Modern Forms WS-21724-CH Guide d'installation

Modern Forms
Marque
Modern Forms
Modèle
WS-21724-CH
Taper
Guide d'installation

Ce manuel convient également à

1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21724 / WS-21736
Wire Connector
Qty: 5 pcs + 1 Extra
7EAC112201
P3
Mounting Screw
Qty: 1 Extra
7MPF0409S3
5/32 - 32x3/8
Nickel Plating
Junction Box Screw
Qty: 2 pcs + 1 Extra
7MPF0415C2
#8 - 32x5/8 SS
Mounting Ring
Qty: 1 pc
7MBC101501
Conversion Plate
Qty: 1 pc
4MBC171111CH
4MBC171111BN1
4MBC201105CH
4MBC201105BN1
Assembly Screw
Qty: 2 pcs + 1 Extra
7MPF0808C1
#8 - 32x3/8 SS
Driver
Qty: 1 pc
4LD-700MA28U-IS-P
A1 B1 C1 D1 E1 F1 G1
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21724 / WS-21736
FIG. 1 MOUNT ON SWITCH BOX
FIG. 2 MOUNT ON JUNCTION BOX
FIG. 3
Ø
4
Mounting Screw
Driver
Wire Connector
Assembly Screw
Conversion Plate
Junction Box Screw
Mounting Ring
Mounting Screw
Fixture Back Plate
Adjustable Nut
Wire
Driver
Junction Box
Mounting Plate
Switch Box
Ground Wire
Back Plate Dimensions
Mounting Plate Dimensions
Fixture
Mounting Plate
Junctinon Box Screw
Adjustable Nut
C1
B1
G1
A1
F1
E1
C1
D1
B1
G1
G
N
D
5 7/8"
2 1/2"
1 3/8"
1 5/8"
1 3/8"
1 3/4"
3Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
217 - LED Wall Sconce
WS-21724 / WS-21736
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
INSTALLATION
MOUNT ON SWITCH BOX (Fig. 1)
3. Remove the mounting screws (B1) from the xture.
4. Connect the driver (G1) input wire to switch box wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire, connect the xture's ground wire to it. Otherwise, connect the xture's ground
wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
*Requires Driver to be recessed within the switch box.
5. Secure the mounting plate to the switch box using the junction box screws (C1). The side of the mounting plate marked
"GND" must face out.
6. The back plate location for this xture is adjustable.
First, loosen both adjustable nuts by turning counterclockwise.
Second, adjust the back plate to your desired location.
Third, pull and tighten the electrical wire.
Lastly, secure the back plate by turning both adjustable nuts clockwise.
7. Place the xture over the mounting plate, and secure it with mounting screws (B1).
OR
MOUNT ON JUNCTION BOX (Fig. 2)
3. Remove the mounting screws (B1) from the xture.
4. Connect the driver (G1) input wire to junction box wires as shown in Fig. 3, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire, connect the xture's ground wire to it. Otherwise, connect the xture's ground
wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
*Requires Driver to be recessed within the junction box.
5. Secure the mounting ring (D1) to the switch box using the junction box screws (C1). Make sure the two holes (Spacing 2-3/4") are horizontal
as shown in Fig. 2. The side of the mounting plate marked "GND" must face out.
6. Secure the mounting plate and conversion plate (E1) to the mounting ring with assembly screw (F1).
7. The back plate location for this xture is adjustable.
First, loosen both adjustable nuts by turning counterclockwise.
Second, adjust the back plate to your desired location.
Third, pull and tighten the electrical wire.
Lastly, secure the back plate by turning both adjustable nuts clockwise.
8. Place the xture over the mounting plate, and secure it with mounting screws (B1).
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 4 Wiring
  • Page 1 1
  • Page 2 2
  • Page 3 3

Modern Forms WS-21724-CH Guide d'installation

Modern Forms
Marque
Modern Forms
Modèle
WS-21724-CH
Taper
Guide d'installation
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents