Electrolux WA71-305DG Manuel utilisateur

Models:

WA51-303 & WA51-304 series

WA71-304 & WA71-305 series

Instruction book

Mode d’emploi

OPERATING MANUAL

Thank you for choosing the Electrolux WELL A7 / A5 series air purifier. Always use

original Electrolux consumables, accessories and spare parts to get the best results

out of your unit. This appliance is designed with the environment in mind and hence

all plastic parts are marked for recycling purposes.

GENERAL SAFETY INFORMATION

This USER MANUAL provides specific operating instructions for your model OR

series. Use the unit only as instructed in this manual. These instructions are not

meant to cover every possible condition and situation that may occur. Common

sense and caution must be practiced when installing, operating, and maintaining

any appliance.

WARNING! - CHILDREN & VULNERABLE PEOPLE SAFETY

Risk of suffocation, injury or permanent disability. Keep all packaging away from

children.

This appliance can be used by children aged from 8 years and above and persons

with reduced physical, sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruction concerning use of the

unit in a safe way and understand the hazards involved.

Cleaning and user maintenance shall not be made by children without supervision.

Children shall not play with the unit. Children under 3 years of age should be kept

away from the unit unless continuously supervised.

CAUTION! – AVOID INJURY OR DAMAGE TO THE UNIT OR PROPERTY

Do not direct airflow at fireplaces or other heat related sources as this could

cause flare ups.

Do not climb on or place objects on the unit.

Do not hang objects off the unit.

Do not place containers with liquids on the unit.

Turn OFF the unit at the power source when it will not be used for an extended

period.

Do not block or cover the air intake area, fan area and air outlet grill.

Ensure that any electrical/electronic equipment is at least 30cm away from the unit.

GB

CS

DA

FI

FR

DE

HR

HU

IT

NO

PL

RO

SK

SL

SR

SV

TR

www.electrolux.com

2

CAUTION! – WALL MOUNTING: AVOID INJURY OR DAMAGE TO PROPERTY

Always use appropriate screw and plastic plug for wall hang hook, depending on the

wall material (e.g. nailable plug with screws for concrete OR expandable plug with

screws for drywall, etc.). If you are not sure of the type of wall, have a qualified

builder OR constructor inspect and recommend the correct screw and plug type

according to local or national building standards.

Do not, under any circumstances, use the wall hang hook with only one screw.

Always use appropriate safety precautions and protective gear while drilling holes

into the wall OR handling such equipment (e.g. safety gloves, dust mask, etc.).

Do not pull on OR tug on the unit from the power cord while it is wall mounted. Please

ensure power cord is snug to the wall and the floor to avoid any undue tangling of

objects with the cord and thus accidental tugs to the unit.

Ensure the wall hang hook is secured to the wall firmly and at the correct angle (e.g.

parallel to the floor without any leaning) for best results.

If unsure of whether the wall hang hook has been secured correctly on the wall,

before mounting the unit, please test the hook by a) applying some pressure on it

from the top with your hands to see if it buckles and b) tugging the hook towards you

with some pulling motion to see if screws come loose.

INFORMATION ABOUT RADIO

WiFi working frequency and maximum output power: 2.4 GHz; 15dBm

RFID working frequency and maximum output power: 13.56 MHz; 30dBm ± 10%

Power consumption of the product in network standby is less than 2.0W

ELECTRICAL SAFETY INFORMATION

WARNING! – AVOID FIRE HAZARD OR ELECTRIC SHOCK

This unit can be used in 50Hz or 60Hz power supply without any change.

Do not use an extension cord or an adaptor plug.

Do not remove any prong from the power cord. Do not pinch, bend, or knot the

power cord.

Do not cut or damage the power cord. If the supplied power cord is damaged, it

should only be replaced by Electrolux, its service agent or similarly qualified persons.

This unit contains no user serviceable parts. Always call an authorized Electrolux

servicer for repairs.

