Rockford Fosgate PUNCH 400 Manuel utilisateur

p

owe

r

®

2-channel

trans•

ana

trans•

ana

trans•

ana

trans•

nova

4-channel

2-channel

trans•

ana

4-channel

trans•

ana

Power AMPLIFIER

INSTALLATION & OPERATION

® ®

car audio

fanatics

for

POWER 360 POWER 400 POWER 500 POWER 800 POWER 800 POWER 1000

2-channel 4-channel 2-channel 2-channel 4-channel 2-channel

Dynamic Power Rating

(IHF-202 Standard) - Measured at 14.4 Volts

Mono into a 4Ω Load

481 Watts x 1 232 Watts x 2 710 Watts x 1 960 Watts x 1 525 Watts x 2 1460 Watts x 1

Per channel into a 2Ω Load

242 Watts x 2 127 Watts x 4 330 Watts x 2 480 Watts x 2 270 Watts x 4 730 Watts x 2

Per channel into a 4Ω Load

154 Watts x 2 84 Watts x 4 210 Watts x 2 240 Watts x 2 150 Watts x 4 450 Watts x 2

Continuous Power Rating

(Competition Standard) - Measured at 13.8 Battery Volts

RMS continuous power per channel,

90 Watts x 2 50 Watts x 4 125 Watts x 2 200 Watts x 2 100 Watts x 4 250 Watts x 2

both channels driven into a 4Ω load

from 20 to 20,000 Hz with less than

0.05% Total Harmonic Distortion (THD)

RMS continuous power per channel,

180 Watts x 2 100 Watts x 4 250 Watts x 2 400 Watts x 2 200 Watts x 4 500 Watts x 2

both channels driven into a 2Ω load

from 20 to 20,000 Hz, with less than

0.1% Total Harmonic Distortion (THD)

RMS continuous power mono into a

360 Watts x 1 200 Watts x 2 500 Watts x 1 800 Watts x 1 400 Watts x 2 1000 Watts x 1

4Ω load from 20 to 20,000 Hz, with

less than 0.1% Total Harmonic Distortion (THD)

Signal-to-Noise Ratio (A-weighted) >100dB >100dB >100dB >100dB >100dB >100dB

Crossover Slope (Butterworth) 24dB/octave 24dB/octave 24dB/octave 24dB/octave 24dB/octave 24dB/octave

Crossover Frequency

50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz 50Hz – 210Hz

Specifications are subject to change without notice.

S

PECIFICATIONS

– i –

POWER 360 POWER 400 POWER 500 POWER 800 POWER 800 POWER 1000

2-channel 4-channel 2-channel 2-channel 4-channel 2-channel

Dimensions (end caps installed)

2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H 2.62" (6.65cm) H

9.60" (24.38cm) W

9.60" (24.38cm) W 9.60" (24.38cm) W 9.60" (24.38cm) W 9.60" (24.38cm) W

12.27" (31.16cm) L 13.27" (33.70cm) L 13.27" (33.70cm) L 18.27" (46.40cm) L 18.27" (46.40cm) L

18.27" (46.40cm) L

Heatsink Type (internal use only) #3 #4 #4 #6 #6 #6

Frequency Response (±0.5dB) 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz 20Hz - 20kHz

Bandwidth (±3dB) 20Hz - 200kHz 20Hz - 200kHz 20Hz - 200kHz 20Hz

- 200kHz 20Hz - 200kHz 20Hz - 200kHz

Damping Factor @ 4Ω (at output connector) >200 >200 >200 >200 >200 >200

Slew Rate 30 Volts/ µs 30 Volts/ µs 30 Volts/ µs 30 Volts/ µs 30 Volts/ µs 30 Volts/ µs

IM Distortion (IHF) <0.05% <0.05% <0.05% <0.05% <0.05% <0.05%

Source Unit Compatibility (+15dB gain overlap)

17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA) 17V max. (RCA)

Input Sensitivity (+0dB gain overlap) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA) 250mV~

4V (RCA) 250mV~4V (RCA) 250mV~4V (RCA)

Protection NOMAD - Internal analog-computer output protection circuitry limits power in case of

overload. Thermal switch shuts down the amplifier in case of overheating.

