Simplicity 020770-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020770-00

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Ce manuel convient également à

Manual No. 80089526 Rev -

Pressure Washer

Operator’s Manual

Model Number _____________________________

Revision __________________________________

Serial Number ______________________________

Date Purchased ____________________________

BRIGGSandSTRATTON.COM

(800) 743-4115

Table of Contents

Symbols and Meanings ...........................2

Equipment Description............................3

Features and Controls ............................4

Operation.......................................6

Maintenance ...................................12

Storage .......................................15

Troubleshooting.................................16

Specifications ..................................17

Warranty ......................................18

To ensure prompt and complete warranty coverage, register

your product online at www.onlineproductregistration.com.

Symbols and Meanings

Signal Meaning

DANGER

Indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING

Indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE

Indicates information considered

important, but not hazard-related.

Symbol Name Explanation

Safety Alert

Symbol

Indicates a potential personal

injury hazard.

Read

Operator’s

Manual

Failure to follow warnings,

instructions and operator’s

manual could result in death or

serious injury.

Toxic Fumes

Engine exhaust contains carbon

monoxide, a poisonous gas that

could kill you in minutes. You

cannot smell it or see it.

Fire

Fuel and its vapors are extremely

flammable which could cause

burns or fire resulting in death or

serious injury.

Engine exhaust could cause

fire resulting in death or serious

injury.

Symbol Name Explanation

Fluid

Injection

High-pressure water could cut

through skin resulting in serious

injury and possible amputation.

Spray,

Flying

Objects

Risk of eye injury. Spray could

splash back or propel objects

resulting in serious injury.

Hot Surface

Contact with muffler area could

cause burns resulting in serious

injury.

Electric

Shock

Contact with power source

could cause electrical shock

resulting in death or serious

injury.

Kickback

Recoil starter kickback will pull

hand and arm toward engine

faster than you can let go which

could cause broken bones,

sprains or bruises resulting in

serious injury.

Chemical

Burn

Chemicals could cause burns

resulting in death or serious

injury.

Slippery

Surface/Fall

Slippery wet surfaces could

cause you to fall resulting in

death or serious injury.

Fall

Kickback from spray gun could

cause you to fall resulting in

death or serious injury.

WARNING! This product can expose you to

chemicals including gasoline engine exhaust, which

is known to the State of California to cause cancer,

and carbon monoxide, which is known to the State of

California to cause birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

WARNING! This product contains lead and lead

compounds, known to the state of California to

cause birth defects or other reproductive harm.

Wash your hands after handling this product. Cancer and

Reproductive Harm - www.P65Warnings.ca.gov

2 BRIGGSandSTRATTON.COM

Air Cleaner — Filters engine intake air.

Engine Identification — Provides model, type and code of

engine.

Fuel Cap — Add unleaded fuel here.

High Pressure Hose — Connect one end to water pump

and the other end to spray gun.

High Pressure Outlet — Connection for high pressure hose.

Identification Label — Provides model and serial number of

pressure washer.

Oil Fill/Dipstick — Check, ll and drain oil here.

Pump — Stainless steel piston, axial cam pump that

develops high pressure.

Recoil Starter — Used to start the engine.

Water Inlet — Connection for garden hose.

Equipment Description

Read this manual carefully and become familiar

with your product. Know its applications, its

limitations, and any hazards involved. Save these

original instructions for future reference.

To aid in outdoor cleaning projects, this engine-driven,

high-pressure cleaning machine uses a variety of spray

patterns and detergent.

Know how to stop the product and reduce pressure quickly.

Keep operating area clear and do not allow children to

operate pressure washer.

Stay alert—watch what you are doing. Do not operate

pressure washer when fatigued or under the influence of

alcohol or drugs.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter, or otherwise improve the product

and this document at any time without prior notice.

NOTICE If you have questions about intended use,

contact an authorized service dealer. This equipment is

designed to be used with Briggs & Stratton

authorized

parts only.

This spark ignition system complies with the Canadian

Standard CAN ICES-2/NMB-2.

Recoil Starter

Oil Fill/Dipstick

Engine Identication

Fuel Cap

Pump

Water Inlet

Identication Label

Air Cleaner

High Pressure Hose

High Pressure Outlet

Features and Controls

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and

product warnings.

