VTech VM3251 Manuel utilisateur

VTech
Marque
VTech
Modèle
VM3251
Catégorie
Babyphones
Taper
Manuel utilisateur

Ce manuel convient également à

Note
• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and
should not be used as such.
Test your baby monitor
You may test the baby monitor before initial use, and at regular times thereafter.
Caution
• For hearing protection, make sure the
parent unit is more than 3 feet (1 meter)
away from both baby units. If you hear
any high-pitched noise, move the parent
unit further until the noise stops. You
can also press VOL- on the parent unit to
lower or reduce the noise.
1. Make sure your baby unit and parent unit are on.
2. The parent unit displays images from the baby unit.
• Speak towards the microphone of the baby unit.
You will hear the sound at the parent unit.
3. If you have two baby unit, view the image from one of them by pressing at the right
side of your parent unit. Then, repeat step 2.
Note
• When the parent unit displays No link to Camera, and the LINK LED light flashes, move the
parent unit closer to the baby units (observe the minimum distance of 3 feet / 1 meter). You can
also check if the baby unit is connected to a live power socket and switched on.
Tip
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the
baby units.
Positioning the baby monitor
Caution
• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the
baby’s crib or playpen.
Note
• To avoid interference from other electronic devices, place your baby monitor far away from devices
such as wireless routers, microwaves, cell phones and computers.
User’s manual
VM3251
VM3251-2
Video Monitor
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
Congratulations
on purchasing your new VTech product. Before using this product, please read Important safety
instructions.
This manual has all the feature operations and troubleshooting necessary to install and operate
your new VTech product. Please review this manual thoroughly to ensure proper installation and
operation of this innovative and feature-rich VTech product.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.
1 set for VM3251
2 sets for VM3251-2
Volume level control on baby unit
• Press VOL+ to increase the volume level of the lullaby on the baby unit.
• Press VOL- to decrease the volume level of the lullaby on the baby unit.
Notes
• Once the lullabies are played, the setting will be applied to the last viewed camera.
• The lullaby playback on the baby unit will be paused when receiving talkback from the parent unit.
Screen off timer
You can set the screen off time for the parent unit when there is no key press for a specific
time interval.
When the screen is turned off, you can still hear sound from the baby unit.
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press SELECT or .
3. Press or to choose the desired time period to automatically turn off screen
(5 min/30 min/60 min/OFF), then press SELECT to confirm your selection.
Monitoring mode * for VM3251-2 only
Every time the parent unit is turned on, it displays a baby unit in Single CAM mode. If there
are two baby units in your system, you can also monitor your baby in Patrol mode.
Single CAM The screen displays image of a single baby unit in full screen.
Patrol A single cam view that transitions to a different baby unit every 10 seconds.
To switch to another camera:
• Press to view the next baby unit.
To enter Patrol mode:
• Press PATROL to switch to PATROL mode if you are in SINGLE-CAM mode, and vice versa.
Monitor the temperature
Your baby unit monitors the temperature of your baby’s room with its built-in temperature
sensor. If the detected temperature is out of the preset temperature range, the parent unit
will display an alert message.
Set temperature range
You can set the desired room temperature alert range. The minimum temperature can be set
between 50 oF (10 oC) and 76 oF (24 oC). The maximum temperature can be set between 77 oF
(25 oC) and 102 oF (39 oC).
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press SELECT.
4. Press or to choose or , then press SELECT.
5. Press or to choose the desired minimum or maximum temperature, then press SELECT
to confirm your selection.
Temperature alert tone
You can turn on the temperature alert tone so that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press SELECT.
4. Press or to choose or , then press SELECT to confirm your selection.
Temperature format
You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC).
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press SELECT.
4. Press or to choose or , then press SELECT to confirm your selection.
Zoom
You can zoom in while viewing images from the baby unit.
• Press to zoom in.
• Press or to move the zoomed image upward or downward.
• Press or to move the zoomed image leftward or rightward.