Battery Fuse Rating (External to Amplifier) 40A 50A 50A 60A* 60A* 2-50A or 1-100A*

Fuse Type ATC AGU AGU AGU AGU 2-AGU OR 1- ANL

Equalization (45Hz Punch Bass) Variable Rear Variable Variable Variable Rear Variable Variable

(0 to +18dB) (0 to +18dB) (0 to +18dB) (0 to +18dB) (0 to +18dB) (0 to +18dB)

Input Impedance 20k ohms 20k ohms 20k ohms 20k ohms 20k ohms 20k ohms

* recommended fuse not supplied with amplifier

Specifications are subject to change without notice.

– ii –

Dear Customer,

Congratulations on your purchase of the world's finest brand of car audio amplifiers.

At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are

pleased you chose our product. Through years of engineering expertise, hand craftsman-

ship and critical testing procedures, we have created a wide range of products that

reproduce music with all the clarity and richness you deserve.

For maximum performance we recommend you have your new Rockford Fosgate

product installed by an Authorized Rockford Fosgate Dealer, as we provide specialized

training through Rockford Technical Training Institute (RTTI). Please read your

warranty and retain your receipt and original carton for possible future use.

Great product and competent installations are only a piece of the puzzle when it comes

to your system. Make sure that your installer is using 100% authentic installation

accessories from Connecting Punch in your installation. Connecting Punch has

everything from RCA cables and speaker wire to Power line and battery connectors.

Insist on it! After all, your new system deserves nothing but the best.

To add the finishing touch to your new Rockford Fosgate image order your Rockford

wearables, which include everything from T-shirts and jackets to hats and sunglasses.

To get a free brochure on Rockford Fosgate products and Rockford accessories, in the

U.S. call 480-967-3565 or FAX 480-967-8132. For all other countries, call +001-480-

967-3565 or FAX +001-480-967-8132.

If, after reading your manual, you still have questions regarding this product,

we recommend that you see your Rockford Fosgate dealer. If you need further

assistance, you can call us direct at 1-800-669-9899. Be sure to have your serial

number, model number and date of purchase available when you call.

PRACTICE SAFE SOUND™

CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 100dB

MAY

CAUSE PERMANENT HEARING LOSS. HIGH POWERED AUTOSOUND

SYSTEMS

MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER

130dB. USE COMMON SENSE AND PRACTICE SAFE SOUND.

The serial number can be found on the outside of the box. Please record it in

the space provided below as your permanent record. This will serve as

verification of your factory warranty and may become useful in recovering your

amplifier if it is ever stolen.

Serial Number: ________________________________

Model Number:________________________________

– iii –

T

ABLE

OF

C

ONTENTS

Specifications.............................................................................................. i

Introduction................................................................................................1

Power Amplifier Accessory Pack ................................................................... 1

Feature Chart..............................................................................................2

Design Features .......................................................................................... 3

Installation Considerations ........................................................................... 7

Mounting Location ...................................................................................... 8

Battery and Charging ..................................................................................9

Wiring the System.......................................................................................9

Using Passive Crossovers...........................................................................11

Table of Component Values........................................................................ 12

Installation ............................................................................................... 13

Operation................................................................................................. 21

System Diagrams...................................................................................... 24

Troubleshooting........................................................................................28

Dynamic Power Measurements................................................................... 31

Warranty Information ................................................................................ 33

International Information............................................................................34

Sections marked

ADVANCED OPERATION

include in-depth

technical information

Sections marked

TROUBLESHOOTING

include recommendations for

curing installation problems

Sections marked

INSTALLATION

include “slam dunk”

wiring connections

I

N

S

T

A

L

A

T

I

O

N

+ -

TROUBLE-

S

H

O

T

I

N

G

?

Welcome to Rockford Fosgate! This manual is designed to provide information

for the owner, salesperson and installer. For those of you who want quick

information on how to install this product, please turn to the

Installation

Section

of this manual or refer to the icons listed below. Other information can

be located by using the Table of Contents. We, at Rockford Fosgate, have

worked very hard to make sure all the information in this manual is current. But,

as we are constantly finding new ways to improve our product, this information

is subject to change without notice.

GETTING STARTED

a

d

v

a

n

c

e

d

O

p

e

r

a

t

i

o

n

+

I

NTRODUCTION

Rockford engineers designed the Power amplifiers to provide an awesome

amount of power while delivering superior sound quality in a convenient and

efficient package. The TRANS•

ana

& patented TRANS•

nova

topologies are

low voltage circuits used in the preamp stage of the Power amplifiers that let

the music sound crystal clear and very real, even when played at high

volume levels. This is matched with TOPAZ, a unique grounding circuit used

to eliminate noise problems associated with car audio systems and their

installation. The use of a protection circuit called NOMAD, along with

MOSFET, DSM (Discrete Surface Mount) and innovative MEHSA heat

dissipating technologies improves amplifier efficiency. The result of these

components give the Power amplifier awesome sound quality in a “Bullet

Proof” package.

– 1 –

P

OWER

A

MPLIFIER

A

CCESSORY

P

ACK

The accessory pack shipped with the Power amplifiers includes the mounting

hardware necessary to secure the amp to the vehicle.

Installation & Operation Manual

Punch Verification Certificate

(4) Amplifier mounting screws (#8 x 3/4" Phillips)

(4) Speaker/Power connector set screws (3/32" Allen)

(4) Endbell mounting screws (9/64" Allen)

(1) Allen wrench (3/32")

(1) Allen wrench (9/64")

(1) Inline fuseholder (Power 360, Power 400 & Power 500 2-channel amps)

(1) AGU 40 amp fuse (Power 360 2-channel amp)

(1) AGU 50 amp fuse (Power 400 4-channel & Power 500 2-channel amps)

(1) Remote Punch Bass (replacement part #WP-2429)

(1) 15' Remote Punch Bass cable (replacement part #CC-2421)

(2) Remote Punch Bass bracket screws (4 x 7/16" Phillips)

NOTE: Refer to the specifications section for recommended fuse sizes on the

Power 800 2-channel, Power 800 4-channel & Power 1000 2-channel amps.

POWER AMPLIFIER MODEL Power Power Power Power Power Power

360 400 500 800 800 1000

# of CHANNELS 2422 42

Stable Into: (stereo/mono) 2Ω/4Ω 2Ω/4Ω 2Ω/4Ω 2Ω/4Ω 2Ω/4Ω 2Ω/4Ω

CIRCUITRY

1

TRANS•

ana

– circuit topology xxxx x–

TRANS•

nova

– patented circuit topology

2

–––– –x

DIAMOND

– patented MOSFET driver stage

3

–––– –x

Class-G – high efficiency topology –––– ––

MEHSA – heat dissipating technology xxxx xx

TOPAZ

– patented noise eliminating circuitry

4

xxxx xx

DSM – discrete surface mount xxxx xx

MOSFETs – power supply & output devices xxxx xx

NOMAD – protection circuit xxxx xx

FEATURES

Die Cast Heatsink

5

xxxx xx

Hi-Level Inputs – for factory radios –––– ––

RCA Inputs – for aftermarket radios xxxx xx

Input Switches – eliminates “Y” adaptors –x–– x–

Pass-Thru – feeds signal to aux. amp xxxx xx

Pwr/Spk Screw Terminals –––– ––

Pwr/Spk Block Terminals xxxx xx

4 Gauge PWR/GND xxxx xx

Variable Punch Bass (0dB ~+18dB @ 45Hz) Remote Remote Rear Remote Remote Remote Rear Remote

Variable Xover (50Hz ~ 210Hz) HP/FULL/LP

6

HP/FULL/LP

6

HP/FULL/LP

6

HP/FULL/LP

6

HP/FULL/LP

6

HP/FULL/ LP

6

Crossover Slope (Butterworth) 24dB 24dB 24dB 24dB 24dB 24dB

Phase Warp (0

0

~ 180

0

) –––– –x

1

Additional information on features, specifications and system designs can be found at: www.rockfordfosgate.com

2

Trans•nova is patented under "U.S. Patent No. 4,467,288"

3

DIAMOND is patented under "U.S. Patent No. 5,673,000"

4

TOPAZ is patented under "U.S. Patent No. 5,751,823"

5

Diecast Heatsink is patented under "U.S. Patent No. D401,225"

6

HP = 24dB/octave High-Pass / LP = 24dB/octave Low-Pass / FULL = Full Range

7

Recommended fuses not supplied with amplifier

– 2 –

P

OWER

A

MPLIFIER

F

EATURE

C

HART

– 3 –

D

ESIGN

F

EATURES

Power 360

2-channel

Power 400

4-channel

Speaker

+ L -

Crossover Frequency

Left Gain

Input

Pass-Thru

LR

Right

Gain

Remote

Punch Bass

HP-Full-LP

Crossover

Speaker

+ R -

65

80

55

50

110

210

Hz

145

190

REM

B+ GND

LED

5

2

9

8

77

9

2

6

1

10

3

2

6

4

5

7

1

LR+ LR- RR+ RR- B+ GND LF- LF+ RF+RF-

REM

LED

Front

Crossover

HP-Full-LP

4/2

Input

Front

Gain

Front

Crossover

Frequency

65

80

55

50

110

210

Hz

145

190

Front Pass-Thru Rear

RR

LL

Rear

Crossover

Frequency

65

80

55

50

110

210

Hz

145

190

Rear

Gain

Rear

Crossover

HP-Full-LP

Rear

Remote

Punch

Bass

9

8

7

9

10

3

2

9

– 4 –

Power 500

2-channel

Power 800

2-channel

Speaker

+ L -

Crossover Frequency

Left Gain

Input

Pass-Thru

LR

Right

Gain

Remote

Punch Bass

HP-Full-LP

Crossover

Speaker

+ R -

65

80

55

50

110

210

Hz

145

190

REM

B+ GND

LED

5

2

9

8

77

9

2

6

1

10

3

2

10

2

1

2

3

6

8 99

5

7

2

7

B+ GND

LED

REM

Speaker

+ L -

Crossover Frequency

Left Gain

Input

Pass-Thru

LR

Right

Gain

Remote

Punch Bass

HP-Full-LP

Crossover

Speaker

+ R -

65

80

55

50

110

210

Hz

145

190

– 5 –

Power 800

4-channel

1

2

6

899 774

5

9 9

3

10

2 2

LED

LR+ LR- RR+ RR- B+ GND LF- LF+ RF+RF-

REM

Front

Crossover

HP-Full-LP

4/2

Input

Front

Gain

Front

Crossover

Frequency

65

80

55

50

110

210

Hz

145

190

Front Pass-Thru Rear

RR

LL

Rear

Crossover

Frequency

65

80

55

50

110

210

Hz

145

190

Rear

Gain

Rear

Crossover

HP-Full-LP

Rear

Remote

Punch

Bass

Power 1000

2-channel

2

1

2

8 99

5

7

2

7

3

6

10

11

65

80

55

50

110

210

Hz

145

190

HP–Full–LP

Crossover

Input

Pass-Thru

LR

Crossover

Frequency

Speaker

+ L -

Speaker

+ R -

Right

Gain

Left

Gain

Remote

Punch Bass

Phase

Warp

B+ GND

LED

REM

– 6 –

1. Cast Aluminum Heatsink – The cast aluminum heatsink of the Power

amplifier dissipates heat generated by the amplifier's circuitry. The inherent

advantage of casting provides a 30% improvement of cooling over conven-

tional extrusion heatsink designs.

2. Speaker/Power Terminals – The heavy duty, gold-plated terminal block

connectors (+ and –) will accept 4 gauge cable and are immune to corrosion

that can cause signal degradation.

3. REM Terminal – This spade terminal is used to remotely turn on and turn off

the amplifier when +12V DC is applied.

4. Signal Input Switch (Power 400 & Power 800 4-channel amplifiers) – This

switch allows the amplifier to be driven with either 2 or 4 pairs of inputs.

5. RCA Input Jacks – The industry standard RCA jacks provide an easy

connection for signal level input. They are gold-plated to resist the signal

degradation caused by corrosion.

6. RCA Pass-Thru Jacks – The Pass-Thru provides a convenient source for

daisy-chaining an additional amplifier without running an extra set of RCA

cables from the front of the vehicle to the rear amplifier location.

7. Gain Control – The input gain control is preset to match the output of most

source units. It can be adjusted to match output levels from a variety of source

units.

8. Remote Punch Bass – The Punch Bass helps correct for acoustical

deficiencies in the listening environment by helping reproduce full range

sound without adding excessive boost. The Punch Bass control is a narrow

band adjustment centered at 45Hz variable from 0dB to +18dB. Connection

is made with a cable using RJ-45 and can be installed under the dash for

remote control access.

9. Internal Crossover – The internal crossover is a 24dB/octave Butterworth

filter selectable for High-Pass (HP), Full Range (FULL), or Low-Pass (LP)

operation variable from 50Hz to 210Hz.

10. LED Power Indicator – The LED illuminates when the unit is turned on.

11. Phase Warp (Power 1000 2-channel amplifier) – The phase warp is a

variable control used to adjust the phase of the output signal relative to the

phase of the input signal. The phase warp is most noticable when the system

is playing a sine wave (test tone). When used with the proper test equipment,

this feature can increase the relative SPL in a system.

