107, DCB112, DCB113, DCB115

These chargers are designed to be wall mountable or to sit upright on

a table or work surface.

If wall mounting, locate the charger within reach of an electrical

outlet. Mount the charger securely using drywall screws at least

1" (25.4 mm) long, screwed into wood to an optimal depth leaving

approximately 7/32" (5.5 mm) of the screw exposed.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65°F and

75 °F (18° – 24 °C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +104°F (+40°C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to the touch

while charging. This is a normal condition, and does not indicate

a problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

3. A cold battery pack will charge at about half the rate of a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move the charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F – 75 °F

(18° – 24°C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse effect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug the charger before

attempting to clean.

7. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside the

charger. Electric shock may result.

WARNING: Burn hazard. Do not submerge the battery pack in

any liquid or allow any liquid to enter the battery pack. Never attempt

to open the battery pack for any reason. If the plastic housing of the

battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from

direct sunlight and excess heat or cold.

English

9

FIG. 2

F

E D

C

A

B

P

Q

J

H

G

I

M

R

N

O

U

V

T

K

L

R

S

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

COMPONENTS (Fig. 2, 5)

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

FIGURE 2

A. Variable speed trigger switch O. Retaining slot

B. Lock-off button P. Battery

C. Handle Q. Battery release button

D. LED worklight R. Rubber feet

E. LED worklight button S. Hose clip

F. Top cap T. Shoulder strap mount

G. Flexible hose U. Shoulder strap clip holes

H. Flexible hose safety spring guard V. Filter

I. Flexible hose coupler FIGURE 5

J. Grease tube W. Pressure relief valve

K. Grease tube cap X Purge valve

L. Grease tube handle Y. Check valve

M. Grease tube rod Z. 1/8" NPT fill port

N. Grease tube assembly AA. 1/8" NPT fill port plug

English

10

Variable Speed Trigger Switch (Fig. 2, 4)

LOCK-OFF BUTTON AND TRIGGER SWITCH

Your grease gun is equipped with a lock-off button (B).

To lock the trigger switch, press the lock-off button as shown in

Figure4. Always lock the trigger switch (A) when carrying or storing

the tool to eliminate unintentional starting. The lock-off button is

colored red to indicate when the switch is in its unlocked position.

To unlock the trigger switch, press the

B

FIG. 4

lock-off button as shown in Figure 4.

Squeeze the trigger switch to turn the

motor ON. Releasing the trigger switch

turns the motor OFF.

NOTE: The variable speed trigger switch

will give you added versatility. The further

the trigger is depressed the higher the

output of grease.

WARNING: This tool has no provision to lock the switch in the ON

position, and should never be locked ON by any other means.

Pressure Relief Valve (Fig. 5)

The pressure relief valve (W) is set at FIG. 5

X

W

AA

Y

Z

the factory to relieve pressure

above 10,000 psi (690 bar).

Grease coming out of the pressure

relief valve indicates a clog in the

fitting, line or bearing. Any of these

conditions must be corrected

before proceeding.

INTENDED USE

This grease gun is designed for professionally dispensing lubricant.

DO NOT use under wet conditions or in presence of volatile

flammable liquids or gases.

This grease gun is a professional power tool. DO NOT let children

come into contact with the tool. Supervision is required when

inexperienced operators use this tool.

LED Worklight (Fig. 2, 3)

CAUTION: Do not stare into worklight. Serious eye injury could

result.

There is a LED worklight (D) located on the top cap (F). The worklight

is activated when the trigger switch is depressed and when the LED

worklight button (E) is in the ON position. When the LED worklight

button is in the OFF position, the LED worklight will not turn on when

the trigger is depressed. The worklight will automatically turn off 20

seconds after the trigger switch is released. If the trigger switch

remains depressed, the worklight will remain on.

NOTE: The worklight is for lighting the immediate work surface and

is not intended to be used as a flashlight.

FIG. 3 E D

F

English

11

WARNING: The grease gun may generate high pressure. Do

not remove or tamper with the pressure relief valve. Serious injury

may occur.

Shoulder Strap (Fig. 2)

Your grease gun comes with a shoulder strap. Hook the shoulder

strap clips into the shoulder strap clip holes (U) found on the shoulder

strap mount (T).

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn

tool off, push the lock-off button to the OFF position, and

remove the battery pack before making any adjustments or

removing/installing attachments or accessories. An accidental

start-up can cause injury.