• Press again to zoom out.
Pair extra new baby unit (VM3211)
You can add or replace any baby units (VM3211, purchased separately) to your VM3251/VM3251-2
Video Monitor with Adjustable Lens. You can pair a maximum of four baby units to your parent unit.
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press to select.
3. Press or to choose an empty baby unit slot ( , , or ), then press SELECT. The
parent unit screen displays .
What’s in the box
1
Connect and charge the battery 2 Before use
3
Using the baby monitor
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels 32
LCD 2.8” Color LCD
(QVGA 320x240 pixel)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Power requirements Parent unit: 3.6V Ni-MH battery
Baby unit power adapter: Output: 6V DC @ 500mA
Parent unit power adapter: Output: 6V DC @ 500mA
Technical specifications
Specifications are subject to change without notice.
© 2018 VTech Communications, Inc.
All rights reserved. 08/18. VM3251-X_CIB_V7
Document order number: 91-010414-060-100
1. Place the baby units more than 3 feet (1 meter) away from your baby.
2. Flip down the camera on the baby unit to adjust the angle according to your
preference.
3. Place the parent unit more than 3 feet (1 meter) away from the baby units.
Caution
• The default volume of your parent unit is level 4, and the maximum volume is level 5. If you
experience high-pitched screeching noise from your baby monitor while positioning:
- Make sure your baby units and parent unit are more than 3 feet (1 meter) apart, OR
- Lower the volume of your parent unit.
Operating range
The operating range of the baby monitor is up to 1000 feet (300 meters) outdoors
or 160 feet (50 meters) indoors. The actual operating range may vary depending on
the environmental conditions and other interferences such as walls, doors and other
obstructions.
Power on or off the baby unit
• Slide the ON/OFF switch to ON to turn on the baby unit. The POWER LED light turns on.
• Slide the ON/OFF switch to OFF to turn off the baby unit. The POWER LED light turns off.
Power on or off the parent unit
• Press and hold to turn on the parent unit. The screen turns on.
• Press and hold again to turn off the parent unit. The screen turns off.
Turn on or off the parent unit screen
You can turn on or off the parent unit screen without powering off the parent unit. You can
still hear sound from the baby units.
• Press LCD ON/OFF on the parent unit to turn off the screen.
• Press any key on the parent unit to turn on the screen again.
Adjust speaker volume
For parent unit:
• Press VOL-/VOL+ on the parent unit to adjust the speaker volume.
Note
• When the parent unit speaker volume is set to zero, appears on the screen and the light turns on.
For baby unit:
The baby unit speaker volume determines the talkback volume transmitted from your parent unit.
1. Press +/VOLUME/- on the baby unit to adjust the speaker volume.
Adjust LCD brightness
You can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press SELECT or .
3. Press or to choose the desired level of brightness, then press SELECT.
Lullaby
You can play the lullabies on the baby unit using the parent unit. On the baby unit, you can
control the volume level of the lullabies.
Playing lullabies
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose a lullaby, or choose to stop playing.
4. Press SELECT to confirm your selection.
4. Use a narrow-pointed object, such as a pen, to press PAIR on the bottom of the baby unit.
• The ON/OFF LED light at the side of baby unit flashes quickly when pairing.
When pairing is successful, the parent unit screen displays and the LINK light turns on. The
view of the newly paired baby unit in SINGLE-CAM mode will be shown on the parent unit. The
ON/OFF LED light on the new baby unit remains on.
Notes
• If pairing fails, the screen displays . Try the pairing process again.
• Only one baby unit can be paired at a time.
3
Using the baby monitor
Install the battery
The parent unit runs on rechargeable battery or AC power. To continuously monitor your
baby, make sure you use both battery and AC power at the same time. With the battery
alone, the parent unit can cordlessly run for a short time only.
NOTESNOTE
Notes
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent
possible leakage.