I

NSTALLATION

C

ONSIDERATIONS

The following is a list of tools you will need for installing the Power amplifier:

Voltmeter Wire strippers

Electric hand drill w/assorted bits Battery post wrench

17' (5 m) Red Power Wire Wire cutters

12' (4 m) Remote Turn-On Wire Assorted connectors

1.5' (45 cm) Black Grounding Wire Wire crimpers

– 7 –

This section focuses on some of the vehicle considerations for installing your

new Power amplifier. Checking your battery and present sound system, as

well as pre-planning your system layout and best wiring routes, will save

installation time. When deciding how to lay out your new system, be sure that

each component will be easily accessible for making adjustments.

Before beginning any installation, be sure to follow these simple rules:

1. Be sure to carefully read and understand the instructions before attempt-

ing to install the amplifier.

2. For safety, disconnect the negative lead from the battery prior to

beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting your

amplifier in place.

4. Route all of the RCA cables close together and away from any high

current wires.

5. Use high quality connectors for a reliable installation and to minimize

signal or power loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel

lines, brake or hydraulic lines, vacuum lines or electrical wiring when

working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the

vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber or plastic

grommets to protect any wires routed through metal, especially the

firewall.

9. ALWAYS protect the battery and electrical system from damage with

proper fusing. Install a fuseholder and appropriate fuse on the +12V

power wire within 18” (45 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the

metal to ensure a good, clean ground connection. Grounding connec-

tions should be as short as possible and always be connected to metal

that is welded to the main body, or chassis, of the vehicle.

M

OUNTING

L

OCATION

The mounting location and position of your amplifier will have a great effect

on its ability to dissipate the heat generated during normal operation. The

design of our cast aluminum heatsink serves to easily dissipate the heat

generated over a wide range of operating conditions. However, to maximize

the performance of your amplifier, care should be taken to ensure adequate

ventilation.

Trunk Mounting

Mounting the amplifier vertically on a surface with the fin grooves running

up and down will provide the best cooling of the amplifier.

Mounting the amplifier on the floor of the trunk will work but provides less

cooling capability than vertical mounting.

Mounting the amplifier upside down to the rear deck of the trunk will not

provide proper cooling and will severely affect the performance of the

amplifier and is strongly

not

recommended.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as long as

you provide a sufficient amount of air for the amplifier to cool itself. If you

are going to mount the amplifier under the seat of the vehicle, you must have

at least 1" (2.54cm) of air gap around the amplifier's heatsink.

Mounting the amplifier with less than 1" (2.54cm) of air gap around the

amplifier's heatsink in the passenger compartment will not provide proper

cooling and will severely affect the performance of the amplifier and is

strongly

not

recommended.

Engine Compartment Mounting

Rockford Fosgate amplifiers should

never

be mounted in the engine

compartment. Not only will this void your warranty but could create an

embarrassing situation caused by the ridicule from your friends.

– 8 –

B

ATTERY

AND

C

HARGING

– 9 –

Amplifiers will put an increased load on the vehicle's battery and charging

system. We recommend checking your alternator and battery condition to

ensure that the electrical system has enough capacity to handle the

increased load of your stereo system. Stock electrical systems which are in

good condition should be able to handle the extra load of any Rockford

amplifier without problems, although battery and alternator life can be

reduced slightly. To maximize the performance of your Rockford Fosgate

amplifier, we suggest the use of a heavy duty battery and an energy storage

capacitor.

W

IRING

THE

S

YSTEM

CAUTION: Avoid running power wires near the low level input cables,

antenna, power leads, sensitive equipment or harnesses. The power wires

carry substantial current and could induce noise into the audio system.

1. Plan the wire routing. Take care when running signal level RCA cables

to keep them close together but isolated from the amplifier's power

cables and any high power auto accessories, especially electric

motors. This is done to prevent coupling the noise from radiated

electrical fields into the audio signal. When feeding the wires through

the firewall or any metal barrier, protect them with plastic or rubber

grommets to prevent short circuits. Leave the wires long at this point

to adjust for a precise fit at a later time.

2. Prepare the Power cable for attach-

ment to the amplifier by stripping

5/8" of insulation from the end of

the wire. The use of 8 gauge power

cable can interfere with the installa-

tion of the end caps. Proper wire

dress can prevent this from occur-

ring. To prevent the wire from fray-

ing, strip the insulation at a 45°

angle. Insert the bared wire into the B+ terminal with the long side of

the insulation on the top. Bend the cable down at a 90° angle. Tighten

the set screw to secure the cable in place.

3. Strip 3/8" from the battery end of the power cable and crimp a large

ring terminal to the cable. Use the ring terminal to connect to the

battery positive terminal. Do not install the fuse at this time.

><

5/8"

INSULATION

STRIP WIRE

>

AMP

>

– 10 –

4. Prepare a length of cable to be used for the ground connection. Strip

5/8" of insulation from the end of the cable as described above and

connect to the appropriate terminal of the amplifier. Prepare the chassis

ground by scraping any paint from the metal surface and thoroughly

clean the area of all dirt and grease. Strip the other end of the wire and

attach a ring connector. Fasten the cable to the chassis using a non-

anodized screw and a star washer.

5. Prepare the REM turn-on wire for connection to the amplifier by stripping

1/4" of insulation from the wire end and crimping an insulated spade

connector in place. Slide the connector over the REM terminal on the

amplifier. Connect the other end of the REM wire to a switched 12 volt

positive source. The switched signal is usually taken from the source

unit's auto antenna or the accessory lead. If the source unit does not

have these outputs available, the recommended solution is to wire a

mechanical switch in line with a 12 volt source to activate the amplifier.

6. Securely mount the amplifier (with supplied screws) to the vehicle or

amp rack. Be careful not to mount the amplifier on cardboard or plastic

panels. Doing so may enable the screws to pull out from the panel due

to road vibrations or sudden vehicle stops.

7. Determine the number of inputs needed to drive the amplifier and move

the input switch to the desired setting (Power 400 & Power 800 4-

channel amplifiers only.).

8. Connect the source signal to the amplifier by plugging the RCA cables

into the input jack(s) at the amplifier.

9. Connect the speakers. Strip the speaker wires 5/8" and insert into the

appropriate terminal on the amplifier. Insert the bared wire into the

speaker terminal and tighten the set screw to secure into place. Be sure

to maintain proper speaker polarity.

DO NOT chassis ground any of the

speaker leads as unstable operation may result.

10. Perform a final check of the completed system wiring to ensure that all

connections are accurate. Check all power and ground connections for

frayed wires and loose connections which could cause problems from

road vibrations.

– 11 –

U

SING

P

ASSIVE

C

ROSSOVERS

A passive crossover is a circuit that uses capacitors and/or coils and is placed

on speaker leads between the amplifier and speaker. The crossover delegates

a specific range of frequencies to the speaker for optimum driver performance.

A crossover network can perform one of three functions: High-Pass (capaci-

tors), Low-Pass (inductors or coils) and Bandpass (combination of capacitor

and coil).

The most commonly used passive crossover networks are 6dB/octave

systems. These are easy to construct and require one component per filter.

Placing this filter in series with the circuit will reduce power to the speaker by

6dB/octave above or below the crossover point depending on whether it is a

high-pass or low-pass filter. More complex systems such as 12dB/octave or

18dB/octave can cause impedance problems if not professionally designed.

Passive crossovers are directly dependent upon the speaker's impedance and

component value for accuracy. When passive crossover components are

used in multiple speaker systems, the crossover's effect on the overall

impedance should be taken into consideration along with the speaker's

impedance when determining amplifier loads.

CAUTION: The Power ampli-

fiers are not recommended for impedance loads below 2Ω stereo and 4Ω

bridged (mono) loads.

a

d

v

a

n

c

e

d

O

p

e

r

a

t

i

o

n

+

– 12 –

T

ABLE

OF

C

ROSSOVER

C

OMPONENT

V

ALUES

6dB/Octave Low-Pass

6dB/Octave High-Pass

Freq.

Hertz

Speaker Impedance

80 4.1mH 1000µF 8.2mH 500µF 16mH 250µF

100 3.1mH 800µF 6.2mH 400µF 12mH 200µF

130 2.4mH 600µF 4.7mH 300µF 10mH 150µF

200 1.6mH 400µF 3.3mH 200µF 6.8mH 100µF

260 1.2mH 300µF 2.4mH 150µF 4.7mH 75µF

400 .8mH 200µF 1.6mH 100µF 3.3mH 50µF

600 .5mH 136µF 1.0mH 68µF 2.0mH 33µF

800 .41mH 100µF .82mH 50µF 1.6mH 26µF

1000 .31mH 78µF .62mH 39µF 1.2mH 20µF

1200 .25mH 66µF .51mH 33µF 1.0mH 16µF

1800 .16mH 44µF .33mH 22µF .68mH 10µF

4000 .08mH 20µF .16mH 10µF .33mH 5µF

6000 51µH14µF .10mH 6.8µF .20mH 3.3µF

9000 34µH 9.5µF68µH 4.7µF .15mH 2.2µF

12000 25µH 6.6µF51µH 3.3µF 100µH 1.6µF

2 OHMS

8 OHMS

4 OHMS

L

C L

C

L C

L

C

L = Low-Pass (Inductor)

C = High-Pass (Capacitor)

For more information, see your Authorized Rockford Fosgate Dealer.

a

d

v

a

n

c

e

d

O

p

e

r

a

t

i

o

n

+

INSTALLATION

POWER 360 2-CHANNEL

POWER 500 2-CHANNEL

POWER 800 2-CHANNEL

• RCA Inputs connect to both left and right channels

• Gain for left and right channels are set equally to balance the subwoofer

• Speaker Impedance should be 4Ω minimum

• Variable Crossover can be set to High-Pass (HP), Low-Pass (LP) or

Full Range (FULL)

I

N

S

T

A

L

A

T

I

O

N

+ -

– 13 –

Speaker

+ L -

Crossover Frequency

Left Gain

Input

Pass-Thru

LR

Right

Gain

Remote

Punch Bass

HP-Full-LP

Crossover

Speaker

+ R -

65

80

55

50

110

210

Hz

145

190

4Ω min.

RCA Input

+ -

Power Connections

Bridged/Mono Mode

Power 360 Power 500 Power 800

2-channel 2-channel 2-channel

Power 360 Power 500 Power 800

2-channel 2-channel 2-channel

Connect to remote

turn-on lead of

source unit

Connect to chassis

ground of vehicle*

Less than 18"

Connect to B+ of battery

with appropriate fuse

Pow

er 500 - 50A

*Keep grounds as short as possible

+ -

B+ GND

LED

REM

– 14 –

Speaker

+ L -

Crossover Frequency

Left Gain

Input

Pass-Thru

LR

Right

Gain

Remote

Punch Bass

HP-Full-LP

Crossover

Speaker

+ R -

65

80

55

50

110

210

Hz

145

190

2Ω min.

RCA Input

2Ω min.

–

+

–

+

• RCA Inputs connect to both left and right channels

• Gain for left and right channels operate independently

• Speaker Impedance for each channel should be 2Ω minimum

• Variable Crossover can be set to High-Pass (HP), Low-Pass (LP) or

Full Range (FULL)

I

N

S

T

A

L

A

T

I

O

N

+ -

2-Channel Mode

Power 360 Power 500 Power 800

2-channel 2-channel 2-channel

• RCA Inputs connect to both left and right channels

• Gain for left and right channels are set equally to balance the subwoofer

• Speaker Impedance for each stereo channel should be 2Ω minimum

• Speaker Impedance for bridged/mono channel should be 4Ω minimum

• Variable Crossover must be set for Full Range (FULL)

• Passive Crossovers must be used for proper stereo/mono operation

Speaker

+ L -

Crossover Frequency

Left Gain

Input

Pass-Thru

LR

Right

Gain

Remote

Punch Bass

HP-Full-LP

Crossover

Speaker

+ R -

65

80

55

50

110

210

Hz

145

190

2Ω min.

RCA Input

2Ω min.

–

+

–

+

4Ω min.

+ -

3-Channel Mode

Power 360 Power 500 Power 800

2-channel 2-channel 2-channel

– 15 –

INSTALLATION

POWER 400 4-CHANNEL

POWER 800 4-CHANNEL

LED

LR+ LR- RR+ RR- B+ GND LF- LF+ RF+RF-

REM

Connect to remote

turn-on lead of

source unit

Connect to chassis

ground of vehicle*

Power 400 - 40A

Power 800 - 50A

*Keep grounds as short as possible

Less than 18"

Connect to B+ of battery

with appropriate fuse

+ -

I

N

S

T

A

L

A

T

I

O

N

+ -

Power Connections Power 400 Power 800

4 -channel 4 -channel

La page charge ...

Rockford Fosgate PUNCH 400 Manuel utilisateur

Rockford Fosgate PUNCH 400 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents