Samsung DV5471AEP Le manuel du propriétaire

Gas and Electric Dryer

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service,

please register your product at

www.samsung.com/register

DV5471A*

DV5451A*

This manual is made with 100% recycled paper.

DV5471AEP-03022B-01_EN.indd 1DV5471AEP-03022B-01_EN.indd 1 2011-07-22  8:37:252011-07-22  8:37:25

2_ Features

features

1. Extra Large Capacity

Ultra drying capabilities are at your fingertips! Now you can dry extra-large loads. Our

ultralarge 7.4cu.ft(DV5471A*), 7.3cu.ft(DV5451A*) capacity dryer circulates more air through

your clothes, drying them faster, for a wrinkle-free result.

2. Steam Cycle

This cycle sprays a small amount of water into the dryer drum after several minutes of

tumbling with heat. It reduces bad odors from clothing that are difficult to remove when

washing with water, and also reduces wrinkles.

3. Sanitize Cycle

This cycle sanitizes garments by infusing high temperature heat deep into the fabric during

the drying cycle and eliminating 99.9% of certain bacteria.Use this cycle for clothing,

bedding, towels, or other items needing sanitization. The Sanitize cycle is certified by NSF

International, an independent third-party testing and certification organization.

4. Various Drying Cycles & Fuzzy Logic Algorithm

Simply turn the Jog Dial to select one of the 13(DV5471A*), 11(DV5451A*) automatic drying

cycles, including normal, heavy duty and bedding, or let the Fuzzy Logic Control measure the

degree of dampness and automatically set the drying time. Precision drying has never been

easier than with Samsung.

5. Time Saving

Our cycles are designed with you in mind. All our dryers are designed to dry your clothes in

less time... just 42 minutes! Giving you time for more important things in life.

6. Energy Saving

Samsung dryers are super energy efficient. You can dry up to 3.09 pounds of laundry with

1kWh. Also, both the large capacity and Fuzzy Logic Control save energy by automatically

drying your clothes the most efficient way.

NSF Protocol P154

Sanitization Performance of

Residential Clothes Dryers

DV5471AEP-03022B-01_EN.indd Sec9:2DV5471AEP-03022B-01_EN.indd Sec9:2 2011-07-22  8:37:322011-07-22  8:37:32

Features _3

7. Easy Reversible Door

The direction of our reversible door can be changed easily.

8. 4-way Vent (electric model only)

You can install the exhaust vent in the following four (4) positions: back, either side, bottom.

DV5471AEP-03022B-01_EN.indd Sec9:3DV5471AEP-03022B-01_EN.indd Sec9:3 2011-07-22  8:37:322011-07-22  8:37:32

4_ safety instructions

SAVE THESE INSTRUCTIONS

safety instructions

Congratulations on your new Samsung Dryer. This manual contains valuable

information on the installation, use, and care of your appliance. Please take the

time to read this manual to take full advantage of your dryer’s many benefits and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,

maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

CAUTION

To reduce the risk of fire, explosion, electric shock, or personal injury

when using your washer, follow these basic safety precautions:

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

DV5471AEP-03022B-01_EN.indd Sec11:4DV5471AEP-03022B-01_EN.indd Sec11:4 2011-07-22  8:37:322011-07-22  8:37:32

safety instructions _5

SAVE THESE INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your

appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in,

or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive

substances, as they give off vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any flammable substance, such

as vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc., or anything

containing wax or chemicals, such as mops and cleaning cloths. Flammable substances

may cause the fabric to catch fire by itself.

4. Do not store or use gasoline or other flammable vapors and liquids near this or any other

appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is

necessary when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the

drying compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with controls.

10.Do not repair or replace any part of the appliance or attempt any servicing unless

specifically recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

11.Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product.

12.Clean the lint screen before or after each load.

13.Do not use heat to dry articles containing foam rubber or similarly textured rubber-like

materials.

14.Keep area around the exhaust opening and adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

15.The interior of the appliance and exhaust duct should be cleaned periodically by

qualified service personnel.

16.Do not place items exposed to cooking oils in your dryer. Items contaminated with

cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

WARNING

DV5471AEP-03022B-01_EN.indd Sec11:5DV5471AEP-03022B-01_EN.indd Sec11:5 2011-07-22  8:37:322011-07-22  8:37:32

6_ safety instructions

SAVE THESE INSTRUCTIONS

safety instructions

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal

(foil type) duct is installed, it must be of a specific type identified by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

• To reduce the risk of severe injury or death, follow all installation instructions.

WARNING - Risk of Fire

To reduce the risk of fire or explosion:

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with

gasoline, dry cleaning solvents, or other flammable or explosive substances. They

emit vapors that could ignite or explode. Any material that has been in contact with a

cleaning solvent or flammable liquids or solids should not be placed in the dryer until all

traces of these flammable liquids or solids and their fumes have been removed.

There are many highly flammable items used in homes, such as acetone, denatured

alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,

turpentine, waxes, and wax removers

• Items containing foam rubber (may be labeled latex foam) or similarly textured rubber-

like materials must not be dried on a heat setting. Heated foam rubber materials can,

under certain circumstances, produce fire by spontaneous combustion.

What to do if you smell gas:

• Do not try to light any appliance.

• Do not turn on the appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency, or the

gas supplier.

WARNING

DV5471AEP-03022B-01_EN.indd Sec11:6DV5471AEP-03022B-01_EN.indd Sec11:6 2011-07-22  8:37:322011-07-22  8:37:32

safety instructions _7

SAVE THESE INSTRUCTIONS

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying

compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving.

Do not install or store this appliance where it will be exposed to the weather.

Do not tamper with controls.

Do not repair, replace, or attempt to service any part of the appliance unless specifi cally

instructed to in the user-repair instructions and you have the understanding and skills to

carry out the procedure.

Do not use fabric softeners or products to eliminate static unless the softener or product is

recommended for dryer use by the manufacturer of the fabric softener or product.

Clean the lint screen before or after each load.

Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service

personnel.

This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately and in accordance with local and national codes. See

installation instructions for information about grounding this appliance.

Do not sit on top of the dryer.

Ensure pockets are free from small, irregularly shaped hard objects, foreign material, etc. ie.

coins, knives, pins, etc. These objects could damage your dryer.

Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects.

Gas leaks may occur in your system, resulting in a dangerous situation.

Gas leaks may not be detected by smell alone.

Gas suppliers recommend you purchase and install a UL-approved gas detector.

Install and use in accordance with the manufacturer’s instructions.

Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking

oil. Even after being washed, these items may contain significant amounts of these oils.

Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed to

heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction

in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become

hot enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat

from escaping and can create a fire hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be

dangerous. Washing these items in hot water with extra detergent will reduce, but not

eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their

temperature. Never remove these items from the dryer hot or interrupt the drying cycle until

the items have run through the Cool Down cycle. Never pile or stack these items when they

are hot.

WARNING

DV5471AEP-03022B-01_EN.indd Sec11:7DV5471AEP-03022B-01_EN.indd Sec11:7 2011-07-22  8:37:332011-07-22  8:37:33

8_ Contents

contents

INSTALLING YOUR DRYER

9

9 Unpacking your dryer

10 Basic requirments

11 Ducting requirements

12 Important to installer

12 Location considerations

12 Alcove or closet installation

13 Mobile home installation

13 Exhausting

14 Gas requirements

14 Commonwealth of Massachusetts

installation instructions

15 Electrical requirements

15 Grounding

16 Electrical connections

17 Installation - General procedure

19 Final installation checklist

20 Connecting the inlet hose

22 Dryer Exhaust Tips

23 Door Reversal

OPERATING INSTRUCTIONS, TIPS

25

25 Overview of the control panel

28 Child lock

28 Drum Light

29 Rack Dry

30 Clean the lint filter

30 Load the dryer properly

30 Getting started

CARE AND CLEANING

31

31 Control Panel

31 Tumbler

31 Staines Steeltumbler (DV5471A*)/Powder

Coated Tumbler (DV5451A*)

31 Dryer Exterior

31 Dryer Exhaust System

SPECIAL LAUNDRY TIPS

32

32 Special laundry tips

TROUBLESHOOTING

33

33 Check these points if your dryer…

34 Information codes

APPENDIX

35

35 Fabric care chart

36 Protecting the environment

36 Declaration of conformity

36 Specifications

37 Cycle chart

DV5471AEP-03022B-01_EN.indd Sec2:8DV5471AEP-03022B-01_EN.indd Sec2:8 2011-07-22  8:37:332011-07-22  8:37:33

installing your dryer _9

installing your dryer

UNPACKING YOUR DRYER

Unpack your Dryer and inspect it for shipping damage. Make sure you have received all of the items

shown below. If your Dryer was damaged during shipping, or you do not have all of the items, contact

1-800-SAMSUNG (726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,

etc.) well out of childrens’ reach

Parts supplied

“Y”-connector Short inlet hose Rubber Washer Long inlet hose

01 installing your dryer

WARNING

Top Cover

Control panel

Door

Frame Front

Filter

Duct Exhaust

Water Inlet

[ BACK ]

DV5471AEP-03022B-01_EN.indd Sec3:9DV5471AEP-03022B-01_EN.indd Sec3:9 2011-07-22  8:37:332011-07-22  8:37:33

10_ installing your dryer

installing your dryer

Tools needed

Pliers Cutting knife

Pipe wrench

(gas only)

Nut drivers

Level Phillips Screwdriver Duct tape Wrench

BASIC REQUIRMENTS

Make sure you have everything necessary for proper installation

• A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.

• A POWER CORD for electric dryers (except in Canada).

• GAS LINES (if installing a gas dryer). The gas lines must meet national and local codes.

• EXHAUST SYSTEM - must be rigid metal or flexible stiff-walled metal exhaust ducting.

DV5471AEP-03022B-01_EN.indd Sec3:10DV5471AEP-03022B-01_EN.indd Sec3:10 2011-07-22  8:37:332011-07-22  8:37:33

installing your dryer _11

DUCTING REQUIREMENTS

• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

• Do not use a smaller duct.

• Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation.

Lint accumulation should be cleaned regularly.

• If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct

with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.

• Never install any type of flexible duct in walls, ceilings, or other concealed spaces.

• Keep the exhaust duct as straight and short as possible.

• Secure joints with duct tape. Do not use screws.

• Plastic flexible duct can kink, sag, be punctured, reduce airflow, extend drying times, and affect dryer

operation.

• Exhaust systems longer than recommended can extend drying times, affect machine operation, and

may collect lint.

• The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and

the entry of wildlife. Never use an exhaust hood with a magnetic damper.

• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and

the ground or other obstruction. The hood opening should point down.

• Never install a screen over the exhaust outlet.

• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

• If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly

down towards the exhaust hood to reduce condensation and lint buildup.

• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before

cleaning.

• Check frequently to be sure the exhaust hood damper opens and closes freely.

• Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then

check ducting for obstructions.

• Do not exhaust dryer into any wall, ceiling, crawl space, or concealed space of a building, gas vent, or

any other common duct or chimney. This could create a fire hazard from lint expelled by the dryer.

ELECTRIC AND GAS DRYER

Weather Hood Type

Recommended Use only for short-run installation

4” (10 .2 cm) 2.5” (6.4 cm)

No. of 90° elbows Rigid Metallic Flexible* Rigid Metallic Flexible*

0 80 ft. (24.4 m) 41 ft. (12.4 m) 74 ft. (22.6 m) 33 ft. (10.1 m)

1 68 ft. (20.7 m) 37 ft. (11.2 m) 62 ft. (18.9 m) 29 ft. (8.8 m)

2 57 ft. (17.4 m) 33 ft. (10.1 m) 51 ft. (15.5 m) 25 ft. (7.6 m)

3 47 ft. (14.3m) 29 ft. (8.8 m) 41 ft. (12.5 m) 21 ft. (6.5 m)

* Do not use non-metallic flexible duct.

01 installing your dryer

DV5471AEP-03022B-01_EN.indd Sec3:11DV5471AEP-03022B-01_EN.indd Sec3:11 2011-07-22  8:37:332011-07-22  8:37:33

12_ installing your dryer

If the new dryer is being installed into an existing exhaust system, you must

make sure:

• The exhaust system meets all local, state, and national codes.

• That a flexible plastic duct is not used.

• To Inspect and clean all lint buildup from inside the existing duct.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be

less than 0.

This can be measured with the dryer running with a manometer at the point where the exhaust

duct connects to the dryer. A no-heat setting should be used. The dryer tumbler should be

empty and the lint filter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept

for future reference.

Remove the door from all discarded appliances to avoid the danger of a child suffocating.

LOCATION CONSIDERATIONS

Locate the dryer where there is enough space at the front for loading the dryer, and enough space behind

for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the bottom or the right

or the left (electric model only), use the accessory exhaust kit (sold separately). Instructions are included

with the kit. It’s important to make sure the room has enough fresh air. The dryer must be located where

there is no air-flow obstruction.

On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air

for combustion and proper dryer operation.

Do not install or store the dryer in an area where it will be exposed to water and/or weather. Keep the dryer

area clear of combustible materials, casoline, and other fl ammable vapors and liquids. A dryer produces

combustible lint. The area around the dryer should be kept Lint-Free.

ALCOVE OR CLOSET INSTALLATION

You must exhaust the dryer to the outside to reduce the risk of fi re when installed in an alcove or

closet.

• No other fuel-burning appliance should be installed in the same closet as the dryer.

• WARNING: To reduce the risk of fi re, you must exhaust the dryer to the outdoors.

See Exhaust information section.

• Minimum clearances between the dryer and adjacent walls or other surfaces are:

2” in front, 17” on top, 1” on either side, and 5” in the back.

• The closet front must have two unobstructed air openings for a combined minimum total area of 72 in²

with 3” minimum clearance on the top and bottom. A louvered door with equivalent space clearance is

acceptable.

installing your dryer

WARNING

DV5471AEP-03022B-01_EN.indd Sec3:12DV5471AEP-03022B-01_EN.indd Sec3:12 2011-07-22  8:37:342011-07-22  8:37:34

installing your dryer _13

MOBILE HOME INSTALLATION

The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and

Safety Standard Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD (Part 280), 1975} for the CANADA) or CSA Standards Z240 (for Canada).

When installing a dryer in a mobile home, you must make provisions for anchoring the dryer to the floor.

Locate the dryer in an area that has adequate fresh air.

A minimum of 72 in² (465 cm²) of unobstructed space is required.

Call 1-800-SAMSUNG(726-7864) for information on purchasing the Floor Anchoring Kit as an accessory.

All mobile home installations must be exhausted to the outside with the exhaust duct termination securely

fastened to the mobile home structure, using materials that will not support combustion.

The exhaust duct may not terminate underneath the mobile home.

See Exhausting section for more information.

EXHAUSTING

Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the

room.

In the CANADA:

• All dryers must be exhausted to the outside.

• The required exhaust duct is 4 inches (10.2 cm) in diameter.

• Use only those foil-type fl exible ducts, if any, specifically identified for use with the appliance

by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct,

Subject 2158A.

• Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint.

In Canada:

• Use only those foil-type fl exible ducts, if any, specifically identified for use with the appliance

by the manufacturer.

• All dryers must be exhausted to the outside.

• The exhaust duct should be 4 inches (10.2 cm) in diameter.

Outside the U.S. and Canada:

• Refer to the local codes.

You must exhaust the dryer to the outside to reduce the risk of fi re when you install the

dryer in an alcove or closet.

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.

If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.

Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air,

heat, and lint.

01 installing your dryer

WARNING

DV5471AEP-03022B-01_EN.indd Sec3:13DV5471AEP-03022B-01_EN.indd Sec3:13 2011-07-22  8:37:342011-07-22  8:37:34

14_ installing your dryer

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL

CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE

CANADA), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP

(liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas

line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off

valve be installed within 6” of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge

connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the

system.

DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas

Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.

• As a courtesy, most local gas utilities will inspect a gas appliance installation.

GAS IGNITION – Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

COMMONWEALTH OF MASSACHUSETTS INSTALLATION

INSTRUCTIONS

Your dryer must be installed by a licensed plumber or gas fitter. A “T” handle manual gas valve must be

installed in the gas supply line to your dryer. If a flexible gas connector is used to install your dryer, the

connector can be no longer than 3’ (36”).

• Gas leaks may occur in your system, creating a dangerous situation.

• Gas leaks may not be detected by smell alone.

• Gas suppliers recommend you purchase and install a UL-approved gas detector.

• Install and use in accordance with manufacturer’s instructions.

installing your dryer

WARNING

DV5471AEP-03022B-01_EN.indd Sec3:14DV5471AEP-03022B-01_EN.indd Sec3:14 2011-07-22  8:37:342011-07-22  8:37:34

installing your dryer _15

ELECTRICAL REQUIREMENTS

Wiring diagram is located on the plate below the control panel or frame back.

• Improper connection of the equipment grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is

properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet,

have a proper outlet installed by a qualified electrician.

• To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code

CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide

adequate electrical services for your dryer.

• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest

Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and

local codes and ordinances.

GROUNDING

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of

electrical shock by providing a path of least resistance for the electrical current.

Gas models

Your dryer has a cord with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

Electric models

Your dryer has a cord with an equipment-grounding conductor and a grounding plug, sold

separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet

installed by a qualified electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must

be connected to a permanently grounded metal wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment grounding

terminal.

01 installing your dryer

WARNING

DV5471AEP-03022B-01_EN.indd Sec3:15DV5471AEP-03022B-01_EN.indd Sec3:15 2011-07-22  8:37:342011-07-22  8:37:34

16_ installing your dryer

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the Grounding section.

An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is

required.

Electric models – U.S. only

Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require

120/208 volt, 60 Hz approved electrical service. The electric service requirements can be found

on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of

the line is required.

• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

• The power cord is NOT provided with U.S. electric model dryers.

IMPORTANT:

When local codes allow, the dryer electrical supply may be connected by means of a new power

supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of120/240

volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop

terminals, open-end spade lugs with turned up ends, or with tinned leads.

• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring

must be retained at the dryer cabinet with a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit

grounding through the neutral conductor. (Use 4-prong plug for 4 wire receptacle, NEMA

type 14-30R.)

Electric models – Canada Only

• A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or

circuit breaker on both sides of the line is required.

• All Canadian models are shipped with the power cord attached. The power cord should be

plugged into a 30-ampere receptacle.

It is not permissible to convert a dryer in Canada to 208 volts.

installing your dryer

DV5471AEP-03022B-01_EN.indd Sec3:16DV5471AEP-03022B-01_EN.indd Sec3:16 2011-07-22  8:37:342011-07-22  8:37:34

installing your dryer _17

INSTALLATION - GENERAL PROCEDURE

For proper installation, we recommend that you hire a qualified installer.

Read these instructions completely before you begin the installation.

To install the dryer, follow these steps:

1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-

by-side so you have easy access to both appliances.

To move the dryer easily, lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it

lies across both cushion-tops. Push the dryer so that it is near its final location. Set your dryer upright.

Leave enough room around the dryer so you can attach the duct work, power cord, etc.

2. If you need to change the direction of the door, go to Door Reversal on page . When done, return to

Step 3 below.

3. Review the Exhausting section before installing the exhaust system. Install the duct work from your

dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO

NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic

flexible exhaust material.

A tip for tight installations: Attach a section of the exhaust system to your dryer before putting it in

place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the

back of the dryer cabinet.

4. If you have an electric model, skip to Step 6. If you have a gas model, go to the next step.

5. Review the Gas Requirements section, then follow the lettered steps below.

a. Remove the pipe thread protective cap.

b. Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections.

The pipe joint compound must be resistant to the action of any liquefied petroleum gas.

c. Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4” (1.9 cm)

female thread end of a flexible connector to the 3/8” (1 cm) male threaded end on the dryer.

d. Securely tighten the gas line fitting over the threads.

e. Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles

appear, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.

f. Go to Step 6 on the next page

01 installing your dryer

DV5471AEP-03022B-01_EN.indd Sec3:17DV5471AEP-03022B-01_EN.indd Sec3:17 2011-07-22  8:37:342011-07-22  8:37:34

18_ installing your dryer

installing your dryer

6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step

7) or 4 Wire system instructions (Step 8) below.

7. Three Wire system instructions:

A. External ground connector

B. Neutral grounding wire (green/yellow)

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. 3/4” (1.9 cm) UL-listed strain relief

1. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the

power cord to the center, silver-colored terminal screw

of the terminal block. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your Dryer’s rear panel slot.

Secure the cover with a hold-down screw.

If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap

to the terminal block support to ground the dryer frame to the neutral conductor.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

8. Four Wire System instructions:

A. External ground connector

B. Green or bare copper wire of power cord

C. 3/4” (1.9 cm) UL-listed strain relief

D. Center silver-colored terminal block screw

E. Neutral Grounding wire (green/yellow)

F. Neutral wire (white or center wire)

1. Remove the External ground connector screw.

2. Connect the ground wire (green or unwrapped) of the power cord to the external ground

connector screw. If you want to connect B (Green or bare copper wire of power cord) to

the Neutral Post without assembling with A (cabinet ground), call the service technician.

3. Loosen or remove the center terminal block screw.

4. Connect the neutral wire (white or center wire) of the power cord and the appliance

ground wire (green with yellow stripes) under the central screw of the terminal block.

5. Connect the other wires to the outer terminal block screws. Tighten screws.

6. Tighten the strain relief screws.

7. Insert the tab of the terminal block cover into your Dryer’s rear panel slot.

Secure the cover with a hold-down screw.

We recommend using Ring terminals. If you use Strap terminals, please ensure you install

them perfectly.

WARNING

DV5471AEP-03022B-01_EN.indd Sec3:18DV5471AEP-03022B-01_EN.indd Sec3:18 2011-07-22  8:37:342011-07-22  8:37:34

installing your dryer _19

U.S. MODELS:

IMPORTANT – All U.S. models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is

grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for

new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral.

If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal

block.

Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole

provided in the cabinet near the terminal block.

A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are

tight. Use a 3/8” (1 cm) deep well socket.

9. Connect the Water Inlet Hose. For instructions, go to Connecting the

Inlet Hose on page

10. To ensure that the dryer provides optimal drying performance, it must

be level. To level the dryer, follow the lettered steps below:

a. Using a level, check if the dryer is level side to side and then front

to back.

b. If the dryer is not level, adjust the leveling feet on the bottom of

the dryer until the washer is level side to side and back to front.

Turning the feet clockwise retracts the feet. Turning the feet

clockwise loosens and extends them.

To set the dryer to the same height as the washer, fully

retract the leveling feet by turning them counterclockwise,

then loosen the feet by turning them clockwise. Once

the dryer is the same height as the washer, follow the

directions above to level the dryer.

Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling

feet more than necessary can cause the dryer to vibrate.

11. Make sure all gas connections (on gas models), exhaust, and electrical connections are complete. Plug

in your dryer, and then check its operation by using the checklist below.

12. For GAS MODELS ONLY

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat

setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5

minutes. Be sure the gas supply to your dryer has been turned on. To confirm gas ignition, check the

exhaust for heat.

FINAL INSTALLATION CHECKLIST

 The dryer is plugged into an electrical outlet and grounded properly.

 The exhaust ductwork is hooked up and the joints are taped.

 You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct.

 The dryer is level and is sitting firmly on the floor.

 For gas models: The gas is turned on and there are no gas leaks.

 Start your dryer to confirm that it runs, heats, and shuts off.

01 installing your dryer

Level

Leveling feet

Retract fully Then loosen

DV5471AEP-03022B-01_EN.indd Sec3:19DV5471AEP-03022B-01_EN.indd Sec3:19 2011-07-22  8:37:342011-07-22  8:37:34

20_ installing your dryer

installing your dryer

CONNECTING THE INLET HOSE

Method1 - Using the Y Connector and Long Hose

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old

hoses.

1. Turn off the cold water faucet.

2. If you have a washer water hose attached to the cold water

faucet, unscrew and remove the hose.

3. If space permits, attach the brass female end of the

“Y”connector to the cold water faucet. Turn by hand until

tight.

4. Attach the straight end of the long hose to the “Y’ connector.

Screw on the hose coupling by hand until it is tight.

5. Using pliers, tighten the hose coupling with an additional two

thirds turn.

Do not overtighten. You can damage the coupling.

6. Attach the angled end of the long hose to the fill valve at the

bottom of the dryer’s rear frame. Screw on the coupling by

hand until it is tight.

7. Using pliers, tighten the hose coupling with an additional two

thirds turn.

Do not overtighten. You can damage the coupling.

8.

Attach the water hose to the other side of the “Y” connector. Screw on the hose coupling until it

is tight. Using pliers, tighten the coupling with an additional two thirds turn.

Do not overtighten. You can damage the coupling.

9. Turn the water faucet on.

10. Check for leaks around “Y” connector, faucets, and hoses.

Duct Exhaust

Frame

(back)

Water Hose

Y-Connector

Water Hose

DV5471AEP-03022B-01_EN.indd Sec3:20DV5471AEP-03022B-01_EN.indd Sec3:20 2011-07-22  8:37:342011-07-22  8:37:34

La page charge ...

Samsung DV5471AEP Le manuel du propriétaire

Samsung DV5471AEP Le manuel du propriétaire

dans d''autres langues

Documents connexes