1. Press down on the battery compartment cover to pull it out.
2. Make sure the label THIS SIDE UP is facing up while inserting the battery
3. Push the battery compartment cover back until it secures into place.
Replace the battery
To replace the battery, press down on the battery compartment cover and pull it out, then
follow the steps above to install the battery.
Connect the baby monitor
NOTESNOTE
Notes
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to the switch controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are
not designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-
the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.
Charge the parent unit battery
When you have connected and turned on the parent unit, the battery will be charged
automatically. The battery icon indicates the battery status (see the following table).
NOTESNOTE
Notes
• The parent unit battery is fully charged after 11 hours of continuous charging.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
• The standby time varies depending on the volume level you set and your actual use.
Battery indicators Battery status Action
The battery icon is off and
displays.
No battery is installed
but operates using AC
power, or the battery
has been installed
incorrectly.
Install the parent unit battery.
Charge without interruption
(at least 30 minutes).
The screen displays Battery
low at Parent Unit and .
The light flashes.
The battery has very little
charge and may be used
for only a short time.
Charge
without interruption
(about 30 minutes).
The battery icon becomes
solid .The battery is fully
charged. To keep the battery charged,
connect it to AC power when
not in use.
THIS SIDE UP
THIS SIDE UP
3ft (1m)
3ft (1m)
> 3ft (1m)
Press .
10s
>3ft (1m)
PAIR
PAIR
DC 6V 500mA
FCC ID:
IC: 1135B-8
EW780
0061700
-0617-00
MANUFACTU
www vtech
www.vtechphones.com
1-800-595-9511
VTech Customer Service
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels 32
LCD 2.8” Color LCD
(QVGA 320x240 pixel)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Power requirements Parent unit: 3.6V Ni-MH battery
Baby unit power adapter: Output: 6V DC @ 500mA
Parent unit power adapter: Output: 6V DC @ 500mA
Status icons
Connection status
• or displays when strong signal strength is detected between the baby
unit and the parent unit.
• or displays when moderate or low signal strength is detected between
the baby unit and the parent unit.
Patrol mode
• Displays when the parent unit is in PATROL mode.
• For VM3251-2 only
or
or
or
Current view status
• Displays the baby unit number of the baby unit that is being viewed.
Zoom
• Displays when the current image on the parent unit has zoomed in.
Night vision
• Displays when the baby unit being viewed has activated the night vision
feature.
Lullaby
• Displays when a lullaby is playing.
Talkback
• Displays when talking back to the baby units from parent unit.
6-level sound indicator
Displays the sound level according to the scales of loudness when there is sound
transmitted from the baby unit.
• (1 to 2 bars) indicates low sound level detected by the baby unit.
• (3 to 4 bars) indicates moderate sound level detected by the baby unit.
• (5 to 6 bars) indicates high sound level detected by the baby unit (e.g.
baby crying loudly).
Mute alert
• Displays when the parent unit is talking to the baby unit.
or
Real-time temperature
• Displays the real-time temperature detected by the baby unit in Fahrenheit (oF)
or Celsius (oC) (e.g. 57
oF or 14
oC).
Battery status
• animates when the battery is charging.
• displays solid when the battery is fully charged.
• displays when the battery is low and needs charging.
AC power without battery
• Displays when the parent unit is connected to AC power without the battery.
Speaker volume
• Displays the parent unit speaker volume level while adjusting.
When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock
and injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.
4. This product is not intended for use as a medical monitor.
5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
6. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for
the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT207695) for the parent unit. Do not
dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC® seal.
7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
Baby unit power adapter: Output: 6V DC 500mA; Parent unit power adapter: Output: 6V DC 500mA.
8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
11. Unplug the power cords before replacing batteries.
12. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.
14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure
of the type of power supply in your home, consult your dealer or local power company.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back
or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or
over a radiator or heat register.
18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or
create a short circuit. Never spill liquid of any kind on the product.
19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility.
Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages
or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
20. You should test the sound reception every time you turn on the units or move one of the components.
21. Periodically examine all components for damage.
22. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery
monitors, cordless phones, scanners, etc.
23. Children should be supervised to ensure that they do not play with the product.
24. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety. SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 32oF and 104oF.
2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.
4. Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach
of children (more than 3 ft (0.9m) away). Do not remove this tag.
5. Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent
unit with anything such as a towel or a blanket.
6. Other electronic products may cause interference with your baby monitor. Try installing your baby
monitor as far away from these electronic devices as possible: wireless routers, radios, cellular
telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the pacemaker.
• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to
the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.
The RBRC® seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating
in an industry program to collect and recycle these batteries at the end of their useful lives, when taken
out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used Ni-MH batteries into the trash or
municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s
involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
RBRC® and 1 (800) 8 BATTERY® are registered trademarks of the Rechargeable Battery Recycling Corporation.
Mesures de sécurité importantes
Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie,
d’électrocution et de blessures corporelles, dont ceux qui suivent :
1. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
2. L’installation par un adulte est requise.
3. Ce produit a été conçu pour être un dispositif d’appoint seulement. Il n’est pas le remplacement d’une supervision responsable et adéquate
par un adulte et ne devrait pas être utilisé comme telle.
4. Ce produit n’est pas conçu pour être utilisé en tant que moniteur médical.
5. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de
cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.
6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque d’explosion si un autre type de batterie est utilisé pour l’unité
Parents. N’utilisez que le bloc-piles rechargeable inclus ou le bloc-piles de rechange (BT207695). N’incinérez pas les piles. Celles-ci
risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant le sceau du RBRC®.
7. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre votre sécurité en péril.
Adaptateur de l’unité du bébé : Sortie : 6V CC 500mA
Adaptateur de l’unité du parent : Sortie : 6V CC 500mA
8. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale
ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché
dans une prise au plafond, sous une table ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, afin d’assurer une
accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon
humide pour le nettoyer.
11. Débranchez les cordons d’alimentation avant de remplacer le bloc-piles.
12. Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car ceci peut présenter un danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser
le cordon d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que
vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité.
15. Ne surchargez pas les prises de courant murales ni les rallonges électriques.
16. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants.
17. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer,
ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou
toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus,
ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.
18. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou
causer des courts-circuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.
19. Afin de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du
boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous
exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.
20. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.
21. Examinez les composantes afin de vérifier si celles-ci ne sont pas endommagées.
22. Soyez avisé de la perte de la confidentialité lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par
d’autres moniteurs de bébé, des téléphones sans fil, des scanneurs, etc.
23. Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.
24. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales
réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre 0˚ C (32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source
de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.
4. Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, àau moins 1 mètre (3
pieds) de l’enfant ou du berceau, pour éviter tout risque de strangulation.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)
portative avec un article tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer
votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones
cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
• Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci
est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent
dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez
correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons aujourd’hui.
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the
Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship,
pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product
operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United
States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period
(“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without
charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we
choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will
retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive
remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces
a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or
replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you
or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal
operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service
representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna
systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed,
altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for
commercial or institutional purposes (including but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In
Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save
you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return
repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech
assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or
proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the
cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of
Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of
purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral
communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes
all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty
gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty
that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech
be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or
revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third
parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor
is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge
the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby
units, the CEC battery charging testing mode is activated while it is powered off and charging.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with
the FCC criteria. Caution: This Transmitter must be installed to provide a separation distance of at least 20cm from all persons. The
transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference, including interference that may cause undesired operation.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were
met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
FCC RF radiation exposure statement
The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should
be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect
to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
The RBRC® seal For cETL compliance only Limited warranty
California Energy Commission battery
charging testing mode
The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark
room. When the baby unit being viewed detects low light levels, the infrared LEDs are
switched on automatically. The images from the baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting to
the dark environment.
• When the infrared LEDs are on, the images are in black and white. This is normal.
