DMP 1102 Series Wireless Universal Transmitter Guide d'installation

Marque: DMP

Modèle: 1102 Series Wireless Universal Transmitter

Taper: Guide d'installation

Ce manuel convient également à

1101 Series

1101 SERIES WIRELESS

UNIVERSAL TRANSMITTER

Installation Guide

DESCRIPTION

The 1101Series Wireless Universal

Transmitters are two‑way

supervisory wireless transmitters

typically used for door and window

applications. The 1101E features

128‑bit AES encryption.

The transmitter provides a cover

tamper, magnetic reed switch,

and an onboard terminal block to

allow for external contact wiring.

Both sets of contacts, internal and

external, can be programmed to

operate at the same time. This

allows two independent zones to

operate from one 1101.

The 1101Series also features

Disarm/Disable functionality. When

this option is enabled, Zone Tripped

messages are disabled when the

system is disarmed.

Compatibility

All DMP XT Series and XR Series and

all 1100 Series Wireless Receivers.

To enable encryption on 1101E models,

Version 183 is required for XT and XR

Series panels. Version 300 is required

for wireless receivers.

What is Included?

• One 1101 Wireless Universal

Transmitter

• One Magnet with Standard and

Commercial Housing

• One 3.0 V lithium CR123A battery

• Hardware pack

PROGRAM THE PANEL

Refer to the panel programming guide as needed. After completing

each of the following steps, press CMD to advance to the next

prompt.

1. At a keypad, enter 6653 (PROG) to access the Programmer

Menu.

2. (1101E only) Go to SYSTEM OPTIONS. At 1100ENCRYPTION,

select ALL to only add encrypted wireless devices to

the system. Select BOTH to allow both encrypted and

non‑encrypted wireless devices to be programmed.

3. (1101E only) The default passphrase appears at the ENTER

PASSPHRASE prompt. Press CMD to keep the default. Press

any select key or area to change the passphrase and enter

an 8‑character hexadecimal string (0‑9, A‑F).

4. At ZONE INFORMATION, enter the wireless zone number.

5. At *UNUSED*, enter the zone name.

6. At ZONE TYPE, press any select key or area and select the

zone type.

7. At the NEXT ZN? prompt, select NO.

8. When WIRELESS? displays, select YES.

9. At SERIAL#, enter the eight‑digit device serial number.

10. At CONTACT, select either INTERNAL or EXTERNAL.

Note: Use consecutive zone numbers if using both

internal and external contacts.

11. At SUPRVSN TIME, enter a supervision time. Default is 240.

12. At DISARM DISABLE, select NO or YES.

Note: Program the external contact ﬁrst if using both

internal and external contacts with Disarm/Disable

functionality.

13. At the NEXT ZONE prompt, select YES if you are ﬁnished

programming the zone. Select NO if you would like to access

additional programming options.

14. To save panel programming, go to STOP and press CMD.

INSTALL THE BATTERY

Use a 3.0V lithium battery, a DMP Model CR123A battery, or an

equivalent model from Sony or Murata. For listed installations,

use either an Energizer® 123battery or a CR123A battery

manufactured by Panasonic or Tekcell.

1. Push the button on the end of the 1101and separate the

two halves.

2. Observing polarity, place the battery in the holder and

press it into place. Refer to Figure 2during installation.

Figure 1: 1101 Wireless Transmitter

2 1101 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

MOUNT THE TRANSMITTER

Mount the Housing

When mounting the transmitter, refer to Figure 2for battery and

mounting hole location.

1. Remove the battery.

2. Place the supplied #4screw into the mounting hole and

secure the transmitter housing to the surface.

3. Reinsert the battery.

4. Snap the transmitter cover back onto the base.

Mount the Magnet

For magnet placement options, refer to Figure 5.

Standard Installation

1. Push the supplied magnet into the magnet cover.

2. Hold the magnet base on the door closest to the magnetic

reed switch, no more than 1/2” (1.3cm) from the transmitter.

3. Use the provided #4 screws to mount the base. See Figure 3.

4. Snap the cover onto the base.

Commercial Installation

1. Push the supplied magnet into the magnet cover.

2. Place and hold the magnet cover directly on the door closest

to the magnetic reed switch, no more than 1/2” (1.3cm) apart

from the transmitter.

3. Use the provided #4screws to mount the cover. See

Figure 4.

The 1101 provides a Survey LED capability to allow one person to conﬁrm communication with the wireless

receiver or panel while the cover is removed.

1. With the cover removed, hold the transmitter in the desired location.

2. Press the tamper switch to send data to the panel and determine if communication is conﬁrmed or

faulty.

Conﬁrmed: If communication is conﬁrmed, for each press or release of the tamper switch, the LED

blinks immediately on and immediately o.

Faulty: If communication is faulty, the LED remains on for about 8 seconds or ﬂashes multiple times

in quick succession. Relocate the transmitter or receiver until the LED conﬁrms clear communication.