Read and follow Operating Instructions

before running or servicing engine.

Gasoline is flammable. Allow engine to

cool at least 2 minutes before refueling.

Engines emit carbon monoxide,

DO NOT run in enclosed area.

4 BRIGGSandSTRATTON.COM

Accessory Tray

Accessory Tray — Provides convenient storage for

accessories.

Automatic Cool Down System — Prevents internal

pump damage by discharging warm water to the

ground.

Detergent Siphoning Tube — Use to siphon pressure

washer safe detergents into the low pressure stream.

Engine Switch — Set switch to ON (I) before starting

engine. Set switch to OFF (0) to shut o engine.

Spray Wand — Allows you to switch between 7-in-1

nozzle and optional accessories.

Spray Gun — Controls spray using trigger. Includes

trigger lock.

7-in-1 Nozzle — Multiple patterns for various cleaning

applications.

7-in-1 Nozzle

Engine Switch

Spray Wand

Spray Gun

Automatic Cool

Down System

Detergent

Siphoning Tube

Risque d’incendie. L’utilisation de ce dispositif peut créer

des étincelles qui peuvent déclencher un incendie dans les

endroits de végétation sèche. L’installation d’un

pare-étincelles

peut être nécessaire. L’opérateur doit contacter le service

d’incendie local pour les lois et règlements concernant

les exigences de prévention d’incendie.

318602

PowerFlow+ Technology™

One easy twist. 7 ways to clean.

PowerFlow+ technology provides both high pressure to lift

dirt and high flow to easily wash it away. The high flow mode

enhances the cleaning experience by providing extended

reach, power soaping, and faster rinsing capabilities – things

standard pressure washers can’t do.

The force behind PowerFlow+ is in the pump with two

separate cleaning modes, high pressure and high flow.

These dual modes can easily be changed via the 7-in-1

nozzle without changing nozzle tips. The high pressure

mode delivers up to 2800 PSI (pounds square inch) (Model

020770) or up to 3100 (pounds square inch) (Model 020771

& 020772) and is ideal for cleaning the toughest stains,

mildew, and grime from decks, driveways, and siding. The

high flow mode delivers up to 3.5 GPM (gallons per minute)

(Model 020770) or up to 4.5 GPM (gallons per minute)

(Model 020771 & 020772) to power-rinse away dirt, soap,

and debris. The high flow mode is also great for washing

delicate surfaces such as patio furniture, vehicles, and

children’s outdoor play sets and toys.

Operation

Step 1: Safe Location

Before starting the pressure washer, there are two equally

important safety concerns regarding carbon monoxide

poisoning and fire that must be addressed.

Operation Location to Reduce the Risk of Carbon

Monoxide Poisoning

The engine exhaust of all fossil fuel burning equipment,

such as a pressure washer, contains carbon monoxide, a

poisonous gas that could kill you in minutes. You cannot

smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

By law, it is required in many states to have a carbon

monoxide alarm in operating condition in your home.

A carbon monoxide alarm is an electronic device that

detects hazardous levels of carbon monoxide. When there

is a buildup of carbon monoxide, the alarm will alert the

occupants by flashing a visual indicator light and an alarm.

Smoke alarms cannot detect carbon monoxide gas.

WARNING! Engine exhaust contains carbon

monoxide, a poisonous gas that could kill you in

minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

• Operate this product only outdoors, far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas accumulating and the potential of being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• Do not run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors and

windows for ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for hours, even

after this product has shut off.

• Point exhaust away from all homes and occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air right away. See a doctor. You may

have carbon monoxide poisoning.

Carbon monoxide alarm

Install carbon monoxide alarms inside

your home. Without working carbon

monoxide alarms, you may not realize

you are getting sick and dying from

carbon monoxide poisoning.

CARBON MONOXIDE AL

ARM(S)

USE OUTDOORS - AVOID CARBON MONOXIDE POISONING

point away fr

om home

MUFFLER

6 BRIGGSandSTRATTON.COM

Operation Location to Reduce the Risk of Fire

WARNING! Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a fire, resulting in death or serious injury.

• Pressure washer must be at least 5 ft (1.5 m) from any

structure, overhang, trees, windows, doors, and any wall

opening, shrubs, or vegetation over 12 in. (30.5 cm) in

height.

• Do not place pressure washer under a deck or other type

of structure that may confine airflow. Smoke alarm(s)

must be installed and maintained indoors according to the

manufacturer’s instructions /recommendations.

• Carbon monoxide alarms cannot detect smoke.

• It is a violation of California Public Resource Code Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined

in Section 4442, maintained in effective working order.

Other states or federal jurisdictions may have similar laws,

reference Federal Regulation 36 CFR Part 261.52.

• Contact the original equipment manufacturer, retailer, or

dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

Step 2: Oil and Fuel

Check Oil Level

CAUTION! Avoid prolonged or repeated skin

contact with used motor oil. Used motor oil has

been shown to cause skin cancer in certain

laboratory animals. Thoroughly wash exposed areas with

soap and water.

1. Make sure pressure washer is on a level surface.

2. Clean the oil fill area of any debris.

3. Remove oil dipstick and wipe dipstick with clean cloth.

Replace and tighten dipstick. Remove and check oil

level.

4. Verify oil is at full mark (top hole) on dipstick. Replace

and tighten dipstick.

5. If needed, see Maintenance section for instructions to

add oil.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded fuel with a minimum of 87 octane.

• Gasoline with an ethanol content up to 10% is acceptable.

NOTICE Do not mix oil in fuel or modify engine to run on

alternate fuels. Unapproved fuels could damage engine.

See High Altitude for operation above 5,000 ft. (1524 m).

WARNING! Fuel and its vapors are extremely

flammable which could cause burns or fire

resulting in death or serious

injury.

• Do not refuel during operation.

• Do not smoke during refueling.

• Turn engine off and let it cool at least 2 minutes before

removing fuel cap.

• Fill fuel tank outdoors. Keep fuel away from ignition

sources.

Full

Add

MUFFLER

5 ft (1.5 m)

min.

5 ft (1.5 m) min.

E15

E10

1. Slowly remove fuel cap to relieve pressure in tank.

2. Slowly add fuel to fuel tank. Do not fill above bottom of

fuel tank neck to allow for fuel expansion.

3. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At altitudes over 5,000 ft (1524 m), a minimum 85 octane

fuel is acceptable. To remain emissions compliant, high

altitude adjustment is required. Operation without this

adjustment will cause decreased performance, increased

fuel consumption, and increased emissions.

See an authorized Briggs & Stratton dealer for high altitude

adjustment information. Operation of the engine at altitudes

below 2,500 ft (762 m) with the high altitude kit is not

recommended.

Transporting

Do not tip engine or equipment at an angle which causes

fuel to spill.

Step 3: Set Up

Clean Debris

Clean any accumulated debris. Keep area around muffler

free from any debris.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a damp cloth to wipe exterior surfaces clean.

Lubricate O-rings

Lubricate all connections shown to extend the life of the

o-rings.

1. Inspect and clean connecting surfaces prior to

lubrication and assembly. Replace o-rings that are

damaged or missing. See Common Service Parts.

NOTICE Never repair leaking connections with sealant of

any kind. Replace o-ring.

2. Use a small brush or cotton swab to apply a light

coating of grease directly to o-rings.

Check / Connect Gun and Hose

1. If spray gun trigger depresses without pressing

trigger lock or if spray gun remains depressed when

released, replace spray gun immediately.

2. If high pressure hose is damaged, exposing inner

mesh, replace immediately.

3. Attach high pressure hose to spray gun and high

pressure outlet on pump. Tighten by hand.

WARNING! The high pressure fluid could cut

through skin and its underlying tissues, resulting

in serious injury and possible amputation. Never

attach spray wand directly to high pressure hose.

Maximum Fill Level

Trigger Lock

Spray Gun

High

Pressure

Hose

Spray Wand

8 BRIGGSandSTRATTON.COM

Check Water Inlet Screen / Connect Garden Hose

1. Inspect inlet screen. Remove debris or replace if

damaged.

2. Run water through garden hose (not to exceed 50 ft

(15 m) to clean out debris, then connect to water inlet.

NOTICE There must be at least 10 ft (3 m) of unrestricted

garden hose between the pressure washer inlet and

any device, such as a vacuum breaker, to prevent pump

damage.

3. Turn on water, point spray gun in safe direction, press

trigger lock and depress trigger to purge pump system

of air.

4. Attach spray wand to spray gun. Tighten by hand.

Step 4: 7-in-1 Nozzle

1. Select desired nozzle setting:

2. Pull spray wand quick connect collar back, insert 7-in-

1 nozzle and release. Tug nozzle to ensure it is secure.

Inlet Screen

High Pressure:

HIgh Flow:

Step 5: Start Up

NOTICE Do not start engine without water supply

connected and turned on.

1. Level product before starting.

2. Push engine switch to ON (I) position.

WARNING! Risk of eye injury. Spray could

splash back or propel objects, resulting in

serious injury.

• Always wear indirect vented (chemical splash) safety

goggles when using or near this product. (Safety glasses

do not provide full protection).

• Always wear protective clothing such as long-sleeved

shirts, long pants and closed-toed shoes.

WARNING! Recoil starter kickback (rapid

retraction) will pull hand and arm toward engine

faster than you can let go, which could cause

broken bones, fractures, bruises, or sprains and result in

serious injury.

NOTICE A ReadyStart® engine requires no priming or

choking.

3. Position yourself as shown below, grasp recoil starter

and pull slowly until you feel some resistance. Then

pull rapidly to start engine.

4. Return recoil starter slowly. Do not let rope “snap back”

against starter.

WARNING! High-pressure water could cut

through skin resulting in serious injury and

possible amputation.

• Do not direct discharge at self or others.

• Call physician immediately if cut by fluid. Do not treat as

a simple cut.

• Do not touch 7-in-1 nozzle while spraying.

WARNING! Use of pressure washer

could create slippery surfaces causing

you to fall, resulting in death or serious

injury. Kickback from spray gun could cause you to fall

resulting in death or serious injury. Operate pressure

washer from a stable surface.

5. Firmly grasp spray gun with both hands, point spray

gun in safe direction, press trigger lock and depress

trigger to begin spraying.

6. Apply high pressure spray to a small area first, then

check the surface for damage. If no damage is found,

it is okay to continue cleaning.

WARNING! Risk of electrocution. Contact with

power source could cause electric shock or burn

resulting in death or serious injury. Never spray

near power source.

NOTICE Pressure washer may be equipped with an

automatic idle control that lowers engine speed when spray

gun trigger is released.

Engine Switch

10 BRIGGSandSTRATTON.COM

Usage Tips

• For most effective cleaning when in High Pressure,

keep 7-in-1 nozzle 8 to 24 in (20 to 61 cm) away from

cleaning surface.

• Do not use high pressure 7-in-1 nozzle, especially a

high pressure spray pattern nozzle, closer than 6 in (15

cm) to prevent damage to the cleaning surface.

• Start at the top of the area to be rinsed, working down

with long, even, overlapping strokes.

Step 6: Applying Detergent

WARNING! Chemicals could cause burns

resulting in death or serious injury.

• Follow chemical manufacturer’s label instructions for

proper use and handling of the chemical.

• Only use products marketed for use with pressure

washers.

• Never spray flammable liquids.

Check Detergent Siphoning Tube

Clean detergent tube if clogged or replace if leaking.

To apply detergent, follow these steps:

1. Attach detergent siphon tube to the barbed fitting on

the pump.

2. Prepare pressure washer detergent per manufacturer’s

instructions.

3. Place detergent siphoning tube into detergent

container making sure end is fully submerged while

applying detergent.

4. Select desired soap setting on 7-in-1 nozzle. See

7-in-1 Nozzle.

5. Apply per manufacturer’s instructions.

NOTICE Detergent cannot be applied with non soap

nozzle setting.

Step 7: Shut Down

1. Release spray gun trigger and let engine idle for one

minute.

2. Push engine switch to OFF (0) position.

WARNING! Spray gun traps high water

pressure, even after engine shut down and water

disconnection, which could result in serious injury.

3. Point spray gun in safe direction. Press trigger lock

and depress trigger to relieve high water pressure.

Step 8: Clean Up

1. Turn off water and purge system.

2. Disconnect and drain all hoses, spray gun and spray

wand.

3. Empty pump of all liquids by pulling recoil handle

about six times.

NOTICE If storing in freezing temperatures or more than

30 days, see Storage.

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first.

Service more often under dirty or dusty conditions.

See any authorized dealer for service.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the pressure washer. See any authorized

dealer for service.

Pump Oil

Do not attempt any oil maintenance on this pump. The

pump is pre-lubricated and sealed from the factory,

requiring no additional maintenance for the life of the pump.

Detergent Siphoning Check Ball

The check ball in detergent siphoning system may become

stuck from dried soap or minerals in water. The check ball

can be freed by performing the following:

WARNING! Chemical Burn Hazard. Chemicals

could cause burns resulting in death or serious

injury. Follow chemical manufacturer’s label

instructions for proper use and handling of the chemical.

Following Shut Down, remove detergent siphoning hose

from barbed fitting on pump and drain detergent into a

container.

1. Insert paper clip, or similar device, into barbed fitting

on pump and push down until ball moves.

2. Reinstall detergent siphoning hose.

7-in-1 Nozzle Maintenance

Clean an obstructed nozzle to correct a pulsing sensation

when squeezing the spray gun trigger.

1. Following Shut Down, remove 7-in-1 nozzle from spray

wand.

2. Use a paper clip, or similar device, to free foreign

material.

Every 8 Hours or Daily (see Operation Section)

• Check engine oil level

• Clean debris

• Lubricate o-rings

• Check spray gun

• Check high pressure hose

• Check / clean water inlet screen

• Check detergent siphoning tube

Every 50 Hours or Yearly

• Clean air cleaner

• Inspect muffler and if equipped, spark arrester

Every 200 Hours or Yearly

• Replace engine air cleaner

Yearly

• Replace spark plug

• Clean cooling system

1, 2

12 BRIGGSandSTRATTON.COM

Engine Maintenance

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain “no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See the Emissions Warranty.

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity

for the engine. Use the chart to select the best viscosity

for the outdoor temperature range expected. Engines on

most outdoor power equipment operate well with 5W30

Synthetic oil. For equipment operated in hot temperatures,

Vanguard

15W50 Synthetic oil provides the best

protection.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°F) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

Add Engine Oil

1. Place pressure washer on level surface.

2. Clean area around oil fill and remove yellow oil fill cap/

dipstick.

3. Slowly pour oil into oil fill opening. Checking oil level

frequently, fill to full mark (top hole) on dipstick.

NOTICE Pause to permit oil to settle. Wipe dipstick clean

each time oil level is checked. Do not overfill.

4. Replace and tighten dipstick.

5. Wipe up any remaining oil.

NOTICE Do not attempt to start engine before it has been

properly serviced with oil. This could result in engine failure.

CAUTION! Avoid prolonged or repeated skin

contact with used motor oil. Used motor oil has

been shown to cause skin cancer in certain

laboratory animals. Thoroughly wash exposed areas with

soap and water.

KEEP OUT OF REACH OF CHILDREN. DO NOT

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Change Engine Oil

An oil change is not required. Follow the steps below if you

want to change the oil.

Change oil while engine is still warm from running, as

follows:

1. Drain fuel tank by running pressure washer until fuel

tank is empty.

2. Disconnect spark plug wire and keep it away from

spark plug.

3. Clean area around oil fill, remove oil fill cap/dipstick.

Wipe dipstick clean.

WARNING! Contact with muffler area could

cause burns resulting in serious injury. Lift by

frame when tipping to avoid hot surfaces.

4. Tip pressure washer to drain oil from oil fill into a

suitable container making sure to tip unit away from

spark plug.

5. When engine is empty, return pressure washer to

upright position.

6. Add recomended oil as described in Add Engine Oil.

7. Reconnect spark plug wire to spark plug.

Full

Add

Service Air Cleaner

WARNING! Fuel and its vapors are extremely

flammable, which could cause burns or fire,

resulting in death or serious injury.

• Do not start and run engine with air filter removed.

Your engine will not run properly and may be damaged if

you run it with a dirty or missing air cleaner.

1. Pull the latch and open the cover.

2. Carefully remove air cleaner to prevent debris from

falling into carburetor.

Model 020770

3. To loosen debris, gently tap the air cleaner on a hard

surface. If the air cleaner is excessively dirty, replace

with a new air cleaner.

4. Reinstall clean or new air cleaner in base.

5. Close the cover and secure the latch.

Model 020771 & 020772

3. Wash foam air cleaner in liquid detergent and water.

Squeeze dry in a clean cloth.

4. Saturate foam air cleaner in new engine oil and

squeeze in a clean cloth to remove excess oil.

5. Reinstall clean or new air cleaner in base.

6. Close the cover and secure the latch.

Service Spark Plug

Changing the spark plug will help your engine to start

easier and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Replace spark plug if electrodes are pitted, burned

or porcelain is cracked. Use the recommended

replacement spark plug. See Common Service Parts.

4. Check electrode gap with wire feeler gauge and reset

spark plug gap to recommended gap if necessary

(see Specifications).

5. Install spark plug and tighten firmly.

Inspect Muffler and Spark Arrester

Inspect the muffler for cracks, corrosion, or other damage.

Remove the spark arrester, if equipped, and inspect for

damage or carbon blockage. Clean if carbon blockage is

found using brush and commercial solvent or replace if

damaged.

WARNING! Contact with muffler area could

cause burns resulting in serious injury. Do not

touch hot parts.

Common Service Parts

Pump Saver™ ............................6039

O-ring Maintenance Kit ...................705001

Water Inlet Screen .....................B2384GS

Engine Oil Bottle ...............100005 or 100028

Air Cleaner (Model 020770) ...............593260

Spark Plug (Model 020770) ...............594056

Air Cleaner (Model 020771 & 020772) ......595297

Spark Plug (Model 020771 & 020772) .......594264

Contact an authorized service dealer or

BRIGGSandSTRATTON.com for a full list of parts and

diagrams.

Latch

Air Cleaner

Cover

Air Cleaner

Latch

Cover

14 BRIGGSandSTRATTON.COM

Storage

WARNING! Fuel and its vapors are extremely

flammable, which could cause burns or fire,

resulting in death or serious injury. Do not store fuel

near ignition source.

1. Place detergent siphon tube in water and flush

detergent from system by running pressure washer

with one of the soap nozzles selected.

Protecting Fuel System

2. Treat or drain fuel from pressure washer as fuel can

become stale when stored over 30 days.

Each time you fill the container with fuel, add STA-BIL

360°® PROTECTION™ to the fuel as specified by the

manufacturer’s instructions. This keeps fuel fresh and

decreases fuel-related problems or contamination in the

fuel system.

It is not necessary to drain fuel from the engine when STA-

BIL 360°® PROTECTION™ is added as instructed. Before

storage, turn the engine ON for 2 minutes to move the fuel

and stabilizer through the fuel system.

If fuel in the engine has not been treated with STA-

BIL 360°® PROTECTION™, it must be drained into an

approved container. Then run the engine until it stops from

lack of fuel.

Protecting the Pressure Washer

3. Turn off water and purge system.

4. Disconnect and drain all hoses, spray gun and spray

wand.

5. Empty pump of all liquids by pulling recoil handle

about six times.

NOTICE Store spray gun indoors and keep from freezing.

Protecting the Pump

6. Treat pump with Pump Saver.

Use Pump Saver to protect pump from damage caused by

mineral deposits and freezing. It also lubricates pistons and

seals. See Common Service Parts.

Read and follow all Pump Saver warnings and instructions.

If Pump Saver is not available, connect a 3 ft (1 m)

section of garden hose to water inlet. Pour RV-antifreeze

(antifreeze without alcohol) into hose. Pull recoil handle

twice. Disconnect hose.

NOTICE You must protect your product from freezing

temperatures. Failure to do so will permanently damage

your pump and spray gun rendering your product

inoperable.

7. Store unit in a clean and dry area.

WARNING! Storage covers could cause a fire

resulting in death or serious injury. Do not place a

storage cover over a hot pressure washer. Let

product cool before installing cover.

Troubleshooting

Problem Cause Correction

Pump has following

problems: failure to

produce pressure, loss

of pressure, low water

volume.

1. High flow spray pattern selected.

2. Inadequate water supply.

3. Clogged inlet hose screen.

4. 7-in-1 nozzle is obstructed.

5. Connections leak.

6. High pressure hose or spray gun

leaks.

1. Select high pressure spray pattern.

2. Provide adequate water flow.

3. Check and clean inlet hose screen.

4. Clean nozzles. See 7-in-1 Nozzle

Maintenance.

5. Tighten connections or replace o-rings.

6. Replace.

Detergent fails to mix

with spray.

1. High pressure or high flow without

soap nozzle is selected.

2. Check ball stuck in detergent

siphoning system.

3. Detergent siphoning tube is clogged

or cracked.

1. Select a high flow soap nozzle setting

(indicated with bubbles).

2. Free check ball. See Detergent Siphoning

Check Ball.

3. Clean or replace detergent siphoning tube.

Engine will not start;

starts and runs rough

or shuts down during

operation.

1. Engine switch set to OFF (0) position.

2. Out of fuel.

3. Flooded with fuel.

4. Dirty air cleaner.

5. Spark plug wire not connected to

spark plug.

1. Set engine switch to ON (I) position.

2. Fill fuel tank.

3. Wait 5 minutes before starting.

4. Clean or replace air cleaner.

5. Connect wire to spark plug.

Idle control (if

equipped) not

functioning.

Idle control cable is loose. Contact local service facility.

For all other issues, see a Briggs & Stratton authorized dealer.

16 BRIGGSandSTRATTON.COM

Specifications

Model 020770

High Pressure Nozzles 2800 PSI (193 bar) @ 1.8 GPM (6.8 L/min)*

High Flow Nozzles 3.5 GPM (13.25 L/min)* @ 150 PSI (10.3 bar)

Water Supply Temperature 41°F (5°C) - 100°F (38°C)

min Water Supply Flow Rate 4.5 GPM (17 L/min)

min Water Supply Pressure 20 PSI (1.38 bar)

Engine Displacement 9.93 in

(163 cc)

Spark Plug Gap 0.030 in. (0.76 mm)

Oil Capacity 16 oz (0.5 L)

Model 020771 & 020772

High Pressure Nozzles 3100 PSI (214 bar) @ 2.1 GPM (7.6 L/min)*

High Flow Nozzles 4.5 GPM (17 L/min)* @ 150 PSI (10.3 bar)

Water Supply Temperature 41°F (5°C) - 100°F (38°C)

min Water Supply Flow Rate 5.5 GPM (20.8 L/min)

min Water Supply Pressure 20 PSI (1.38 bar)

Engine Displacement 11.58 in

(190 cc)

Spark Plug Gap 0.020 in. (0.050 mm)

Oil Capacity 20 oz (0.6 L)

Power Ratings: The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive

Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are

derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are derived at

3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and air

cleaner installed whereas gross power values are collected without these attachments. Actual gross engine power will be higher than net

engine power and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given the wide array

of products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given piece of power

equipment. This difference is due to a variety of factors including, but not limited to, the variety of engine components (air cleaner, exhaust,

charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and

engine-to engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power

for this engine.

*This pressure washer is rated in accordance to the Pressure Washer Manufacturers’ Association (PWMA) standard PW101-2010

(Testing and Rating Performance of Pressure Washers).

80082391_EN Rev -

BRIGGS & STRATTON WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship

or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for

and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSANDSTRATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for

inspection and testing.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the

warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion is

permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may

also have other rights which vary from state to state or country to country.**

WARRANTY PERIOD

* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related components

are covered by the Emissions Warranty Statement.

** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be

of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to salesenquires@briggsandstratton.com.au, Briggs & Stratton Australia Pty Ltd, 1

Moorebank Avenue, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail

consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial use,

it shall thereafter be considered as a commercial use product for purposes of this warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the

product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.

ABOUT YOUR WARRANTY

Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not cover

damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s

Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the

product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical

corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or

repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.

Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal

use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are

not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.

Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or

equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.

Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.

Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in

place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or

engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.

