VTech VM3258 Mode d'emploi

Catégorie
Babyphones
Taper
Mode d'emploi
Specifications are subject to change without notice.
© 2022 VTech Communications, Inc. All rights reserved.
04/22. VM3258-X_QSG_V2.
VM3258
VM3258-2
2.8” Video Monitor
with Night Light
Go to www.vtechphones.com
to register your product for enhanced
warranty support and the latest VTech
product news.
1 Connect the baby monitor
2
Power on or off the baby monitor
What’s in the box
4
Status check
Once you power on both
your baby unit and parent
unit, your parent unit
displays image from the
baby unit, and the LINK
LED light turns on.
3 Positioning the baby monitor
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Quick start guide
Talk to your baby unit
Press and hold TALK and speak to your
parent unit. Your voice is transmitted to
the baby unit. Release TALK when done
talking and hear your baby again.
Basic operation - Parent unit
Overview - Parent unit
7HFKQLFDOVSHFLơFDWLRQV
Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The applied nameplate is located at the bot tom of the
baby unit’s base.
When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height
above 2 meters.
4. This product is not a substitute for adult supervision of the
infant. Supervising the infant is the parent’s or caregiver’s
responsibility. This product could cease operating, and
therefore you should not assume it will continue working
properly for any given period of time. Further, this is not
a medical device and should not be used as such. This
product is intended to assist you in supervising your baby.
5. Do not use this product near water. For example, do
not use it next to a bath tub, wash bowl, kitchen sink,
laundry tub or swimming pool, or in a wet basement
or shower.
6. CAUTION: Use only the battery provided. There may be a
risk of explosion if a wrong type of battery is used for the
parent unit. The battery cannot be subjected to high or low
extreme temperature and low air pressure at high altitude
during use, storage or transportation. Disposal of battery
into fire or a hot oven, or mechanically crushing or cutting or
the battery can result in an explosion. Leaving the battery in
an extremely high temperature surrounding environment
can result in an explosion or the leakage of flammable liquid
of gas. Battery subjected to extremely low air pressure may
result in an explosion or the leakage of flammable liquid or
gas. Dispose of used battery according to the information in
The RBRC seal.
7. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Power adapter information:
Parent unit output: 5V DC 1 A
VTech Telecommunications Ltd.
Model: VT05EUS05100
Baby unit output: 5V DC 600mA.
VTech Telecommunications Ltd.
Model: VT05EUS05060
Rechargeable battery information:
Zhuhai Great Power Energy Co., Ltd.
Li-ion battery, 3.6V, 2600mAh, 9.36Wh;
Model: ICR18650-2.6Ah-3.6V-1S1P
8. The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if it
is plugged into a ceiling, under-the-table or cabinet
outlet.
9. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
10. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth
for cleaning.
11. Do not cut off the power adapters to replace them with
other plugs, as this causes a hazardous situation.
12. Do not allow anything to rest on the power cords. Do
not install this product where the cords may be walked
on or crimped.
13. This product should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supply in your home,
consult your dealer or local power company.
14. Do not overload wall outlets or use an extension cord.
15. Do not place this product on an unstable table, shelf,
stand or other unstable surfaces.
16. This product should not be placed in any area where
proper ventilation is not provided. Slots and openings
in the back or bottom of this product are provided for
ventilation. To protect them from overheating, these
openings must not be blocked by placing the product
on a soft surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or heat
register.
17. Never push objects of any kind into this product
through the slots because they may touch dangerous
voltage points or create a short circuit. Never spill liquid
of any kind on the product.
18. To reduce the risk of electric shock, do not
disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the
product other than specified access doors may
expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock
when the product is subsequently used.
19. You should test the sound reception every time you
turn on the units or move one of the components.
20. Periodically examine all components for damage.
21. There is a very low risk of privacy loss when using
certain electronic devices, such as baby monitors,
cordless telephones, etc. To protect your privacy,
make sure the product has never been used before
purchase, reset the baby monitor periodically by
powering off and then powering on the units, and
power off the baby monitor if you will not use it for
some time.
22. Children should be supervised to ensure that they do
not play with the product.
23. The product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between
32
o
F and 104
o
F.
2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to a
heating source.
3. Batteries should not be exposed to excessive heat such
as bright sunshine or fire.
4. Warning—Strangulation Hazard—
Children have STRANGLED in cords.
Keep this cord out of the reach of
children (more than 3 ft (0.9m) away). Do
not remove this tag.
5. Never place the baby unit(s) inside the baby’s crib or
playpen. Never cover the baby unit(s) or parent unit
with anything such as a towel or a blanket.
6. Other electronic products may cause interference
with your baby monitor. Try installing your baby
monitor as far away from these electronic devices
as possible: wireless routers, radios, cellular
telephones, intercoms, room monitors, televisions,
personal computers, kitchen appliances and
cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless
devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and
implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR recommends to physicians
that:
Pacemaker patients
Should keep wireless devices at least six inches from the
pacemaker.
Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned
ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and
according to the instructions in this user’s manual, the
product is safe to be used based on scientific evidence
available today.
Important safety instructions
1 set for VM3258
2 sets for VM3258-2
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels 32
LCD 2.8” Color LCD
(QVGA 320x240 pixel)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Power requirements Parent unit: 3.6V, 2600mAh Li-ion, 9.36Wh Li-ion battery
Baby unit power adapter: Output: 5V DC @ 600mA
Parent unit power adapter: Output: 5V DC @ 1A
Connect the baby unit to a power
supply to turn it on. Disconnect the
baby unit to turn it off.
Press and hold POWER to power on or off
your parent unit.
Caution
The default volume of your parent unit
is level 3, and the maximum volume is
level 5. If you experience high-pitched
screeching noise from your baby
monitor while positioning:
- Make sure your baby unit and parent unit
are more than 3 feet (1 meter) apart, OR
- Turn down the volume of your parent unit.
NONO
Note
To avoid interference from other electronic
devices, place your baby monitor at least 3 feet (1
meter) away from devices such as wireless routers,
microwaves, cell phones and computers.
The baby unit’s POWER LED
light turns on.
Press and hold
Turn off the screen
Press POWER/LCD OFF to switch off the
screen. You can still hear sound from the
selected baby unit.
Tip
Press any key on the parent unit to turn on
the screen again.
Use the menu
Press MENU to enter the menu, or save a setting. You can use the parent unit for advanced
settings or operations, such as to play or stop the baby unit’s lullaby, or to adjust the baby
unit’s sound sensitivity.
While in the menu:
• Press or to scroll among
the menu options.
• Press or to select an item.
• Press SELECT to confirm your
selection.
• Press TALK/EXIT to exit the
menu and return to live view.
Quick start guide VM3258 VM3258-2
For more support information
S
m
NOTESNOTE
The rechargeable battery in the parent unit is built-in.
Use only the power adapters supplied with this product.
Make sure the baby monitor is not connected to a switch-controlled electric outlet.
Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of a baby monitor, so do not connect them to any ceiling, under-the-
table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.
10
11
12
1
2
4
5
6
8
9
7
3
Parent unit icons
Main
menu Sub-menu
Volume
Volume
• Adjust the parent unit’s
speaker volume.
Settings
Screen off timer
The parent unit display will
dim to conserve energy after
your chosen amount of time
of inactivity.
Brightness
• Adjust the parent unit’s LCD
screen brightness level.
Zoom
• Zoom in and out of the video
displayed from the baby unit.
Temperature
• Turn on/off temperature alert
tone.
• Set the parent unit to beep
whenever the room temperature
detected by the baby unit falls
outside of the set temperature
range.
• Set the minimum/maximum
temperature.
• Set temperature display in
Fahrenheit (oF) or Celsius (oC).
< 3ft (1m)
3ft (1m)
Caution
Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the
baby’s crib or playpen.
For operations and guides to help you using your video monitor, and for
latest information and supports, go and check the online help topics and
online FAQs.
Use your smartphone or mobile device to access our online
help.
Go to https://help.vtechphones.com/VM3258 or
https://help.vtechphones.com/VM3258-2; OR
Scan the QR code on the right. Launch the camera app or
QR code scanner app on your smartphone or tablet. Hold
the device’s camera up to the QR code and frame it. Tap the
notification to trigger the redirection of the online help.
- If the QR code is not clearly displayed, adjust your
camera’s focus by moving your device closer or further
away until it is clear.
You can also call our Customer Support at 1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada] for help.
Overview - Baby unit
Need help?
S
m
VM3258
VM3258-2
1
2
5
4
6
3
11
Main
menu Sub-menu
Sound Detection
VOX (Voice Activated Alert)
Sensitivity
You can choose to hear
sounds from the baby unit
all the time, or to only hear
sounds that exceed a certain
level. Adjust the microphone
sensitivity of your baby unit,
the higher the sensitivity
level, the more sensitive
the baby unit is in detecting
sounds to be transmitted
to the parent unit. See
Sound sensitivity and sound
activation section.
Sound-activated screen
• When it is on, and the baby
unit detects no sound, the
parent unit screen stays off
to save power. Once a sound
is detected, the parent unit
screen and speaker turns on
automatically, and you can
see and hear your baby. The
parent unit will then turn off
again after 50 seconds of no
sound detection.
NONO
Note
• When the parent unit screen
is off and it receives alerts, for
example, link lost between
parent unit and baby unit, or
battery is low, the parent unit
screen and speaker will
turn on.
Main menu icons
Adjust parent unit speaker volume
Press VOL+ / VOL- to adjust your
parent unit speaker volume.
Zoom
1. Press MENU when in idle mode.
2. Choose .
3. Press or to choose (Zoom in) or
(Zoom out), then press SELECT to
confirm your selection.
Status icons
Connection status
or displays when strong signal strength is detected between the
baby unit and the parent unit.
or displays when moderate or low signal strength is detected
between the baby unit and the parent unit.
Patrol mode
• Displays when the parent unit is in PATROL mode (For VM3258-2 only).
or Current view status
• Displays the baby unit number of the baby unit that is being viewed.
Zoom
• Displays when the current image on the parent unit has zoomed in.
Night vision
• Displays when the baby unit being viewed has activated the night vision
feature.
Talkback
• Displays when talking back to the baby units from parent unit.
Lullaby
• Displays when a lullaby is playing.
Night light
• Displays when the baby unit’s night light is turned on.
Mute alert
• Displays when the parent unit speaker volume is set to zero.
• Displays when the parent unit is talking to the baby unit.
or
Real-time temperature
• Displays the real-time temperature detected by the baby unit in
Fahrenheit (oF) or Celsius (oC) (e.g. 57
oF or 14
oC).
Battery status
animates when the battery is charging.
displays solid when the battery is fully charged.
displays when the battery is low and needs charging.
Press and hold
1Light Sensor
2Camera lens
3Infrared LEDs
4POWER LED light
5Night light
6Microphone
7Power jack
8Speaker
9PAIR hole
The parent unit and
baby unit(s) provided
are already paired.
1 Connect the baby monitor (cont’d)
Charge the parent unit battery
When you have connected and turned on the parent unit, the battery will be charged
automatically.
Notes
Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When
the parent unit battery is fully charged, the battery icon becomes solid .
It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,
turn the parent unit off while charging.
The standby time varies depending on the sensitivity level you set, your actual use and the age of
the battery.
The battery icon indicates the battery status (see the following table).
Battery indicators Battery status Action
The screen displays .
The light flashes.
The battery has very little
charge and may be used for
only a short time.
Charge
without interruption
(about
30 minutes).
The battery icon becomes
solid .
The battery is fully charged. To keep the battery charged, connect
it to AC power when not in use.
UL STD.
62368-1
CERTIFIED TO
CSA STD.
C22.2 NO.62368-1
CONFORMS TO
7
8
10
9
1Antenna
2Battery LED light
33-level sound indicator light
4 Arrow keys
VOL+ / VOL-
5MENU/SELECT
6LINK LED light
On when the parent unit is linked to the
baby unit.
Flashes when the link to the baby unit is lost.
7TALK/EXIT
Press and hold to talk to the baby unit.
While in a submenu, press to exit.
8POWER/LCD OFF
9Microphone
10 Power jack
11 RESET
Force reboot the parent unit.
12 Speaker
Submenu
Main menu
10 Night light ON/OFF
11 Slots for wall mounting
Night vision
Mount the baby unit on dry wall (optional)
For VM3258-2 only
Sound sensitivity and sound activation
The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in
an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of
service within the United States and Canada.
The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal
waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or
at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and
disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor
is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge
the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby
units, the CEC battery charging testing mode is activated while it is powered off and charging.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with
the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of
approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your
face.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference, including interference that may cause undesired operation of the
device.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were
met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should
be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect
to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
The RBRC seal
California Energy Commission battery
charging testing mode
FCC and IC regulations
Dim mode
Parent unit icons (cont’d)
The baby unit has infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
It is normal to see a short white glare on
your parent unit screen as the baby unit is
adapting to the dark environment.
When the infrared LEDs are on, the
images are in black and white. This is
normal.
Tip
Depending on the surroundings and
other interfering factors, like lighting,
objects, colors and backgrounds, the
display resolution may vary. Adjust the
baby unit’s angle or place the baby unit at
a higher elevation to prevent glare and a
blurry display.
The dim mode helps you save parent unit power. Your parent unit display will dim
automatically after 10 minutes of inactivity, in which there is neither key pressed nor alert
received from the baby unit.
10 min inactivity
Press any button
Note
When the screen is dimmed, any keypress or alert message will trigger the screen to return to the
preset brightness level. After 10 minutes of inactivity, it will resume to dim mode.
Sound activated screen
When sound activation is on, the parent unit screen stays off to save power when the baby unit
detects no sound. Once the baby unit detects sounds that are louder than the chosen sound
sensitivity level, the parent unit screen turns on automatically. It will then turn off again after 50
seconds of no sound detection.
1. Press MENU when the parent unit is idle.
2. Press or to choose .
3. Press or to choose , then press SELECT to confirm your selection.
If you are viewing baby unit , the POWER LED light of baby unit turns on.
As baby unit is not being viewed, its POWER LED light flashes.
Note
If you power on only one baby unit, your parent unit may display and the LINK LED light will flash.
Status check - Two baby units
Change different views - Patrol
10s
1. Press MENU when the parent unit is idle.
2. Press or to choose .
3. Press or to choose between and , then press SELECT to confirm the baby unit
you would like to view.
Change different views - Single-cam
Use a pencil to mark two holes in parallel.
Make sure they are the same distance apart
as the wall mount holes on the baby unit.
Note
Check for reception strength and camera
angle before drilling the holes.
Not Included
You will need to purchase the following
items separately to mount your baby unit:
2 screws 2 anchors
Adjust the camera angle.
Drill two holes in the wall ( 7/32 inch drill bit ).
If you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than
a stud, insert the wall anchors into the holes.
Tap gently on the ends with a hammer until
the wall anchors are flush with the wall.
Insert the screws into the holes and
tighten the screws until only 1/4 inch
of the screws are exposed.
Align the wall mount holes on the
baby unit with the screws on the wall.
Slide the baby unit down until it locks
into place.
Note
The types of screws and anchors you need
depend on the composition of the wall.
Below are the questions most frequently asked about the baby monitor.
Why is the
baby monitor
not responding
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby units and the parent unit.
2. Wait a few seconds before connecting power back to the baby units and the parent unit.
3. Turn on the baby units and the parent unit.
4. Wait for the parent unit to synchronize with the baby units. Allow up to one minute
for this to take place.
Why doesn’t the
power-on light of the
baby unit and parent
unit go on when I switch
on the units?
Perhaps the parent unit is not connected to the power. Insert the appliance plug into
the parent unit and put the adapter in a wall socket. Then, press and hold POWER to
switch on the parent unit and to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug into
the baby unit and put the adapter in a wall socket. The baby unit will switch on and
establish a connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by a wall switch.
You may have used the battery for a long time. See Warranty for repair/replacement.
Why is my screen in
black and white?
The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
a blurry display on my
screen when viewing at
night?
During night-time or in a dark room, the surroundings and other interfering factors,
like lighting, objects, colors and backgrounds may affect the image quality on your
parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher
elevation to prevent glare and a blurry display.
Why does the baby
monitor produce a
high-pitched noise?
The parent unit and baby units may be too close to each other.
Move the parent unit away from the baby units until the noise stops; OR
Turn down the volume of your parent unit.
Why does the parent
unit beep?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet).
The parent unit may not have enough power for the parent unit to perform normally.
Charge the battery in the parent unit until the battery icon becomes solid .
The temperature of your baby’s room may be too high or too low.
Why does the parent
unit react too quickly to
other sounds?
The baby unit also picks up other sounds than those of your baby. Adjust the VOX
sensitivity level to a lower level or decrease the parent unit speaker volume.
Why can’t I hear sounds/
my baby cry?
The parent unit speaker volume may be too low. See Adjust parent unit speaker
volume to increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the
baby unit to set to a higher level.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet).
Other electronic products and wireless products may cause interference with your
baby monitor. Try installing your baby monitor as far away from these devices as
possible.
If you power on only one baby unit, your parent unit may display , and the LINK
LED light will flash.
Frequently asked questions Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the
use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or
claims by third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Warning icons and messages
Battery low at
Parent Unit
The battery is empty and
needs to be recharged.
Operation is in progress.
Temperature
too high
The temperature
detected by the baby unit
is higher than the desired
temperature alert range.
Temperature
too low
The temperature
detected by the baby unit
is lower than the desired
temperature alert range.
No Link to
Camera
The parent unit is
searching for baby units
or the link between the
baby unit and the parent
unit is lost.
The parent unit is
connected to AC power.
LINK • On when the parent unit is
linked to the baby unit.
• Flashes when the link to the
baby unit being viewed is
lost.
• On when the parent unit is
connected to AC power, or
the battery is charging.
• Flashes when the parent
unit battery is low and
needs charging.
• Off when the parent unit
is disconnected from AC
power.
Parent Unit Indication Lights
Mesures de sécurité importantes
La plaque signalétique appliquée est située au bas du socle
de l’unité du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les
risques d’incendie, d’électrocution et de blessures corporelles,
dont ceux qui suivent :
1. Observez toutes les instructions et mises en garde inscrites
sur l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une
hauteur supérieure à 2 mètres.
4. Ce produit ne remplace pas la surveillance adulte du
nourrisson. La supervision du nourrisson est la responsabilité
du parent ou de la personne qui s’occupe de l’enfant. Ce
produit pourrait cesser de fonctionner et, par conséquent,
vous ne devriez pas présumer qu’il continuera de fonctionner
correctement pendant une période de temps donnée. De
plus, il ne s’agit pas d’un instrument médical et ne devrait pas
être utilisé comme tel. Ce produit est destiné à vous aider à
superviser votre bébé.
5. N’utilisez pas cet appareil près de l’eau ni de toute autre
source d’humidité, par exemple, près d’une baignoire,
cuve à lessive, évier de cuisine, dans un sous-sol humide
ni près d’une piscine, dans un soussol humide ou une
douche.
6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il
existe un risque d’explosion si un autre type de batterie est
utilisé pour l’unité Parents. N’incinérez pas les piles. Celles-
ci risqueraient d’exploser. Jetez les piles usées selon les
renseignements suivant le sceau du RBRC.
7. N’utilisez que les adaptateurs inclus avec ce produit.
L’utilisation d’un adaptateur dont la polarité ou la tension
serait inadéquate risque d’endommager sérieusement le
produit et mettre votre sécurité en péril.
Informations sur les adaptateurs électriques :
Adaptateur de l’unité du parent : Sortie : 5V DC 1A
VTech Telecommunications Ltd.
Modèle : VT05EUS05100
Adaptateur de l’unité du bébé : Sortie : 5V DC 600mA
VTech Telecommunications Ltd.
Modèle :
VT05EUS05060
Informations sur les piles rechargeables :
Zhuhai Great Power Energy Co., Ltd.
Li-ion battery, 3.6V, 2600mAh, 9.36Wh;
Model: ICR18650-2.6Ah-3.6V-1S1P
8. Lorsqu’ils sont branchés dans une prise de courant, les
adaptateurs secteur ont été conçus pour être orientés
correctement, soit à la verticale ou au plancher. Les broches
n’ont pas été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici est branché
dans une prise au plafond, sous une table ou dans un
meuble.
9. Pour les PRODUITS À BRANCHER À UNE PRISE DE
COURANT, la prise de courant doit être installée près du
produit, afin d’assurer une accessibilité sécuritaire à la prise
de courant.
10. Débranchez ce produit de la prise de courant avant de
procéder au nettoyage. N’utilisez pas de nettoyants en
aérosols. Utilisez un chiffon humide pour le nettoyer.
11. Ne coupez pas les cordons d’alimentation pour remplacer
les fiches, car ceci peut présenter un danger potentiel.
12. Ne laissez aucun objet reposer ni appuyer sur le cordon
d’alimentation. N’installez pas cet appareil dans un endroit
où l’on risque d’écraser le cordon d’alimentation ou de le
piétiner.
13. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur l’étiquette. Si vous ne connaissez
pas le type d’alimentation que vous possédez à votre
domicile, consultez votre marchand ou votre compagnie
locale d’électricité.
14. Ne surchargez pas les prises de courant murales ni les
rallonges électriques.
15. Ne placez pas cet appareil sur un chariot, meuble, trépied,
support de montage ni table chancelants.
16. Les trous et ouvertures du boîtier, situés à l’arrière de
l’appareil ou sous celui-ci, servent à aérer l’appareil.
Pour l’empêcher de surchauffer, ne bloquez sous aucun
prétexte ces ouvertures et n’empêchez pas l’aération
adéquate de l’appareil en le plaçant sur un lit, divan,
tapis ou toute autre surface similaire. De même, ne le
positionnez pas à proximité ni au-dessus d’une source de
chaleur ou d’un calorifère. De plus, ne placez pas l’appareil
dans un endroit avant de vous assurer qu’il y ait une bonne
circulation d’air.
17. N’enfoncez jamais d’objets à travers les ouvertures de
cet appareil, car ils pourraient entrer en contact avec
des points de tension dangereux ou causer des courts-
circuits qui peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide dans ce
produit.
18. Afin de réduire les risques d’électrocution, ne démontez
pas cet appareil, mais apportez-le dans un centre de service
autorisé. L’ouverture du boîtier ou le retrait de toutes pièces
que contient cet appareil, à l’exception de l’accès autorisé
à certaines portes ou ouvertures, risque de vous exposer à
des points de tension dangereux ou d’autres dangers. Un
remontage incorrect peut par la suite présenter des risques
d’électrocution.
19. Vous devriez tester la réception chaque fois que vous
mettez l’appareil en fonction.
20. Examinez les composantes afin de vérifier si celles-ci ne
sont pas endommagées.
21. Il existe un très faible risque de perte de confidentialité
avec certains appareils électroniques (autres écoute-bébés,
téléphones sans fils etc.). Pour l’éviter, s’assurer que le
produit n’a jamais été utilisé avant l’achat, réinitialiser l’unité
de façon périodique, éteindre l’écoute-bébé quand il n’est
pas en cours d’utilisation.
22. Les enfants devraient être supervisés afin de vous assurer
qu’ils ne jouent pas avec l’appareil.
23. Le produit n’est pas conçu pour être utilisé par des
personnes (incluant des enfants) aux capacités physiques,
sensorielles ou mentales réduites ou qui manquent
d’expérience et de connaissances, à moins qu’on leur
ait donné suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une personne
responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre
0˚ C (32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne
l’installez pas près d’une source de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur excessive
telle que la lumière du soleil ou au feu.
4. Avertissement - Risque de strangulation
- Les enfants se sont ÉTRANGLÉS dans des
cordons. Gardez ce cordon hors de portée
des enfants (à plus de 0,9 m). N’enlevez pas
cette étiquette.
5. Ne jamais placer le moniteur à l’intérieur du
berceau ou du parc de bébé. Ne jamais couvrir le moniteur
ou l’unité (s) portative avec un article tel une serviette ou
une couverture.
6. D’autres équipements électroniques peuvent produire des
interférences sur votre moniteur vidéo et audio. Tentez
d’installer votre moniteur vidéo ou audio à l’écart des
appareils électroniques tels que des routeurs sans fil, radios,
téléphones cellulaires, interphones, moniteurs, téléphones,
ordinateurs personnels, électroménagers et téléphones
sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une
firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans
fil portatifs et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des aliments et
drogues (FDA) des États-Unis, la firme WTR recommande aux
médecins:
Avis aux détenteurs de stimulateurs cardiaques
Vous devriez maintenir les dispositifs sans fil à au moins six
pouces du simulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement
sur le stimulateur cardiaque, tel que dans une poche de
chemise, lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de
risque pour les détenteurs de simulateurs cardiaques causés par
les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se
rapportant aux champs électromagnétiques (EMF) standard. Si
vous le manipulez correctement en suivant les instructions de ce
guide, son utilisation sera sécuritaire pendant de nombreuses
années, selon les meilleures évidences scientifiques dont nous
disposons aujourd’hui.
For cETL compliance only
Main
menu Sub-menu
Lullaby
Lullaby volume
• Adjust the baby unit’s speaker
volume when playing the
lullaby.
• Select one of the four melodies to
play, or stop a lullaby.
Night Light
• Turn on/off the night light.
Monitoring Mode (For VM3258-2 only)
Patrol mode
• Monitor your baby in PATROL
mode, where the screen will
cycle through display videos
streamed from all the linked
baby units (For VM3258-2 only).
• View the video from your
selected baby unit’s camera.
Main menu icons Adjust the sound sensitivity of the baby unit
You can choose to hear sounds from the baby unit all the time,
or to hear sounds that exceed a certain level. You can use the
parent unit to adjust the microphone sensitivity of your baby
unit. The higher the sensitivity level, the more sensitive the
baby unit is in detecting sounds that transmit to the parent unit.
The VOX sensitivity level is preset to the highest level.
VOX
Sensitivity
level Highest High Medium Low Lowest
Description The parent
unit speaker
is constantly
on, and you
will hear
all sounds
(including
background
noises) from
your baby’s
room.
The parent
unit speaker
turns on
for soft
babbling
and louder
sounds from
your baby.
It remains
quiet when
your baby
sleeps
soundly.
The parent
unit speaker
turns on
for loud
babbling
and louder
sounds from
your baby.
It remains
quiet when
your baby
makes soft
sounds.
The parent
unit speaker
turns on
for crying
and louder
sounds from
your baby.
It remains
quiet when
your baby
makes soft
sounds.
The parent
unit speaker
turns on
for loud
crying or
screeching
sounds from
your baby.
It remains
quiet when
your baby
makes soft
sounds.
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the
holder of a valid proof of purchase (“Consumer” or “you”)
that the Product and all accessories provided in the sales
package (“Product”) are free from defects in material
and workmanship, pursuant to the following terms and
conditions, when installed and used normally and in
accordance with the Product operating instructions. This
limited warranty extends only to the Consumer for Products
purchased and used in the United States of America and
Canada.
What will VTech do if the Product is not free from defects
in materials and workmanship during the limited warranty
period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service
representative will replace at VTech’s option, without charge,
a Materially Defective Product. If we choose to replace
the Product, we may replace it with a new or refurbished
Product of the same or similar design. We will retain
defective parts, modules, or equipment. Replacement of the
Product, at VTech’s option, is your exclusive remedy. VTech
will return the replacement Products to you in working
condition. You should expect the replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE
(1) YEAR from the date of purchase (90 days on products
purchased as Refurbished*). This limited warranty also
applies to the replacement Product for a period of either (a)
90 days from the date the replacement Product is shipped
to you or (b) the time remaining on the original one-year
warranty (90-day limited warranty on products that are
purchased as Refurbished*); whichever is longer.
*Refurbished products purchased from our online store
carry a 90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation,
fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration
or modification by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem experienced is
caused by signal conditions, network reliability, or cable or
antenna systems; or
4. Product to the extent that the problem is caused by use
with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair
from outside the United States of America or Canada, or
used for commercial or institutional purposes (including
but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see
item 2 below); or
8. Charges for installation or set up, adjustment of customer
controls, and installation or repair of systems outside the
unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our
website at www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features may
save you a service call.
Except as provided by applicable law, you assume the risk
of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the
transport of the Product(s) to the service location. VTech
will return replaced Product under this limited warranty.
Transportation, delivery or handling charges are prepaid.
VTech assumes no risk for damage or loss of the Product in
transit.
What must you return with the Product to get warranty
service?
1. Return the entire original package and contents including
the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or
oral communications related to this Product. VTech provides
no other warranties for this Product. The warranty exclusively
describes all of VTech’s responsibilities regarding the
Product. There are no other express warranties. No one is
authorized to make modifications to this limited warranty and
you should not rely on any such modification. State/Provincial
Law Rights: This warranty gives you specific legal rights, and
you may also have other rights, which vary from state to state
or province to province.
Limitations: Implied warranties, including those of fitness
for a particular purpose and merchantability (an unwritten
warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/
provinces do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including,
but not limited to lost profits or revenue, inability to use
the Product or other associated equipment, the cost of
substitute equipment, and claims by third parties) resulting
from the use of this Product. Some states/provinces
do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion
may not apply to you.
Please retain your original sales receipt as proof
of purchase.
Limited warranty
  • Page 1 1
  • Page 2 2

VTech VM3258 Mode d'emploi

Catégorie
Babyphones
Taper
Mode d'emploi

dans d''autres langues