SELECT A LOCATION

Figure 2: Transmitter Components

Survey

LED

Mounting

Hole

Magnetic Reed

Switches

Figure 3: Standard Installation

Figure 4: Commercial Installation

PLACEMENT OPTIONS

Figure 5: Placement Options

1101 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

TEST THE TRANSMITTER

After the transmitterhas been installed, test to conﬁrm that it is communicating reliably with the panel. Use

the Tech APP™ to perform a Wireless Walk Test on the system or complete the following steps to perform a

Walk Test from a keypad that is connected to the panel:

At the keypad, enter 8144 (WALK) and select WLS. If the transmitter fails to check in at the keypad,

ensure that it is wired properly and check for sources of interference such as metal objects and electronic

equipment.

ADDITIONAL INFORMATION

Supervision Time

When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset. If the

receiver has been powered down for more than one hour, wireless transmitters may take up to an additional hour to send

a supervision message unless tripped, tampered, or powered up. This operation extends battery life for transmitters. A

missing message may display on the keypad until the transmitter sends a supervision message.

Replace the Battery

1. Push the button on the end of the transmitterand separate the two halves.

2. Remove the old battery, observe polarity, and place the new battery in the holder.

3. Snap the cover back on the transmitter.

Sensor Reset to Clear LOBAT

Once the battery is replaced, a sensor reset is required at the keypad to clear the LOBAT message. On an LCD keypad,

press and hold 2for two seconds. On a graphic touchscreen keypad, press RESET. Enter your user code, if required. The

keypad displays SENSORS OFF followed by SENSORS ON.

EXTERNAL CONTACTS

Figure 6: Connect External Contact

External Contact

Terminal Block

1101

Door

Window

External

Contact

Magnet

Program an internal

contact as the next

consecutive zone.

Program an

external contact as

the ﬁrst zone.

WIRE EXTERNAL CONTACTS (OPTIONAL)

Refer to Zone Information in the appropriate panel programming guide for more information. DMP

recommends using 18or 22AWG unshielded wire for contact connections. Do not use twisted pair or shielded

wire. Refer to Figure 6 when wiring external contacts.

1. Use a ﬂathead screwdriver to loosen the two external contact terminal screws.

2. Insert external contact wiring into the 1101terminal block and tighten the screws.

3. Connect the other ends of the wires to the external contact as either normally open (N/O) or normally

closed (N/C) without an end‑of‑line resistor.

4. Snap the transmitter cover back onto the base.

Designed, engineered, and

manufactured in Springﬁeld, MO

using U.S. and global components.

LT-0694 1.04 20023

1101 SERIES UNIVERSAL

WIRELESS TRANSMITTER

Speciﬁcations

Battery

Life Expectancy 5 Years (normal operation)

Type 3.0V lithium CR123A Frequency

Range 905-924 MHz

Dimensions

Transmitter Case 3.3” L x 1.6” W x 0.9” H

Transmitter Base 3.3” L x 1.6” W x 0.1” H

Magnet Housing 1.5” L x 0.5” W x 0.7” H

Magnet Spacer 1.5” L x 0.5” W x 0.1” H

Housing Material Flame-retardant ABS

Ordering Information

1101-W Standard Wireless Universal Transmitter

1101E-W Encrypted Wireless Universal Transmitter

Patents

U. S. Patent No. 7,239,236

Certiﬁcations

FCC Part 15 Registration ID CCKPC0191

Industry Canada Registration ID 5251A-PC0191

Underwriters Laboratory (UL) Listed

ANSI/UL 1023 Household Burglar Alarm System

Units Accessory Magnetically Activated

Switch or Door Contact Transmitter

ANSI/UL 634 Connections and Switches for use with

Burglar Alarm Systems Accessory

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from

all persons. It must not be located or operated in conjunction with any other antenna or transmitter.

Changes or modiﬁcations made by the user and not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA INFORMATION

This device complies with Industry Canada Licence‑exempt RSS standards. Operation is subject to the following two

conditions:

1. This device may not cause interference, and

2. this device must accept any interference, including interference that may cause undesired operation of the device.

This system has been evaluated for RF Exposure per RSS‑102 and is in compliance with the limits speciﬁed by Health

Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general

bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

1. l’appareil ne doit pas produire de brouillage, et

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites

établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces

(20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand

public.

DMP 1102 Series Wireless Universal Transmitter Guide d'installation

Marque: DMP

Modèle: 1102 Series Wireless Universal Transmitter

Taper: Guide d'installation

Ce manuel convient également à

1101 Series

Télécharger le PDF

rapport

dans d''autres langues

English: DMP 1102 Series Wireless Universal Transmitter Installation guide

DMP 1102 Series Wireless Universal Transmitter Guide d'installation

Ce manuel convient également à

DMP 1102 Series Wireless Universal Transmitter Guide d'installation

dans d''autres langues

Documents connexes

Autres documents