Item Consumer Use Commercial Use

Equipment 24 months 3 months

Engine* 24 months 3 months

Frame 36 months 3 months

18 BRIGGSandSTRATTON.COM

Limpiadora a presión

Manual del operador

Número de modelo __________________________

Revisión __________________________________

Número de serie ____________________________

Fecha de compra ___________________________

Milwaukee, WI, USA. Reservados todos los derechos.

(800) 743-4115

BRIGGSandSTRATTON.COM

Índice de contenidos

Símbolos y sus significados........................2

Descripción del equipo............................3

Características y controles.........................4

Operación ......................................6

Mantenimiento .................................12

Almacenamiento................................15

Solución de problemas...........................16

Especificaciones................................17

Garantía.......................................18

Registrar su producto

Para asegurar pronta y completa cobertura de

la garantía, registre su producto en línea en

www.onlineproductregistration.com.

Símbolos y sus significados

Señal Significado

PELIGRO

Indica un riesgo que, si no se evita,

ocasionará la muerte o lesiones graves.

ADVERTENCIA

Indica un riesgo que, si no se evita, podría

ocasionar la muerte o lesiones graves.

ATENCIÓN

Indica un riesgo que, si no se evita,

podría ocasionar lesiones menores o

moderadas.

AVISO

Indica una información que se considera

importante pero que no está relacionada

con un peligro potencial.

Símbolo Nombre Explicación

Símbolo de

alerta de

seguridad

Indica un posible riesgo para su

integridad física.

Lea el

Manual del

operador

La omisión de las advertencias,

las instrucciones y el manual

del operador podría redundar

en lesiones graves o incluso la

muerte.

Gases

tóxicos

La descarga de escape del

motor contiene monóxido de

carbono, un gas tóxico que

puede matar en minutos. No

puede olerse ni verse.

Incendio

El combustible y sus vapores

son extremadamente

inflamables, lo que podría

causar quemaduras o incendios

que resulten en lesiones graves

o la muerte.

El escape del motor puede

causar un incendio y ocasionar

lesiones graves o la muerte.

Símbolo Nombre Explicación

Inyección

de fluido

La alta presión de agua puede

cortar la piel y causar heridas

graves y posible amputación.

Spray,

objetos

que salen

volando

Riesgo de lesión ocular. El

agua rociada podría salpicar o

expulsar objetos, lo que puede

provocar lesiones graves.

Superficie

caliente

El contacto con el área

del mofle podría provocar

quemaduras y causar lesiones

graves.

Descarga

eléctrica

El contacto con los cables

eléctricos podría provocar

choque eléctrico y ocasionar

lesiones graves o la muerte.

Retroceso

El contragolpe del cable del

arrancador retráctil jalará la

mano y el brazo hacia el motor

más rápido de lo que usted

pueda soltarlo, lo que puede

causar huesos rotos, esguinces

o hematomas que resulten en

lesiones graves.

Quemadura

química

Los productos químicos

podrían causar quemaduras

que resulten en la muerte o en

lesiones graves.

Superficie

resbaladiza/

Caída

Superficies resbaladizas

mojadas podrían provocar

caídas que resulten en la

muerte o en lesiones graves.

Caída

El retroceso de la pistola puede

hacerle caer, lo que puede

ocasionarle la muerte o una

lesión grave.

¡ADVERTENCIA! Este producto puede

exponerlo a sustancias químicas, entre las que

se incluyen emisiones de escape de motor de

gasolina, reconocidas por el Estado de California como

causantes de cáncer, y monóxido de carbono, reconocido

por el Estado de California como causante de defectos de

nacimiento u otros problemas reproductivos. Para obtener

más información, visite www.P65Warnings.ca.gov.

¡ADVERTENCIA! Este producto contiene plomo

y compuestos de plomo que, de acuerdo al

estado de California, pueden causar defectos de

nacimiento u otros problemas reproductivos. Lávese las

manos después de manipular este producto. Cáncer y

Problemas Reproductivos – www.P65Warnings.ca.gov

2 BRIGGSandSTRATTON.COM

La page charge ...

Simplicity 020770-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020770-00

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 020770-00 User manual
español: Simplicity 020770-00 Manual de usuario

Documents connexes

Autres documents

Briggs & Stratton 5436 Information produit