Do not, under any circumstances, cut, remove or bypass the grounding prong (see

picture 26 on page 3; for UK see picture 27). If you are not sure the outlet is

adequately grounded or protected by a time delay fuse or circuit breaker, have a

qualified electrician install the proper outlet according to the National Electrical Code

3

www.electrolux.com

OR applicable local codes and ordinances.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity

of this or any other appliance. Read product labels for flammability and other

warnings.

Do not let water or any other liquid or flammable detergent enter the unit to avoid

electric shock and/or a fire hazard. Be sure to unplug he unit before cleaning.

Never unplug the unit by pulling on the power cord. Always grip the plug firmly and

pull straight out from the receptacle.

CAUTION! – AVOID SERIOUS INJURY OR DEATH

Do not insert or place fingers or objects into the air discharge area or front facing

grille of the unit.

Do not start or stop the unit by unplugging the power cord or turning OFF the power

at the electrical box.

In the event of a malfunction (sparks, burning smell, etc.), immediately stop the

operation, disconnect the power cord, and call an authorized Electrolux servicer.

Do not operate the unit with wet hands.

Do not pull on the power cord.

Do not touch the fan blade when removing the filter(s).

DISPOSAL

This symbol on the unit or on its packaging indicates that the unit may

not be treated as household waste. To recycle your unit, please take it to

an official location where they can remove and recycle the battery and

electric parts in a safe and professional way. Follow your country’s rules

for the collection of electrical products and rechargeable batteries.

BEFORE STARTING

Read this manual carefully and pay special attention to safety information.

Pay special attention to the CAUTION sections!

Check that all key components & parts described are included.

www.electrolux.com

4

KEY COMPONETNS OF WELL A7 / A5 SERIES AIR PURIFIERS

1

Removable & customizable front panel

14

Power cord cavity

2

Front panel magnets

15

Fan motor cavity, grill

3

Mesh pre-filter

16

RFID tag(s)

4

Ultrafine particle filter

17

Front panel hooks

5

www.electrolux.com

5

VOC carboner

18

POWER bun (ON/OFF)

6

Air quindic

19

MODE buon

7

UI D: Useerface)

20

Mode disp

8

Removabeop h for carrng

21

er change icon

9

Air oue

22

eon

10

ng & hanging

23

WiFi icon

11

Sensor box

24

Ionizer icon

12

Sensor window

25

d ock icon

13

Removabe fee x2

26

FAN SPEED sider & indor

NOTE: Your speciﬁc model may not have all the components and features listed within this USER MANUAL. Please

check the product packaging OR the product speciﬁcaon page on our website for exact details of your model.

Electrolux reserves the right to change informaon contained herein without noce.

www.electrolux.com

6

2

3

Min. 20 cm

Eye level

4

5

Min. 30 cm

Min. 20 cm

6

789

3

RFID tag

1

7

www.electrolux.com

10

11

12

14 15

13

18

19

20

21

22

23

24

16

17

UNBOXING & SETUP – picture pages 6-7

Please be careful while unboxing the air puriﬁer. The unit has several detachable

components which may have come loose in transport, so open the box with care and

while placed on a large ﬂat surface OR the ﬂoor.

1. Gently remove the unit (e.g. with top handle when available) and the ancillary

components from the main box. Remove the plas�c packaging and discard as per

safety and local recycling instruc�ons.

2. If wall moun�ng:

a. Please review safety instruc�ons under the GENERAL SAFETY sec�on

before proceeding.

b. Iden�fy a spot on the wall where you would like to mount the unit. The

spot should be at least 20 cm below eye level when standing fully upright

(even lower is ideal & recommended), for op�mal viewing as well as

cleanability under the unit. Also ensure that nearest power socket is max

1,5 mts away and that there is a clearing of at least 20 cm between right

side (sensor window) of the unit and other nearby surface.

c. Gently place the provided hook ﬂat against the surface of the wall and

with a pencil mark the two spots where screws are to be drilled. The hook

www.electrolux.com

8

26 27

28 29

25

should be placed such that the protruding tip (without the holes) is on

the top (refer to picture #2).

d. Depending on the wall, please use appropriate drill to make two holes

into the wall at the identified marks; and insert any plugs as needed.

e. Depending on the wall, please use appropriate screws for following step.

Place the hook flat against the surface of the wall, so that the holes are

concentric and the hook sits parallel to the floor without any inclination,

and then tighten the screws till the hook is securely in place and does not

move if tugged.

f. Lift the unit and place it onto the hook such that the top of the hook

securely fits into the inbuilt grip at the back of the unit.

g. Gently adjust the unit to remove any inclinations, just like a painting.

Ensure that the unit sits flat up against the wall.

h. When dismounting the unit, remember to disconnect the power cord

from the wall socket first.

3. If placing it on the floor:

a. Take the cylindrical feet and screw them into the unit by rotating

clockwise till you hear a click (or get some resistance).

b. Lift the unit and place it next to the power socket to be used.

c. Ensure a clearance of at least 30 cm between front (air inlet) and at least

20 cm between right side (sensor window) of the unit and other surfaces.

Also ensure ample free space above the top (air outlet grill), so the unit

can operate at its best in spreading pure air through the room.

d. When wall mounting, please remove the cylindrical feet from the base of

the unit for more efficient air distribution.

4. Remove the front panel by gently pulling it away from the unit with both hands.

5. Take out the mesh pre-filter, ultrafine particle filter and VOC carbon filter layers

and remove all plastic packaging. Discard as per safety and local recycling

instructions.

6. Place the filter layers back into the unit in the same order as originally found (i.e.

VOC carbon filter goes in first). While inserting, place take care to hold the filter

so that the RFID tag on the filter is located at the top-right – it should be near the

senor box hatch.

7. Attach the mesh pre-filter and the front panel back to the unit.

8. Plug the unit’s power cord to the nearest power socket so that the POWER button

9

www.electrolux.com

on the product UI gets illuminated.

9. For best results, operate the unit in an enclosed area with doors & windows

closed when feasible.

FIRST & ONGOING USE – picture pages 6-7

TURNING ON

10. Tap the POWER button once to turn ON the air purifier

NOTE: At every new run, it will take about 10 seconds for the sensors to calibrate and analyze the air quality before

ramping up to the appropriate fan speed. During this time, the air quality indicator will pulsate slowly in white.

CHANGING MODES & FAN SPEEDS

11. Tap the MODE button once to toggle between the two modes: SMART and

MANUAL

SMART: This is the default mode the unit will start in. In the SMART mode the

unit will utilize the sensor data as input to decide on the appropriate fan speed

and the UI display’s type & intensity level. The fan speed cannot be adjusted

manually by the user under this mode. Please see the AIR QUALITY INDICATOR

section for more details.

NOTE: The AQI light will turn off completely in a dark room when the unit is in smart mode, so as not to disturb.

MANUAL: In the MANUAL mode the unit will utilize the sensor data as input only

to show the air quality level via the air quality indicator but will not self-adjust

the fan speed. This mode is best utilized for a quick burst of cleaning, especially

when the user anticipates an increase in particulate matter in the room due to

household chores (e.g. vacuuming).

12. While in MANUAL mode, tap and scroll on the fan speed slider to adjust the speed

of cleaning – left most side being the lowest and right most side being the highest

speed.

NOTE: The unit will ramp up OR down to chosen speed setting gradually. The slider also acts as the indicator for the

current fan speed.

13. STANDBY & WiFi OFF: The air purifier is designed with ECODESIGN principles in

mind and hence will aim to limit power consumption to under 2.0W when unit is

powered OFF (unless user permission to override). When unit is powered ON, if

it has no WiFi connectivity OR is not onboarded, the WiFi radio signal will

automatically turn OFF after 30 minutes to conserve power – to bring the WiFi

www.electrolux.com

10

radio signal back ON manually please initiate ONBOARDING (step 21 only) or

unplug and then plug it back in to the socket.

FEATURE ICONS AND INDICATORS

NOTE: Not all indicators OR feature icons might be available on your model. Please consult packaging information or

the product specifications on the website for details on available features.

14. FILTER CHANGE: The high efficiency filter(s) in the unit cannot be washed, they

can only be replaced. The filter change icon will light up to remind you to

change your filter(s). Your air purifier may be equipped with more than one filter,

so please refer to the Wellbeing App for details on which filter layer is to be

replaced. Always ensure the plastic protective bag is removed from the filter

before its use in the unit. After the used filter is replaced, the filter change icon

will turn off automatically and no reset action is needed.

15. ALERT: The alert icon will light up to alert you of a possible electrical or

electronic error with your unit. Please refer to the Wellbeing App for details on

the error type, component details and any mitigating actions. More details can

be found in the ERRORS & TROUBLESHOOTING section below.

16. CHILD LOCK: The unit is equipped with a safety lock feature to disable the product

UI to avoid unintended pressing. The child lock feature can be toggled ON/OFF

via the Wellbeing App or by long pressing for 5 seconds the POWER and MODE

button simultaneously. The child lock icon will light up when the feature is

activated.

17. IONZIER: The unit is equipped with an ionizer module, which when enabled

generates negative ions to further aid with the air purification process. The

ionizer is OFF by default and can only be toggled ON/OFF via the Wellbeing App.

When the feature is activated the ionizer icon will light up. For more details on

how an ionizer helps reduce airborne particles, please refer to the product

information page on the website.

18. WiFi: The unit is equipped with a WiFi module, which enables remote control and

access to many more features including time-based tracking of your indoor air

quality data. When the unit is connected to the home WiFi, this icon will light

up. If the icon is blinking, it indicates a temporary loss of WiFi connectivity –

please refer to the Wellbeing App for more details.

NOTE: Download our Wellbeing App and follow the step-step onboarding instructions to bring the air purifier online.

11

www.electrolux.com

19. AIR QUALITY INDICATOR: The unit is equipped with an air quality sensor(s). The

laser-based particulate matter (PM) sensor is a high precision particle sensor that

can detect PM1, PM2.5 and PM10 levels. The air quality indicator will visually –

with the aid of a color scale - show the real-time air quality as per table below.

When in SMART mode, the air quality level will also determine the fan speed as

per table below.

NOTE: Please ensure regular cleaning of the sensor window to ensure it does not get clogged with dust and sensors

keep performing accurately. Also ensure optimal humidity levels (between 35-80%) for accurate reading from the

sensors.

LIGHT COLOR

PM 2.5 (μg/m3)

AIR QUALITY STATUS

FAN SPEED

White

Calibrating | Onboarding

Green

0 - 12

Very Good

2

Yellow

13 - 35

Good

3

Orange

36 - 55

Poor

4

Red

56 - 150

Very Poor

5

Purple

151 – 250

Bad

5

Maroon

>250

Very Bad

5

ONBOARDING – picture pages 6-7

NOTE: Some steps in the onboarding flow may have changed, please follow step-step instructions in the latest version

of the App as reference in case of discrepancy. Please ensure home WiFi is running on 2.4 GHz band and not 5 GHz

band, as this will not be recognized by the air purifier.

20. Please find the Wellbeing App in the iOS App or Google Play store, download it,

sign up and login to the App. Here you will be able to ‘Add a device’ to the App

and follow the step-step instructions for onboarding the unit – steps below are

indicative.

21. After plugging the unit into the power socket, please long press the POWER

button for 5 seconds until the WiFi icon starts blinking rapidly – this

indicates that the unit’s hotspot is activated and is ready for being connected to

the WiFi.

22. Head over to the Wellbeing App and using the phone’s camera to scan the WiFi

barcode. The WiFi barcode can be found on the rating label sticker on the unit

(typically after the mesh pre-filter, reference image 7). You can also manually

enter the digits under the barcode into the App if scanning it does not work.

23. Connect the App to the unit’s hotspot.

www.electrolux.com

12

24. Choose the 2.4 GHz home WiFi that the unit should connect to from available list

and then enter the password for this home WiFi into the App – wait for the unit

to establish a connection.

25. Complete the steps of naming your newly onboarded air purifier!

26. Later, if you would ever like to reset the WiFi credentials stored on your unit

please long press the POWER button for 5 seconds until WiFi icon starts

blinking (i.e. like step 20, hotspot activated). While in this state, again, long press

the POWER button for 5 seconds until WiFi icon stops blinking and is not

lit. Unit’s WiFi settings are now reset and it will not aim to connect to your WiFi

network.

CLEANING, CARING & STORAGE – picture pages 6-7

NOTE: Always unplug the air purifier before cleaning to prevent shock or fire hazards. Never use abrasive, harsh

detergents OR wax for cleaning the unit. The high efficiency filters cannot be washed, they must always be replaced

when at the end of life.

CLEANING & CARING

27. Ensure the sensor window is kept unclogged for optimal performance of the unit.

It is natural for dust to accumulate in this area, hence ensure regular (e.g. once

per 4 weeks) vacuuming of the sensor window with a vacuum cleaner that has a

narrow nozzle/brush.

28. The plastic parts of the unit should be cleaned with an oil-free dry cloth. For stains

on plastic parts, use a slightly damp soft microfiber cloth to gently rub against the

stain.

29. The fabric attached to the front panel should be wiped with an oil-free dry cloth

or by using a vacuum cleaner with a soft brush to avoid breaking of the fibers.

The area around the air inlet on the front of the unit may accumulate more dust

than some other parts and hence may require more frequent cleaning to ensure

optimal performance.

STORAGE

30. When storing away, besides unplugging the unit and winding the power cord

loosely around the bottom feet, ensure that unit including the high efficiency

filters and the fabric front panel are covered up to avoid accumulation of dust.

13

www.electrolux.com

REPLACING FILTERS – picture pages 6-7

NOTE: The filters – except for the mesh pre-filter - cannot be washed and must always be replaced when at end of life.

The WELL A7 / A5 series air purifiers have a variety of filters to choose from, tailored to your lifestyle needs. Each filter

layer is equipped with a smart RFID tag to uniquely identify it as well as to track its usage over time. Head over to the

Wellbeing App or the product information page on our website for a guide on choosing the appropriate filter for your

needs.

31. For the best experience and to secure an uninterrupted use of the air purifier,

please monitor the filter’s remaining lifetime in the Wellbeing App and order a

replacement filter in advance of the lifetime hitting 0%. If you have notifications

enabled, the Wellbeing App will inform you when the filter life is close to end of

life (e.g. at 5%).

32. When one or more of the filters is at end of life, the filter change icon will light

up on the product UI to indicate the need for replacement. Please head over to

the Wellbeing App to correctly identify which filter is at end of life and needs

replacement. When filter is at end of life, the unit’s fan speed may be capped in

SMART mode.

33. The used filter might be heavily coated with dust and particulate matter so before

opening the front panel, please ensure a disposable bag or packaging is at hand to

place the used filter in.

34. Remove the front panel and the mesh pre-filter and put them aside. Next remove

the filter layer which is at end of life and place it in the disposable bag at hand.

35. Next, please remove the plastic packaging from the replacement filter and insert

the filter in the appropriate place. Please ensure the VOC carbon filter goes in

first inside the unit, followed by the ultrafine particle filter. Reinsert the mesh

pre-filter and close the front panel. The filter change icon on the product UI will

no longer be lit and the Wellbeing App will indicate the same, with a new filter

lifetime reading.

NOTE: In case the change is only reflected on the product UI and not the Wellbeing App, please restart the App and

the unit, before further troubleshooting.

36. Discard the used filter as well as any plastic packaging according to local recycling

guidelines. The RFID tags contain circuitry and hence are to be disposed

separately from the rest of the filter.

www.electrolux.com

14

CUSTOMIZING – picture pages 6-7

The WELL A7 / A5 series Air Purifier was designed with a unique form and aesthetic

sense to ensure it fits in with your home and its furnishings, unlike other appliances.

In addition, the series comes with many customization kits for the unit that add to

the aesthetics but also functionality of the unit.

TOP HANDLE CUSTOMIZATION

The polyurethane leather (PU) handle at the top of the unit is attached to the unit by

way of two screws. Follow the steps below to attach or replace an existing top handle.

37. If you are replacing an existing top PU handle:

a. Remove the two screws, twisting counterclockwise and set aside along

with existing handle.

b. Remove any protective plastic packaging from the new handle and fit it

onto the unit by tightening the screws, twisting clockwise, till you meet

some resistance. Ensure a snug fit with no gap in between the unit and

the screw.

c. Test out the handle by lifting the unit 5-6 cm above the ground with it

and giving it a gentle shake.

38. If you are adding a top handle for the first time:

a. At the top of the unit, in between the product UI & the air outlet grill you

will find two circular cavities secured with a rubber plug. Uncover the

cavity by removing these rubber plugs from the unit by gently pulling on

the sides of the plug.

b. Follow the steps 37b. and 37c (above).

FRONT PANEL CUSTOMIZATION

The look of the front panel can be customized with a fabric cover to help accentuate

it but also to ensure the unit blends well with the decor of the room. The fabric cover

has an elastic seam that helps secure it to the front panel, hence no screws or staples

are necessary for its installation.

39. Please detach the front panel from the unit and if it already has a removable

fabric cover please gently take it off the panel – ensuring not to bend the panel.

NOTE: Some models in the WELL A7 series come with a fabric permanently attached to the front panel, this fabric is

not removable from the panel, but you can still customize the panel with another fabric cover on top of the existing

fabric.

15

www.electrolux.com

40. Remove any plastic packaging from the new fabric cover to be used.

41. Starting at the top left corner of the front panel, tuck the elastic band behind the

panel and while holding that corner in place work your way with the other hand

to the top right corner while continuously tucking the elastic band of the fabric

cover behind the edge of the panel. Now pull the fabric cover towards the bottom

edge of the panel and securely tug the rest of the fabric edge behind the bottom

part of the panel.

42. Smooth out any wrinkles on the fabric cover by pushing against the wrinkles.

43. Attach the front panel with the newly fit fabric cover back to the unit and check

the edges to ensure there is no blockage of the air inlet area.

NOTE: Customizable fabric covers are machine washable, as per the care instructions provided with the kit. It is

important that the elastic band along the edges of the fabric cover is unbroken and tight as it helps ensure an optimum

flow of air into the unit, with minimal decrease in performance. If you notice that the elastic band is broken or very

loose, it is time to replace the fabric cover.

FEET CUSTOMIZATION

The thermoplastic elastomer (TPE) feet are attached to the unit by way of inbuilt

screws. The feet – like the top handle – are detachable. Follow the steps below to

attach or replace an existing set of feet.

44. Place the unit flat on its back, so the front panel faces the ceiling. Unscrew the

existing feet, if any, by twisting counterclockwise.

45. Remove any protective plastic covering the new set of feet.

46. Gently nudge the inbuilt screw of the new feet into the cavity at the bottom of

the unit and secure them by twisting clockwise till you meet some resistance.

47. Test out the stability of the feet by placing the unit back upright and lifting it

about 5-6 cm above the ground and giving it a gentle shake.

www.electrolux.com

16

ERRORS & TROUBLESHOOTING

The table below is only a limited list. For the latest and complete section on

troubleshooting, FAQ and error guide please refer to the corresponding section on

our website or the Wellbeing App.

#

ISSUE

TROUBLESHOOTING

NOTES

1

The air purifier’s

alert icon is lit

If you have just bought the unit OR inserted new

filter(s), please ensure that the filter(s) are

positioned in the correct way for the RFID tags to be

read by the sensor (refer to point 6 within

ONBOARDING & SETUP section above).

Generally, the unit comes with a variety of

sophisticated sensors, electronics and other

electrical components and if one of these is

malfunctioning, you will see the alert icon on the

product UI light up. For more details on steps to

resolve, please head over to the Wellbeing App and

check for details whenever you see this icon lit.

Please have at hand

the unit’s PNC and

SERIAL number when

calling for support.

2

The air purifier is

running at max

fan speed all the

time for extended

periods

If in MANUAL mode, please check the fan speed

slider on the product UI or within Wellbeing App and

adjust it to desired level.

If in SMART mode, please check air quality indicator

on the product UI or within Wellbeing App – if all PM

values are constantly showing 999-1000 without any

reduction then most likely the sensor is clogged.

Please use a vacuum cleaner to clean the sensor via

the sensor window – detailed instructions in

CLEANING, CARING & STORAGE section above.

The PM sensor in

the unit is highly

accurate and

sensitive and it is

normal for the

purifier to react to

poor air quality by

ramping up the

fan speed – to get

your indoor air

quality back to

safe levels.

17

www.electrolux.com

3

The air purifier is

running at lowest

fan speed all the

time for extended

periods

If in MANUAL mode, please check the fan speed

slider on the product UI or within Wellbeing App and

adjust it to desired level.

If in SMART mode, please check air quality indicator

on the product UI or within Wellbeing App – if all PM

values are constantly reading very good without any

increase then this is normal behavior for the unit -

your air quality is very good! If the PM2.5 value is high

and the unit is still operating at lowest fan speed,

then please check filter change icon on the product

UI or within Wellbeing App and if lit please replace

used filter with a new one, this should resolve the

specific fan speed issue.

If neither of the above steps OR instructions in the

Wellbeing App help, please refer to item 9 in the

table.

The unit is designed

so that when a filter

is at end of life, at

least within the

SMART mode, it will

discourage usage till

the filter is replaced,

by limiting the fan

speed so as not to

reintroduce the

captured particulate

matter back into the

air.

4

The air purifier

produces a loud or

abnormal noise

Please ensure the air inlet (around front panel) and

air outlet grill (top of the unit) are unobstructed and

that there is a clearance of at least 30 cm between

these areas and the nearest surface. If using a custom

fabric cover, try to reapply the fabric cover to the

panel tighter OR try operating without it to see if

noise pattern becomes normal.

If neither of the above steps OR instructions in the

Wellbeing App help, please refer to item 9 in the

table.

An abnormal pattern

of noise OR an

unusually high pitch

is not by design,

hence it is best to

rectify this.

5

The air purifier or

fan does not

operate

Ensure that the house, wall socket being used, and

the unit are all receiving power. If needed, try

pushing the power plug firmly into the wall socket to

check if this resolves the issue.

If you have recently (re)placed a filter please remove

and reinsert it. Check to make sure that the filter is

oriented correctly, so the RFID sensor can detect it.

If neither of the above steps OR instructions in the

Wellbeing App help, please refer to item 9 in the

table.

As a safety

mechanism, to avoid

risk of injury from

the fan blade, the

unit will not operate

if it does not detect

the presence of

filter(s).

www.electrolux.com

18

6

The air purifier is

running but the air

quality does not

improve

If in SMART mode, closely monitor the difference in

air quality levels within the Wellbeing App for next 20

minutes – if you do not see any improvement of the

air quality values in the Wellbeing App during this

period then follow the step below.

Change to MANUAL mode and adjust the fan speed

to a higher level to see if this helps resolve the issue.

If you still do not see any improvement, please try the

step below.

Try and close any open doors OR windows to the

outside of the room and rerun the unit at the highest

fan speed for 20 minutes. If this resolves the issue,

we recommend that you operate the unit in this

sealed environment as much as possible, till the air

quality outside (or in other rooms) is also at a good

level.

If the unit is placed in

a room larger t h a n

the recommended

size, it will take longer

for the air quality to

improve – please be

patient and maintain

the unit at the highest

speed feasible.

The unit comes with

multiple filters –

please ensure you

have the appropriate

filters to tackle the

pollutant you seek to

remove.

7

The air purifier

produces or emits

a strange smell

The first time you run the unit, you may perceive a

plastic, glue or paint smell – especially near the air

outlet grill – this is unavoidable in some cases (like

the ‘new car smell’) but should disappear quickly.

If you perceive a burning smell, please disconnect the

unit and contact Electrolux authorized service center

for further support.

Always ensure that

the filters are

covered in

appropriate

packaging while

stored away

between uses.

8

I am unable to

onboard the air

purifier to the App

If you are unable to onboard the unit and connect it

to the Wellbeing App after a couple of attempts

following the steps in the Wellbeing App and FAQ,

then the best course of action is to contact an

Electrolux authorized service center for support.

The WiFi chip in the

unit operates only at

2.4Ghz so please

ensure your home

WiFi is operating at

this bandwidth.

9

I have another

issue not listed

here OR none of

the above steps

have helped

resolve the

issue

You can search for more troubleshooting and FAQ

guides on our website OR the Wellbeing App under

the product information pages, or directly contact

Electrolux authorized service center for support.

Thank you!

Please have at hand

the unit’s PNC and

SERIAL number.

19

www.electrolux.com

NÁVOD K OBSLUZE

Děkujeme, že jste si zvolili čističku vzduchu řady Electrolux WELL A7/A5. Aby vaše

zařízení pracovalo co nejlépe, používejte vždy originální spotřební materiál,

příslušenství a náhradní díly Electrolux. Spotřebič je navržen s ohledem na životní

prostředí a všechny plastové díly jsou proto recyklovatelné.

VŠEOBECNÉ BEZPEČNOSTNÍ INFORMACE

V NÁVODU K POUŽITÍ naleznete konkrétní pokyny pro provoz vašeho modelu NEBO

řady. Zařízení používejte pouze v souladu s pokyny v tomto návodu. Tyto pokyny

nemají za cíl pokrýt všechny možné podmínky a situace, které mohou nastat. Při

instalaci, provozu a údržbě jakéhokoliv spotřebiče je nutné postupovat opatrně a

řídit se zdravým rozumem.

VAROVÁNÍ! – BEZPEČNOST DĚTÍ A POSTIŽENÝCH OSOB

Hrozí nebezpečí udušení, zranění nebo trvalého postižení. Všechny obaly

uschovejte z dosahu dětí.

Tento spotřebič smí používat děti starší osmi let nebo osoby se sníženými fyzickými,

smyslovými nebo duševními schopnostmi nebo osoby bez patřičných zkušeností a

znalostí, pouze pokud tak činí pod dozorem nebo obdrželi instrukce týkající se

bezpečného provozu zařízení, a pokud rozumí rizikům spojeným s provozem

zařízení.

Čištění a uživatelskou údržbu nesmí provádět děti bez dozoru. Zabraňte dětem, aby

si se zařízením hrály. Děti mladší tří let bez stálého dozoru držte z dosahu zařízení.

UPOZORNĚNÍ! – PŘEDEJDĚTE ZRANĚNÍ NEBO POŠKOZENÍ ZAŘÍZENÍ ČI MAJETKU

Nesměrujte proud vzduchu na krby nebo jiné zdroje tepla, protože by mohlo

dojít k vyšlehnutí plamene.

Na zařízení nestoupejte ani na něj nestavte předměty.

Na zařízení nezavěšujte žádné předměty.

Na zařízení nepokládejte nádoby s kapalinami.

Nebudete-li zařízení delší dobu používat, odpojte je od napájení.

Neblokujte ani nezakrývejte oblast přívodu vzduchu, oblast ventilátoru a mřížku

výstupu vzduchu.

Ujistěte se, že jakékoliv elektrické/elektronické vybavení se nachází alespoň 30 cm od

zařízení.

GB

CS

DA

FI

FR

DE

HR

HU

IT

NO

PL

RO

SK

SL

SR

SV

TR

www.electrolux.com

20

La page est en cours de chargement...

Electrolux WA71-305DG Manuel utilisateur

Electrolux WA71-305DG Manuel utilisateur

dans d''autres langues

Autres documents