Tip
• Depending on the surroundings and other interfering factors, like lightings, objects, colors and
backgrounds, the display resolution may vary. Adjust the baby unit’s angle or place the baby unit at a
higher level to prevent glare and blurry display.
Night vision
Your baby monitor comes ready for tabletop use. You can also choose to mount your baby
monitor on the wall. See Mount the baby unit on dry wall (optional) in the Quick Start Guide
for the wall mounting instructions.
Mount the baby unit (optional)
FCC and IC regulations
Why don’t the
power-on light of the
baby unit and parent
unit go on when I switch
on the units?
Perhaps the parent unit is not connected to the power. Insert the appliance plug into
the parent unit and put the adapter in a wall socket. Then, press and hold to switch
on the parent unit and to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug into
the baby unit and put the adapter in a wall socket. Then, slide the ON/OFF switch to
ON to switch on the baby unit and to establish connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by a wall switch.
Make sure the battery is correctly installed in your parent unit.
You may have used the battery for a long time. Replace a new battery.
Why is my screen in
black and white?
The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors,
like lightings, objects, colors and backgrounds may affect the image quality on your
parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level
to prevent glare and blurry display.
Why does the baby
monitor produce a
high-pitched noise?
The parent unit and baby units may be too close to each other.
• Move the parent unit away from the baby units until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent
unit beep?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit for up to 11 hours.
The temperature of your baby’s room may be too high or too low.
The ON/OFF light on the
baby unit flashes and the
parent unit displays .
Follow below steps to pair the baby unit. Make sure both parent unit and baby unit are
on before pairing.
1. Press MENU when the parent unit is idle.
2. Press or to choose , then press to select.
3. Press or to choose an empty baby unit slot ( ,
, or ), then press SELECT. The parent unit screen displays .
4. Use a narrow-pointed object, such as a pen, to press PAIR on the bottom of the
baby unit.
• The ON/OFF LED light at the side of baby unit flashes quickly when pairing.
When pairing is successful, the parent unit screen displays and the LINK light turns
on. The view of the newly paired baby unit in SINGLE-CAM mode will be shown on
the parent unit. The ON/OFF LED light on the new baby unit remains on.
• If pairing fails, the screen displays . Try the pairing process again.
• Only one baby unit can be paired at a time.
I have accidentally
unpaired my baby unit.
Why don’t I hear a
sound/Why can’t I hear
my baby cry?
The parent unit speaker volume may be too low. Press VOL+ to increase the volume.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet).
Other electronic products may cause interference with your baby monitor. Try
installing your baby monitor as far away from these electronic devices as possible.
If you power on only one baby unit, your parent unit may display , and the LINK
LED light flashes. Press VIEW to switch to the baby unit you have powered on.
Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your
question, visit our website at www.vtechphones.com, or contact 1 (800) 595-9511 for customer service.
Why does the baby
monitor not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby units and the parent unit.
2. Remove the batteries in the parent unit. Then, install the batteries again.
3. Wait a few seconds before connecting power back to the baby units and the parent unit.
4. Turn on the baby units and the parent unit.
5. Wait for the parent unit to synchronize with the baby units. Allow up to one minute
for this to take place.
Frequently asked questions (con’t)
Frequently asked questions
Parent unit icons
Important safety instructions
Parent unit overview
1 LED lights
Indicate the different statuses of the
parent unit. For details, refer to Parent
unit lights.
2LCD display
3 Zoom
• Press to zoom in or out while
viewing image.
4
• Press to change the screen to view
images from different baby units.
• For VM3251-2 only
LCD ON/OFF
• Press and hold to turn on or off the
LCD screen.
5MENU/SELECT
• Press to enter the menu or
submenu.
• While in a sub-menu, press to
choose an item, or save a setting.
6Microphone
7
• While in a menu, press to scroll up,
or to enter an item’s sub-menu.
• While zooming, press and hold to
move the zoomed image upward.
• While in a menu, press to scroll
down.
• While zooming, press and hold
to move the zoomed image
downward.
• While in a menu, press to choose
the next item on the left, or enter
into the submenu, if any.
• While zooming, press and hold to
move the zoomed image leftward.
• While in a menu, press to choose
the next item on the right, or return
to the main menu while in submenu.
• While zooming, press and hold to
move the zoomed image rightward.
8 On/off
• Press and hold to power on.
• Press and hold again to power off.
9 TALK
• Press and hold to talk to the selected
baby unit.
10 VOL-
• Turn down the volume when the
speaker is on.
11 VOL+
• Turn up the volume when the
speaker is on.
12 Speaker
13 Power jack
14 Battery compartment cover
15 Stand
1Light sensor
2Camera
3Infrared LEDs
4-/VOLUME/+
• Press to adjust the speaker volume.
It determines the talkback volume
transmitted from your parent unit.
5Microphone
6ON/OFF LED light
• On when the baby unit is turned on
and is paired to the parent unit.
• Flashes when the baby unit is not
being viewed; or when the link to the
parent unit is lost.
7 ON/OFF switch
• Slide to turn on or off the baby unit.
8Temperature sensor
9Speaker
10 Wall mount holes
11 Power Jack
12 PAIR
• Your baby units and parent unit
provided are already paired.
• Press on the accessory baby units
(VM3211, purchased separately) to pair
to the parent unit.
Baby unit overview
Main menu icons
Brightness
You can change the brightness of the parent unit screen.
Pairing baby unit
The baby unit and parent unit provided are already paired. You can add or replace baby
units (VM3211, purchased separately) to your baby monitor system.
LCD screen off timer
You can set a specific time to screen off your parent unit.
Temperature
You can choose to set the maximum/minimum temperature and turn on the
temperature alert tone so that the parent unit beeps whenever the room
temperature detected by the baby unit falls outside of the desired temperature
range.
You can also choose to display the temperature in Fahrenheit (oF) or Celsius (oC) on
your parent unit.
Lullaby
You can select, play, or stop a lullaby.
Warning icons and messages
/No link to Camera The selected baby unit is out of range or is turned off.
/Battery low at Parent Unit The battery is empty and needs to be recharged.
Pairing is completed.
Camera switching, pairing is in progress.
Camera switching, pairing is failed.
/Temperature too high
or
/Temperature too low
The temperature detected by the baby unit is higher/
lower than the desired temperature alert range.
or or or The baby unit is unpairing from the parent unit.
The parent unit is searching for baby units.
To keep this product working well and looking good, follow these guidelines:
• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
General product care
b
c
d
e
f
n
o
l
k
j
m
a
i
h
g
When you are not going to use the baby monitor for some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place.
Storage
b
c
d
e
f
a
i
h
g
e
d
a
b
c
DC 6V 500mA
MANUFACTURED IN CHINA
www.vtechphones.com
VTech Customer Service
1-800-595-9511
FCC ID: EW780-0617-00
IC: 1135B-80061700
4H20
I.T.E.
PAIR
e
d
a
b
c
h
i
f
g
j
k
l
DC 6V 500mA
MANUFACTURED IN CHINA
www.vtechphones.com
VTech Customer Service
1-800-595-9511
FCC ID: EW780-0617-00
IC: 1135B-80061700
4H20
I.T.E.
PAIR
e
d
a
b
c
h
i
f
g
j
k
l
Parent unit lights
LINK • On when the parent unit is linked to the baby unit.
• Flashes when the link to the baby unit being viewed is lost.
• On when the parent unit is connected to AC power, or the battery is charging.
• Flashes when the parent unit battery is low and needs charging.
• Off when the parent unit is disconnected from AC power.
• On when the parent unit is talking to the baby unit.
TALK • On when the parent unit is talking to the baby unit.
  • Page 1 1
  • Page 2 2

VTech VM3251 Manuel utilisateur

VTech
Marque
VTech
Modèle
VM3251
Catégorie
Babyphones
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes