GE 040330HD-0 Le manuel du propriétaire

GE Home Generator Systems

15,000 and 20,000 Watt

Home Generator Systems

Operator’s Manual

Not for

Reproduction

2

Thank you for purchasing this quality-built GE home generator. We’re pleased that you’ve placed your confidence in

the GE brand. When operated and maintained according to the instructions in this manual, your home generator will

provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with home standby

generators and how to avoid them. Because we do not necessarily know all the applications this equipment could

be used for, it is important that you read and understand these instructions thoroughly before attempting to start or

operate this equipment. Save these instructions for future reference.

This home standby generator requires professional installation before use. Refer to the separate installation manual

for full information. Your installer should follow the instructions completely.

Where to Find Us

You never have to look far to find GE support and service for your generator. For quick service when you need it, keep

your original receipt with this manual. You may contact Customer Service at 888 575‑8226 or click on Find a Dealer at

BRIGGSandSTRATTON.COM, which provides a list of authorized dealers.

Generator and engine model and serial numbers should be recorded in the installation manual.

Not for

Reproduction

3

Table of Contents

Important Safety Instructions ...............................4

Installation ................................................7

For the Home Owner..................................................7

For the Installing Dealer/Contractor....................................7

Owner Orientation....................................................8

Fuel Factors..........................................................8

Generator Location ...................................................9

Delivery Inspection ..................................................10

Controls ..................................................11

Operation.................................................14

Automatic Operation ................................................14

Setting Exercise Timer ...............................................15

Maintenance ..............................................16

Fault Detection System ..............................................16

Generator Maintenance ..............................................18

Engine Oil...........................................................18

Battery .............................................................19

Cleaning the Generator ..............................................20

Storage.............................................................21

Troubleshooting ...........................................22

Warranty .................................................23

Product Speciﬁcations .....................................25

Not for

Reproduction

4

Safety Rules

Explosion

Fire

Electrical Shock

Rotating Parts

Hot Surface

Toxic Fumes

Chemical BurnExplosive PressureAuto Start

Lift Hazard

Read Manual

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could cause headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea, fainting

or death.

Operate generator ONLY outdoors.•

Install a battery operated carbon monoxide alarm near •

the bedrooms.

Keep exhaust gas from entering a confined area through •

windows, doors, ventilation intakes, or other openings.

WARNING The engine exhaust from this product contains

chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

WARNING Certain components in this product and related

accessories contain chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm. Wash

hands after handling.

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a degree

or level of hazard seriousness. A safety symbol may be used

to represent the type of hazard. The signal word NOTICE is

used to address practices not related to personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

Important Safety Instructions

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and the tags and decals affixed to the unit

are, therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the generator system unsafe.

Not for

Reproduction

5

WARNING Storage batteries give off explosive hydrogen gas

during recharging.

Slightest spark will ignite hydrogen and

cause explosion.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery contents will cause severe chemical burns.

A battery presents a risk of electrical shock and high short

circuit current.

DO NOT dispose of battery in a fire. Recycle battery.•

DO NOT allow any open flame, spark, heat, or lit cigarette during •

and for several minutes after charging a battery.

DO NOT open or mutilate the battery.•

Wear protective goggles, rubber apron, rubber boots and •

rubber gloves.

Remove watches, rings, or other metal objects.•

Use tools having insulated handles.•

WARNING Generator produces hazardous voltage.

Failure to properly ground generator can result in

electrocution.

Failure to isolate generator from power utility could result

in death or injury to electric utility workers due to backfeed

of electrical energy.

When using generator for backup power, notify utility company.•

DO NOT touch bare wires or bare receptacles.•

DO NOT use generator with electrical cords which are worn, •

frayed, bare or otherwise damaged.

DO NOT handle generator or electrical cords while standing in •

water, while barefoot, or while hands or feet are wet.

If you must work around a unit while it is operating, stand on an •

insulated dry surface to reduce the risk of a shock hazard.

DO NOT allow unqualified persons or children to operate or •

service generator.

In case of an accident caused by electrical shock, immediately •

shut down the source of electrical power and contact the local

authorities. Avoid direct contact with the victim.

Despite the safe design of the residential generator, operating •

this equipment imprudently, neglecting its maintenance or being

careless can cause possible injury or death.

Remain alert at all times while working on this equipment. •

Never work on the equipment when you are physically or

mentally fatigued.

Before performing any maintenance on the generator, disconnect •

the battery cable indicated by a NEGATIVE, NEG or (‑) first. When

finished, reconnect that cable last.

After your system is installed, the generator may crank and start •

without warning any time there is a power failure. To prevent

possible injury, always set the generator’s system switch to OFF,

remove the service disconnect from the disconnect box AND

remove the 15 Amp fuse BEFORE working on the equipment.

WARNING Propane and Natural Gas are extremely flammable

and explosive.

Fire or explosion could cause severe burns

or death.

Install the fuel supply system according to NFPA 37 and other •

applicable fuel-gas codes.

Before placing the generator into service, the fuel system lines •

must be properly purged and leak tested.

After the generator is installed, you should inspect the fuel •

system periodically.

NO leakage is permitted.•

DO NOT operate engine if smell of fuel is present or other •

explosive conditions exist.

DO NOT smoke around the generator. Wipe up any oil spills •

immediately. Ensure that no combustible materials are left in the

generator compartment. Keep the area near the generator clean

and free of debris.

Not for

Reproduction

6

WARNING Contact with muffler area could result in

serious burns.

Exhaust heat/gases can ignite combustibles or

structures causing a fire.

DO NOT touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

DO NOT install the generator closer than 5 feet (1.5m) from any •

combustibles or structures with combustible walls having a fire

resistance rating of less than 1 hour.

Keep at least minimum distances shown in • General Location

Guidelines to insure for proper generator cooling and

maintenance clearances.

It is a violation of California Public Resource Code, Section 4442, •

to use or operate the engine on any forest-covered, brush-

covered, or grass-covered land unless the exhaust system is

equipped with a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states or federal

jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer to

obtain a spark arrester designed for the exhaust system installed

on this engine.

Replacement parts must be the same and installed in the same •

position as the original parts.

WARNING Starter and other rotating parts could entangle

hands, hair, clothing, or accessories.

NEVER operate generator without protective housings, covers, or •

guards in place.

DO NOT wear loose clothing, jewelry or anything that may be •

caught in the starter or other rotating parts.

Tie up long hair and remove jewelry.•

Before servicing, remove 15 Amp fuse from control panel and •

disconnect Negative (NEG or ‑) battery cable.

CAUTION Installing the 15A fuse could cause the engine

to start.

Observe that the 15 Amp fuse has been removed from the control •

panel for shipping.

DO NOT install this fuse until all plumbing and wiring has been •

completed and inspected.

CAUTION Excessively high operating speeds increase risk of

injury and damage to generator.

Excessively low speeds impose a heavy load on generator.

DO NOT tamper with governed speed. Generator supplies correct •

rated frequency and voltage when running at governed speed.

DO NOT modify generator in any way.•

NOTICE Improper treatment of generator could damage it and

shorten its life.

Use generator only for intended uses.•

If you have questions about intended use, contact your •

authorized dealer.

Operate generator only on level surfaces.•

Adequate, unobstructed flow of cooling and ventilating air is •

critical to correct generator operation.

The access panels/door must be installed whenever the unit •

is running.

DO NOT expose generator to excessive moisture, dust, dirt, or •

corrosive vapors.

Remain alert at all times while working on this equipment. •

Never work on the equipment when you are physically or

mentally fatigued.

DO NOT start engine with air cleaner or air cleaner cover removed.•

DO NOT insert any objects through cooling slots.•

DO NOT use the generator or any of its parts as a step. Stepping •

on the unit can cause stress and break parts. This may result in

dangerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.

If connected devices overheat, turn them off and disconnect them •

from generator.

Shut off generator if: •

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

NOTICE Exceeding generators wattage/amperage capacity could

damage generator and/or electrical devices connected to it.

Start generator and let engine stabilize before connecting •

electrical loads.

Not for

Reproduction

7

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand Owner Orientation in this

manual before contracting or starting your home

generator installation.

To arrange for proper installation, contact the store at which

you purchased your home generator, your dealer, a licensed

electrician or your utility power provider.

The home generator warranty is VOID unless the system is

installed by licensed electrical and plumbing professionals.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

The Emission Control System for this generator is warranted

for standards set by the U.S. Environmental Protection

Agency and by the California Air Resources Board (CARB).

For the Home Owner

If you need more information in this matter, please call

888 575‑8226 between 8:00 AM and 5:00 PM CT.

For most applications, the installation manual contains all

the information required to properly install and start the

home generator. This operator’s manual describes routine

operation and owner maintenance procedures.

For the Installing Dealer/Contractor

Installation

We sincerely appreciate your patronage. For this reason, we

have made every effort to provide for a safe, streamlined

and cost-effective installation. Because each installation is

unique, it is impossible to know of and advise the trade of all

conceivable procedures and methods by which installation

might be achieved. Neither could we know of possible

hazards and/or the results of each method or procedure.

For these reasons, only current licensed electrical

and plumbing professionals should attempt home

generator system installations. Installations must strictly

comply with all applicable codes, industry standards

and regulations.

Your home generator is supplied with this “Operator’s

Manual” and a separate “Installation Manual”. These are

important documents and should be retained by the owner

after the installation has been completed.

Not for

Reproduction

8

Power Decrease at High Altitude or

High Temperature

Air density is less at high altitudes, resulting in less available

engine power. Specifically, engine power will decrease 3.5%

for each 1,000 feet (300 meters) above sea level and 1%

for each 10° F (5.6°C) above 77°F (25°C). Make sure you and

your installer consider these factors when determining total

generator load.

An important consideration affecting the entire installation

is the type of fuel used by your home generator. The system

was factory tested and adjusted using natural gas, but can

be converted to use LP vapor. For proper engine function,

factors that are inherent to each of these fuels, your

location and the duration of possible utility interruptions are

important considerations in the following fuel guidelines:

 • Useclean,dryfuel,freeofmoistureorany

particulate material. Using fuels outside the

following recommended values may cause

performance problems.

 • Inenginessetuptorunonpropane(LP),commercial

grade HD5 propane with a minimum fuel energy of

2500 BTUs/ft3 with maximum propylene content of

5% and butane and heavier gas content of 2.5% and

minimum propane content of 90%.

Natural gas rating will depend on specific fuel but typical

derates are between 10 to 20% off the LP gas rating.

Fuel Factors

WARNING Propane and Natural Gas are extremely flammable

and explosive.

Fire or explosion could cause severe burns

or death.

The residential generator is equipped with an automatic safety •

gas “fuel shut-off” valve.

DO NOT operate the equipment if the “fuel shut-off” valve is •

missing or inoperative.

gaseous fuel supply increases, and the number of 90 degree

bends in the fuel supply increases; compensations in piping

and wiring materials must be made. This is necessary to

comply with local codes and overcome electrical voltage

drops and gaseous fuel pressure drops.

The factors mentioned above will have a direct affect on

the overall price of your home generator installation.

In some areas you may need to acquire electrical permits for

installing the home generator, building permits for installing

gas lines, and permits for noise allowances. Your installer

should check your local codes AND obtain the permits before

installing the system.

This section provides home generator owners with the

information necessary to achieve the most satisfactory and

cost effective installation possible.

The illustrations are for typical circumstances and are meant

to familiarize you with the installation options available with

your home generator. A thorough understanding of these

options will provide fundamental control over the cost of

your installation, as well as ensure your final satisfaction

and security.

Federal and local codes, appearance, noise levels, fuel types,

and distances are the factors that must be considered when

negotiating with an installation professional. Remember

that as the distance from the existing electrical service and

Owner Orientation

Not for

Reproduction

9

The actual physical location of your home generator has a

direct affect on:

1. The amount of plumbing required to fuel

your generator.

2. The amount of wiring required to control and connect

your generator.

Specific location guidelines are discussed in the installation

manual. Acquaint yourself with that information and confer

with your installer. Be sure to ask how your site might

affect installation costs and compliance with local codes

and standards.

The generator must be installed outdoors. DO NOT install

generator where exhaust gas could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes or other openings that can allow exhaust

gas to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when positioning

generator. See the installation manual for full details on safe

generator location.

Generator Location

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could cause headache,

fatigue, dizziness, vomiting, confusion, seizures, nausea,

fainting or death.

Operate generator ONLY outdoors.•

Install a battery operated carbon monoxide alarm near •

the bedrooms.

Keep exhaust gas from entering a confined area through •

windows, doors, ventilation intakes, or other openings.

WARNING Exhaust heat/gases could ignite combustibles or

structures causing a fire.

DO NOT install the generator closer than 5 feet (1.5m) from any •

combustibles or structures with combustible walls having a fire

resistance rating of less than 1 hour.

Not for

Reproduction

10

Carefully inspect the home generator for any damage that

may have occurred during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight bill

and affix his signature under the consignor’s memo of loss or

damage. If loss or damage is noted after delivery, separate

the damaged materials and contact the carrier and your

installer for claim procedures. Missing or damaged parts are

not warranted.

The home generator system is supplied with:

 • Pre-attachedmountingpad

 • Fully-servicedoil/lubricatingsystem

 • Flexiblefuelhook-uphose

 • Installationandstart-upmanual

 • Operator’smanual

 • Engineoperator’smanual

 • Installationchecklist

 • Alternatorcover

 • Spareaccessdoorkeys

 • Spare15Afuse

 • Twopincontrolpanelconnector

 • Tenpincontrolpanelconnector

 • Touchuppaint

Not included:

 • Startingbattery

 • Connectingwireandconduit

 • Fuelsupplyvalves/plumbing

 • Variousspecialtytools/equipment

Delivery Inspection

Not for

Reproduction

11

Read this operator’s manual and Important Safety Instructions before operating your generator.

Compare the illustration with your generator to familiarize yourself with the locations of various

controls and adjustments. Save this manual for future reference.

Home Generator

Generator is shown with access covers removed for clarity.

A ‑ Oil Fill Cap—Removetoservicetheenginewith

recommended oil.

B ‑ Control Panel—Usedforvarioustest,operationand

maintenance functions. See System Control Panel.

C ‑ Control Panel Dooropening—Providesaccesstocontrol

panel and battery.

D ‑ Battery(installersupplied)—12VoltDC,valve-regulated,

rechargeable battery provides power to start the engine.

E ‑ ID Label(locatedonbase)—Identifiesunitbymodeland

serial number.

F ‑ Fuel Inlet—Fuelsupplyisconnectedhere.

G ‑ Engine Label—Identifiesenginemodelandtype.

H ‑ Oil Dip Stick—Usedtochecktheengineoillevel.

J ‑ Oil Fill Dooropening—Providesaccessforengineservicing.

K ‑ Oil Drain Dooropening—Providesaccessfor

engine servicing.

L ‑ Oil Filter—Filtersengineoiltoprolongsystemlife.

M ‑ Oil Drain Hose—Providedtofacilitateoilchanging.

N ‑ Air Cleaner —Protectsenginebyfilteringdustanddebris

out of intake air.

P ‑ Exhaust Port—High-performancemufflerlowersengine

noise to comply with most residential codes.

Controls

F G H J

K L M

P

N

A

D

B

E

C

Not for

Reproduction

12

A

D

B

E

C

F

Compare this control panel illustration with your generator to familiarize yourself

with the location of these important controls:

System Control Panel

A ‑ SET EXERCISE—Usedtosettheexercisecyclestart

time and day-of-the-week. Exercise cycle only occurs in

AUTO mode.

B – MANUAL OVER‑RIDE—WithsystemswitchinAUTO

position, push the manual over-ride switch to start the

generator. To turn off the generator, push and hold the

manual over-ride switch again until engine stops.

C ‑ 15 Amp Fuse—ProtectsthehomegeneratorDCcontrol

circuits. If the fuse has ‘blown’ (melted open) or was

removed, the engine cannot crank or start. Replace the

fuse using only an identical ATO 15A fuse.

D ‑ System Switch—Thistwo-positionswitchisthemost

important control on the system and is used as follows:

•“AUTO” position is the normal operating position. If a

utility power outage is sensed, the system will start the

generator. When utility power is restored, AUTO lets

the engine stabilize internal temperatures, shuts off the

generator, and waits for the next utility power outage.

•“OFF” position turns off running generator, prevents

unit from starting and resets any detected faults.

E ‑ Digital Display—Displaysthetotalnumberofhours

the generator has been running and fault codes. Used

to schedule maintenance tasks and for troubleshooting

operational problems with the home generator. A

constant number displayed indicates the total hours of

operation. Fault conditions will flash “FC” followed by a

fault code number. All fault conditions are described in

Fault Detection System.

F ‑ Circuit Breaker —Protectsthegeneratorfromshortsand

other over-current conditions. Must be ON to supply power

to the automatic transfer switch.

Not for

Reproduction

13

The home generator is equipped with an enclosure that has

several access doors. The doors are named for a significant

component located behind them, as follows:

A Control Panel door

B Fuel Inlet Port (shown for reference)

C Oil Drain door

D Exhaust Port (shown for reference)

E Oil Fill door

The oil and control panel doors must be installed whenever

the unit is running to assure proper cooling, reduce noise,

and for added safety.

Access Ports

Each home generator is suppied with a set of identical keys.

These keys fit the locks that secure the access doors.

To open access door:

1. Insert key into lock of access door handle and turn

key one quarter turn counterclockwise.

2. Grasp door’s handle and turn one quarter turn

counterclockwise to open. Remove key.

To close access door:

1. Close door and turn door’s handle one quarter

turn clockwise.

2. Insert key into lock of door handle and turn key one

quarter turn clockwise. Remove key.

Additional force may be required to fully close and

lock the doors because they create a pressurized seal

for the generator enclosure.

WARNING Contact with muffler and engine parts could result in

serious burns.

DO NOT touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

A DB EC

Not for

Reproduction

14

Operation

To select automatic operation, do the following:

1. Confirm 15 Amp fuse is installed in control panel.

2. Set the main distribution panel circuit breaker that

sends utility voltage to the transfer switch to ON.

3. Set the generator’s circuit breaker to its ON position.

4. Set the control panel system switch to AUTO.

Automatic Operation

CAUTION With the system switch set to AUTO, the engine may

crank and start at any time without warning.

To prevent possible injury that may be caused by such sudden •

starts, always set the system switch to OFF if performing

maintenance on the system.

Remove the 15 Amp fuse before working on or around the •

generator or transfer switch.

With the battery installed, all wiring to transfer switch and

home generator completed, utility power supplied to the

automatic transfer switch, and the unit in AUTO mode, the

battery receives a trickle charge while the engine is not

running. The trickle charge cannot be used to recharge a

battery that is completely discharged.

15 Amp Fuse

The generator’s 15 Amp fuse is critical to correct system

operation. The 15 Amp fuse was removed at the factory to

prevent the unit from starting during shipping. Your installer

will ensure the fuse is properly installed upon completion of

the installation.

Engine Oil

This engine is shipped from the factory pre-run and filled

with synthetic oil (API SJ/CF 5W-30). This allows for system

operation in a wide range of temperature and climate

conditions. Before starting the engine, check oil level as

described in the engine manual.

Battery

The installer must supply a valve-regulated, rechargeable

12 volt DC starting battery. See Battery in Final Installation

Considerations in the installation manual. Installer

must connect battery charge wire (wire #13) to positive

battery terminal!

Important Owner’s Considerations

WARNING Battery posts, terminals and related accessories

contain lead and lead compounds, chemicals known to the State

of California to cause cancer and reproductive harm. Wash hands

after handling.

NOTICE Any attempt to crank or start the engine before it has

been properly serviced with the recommended oil will result in

equipment failure.

Refer to • Maintenance in the operator’s manual and engine

manual for oil fill information.

Damage to equipment resulting from failure to follow this •

instruction will void engine and generator warranty.

Not for

Reproduction

15

The home generator is equipped with an exercise timer that

will start and exercise the system once every seven days.

During this exercise period, the unit runs for approximately

20 minutes and then shuts down. Electrical load transfer

DOES NOT occur during the exercise cycle (unless an utility

power outage occurs).

A button on the control panel is labeled “SET EXERCISE” (see

System Control Panel). The specific day and the specific

time of day this button is pressed is programmed into the

control board memory. This date and time is then used to

automatically initiate the system exercise cycle. The “SET

EXERCISE” legend on the control panel will flash until the set

exercise cycle is set.

To perform the Set Exercise procedure:

1. Choose the day and time you want your home

generator to exercise.

2. On that day and time, press and hold “SET EXERCISE”

for three seconds.

The “Set Exercise” display will illuminate then turn off

to confirm that the exercise timer has been set. Then

release the button.

The unit will crank and run the exercise cycle. During

the cycle, “Set Exercise” will illuminate.

Once the exercise cycle is complete, the unit will turn

off and “Set Exercise” will no longer be displayed.

The exercise cycle may be discontinued at anytime by

turning the System Switch to OFF.

3. The unit will then start and run it’s 20 minute exercise

cycle.

For example, if you press SET EXERCISE on Sunday morning

at 10:00 AM, the unit will run an immediate exercise cycle

and an exercise cycle every following Sunday at 10:00 AM

(+/- 1/2 hour).

“Set Exercise” will only work if the unit is in the AUTO mode

and this exact procedure is followed. The exerciser will need

to be re-set if the 15 Amp fuse is removed or changed, or if

the starting battery is disconnected.

If you want to change the day and time the unit exercises,

simply perform the “Set Exercise” procedure at the exact

weekday and time you want it to take place.

Generator will not exercise if timer is not set.

Setting Exercise Timer

Checking Automatic Operation

To check the system for proper automatic operation,

proceed as follows:

1. Turn OFF the service disconnect or main distribution

panel circuit breaker sending power to the automatic

transfer switch.

When utility voltage is lost and the sensor has timed

out, the engine will crank and start. Let the system go

through its entire automatic operation sequence.

2. With generator output supplying its loads, turn ON the

service disconnect or main distribution panel circuit

breaker that supplies utility power to the automatic

transfer switch.

3. The automatic transfer switch will transfer loads back

to utility power after a 5 minute minimum run time

and utility power is available.

4. The generator will run for one additional minute for

engine cool down, then will shut down.

If utility is restored and generator does not shut down after

10 minutes, set system switch to OFF and contact your

installer or local service center.

This completes the test procedures for automatic operation.

The home generator will now start automatically and will

supply power to the transfer switch when utility power is lost.

Not for

Reproduction

16

Maintenance

Before performing any generator maintenance, always

perform the following steps:

1. Set generator’s circuit breaker to its OFF position.

2. Set control panel system switch to OFF.

3. Remove 15 Amp fuse from control panel.

4. Utility voltage is present at generator control panel.

Disconnect power before servicing control panel by

removing the fuses from the transfer switch.

5. After all servicing has been completed, replace fuses

in transfer switch, replace 15 Amp fuse in control

panel, set system switch and circuit breaker ON

and reset exercise timer. See Setting Exercise Timer

in Operation.

Servicing the System

The generator may have to run for long periods of time

with no operator present. For that reason, the system is

equipped with sensors that automatically shut down the

generator in the event of potentially damaging conditions,

such as low oil pressure, high temperature, over speed, and

other conditions.

The generator’s control panel has a digital display that

shows fault codes, like “FC_1”. The table below lists the

detected fault, the fault code as displayed on the control

panel.

Fault Description Fault Codes

Low battery voltage FC_1

Low oil pressure FC_2

Low voltage FC_3

Engine does not start FC_4

Low frequency FC_5

Engine overspeed FC_6

High temperature FC_7

Transfer switch fault FC_8

Reset Fault Detection System

The operator must reset the fault detection system each time

it activates. To do so, place the control panel system switch

in the OFF position for 30 seconds or more. Remedy the

fault condition, then return the home generator to service

by placing the system switch in the AUTO position, installing

the 15 Amp fuse, and resetting the exercise timer. See Setting

Exercise Timer in Operation.

Low Battery Voltage (FC_1)

This fault is indicated by fault code FC_1. This condition

occurs if the generator cannot start because the starting

battery output power is below that needed to crank the

engine. Causes for this problem may be a faulty battery or

battery charge circuit.

To remedy the problem, contact your local service center to

check the battery charge output. Remove the 15 Amp fuse

and disconnect the battery from the generator. Take the

battery to a local battery store for analysis.

Reinstall the battery (replace if necessary - see Battery in

Final Installation Considerations in the installation manual).

Then reset the fault detection system, as described earlier.

Fault Detection System

Not for

Reproduction

17

Low Oil Pressure (FC_2)

This fault is indicated by fault code FC_2. The unit is equipped

with an oil pressure switch that uses normally closed

contacts held open by engine oil pressure during operation.

Should oil pressure drop below the 8 psi range, switch

contacts close and the engine is shut down.

To remedy the low oil pressure condition, add the

recommended oil to the FULL mark on the dipstick.

If the low oil pressure condition still exists, the engine will

start, then shut down again. The fault code will appear. In

this case, contact an authorized dealer.

Low Voltage (Generator, FC_3)

This fault is indicated by fault code FC_3. This condition

is caused by a restriction in the fuel flow, a broken or

disconnected signal lead, a failed alternator winding, the

control panel circuit breaker is open, or the generator is

overloaded.

To remedy the problem, contact your installer or an

authorized dealer.

Engine Does Not Start (FC_4)

This fault is indicated by fault code FC_4. This feature

prevents the generator from damaging itself if it continually

attempts to start in spite of another problem, such as no fuel

supply. Each time the system is directed to start, the unit

will crank for 10 seconds, pause for 10 seconds, and repeat.

If the system does not begin producing electricity after

approximately 2 minutes, the unit will stop cranking.

Check to make sure the generator’s circuit breaker is in the

ON position in order for the sensing leads to verify that the

unit is running.

The most likely cause of this problem is no fuel supply. Check

the internal and external fuel shut off valves to ensure they

are fully open. Other causes could be failed spark plug(s),

failed engine ignition, or the engine air filter is clogged. You

may need to contact your installer for assistance if you can’t

remedy these problems.

Low Frequency (FC_5)

This fault is indicated by fault code FC_5. This feature

protects devices connected to the transfer switch by shutting

the generator down if the engine runs slower than 55 Hz for

three seconds.

This condition is caused by a failed engine component or by

excessive loads on the generator. To remedy the problem,

contact your installer or an authorized dealer.

Engine Overspeed (FC_6)

This fault is indicated by fault code FC_6. This feature

protects devices connected to the transfer switch by shutting

the generator down if the engine happens to run faster than

the preset limit.

The overspeed fault is detected as follows:

 • Ifthegeneratoroutputfrequencyis65-70Hz,after

three seconds, the generator will shut down.

 • Ifthegeneratoroutputfrequencyisgreaterthan

70 Hz, the generator will shut down immediately.

This condition is caused by a failed engine component.

To remedy the problem, contact your installer or an

authorized dealer.

High Temperature (FC_7)

This fault is indicated by fault code FC_7. The contacts of

the temperature switch are normally open. If the engine

temperature exceeds approximately 149°C (300°F), the fault

is detected and the engine shuts down.

Common causes for this condition include running the unit

with access panels removed, obstructed air inlet or exhaust

port, low oil level, or debris in the engine cylinder cooling fins.

To resolve the problem, let the engine cool down and remove

any accumulated debris and obstructions. Ensure that all

access panels are installed whenever the unit is running.

Transfer Switch Fault (FC_8)

This fault is indicated by fault code FC_8 (if transfer switch is

equipped with fault detection).

The most likely cause of this fault is a blown fuse in the

transfer switch. To remedy the problem, contact your

installer or an authorized dealer.

Not for

Reproduction

18

The generator warranty does not cover items that have been

subjected to operator abuse or neglect. To receive full value

from the warranty, the operator must maintain the system

as instructed in the engine operator’s manual.

All adjustments should be made at least once each season.

Follow the requirements in the engine operator’s manual.

Generator maintenance consists of keeping the unit

clean. Operate the unit in an environment where it will

not be exposed to excessive dust, dirt, moisture or any

corrosive vapors. Cooling air louvers on the enclosure

must not become clogged with snow, leaves, or any other

foreign material. To prevent generator damage caused by

overheating, keep the enclosure cooling inlets and outlets

clean and unobstructed at all times.

Check the cleanliness of the unit frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible

on its exterior/interior surface. Inspect the air inlet and outlet

openings inside and outside the enclosure to ensure air flow

is not blocked.

DO NOT use direct spray from a garden hose to clean

generator. Water can enter the engine and generator and

cause problems.

Generator Maintenance

The engine is filled with synthetic oil (API SJ/CF 5W-30).

This allows for system operation in the widest range of

temperature and climate conditions.

The use of synthetic oil does not alter the required oil change

intervals described in the engine operator’s manual.

Engine Oil

Changing Engine Oil

KEEP OUT OF REACH OF CHILDREN. DON’T POLLUTE.

CONSERVE RESOURCES. RETURN USED OIL TO

COLLECTION CENTERS.

1. Set control board system switch to OFF.

2. Remove 15 Amp fuse from control panel.

3. Place oil drain hose into an approved container.

4. Remove brass fitting from end of drain hose.

Shown here is the oil drain hose (B) and the oil filter location

(A) for the generator:

Change oil while the engine is still warm from running, as

described in the engine operator’s manual.

5. When oil has drained, replace brass fitting on hose.

6. Add oil. See below.

CAUTION Avoid prolonged or repeated skin contact with used

motor oil.

Used motor oil has been shown to cause skin cancer in certain •

laboratory animals.

Thoroughly wash exposed areas with soap and water.•

B

A

Not for

Reproduction

19

Servicing of batteries is to be performed or supervised

by personnel knowledgeable of batteries and the

required precautions. Keep unauthorized personnel away

from batteries.

Battery

WARNING Battery posts, terminals and related accessories

contain lead and lead compounds, chemicals known to the State

of California to cause cancer and reproductive harm. Wash hands

after handling.

NOTICE Any attempt to crank or start the engine before it has

been properly serviced with the recommended oil will result in

equipment failure.

Refer to • Maintenance in the operator’s manual and engine

manual for oil fill information.

Damage to equipment resulting from failure to follow this •

instruction will void engine and generator warranty.

To fill your engine with oil:

Follow the synthetic oil grade recommendation and oil fill

instructions given in the engine operator’s manual.

If all engine servicing is complete, replace 15 Amp fuse in

control panel and reset exercise timer. See Setting Exercise

Timer in Operation.

8. Reinstall 15 Amp fuse in control panel.

9. Set generator’s system switch to AUTO.

10. Reset exercise timer. See Setting Exercise Timer.

DON’T POLLUTE. CONSERVE RESOURCES, RETURN

USED BATTERY TO RECYCLING COLLECTION CENTER.

Servicing the Battery

If it is necessary to service the battery, proceed as follows:

1. Set control board system switch to OFF.

2. Remove 15 Amp fuse from control panel.

3. Service or replace battery as required. See Battery

in Final Installation Considerations in the installation

manual for specific battery needed.

4. Connect red battery cable to battery positive terminal

(indicated by POSITIVE, POS, or (+)).

5. Connect the battery charge wire (wire #13) shown

as (C) to the battery positive terminal (indicated by

POSITIVE, POS, or (+)):

6. Connect black negative battery cable to negative

battery terminal (indicated by NEGATIVE, NEG, or (‑).

7. Ensure hardware on both positive and negative

battery terminals is secure and fully isolated.

C

Not for

Reproduction

20

1. Set control board system switch to OFF.

2. Remove 15 Amp fuse from control panel.

Cleaning the Generator

3. Clean generator as desired.

 • Useadampclothtowipeexteriorsurfacesclean.

 • Useasoft,bristlebrushtoloosencakedondirt,etc.

 • Useavacuumcleanertopickuploosedirtanddebris.

 • Uselowpressureair(nottoexceed25psi)toblow

away dirt. Inspect cooling air slots and openings on

the generator. These openings must be kept clean

and unobstructed.

4. Reinstall 15 Amp fuse in control panel.

5. Set generator’s system switch to AUTO.

6. Reset exercise timer. See Setting Exercise Timer.

NOTICE Improper treatment of generator can damage it and

shorten its life.

DO NOT expose generator to excessive moisture, dust, dirt, or •

corrosive vapors.

DO NOT insert any objects through cooling slots.•

Charging the Battery

If it is necessary to charge the battery, proceed as follows:

1. Set control board system switch to OFF.

2. Remove 15 Amp fuse from control panel.

3. Disconnect negative battery cable from negative

battery terminal (indicated by NEGATIVE, NEG, or (‑)).

4. Charge battery with battery charger at 2 Amps until

battery holds 12 Volts. DO NOT exceed 13.7 volts

when charging.

5. Connect negative battery cable to negative battery

terminal (indicated by NEGATIVE, NEG, or (‑)).

6. Ensure hardware on both positive and negative

battery terminals is secure.

7. Reinstall 15 Amp fuse in control panel.

8. Set generator’s system switch to AUTO.

9. Reset exercise timer. See Setting Exercise Timer.

NOTICE Failure to disconnect negative battery cable will result in

equipment failure.

DO NOT attempt to jump start the generator.•

Damage to equipment resulting from failure to follow this •

instruction will void engine and generator warranty.

CAUTION With the system switch set to AUTO, the engine may

crank and start at any time without warning.

To prevent possible injury that may be caused by such sudden •

starts, always set the system switch to OFF if performing

maintenance on the system.

Remove the 15 Amp fuse before working on or around the •

generator or transfer switch.

WARNING Storage batteries give off explosive hydrogen gas

during recharging.

Slightest spark will ignite hydrogen and

cause explosion.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery contents will cause severe chemical burns.

A battery presents a risk of electrical shock and high short

circuit current.

DO NOT dispose of battery in a fire. Recycle battery.•

DO NOT allow any open flame, spark, heat, or lit cigarette during •

and for several minutes after charging a battery.

DO NOT open or mutilate the battery.•

Wear protective goggles, rubber apron, rubber boots and •

rubber gloves.

Remove watches, rings, or other metal objects.•

Use tools having insulated handles.•

Not for

Reproduction

La page charge ...

GE 040330HD-0 Le manuel du propriétaire

GE 040330HD-0 Le manuel du propriétaire

dans d''autres langues