Installing a Grease Cartridge (Fig. 2, 5, 6)

1. Pull the grease tube handle (L)

O

FIG. 6

M

L

out as far as it will go, then

secure the grease tube rod (M)

into the retaining slot (O) by

moving the rod to the side.

Ensure the rod is placed

securely in the slot to prevent it

from disengaging.

2. Unscrew the grease tube

assembly (N) from the grease

gun.

3. Remove the plastic cap from

the grease cartridge, then insert the cartridge, open end first, into

the grease tube (J).

4. Remove the seal from the other end of the grease cartridge.

5. Thread the grease tube assembly (N) back into the grease gun

and screw it in securely.

6. Release the grease tube rod (M) from the retaining slot (O) and

slowly press it back into the tube.

7. Use the purge valve (X, Fig. 5) to bleed off any air that may be

trapped in the cartridge. Refer to Purging Air Pockets.

IMPORTANT: The grease gun will lose its prime if there are air

pockets in the lubricant.

Removing Empty Grease Cartridge

(Fig.2)

1. Pull the grease tube handle (L) out as far as it will go, then secure

the grease tube rod (M) into the retaining slot (O) by moving the

rod to the side. Ensure the rod is placed securely in the slot to

prevent it from disengaging.

2. Unscrew the grease tube assembly (N) from the grease gun and

remove.

3. Gently release the grease tube handle (L) to expel the empty

cartridge from the grease tube.

Filling the Grease Gun from a Bulk

Container (Fig. 2, 5–9)

PREPARING THE GREASE GUN FOR SUCTION AND FILLER

PUMP FILLING

(FIG. 1, 7)

NOTE: Be sure the grease gun is empty of grease before beginning

this process.

1. Unscrew the grease tube (J) from the grease gun assembly (N).

2. Unscrew the grease tube cap (K) from the grease tube (J) and pull

out the grease rod (M).

English

12

3. Using your thumb and FIG. 7

Rubber Seal Position

for Grease for Filling from

Cartridge Bulk Container

GG

forefinger, flip the rubber

seal (GG) from the rear to

the front. Refer to Figure7.

NOTE: The seal resembles

a cup, which should open

toward the top cap (F, Fig. 2)

when prepared for suction and

filler pump filling.

4. Reinsert the grease tube

rod (M) back into the

grease tube (J).

SUCTION FILLING FROM A

BULK CONTAINER (FIG. 2,

5, 6, 8)

1. Put the open end of the

grease tube assembly into

the bulk lubricant.

2. Slowly pull back the grease tube handle (L) to FIG. 8

suction the lubricant into the grease gun.

NOTE: Be sure to keep the open end of the grease

tube assembly far enough into the lubricant to

prevent air pockets in the grease tube.

3. When the grease tube rod (M) is fully extended,

secure it into the retaining slot (O)

4. Remove the grease gun tube assembly from

the bulk lubricant and wipe off excess grease.

5. Screw the grease gun tube assembly (N) back

into the grease gun.

6. Release the grease tube rod (M) from the

retaining slot (O) and slowly press it back into

the tube.

7. Use the purge valve (X, Fig. 5) to bleed off any air that may be

trapped in the cartridge. Refer to Purging Air Pockets.

FILLER PUMP FILLING FROM A BULK CONTAINER

(FIG. 5, 6, 9)

This tool comes with a 1/8" NPT fill port FIG. 9

(Z, Fig. 5) for attaching a low pressure fill

coupler onto the unit.

WARNING: Never thread a high-

pressure coupler onto the grease

gun’s 1/8" NPT fill port. Serious injury

may occur due to excessive pressure.

Use low-pressure couplers only.

CAUTION: The fill pump loader must

connect correctly with the grease gun’s

1/8" NPT port. The filler pump may

not operate if the components are not

compatible.

Installing the low pressure coupler

(not supplied with the tool)

1. Thread the grease tube assembly (N)

back into the grease gun and screw it

in securely.

2. Pull the grease tube handle (L) out

as far as it will go, then secure the

grease tube rod (M) into the retaining

slot (O) by moving the rod to the side.

Ensure the rod is placed securely in

the slot to prevent it from disengaging.

3. Remove the 1/8" NPT fill port plug

(AA) from the fill port.

4. Thread the appropriate low pressure

coupler onto the 1/8" NPT fill port (Z).

English

13

5. Release the grease tube rod (M) from the retaining slot (O) and

slowly press it back into the tube.

6. Use the purge valve (X) to bleed off any air that may be trapped

in the cartridge. Refer to Purging Air Pockets.

FILLING THE TOOL FROM THE LOW PRESSURE FILLER

PUMP (FIG. 2, 5, CON9)

1. Pull back on the grease tube handle slowly and rotate the rod until

it is secure in place.

NOTE: Do not lock the rod into the retaining slot (O).

2. Connect the low pressure fitting on the grease gun to the

appropriate low pressure fitting on the filler pump. These fittings

DO NOT lock together. This prevents the grease gun cartridge

from being over filled.

3. Fill until the rod is pushed out of the grease tube approximately

8" (20cm). Do not overfill. If the rod fails to move during the filling

process, stop. This indicates that the rod is not connected to the

plunger and step one must be repeated before proceeding.

4. Rotate rod to release and carefully push rod back into the grease

tube.

5. Use the purge valve (X) to bleed off any air that may be trapped

in the cartridge. Refer to Purging Air Pockets.

Purging Air Pockets (Fig. 2, 5)

IMPORTANT: Air pockets in the grease can cause the grease gun to

lose prime. Eliminate air pockets after each refill or if the grease gun

fails to pump grease:

1. Unscrew the purge valve (X) without removing it, until all air has

escaped.

2. Tighten the purge valve (X).

3. Uncap the flexible hose (G) then depress the variable speed

trigger switch (A) for 10–20 seconds.

4. If grease fails to flow through the hose, repeat from step 1.

NOTE: This tool has been tested at the factory, which may result in

a small amount of grease left in the grease tube and hose assembly.

It is recommended to purge the tool with the brand of grease to be

used before first use.

OPERATION

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making any

adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

Installing and Removing the Battery Pack

(Fig. 10)

NOTE: For best results, make sure your battery pack is fully charged.

To install the battery pack (P) into the tool handle, align the battery

pack with the rails inside the tool’s handle and slide it into the handle

until the battery pack is firmly seated in the tool and ensure that it

does not disengage.

To remove the battery pack from the tool, press the release button (Q)

and firmly pull the battery pack out of the tool handle. Insert it into the

charger as described in the charger section of this manual.

P

Q

FIG. 10

FUEL GAUGE BATTERY PACKS (FIG. 11)

Some D

e

WALT battery packs include a fuel gauge which consists of

three green LED lights that indicate the level of charge remaining in

the battery pack.

English

14

The fuel gauge is an indication of approximate levels of charge

remaining in the battery pack according to the following indicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold

FF

FIG. 11

the fuel gauge button (FF). A combination

of the three green LED lights will illuminate

designating the level of charge left. When

the level of charge in the battery is below

the usable limit, the fuel gauge will not

illuminate and the battery will need to be

recharged.

NOTE: The fuel gauge is only an indication

of the charge left on the battery pack. It

does not indicate tool functionality and is subject to variation based

on product components, temperature and end-user application.

For more information regarding fuel gauge battery packs, please call

1-800-4-D

e

WALT (1-800-433-9258) or visit our website www.dewalt.

com.

Using the Grease Gun (Fig. 2)

WARNING: To reduce the risk of serious personal injury,

always maintain a grip on the handle (C) when operating the

grease gun or positioning the hose onto fittings.

To operate the grease gun, hold the grease gun by the handle (C), or

place it on a stable surface upright on its rubber feet (R) maintaining

a grip on the handle. Holding the hose by the flexible hose safety

spring guard (H), connect the flexible hose grease coupler (I) or

other appropriate grease coupler, onto the grease fitting to be filled.

Carefully depress the variable speed trigger switch to begin the filling

process. Once the correct amount of grease has been dispensed,

release the trigger and remove the coupler from the grease fitting. If

the coupler does not release, there may still be residual pressure in

the line. Moving the coupler from side to side can relieve the residual

pressure so it can be removed from the coupling. If the coupler leaks

excessively or does not hold on to the grease fitting, it should be

replaced.

TECHNICAL INFORMATION

Grease type Up to NLGI #2

Voltage 20 V

Pressure 10,000 psi (690 bar)

Volume/Flow rate 5 fl. oz./min (147.87 ml/min)

Grease capacity 16 oz Bulk (453 g)

14.5 oz Cartridge (411 g)

Tool weight without battery 8 lbs (3.63 kg)

Hose length 42" (107 cm)

MAINTENANCE

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making any

adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

English

15

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

BATTERY CLEANING INSTRUCTIONS

Dirt and grease may be removed from the exterior of the battery using

a cloth or soft non-metallic brush. Do not use water or any cleaning

solutions.

WARNING: Never use solvents or other harsh chemicals for

cleaning the battery. These chemicals may weaken the plastic parts.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do not

use water or any cleaning solutions.

WARNING: Never use solvents or other harsh chemicals for

cleaning the charger. These chemicals may weaken the plastic parts.

CLEANING CONTAMINANTS FROM THE GREASE GUN

Cleaning Contamination from the Check Valve (Fig.12)

Should the grease gun fail to FIG. 12

CC

DD

EE

BB

Y

dispense grease, the check valve

(Y) should be cleaned.

1. Remove the check valve

plug (BB), then the disc (EE),

spring (DD) and check valve

ball (CC).

2. Clean the ball (CC) and the

check valve area in the main

casting.

3. Reinstall the ball (CC), the spring (DD), and then the disc (EE).

4. After all grease is cleaned from the area, reinstall the check valve

plug (BB).

Cleaning Contamination from the Filter (Fig. 2, 13)

Should the grease gun fail to dispense FIG. 13

V

grease, clean the filter (V).

NOTE: If there is still grease in the tube,

open the purge valve prior to pulling the

tube handle.

1. Pull the grease tube handle (L) out

as far as it will go, then secure

the grease tube rod (M) into the

retaining slot (O) by moving the rod

to the side. Ensure the rod is placed

securely in the slot to prevent it from

disengaging.

2. Unscrew the grease tube assembly (N) from the grease gun and

remove.

3. Using a small flat-blade screwdriver or pick, carefully pop out the

filter.

English

16

4. Wipe off the filter using a soft cloth. If the filter still has debris in it

after wiping, a soft brush or swab may be used.

5. Once clean, reinsert the filter into the round groove, ensuring it is

fully seated, and reattach the grease tube assembly to the grease

gun.

Accessories

WARNING: Since accessories, other than those offered by

D

e

WALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only D

e

WALT recommended accessories should be used with

this product.

WARNING: Extreme pressure may cause nozzle extension or

flexible hose to burst. Use only D

e

WALT approved hoses and follow

flexible hose instructions and warnings.

Recommended accessories for use with your tool are available at

extra cost from your local dealer or authorized service center. If you

need assistance in locating any accessory, please contact D

e

WALT

Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call

1-800-4-D

e

WALT (1-800-433-9258) or visit our website: www.dewalt.

com.

ACCESSORIES

DCGG5701 1/8" NPT Grease Gun Coupler

DCGG5701-3 1/8" NPT Grease Gun Coupler 3-pak

DCGG5702 Right Angle Grease Gun Coupler

DCGG5703-42 1/8" NPT Grease Gun Hose Assembly (42") (107 mm)

DCGG5703-24 1/8" NPT Grease Gun Hose Assembly (24") (61 mm)

DCGG5704 Clear Grease Gun Cartridge Tube

Repairs

The charger and battery pack are not serviceable.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment (including brush inspection and replacement) should

be performed by a D

e

WALT factory service center, a D

e

WALT

authorized service center or other qualified service personnel. Always

use identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

D

e

WALT will repair, without charge, any defects due to faulty materials

or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair

information, visit www.dewalt.com or call 1-800-4-D

e

WALT (1-800-

433-9258). This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights

which vary in certain states or provinces.

English

17

In addition to the warranty, D

e

WALT tools are covered by our:

1 YEAR FREE SERVICE

D

e

WALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON D

e

WALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180,

DCB120, DCB127, DCB201, DCB203, DCB203BT, DCB207

3 YEARS FREE SERVICE ON D

e

WALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205205

D

e

WALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any

way. D

e

WALT is not responsible for any injury caused by tampering

and may prosecute warranty fraud to the fullest extent permitted by

law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

D

e

WALT Power Tool, Laser, or Nailer for any reason, you can return

it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the

local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

e

WALT (1-800-433-

9258) for a free replacement.

English

18

La page charge ...

DeWalt DCGG571B Manuel utilisateur

Ce manuel convient également à

DeWalt DCGG571B Manuel utilisateur

dans d''autres langues

Autres documents