TP-LINK TL-SG1008P Guide d'installation

Catégorie
Commutateurs réseau
Taper
Guide d'installation
Connection
© 2020 TP-Link 7106508569 REV3.1.0
Installation Guide
Gigabit Desktop Switch with PoE/PoE+
LED Explanation
Power
On: Power on
O: Power o
Link/Act (For TL-SG1008P)
On: A device is linked to the correspoding
port and running properly.
Flashing: Transmitting or receiving data.
O: No device is linked to the
corresponding port.
Link/Act, Uplink 1, Uplink 2 (For TL-SG1210P)
Green On: Running at 1000 Mbps, but no activity.
Green Flashing: Running at 1000 Mbps and is
transmitting or receiving data.
Yellow On: Running at 10/100 Mbps, but no activity.
Yellow Flashing: Running at 10/100 Mbps and is
transmitting or receiving data.
O: No device is linked to the corresponding port.
Package Contents: Switch, Power Adapter, Power Cord and Installation Guide.
On: Providing PoE power
Flashing: PoE fault
O: Not providing PoE power
PoE Status
On: Running at 1000 Mbps.
O: Running at 10/100 Mbps or no device
is linked to the corresponding port.
1000Mbps (For TL-SG1008P)
PoE MAX
For TL-SG1008P:
On: 48 W≤Total power supply < 55 W
Flashing: Total power supply 55 W
O: Total power supply < 48 W
For TL-SG1210P:
On: 56 W≤Total power supply < 63 W
Flashing: Total power supply 63 W
O: Total power supply < 56 W
Note: For simplicity, we will take TL-SG1008P for example throughout the Guide.
PC
IP Camera AP
Ethernet Ports (1-8)
PoE Ports (1-4)
IP Phone
PoE Devices
Router
LAN PortWAN Port
Internet
DC Power Adapter
AC Power Cord
Note:
PoE/PoE+ ports typically connect to PoE Devices. Besides, PoE/PoE+ ports can also connect to non-PoE devices, but only transmit data.
TL-SG1210P has two uplink ports, which typically connect to uplink devices like routers.
Uplink 1 is an SFP port and works with a 1000 Mbps SFP module. Uplink 2 is an RJ45 port.
For TL-SG1008P, maximum PoE power is 15.4 W for each PoE port and 55 W for all PoE ports in total.
For TL-SG1210P, maximum PoE power is 30 W for each PoE port and 63 W for all PoE ports in total.
1.
2.
3.
4.
PoE budget calculations are based on laboratory testing. Actual PoE power budget is not guranteed and will vary as a result of client
limitations and environmental factors.
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally.
If the Power LED is not lit, please try the following:
A1:
Make sure the AC power cord is connected to the switch with power
source properly.
A2:
Make sure the voltage of the power supply meets the requirements
of the input voltage of the switch.
A3: Make sure the power source is ON.
Q1. Why is the Power LED not lit?
Please try the following:
A1:
Make sure that the cable connectors are rmly plugged into the
switch and the device.
A2
:
Make sure the connected device is turned on and works normally.
A3
:
The cable must be less than 100 meters long (328 feet).
Q2. Why is the Link/Act LED not lit while a device is
connected to the corresponding port?
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0˚C to 40˚C (32˚F to 104˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Environmental and Physical Specications
IEEE 802.3i, 802.3u, 802.3ab, 802.3x, 802.3af, 802.1p
For TL-SG1210P: IEEE 802.3z, 802.3at
CSMA/CD
For TL-SG1008P:
8 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation
MDI/MDIX;
PoE Ports: Port 1-Port 4, Total Power Supply: 55 W
For TL-SG1210P:
9 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation
MDI/MDIX; 1 1000 Mbps SFP port;
PoE Ports: Port 1-Port 8, Total Power Supply: 63 W
10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);
EIA/TIA-568 100 Ω STP (maximum 100 m)
100BASE-TX: UTP category 5, 5e cable (maximum 100 m);
EIA/TIA-568 100 Ω STP (maximum 100 m)
1000BASE-T: UTP category 5e cable or above (maximum
100 m); EIA/TIA-568 100 Ω STP (maximum 100 m)
1000BASE-SX/LX/LX10/BX10: MMF, SMF (For
TL-SG1210P)
For TL-SG1008P: 16 Gbps
For TL-SG1210P: 20 Gbps
4K
Store-and-Forward
Automatically learning, automatically aging
External Power Adapter
Input: 100-240 V AC, 50/60 Hz
Output:
For TL-SG1008P: 48 V DC/1.25 A
For TL-SG1210P: 53.5 V DC/1.31 A
Standard
General Specications
Specications
Q3. Why is PoE/PoE+ ports not supplying power for PoE devices?
If total power consumption of connected PoE devices exceeds the maximum, the
system will cut o the power to ports with the lowest PoE priority. A PoE port with
a smaller index number has a higher PoE priority. Let’s take TL-SG1008P as an
example. If port 1, 2 and 4 are consuming 15.4 W respectively, and an additional
PoE device with 12 W is connected to port 3, the total power consumption
exceeds 55 W, so the system will cut o the power to port 4.
Power Supply
MAC Address Learning
Transfer Method
MAC Address Table
Backbone Bandwidth
Network Media (Cable)
Interface
Protocol
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides,
welcome to email techwriter@tp-link.com.cn.
To ask questions, find answers, and communicate with TP-Link
users or engineers, please visit https://community.tp-link.com
to join TP-Link Community.
Wall Mountable
For TL-SG1008P: No
For TL-SG1210P: Yes
Distance Between
Mounting Holes
For TL-SG1210P: 150 mm
FCC compliance information statement
限用物質含有情況標示聲明書
限用物質及其化學符號
Pb
Cd
Hg
六價鉻
CrVI
多溴聯苯
PBB
多溴二苯醚
PBDE
產品元件名稱
PCB
外殼
電源供應器
備考1. “ “系指該項限用物質之百分比含量未超出百分比含量基準值。
備考2. “ “系指該項限用物質為排除項目。
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用以確保本產品的操作可靠並防止過熱請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風否則不可放在密閉位置中。
請不要私自打開機殼不要嘗試自行維修本產品請由授權的專業人士進行此項工作。
Explanation of the symbols on the product label
DC voltage
AC voltage
Class II equipment
Polarity of output terminals
Energy eciency marking
Indoor use only
RECYCLING
This product bears the selective sorting symbol for Waste
electrical and electronic equipment (WEEE). This means that this
product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or
electronic equipment.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Safety Information
Adapter shall be installed near the equipment and shall be easily accessible.
Place the device with its bottom surface downward.
Do not use any other chargers than those recommended.
Keep the device away from water, re, humidity or hot environments.
Do not use damaged charger or USB cable to charge the device.
Do not attempt to disassemble, repair, or modify the device.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
Note: The product label can be found at the bottom of the product.
Product Name: 8-Port Gigabit Desktop Switch with 4-Port PoE /
10-Port Gigabit Desktop Switch with 8-Port PoE+
Model Number: TL-SG1008P/TP-SG1210P
Component Name Model
T480125-2-DT (For TL-SG1008P)
T535131-2-DT (For TP-SG1210P)
I.T.E. Power Supply
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Consult the dealer or an experienced radio/ TV technician for help.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
Product Name: I.T.E. Power Supply
Model Number: T480125-2-DT/T535131-2-DT
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на
відповідність вимогам нормативних документів та вимогам, що передбачені
чинними законодавчими актами України.
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
CE Mark Warning
Canadian Compliance Statement
This is a class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU,
2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at
https://www.tp-link.com/en/ce.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
We, TP-Link USA Corporation, has determined that the equipment shown as
above has been shown to comply with the applicable technical standards, FCC
part 15. There is no unauthorized change is made in the equipment and the
equipment is properly maintained and operated.
Issue Date: 2019/12/02
  • Page 1 1
  • Page 2 2
  • Page 3 3

TP-LINK TL-SG1008P Guide d'installation

Catégorie
Commutateurs réseau
Taper
Guide d'installation

dans d''autres langues