Wacker Neuson DPU 130Le Manuel utilisateur

Operator's manual

Vibratory plate

Plaque vibrante

DPU 130Le

Notice d'emploi

5000193487 06 0811

5000193487

EN-FR

Manufacturer

Wacker Neuson Produktion GmbH & Co. KG

Preußenstraße 41

80809 München

www.wackerneuson.com

Tel.: +49-(0)89-354 02-0

Fax: +49-(0)89-354 02-390

Translation of the original operator's manual in German

08.2011

0215560en / 006

DPU 130Le

Operator's manual 3

1 Foreword ....................................................................................................................6

2 Introduction ...............................................................................................................7

2.1 Means of representation for this operator's manual ........................................... 7

2.2 Wacker Neuson representative .......................................................................... 8

2.3 Nameplate .......................................................................................................... 8

2.4 Indication of location........................................................................................... 9

3 Safety .......................................................................................................................10

3.1 Principle............................................................................................................ 10

3.2 Qualification of the operating personnel........................................................... 13

3.3 Protective gear ................................................................................................. 14

3.4 Transport .......................................................................................................... 15

3.5 Operating safety ............................................................................................... 16

3.6 Safety during the operation of vibratory plates................................................. 18

3.6.1 Safety when operating remote-controlled machines ............................ 19

3.7 Safety during the operation of combustion engines ......................................... 20

3.8 Safety during the operation of hydraulic machines........................................... 22

3.9 Maintenance..................................................................................................... 22

3.10 Safety and information labels ........................................................................... 24

3.11 Safety devices .................................................................................................. 27

4 Scope of delivery ....................................................................................................29

5 Structure and function ...........................................................................................30

5.1 Application........................................................................................................ 30

5.2 Description........................................................................................................ 30

5.2.1 Principle of the machine ....................................................................... 30

5.2.2 Remote control ..................................................................................... 31

5.2.3 Infrared system..................................................................................... 31

5.2.4 Receiving area and proximity area of the machine .............................. 32

5.2.5 Diagnostic system ................................................................................ 33

5.2.6 Machine configuration system .............................................................. 35

5.3 Functional description....................................................................................... 36

6 Components and operator's controls ...................................................................38

6.1 Components and operator's controls outside the machine .............................. 38

6.2 Components and operator's controls inside the machine................................. 39

6.3 Remote control components and operator's controls....................................... 43

Inhalt

DPU 130Le

4 Operator's manual

7 Transport ................................................................................................................. 45

7.1 Lifting the machine ........................................................................................... 46

8 Use and operation ................................................................................................... 49

8.1 Prior to starting the machine ............................................................................ 49

8.1.1 Checks before startup .......................................................................... 49

8.2 Starting up........................................................................................................ 51

8.3 Operating the machine ..................................................................................... 55

8.3.1 Machine's directions of movement ....................................................... 55

8.3.2 Note on the machine's directions of movement.................................... 56

8.3.3 Compacting on a slope......................................................................... 57

8.3.4 Moving and stopping the machine........................................................ 58

8.3.5 Turning on and off slow/fast operation ................................................. 58

8.3.6 Turning on/off stand vibration............................................................... 59

8.4 Decommissioning ............................................................................................. 60

8.5 Turning off the machine in an emergency (emergency stop) ........................... 62

8.6 Recharging remote control battery ................................................................... 62

8.6.1 Charging the battery with the coiled helix cable ................................... 62

8.6.2 Charging battery with external charger................................................. 64

8.7 Setting transmission channel ........................................................................... 66

8.8 Using the diagnostic menu ............................................................................... 69

8.9 Using the configuration menu........................................................................... 70

9 Maintenance ............................................................................................................71

9.1 Maintenance schedule ..................................................................................... 71

9.1.1 One-time maintenance after initial operation........................................ 71

9.1.2 Daily maintenance tasks....................................................................... 72

9.1.3 Regular maintenance ........................................................................... 72

9.2 Maintenance work ............................................................................................ 75

9.2.1 Cleaning machine and remote control.................................................. 75

9.2.2 Topping up with fuel ............................................................................. 75

9.2.3 Checking motor oil level and topping up engine oil .............................. 77

9.2.4 Changing the engine oil........................................................................ 78

9.2.5 Checking/cleaning/replacing air cleaner............................................... 80

9.2.6 Checking coolant level and topping up coolant .................................... 82

9.2.7 Checking exciter oil level and topping up exciter oil............................. 84

9.2.8 Checking hydraulic oil level and refilling hydraulic oil........................... 86

DPU 130Le

Operator's manual 5

10 Troubleshooting ......................................................................................................88

10.1 Procedure in case of malfunctions ................................................................... 88

10.2 Machine malfunctions....................................................................................... 89

10.3 Malfunction messages of the receiver units ..................................................... 90

10.4 Malfunction messages in the control lamps of the remote control.................... 91

10.5 Malfunction messages on the control lamps and the machine's display screen ...

92

10.6 Eliminating malfunctions................................................................................... 97

10.6.1 Jumpstart with a donor battery ............................................................. 97

11 Disposal ...................................................................................................................99

11.1 Disposal of batteries......................................................................................... 99

12 Accessories ...........................................................................................................100

12.1 Battery ............................................................................................................ 100

12.2 External charger ............................................................................................. 100

13 Technical data .......................................................................................................101

13.1 DPU 130Le..................................................................................................... 101

14 Appendix ................................................................................................................ 105

14.1 Display texts ................................................................................................... 105

15 Emission control systems information and warranty .......................................106

EC Declaration of Conformity ..............................................................................107

1 Foreword

6

1 Foreword

This operator's manual contains information and procedures for the safe opera-

tion and maintenance of your Wacker Neuson machine. In the interest of your

own safety and to prevent accidents, you should carefully read through the safety

information, familiarize yourself with it and observe it at all times.

This operator's manual is not a manual for extensive maintenance and repair

work. Such work should be carried out by Wacker Neuson service or authorized

specialists.

The safety of the operator was one of the most important aspects taken into con-

sideration when this machine was designed. Nevertheless, improper use or in-

correct maintenance can pose a risk. Please operate and maintain your Wacker

Neuson machine in accordance with the instructions in this operator's manual.

Your reward will be troublefree operation and a high degree of availability.

Defective machine parts must be replaced immediately!

Please contact your Wacker Neuson representative if you have any questions

concerning operation or maintenance.

No part of this publication may be reproduced in any form or by any means, elec-

tronic or mechanical, including photocopying, without the expressed written per-

mission of Wacker Neuson.

Any type of reproduction, distribution or storage on data media of any type and

form not authorized by Wacker Neuson represents an infringement of copyright

and will be prosecuted.

We expressly reserve the right to make technical modifications – even without

special notice – which aim at further improving our machines or their safety stan-

dards.

DPU 130Le 2 Introduction

Operator's manual 7

2 Introduction

2.1 Means of representation for this operator's manual

Warning symbols

This operator's manual contains safety information of the categories:

DANGER, WARNING, CAUTION, NOTICE.

They should be followed to prevent danger to life and limb of the operator or

damage to equipment and exclude improper service.

Notes

Note: Complementary information will be displayed here.

DANGER

This warning notice indicates immediate hazards that result in serious injury or

even death.

f Danger can be avoided by the following the actions mentioned.

WARNING

This warning notice indicates possible hazards that can result in serious injury

or even death.

f Danger can be avoided by the following the actions mentioned.

CAUTION

This warning notice indicates possible hazards that can result in minor injury.

f Danger can be avoided by the following the actions mentioned.

NOTICE

This warning notice indicates possible hazards that can result in material

damage.

f Danger can be avoided by the following the actions mentioned.

2 Introduction DPU 130Le

8 Operator's manual

Instructions

f This symbol indicates there is something for you to do.

1. Numbered instructions indicate that you have to carry out something in a defined

sequence.

 This symbol is used for lists.

2.2 Wacker Neuson representative

Depending on your country, your Wacker Neuson representative is your Wacker

Neuson service, your Wacker Neuson affiliate or your Wacker Neuson dealer.

You can find the addresses in the Internet at www.wackerneuson.com.

The address of the manufacturer is located at the beginning of this operator's

manual.

2.3 Nameplate

Nameplate position

Item Designation

1 Nameplate

DPU 130Le 2 Introduction

Operator's manual 9

Nameplate data

The nameplate lists information that uniquely identifies your machine. This

information is needed to order spare parts and when requesting additional

technical information.

f Enter the information of your machine into the following table:

2.4 Indication of location

Item Designation Your information

1 Group and type

2 Construction year

3 Machine no.

4 Version no.

5 Item no.

Item Designation

1 Front (receiver unit transparent)

2 Right

3 Rear (receiver unit red)

4Left

3 Safety DPU 130Le

10 Operator's manual

3Safety

3.1 Principle

State of the art

This machine has been constructed with state-of-the-art technology according to

the recognized rules of safety. Nevertheless, when used improperly, dangers to

the life and limb of the operator or to third persons or damage to the machine or

other materials cannot be excluded.

Proper use

The machine must only be used for the following purposes:

 Compaction of soils.

The machine may not be used for the following purposes:

 Compaction of intensely cohesive soils.

 Compaction of frozen soils.

 Compaction of hard, non-compactable soils.

 Compaction of soils that are not capable of bearing a load.

 Compaction of asphalt.

 Shaking in of paving stones.

Its proper use also includes the observance of all instructions contained in this

operator's manual as well as complying with the required service and

maintenance instructions.

Any other use is regarded as improper. Any damage resulting from improper use

will void the warranty and the liability on behalf of the manufacturer. The operator

assumes full responsibility.

DPU 130Le 3 Safety

Operator's manual 11

Structural modifications

Never attempt to modify the machine without the written permission of the

manufacturer. To do so will endanger your safety and the safety of other people!

In addition, this will void the warranty and the liability on behalf of the

manufacturer.

Especially the following are cases of structural modifications:

 Opening the machine and the permanent removal of components from

Wacker Neuson.

 Installing new components which are not from Wacker Neuson and not

equivalent to the original parts in design and quality.

 Installation of accessories which are not from Wacker Neuson.

It is no problem to install spare parts from Wacker Neuson.

It is no problem to install accessories that are available in the Wacker Neuson

product range of your machine. Please refer to the installation regulations in this

operator's manual.

Requirements for operation

The ability to operate the machine safely requires:

 Proper transport, storage and setup.

 Careful operation.

 Careful service and maintenance.

Operation

Operate the machine only as intended and only when in proper working

condition.

Operate the machine in a safety-conscious manner with all safety devices

attached and enabled. Do not modify or disable any safety devices.

Before starting operation, check that all control and safety devices are

functioning properly.

Never operate the machine in a potentially explosive environment.

Supervision

Never leave the machine running unattended!

Maintenance

Regular maintenance work is required in order for the machine to operate

properly and reliably over time. Failure to perform adequate maintenance

reduces the safety of the machine.

 Strictly observe the prescribed maintenance intervals.

 Do not use the machine if it requires maintenance or repairs.

3 Safety DPU 130Le

12 Operator's manual

Malfunctions

If you detect a malfunction, you must shut down and secure the machine

immediately.

Eliminate the malfunctions that impair safety immediately!

Have damaged or defective components replaced immediately!

For further information, refer to chapter Troubleshooting.

Spare parts, accessories

Use only spare parts from Wacker Neuson or such that are equivalent to the

original parts in design and quality.

Only use accessories from Wacker Neuson.

Non-compliance will exempt the manufacturer from all liability.

Exclusion of liability

Wacker Neuson will refuse to accept liability for injuries to persons or for damage

to materials in the following cases:

 Structural modifications.

 Improper use.

 Failure to comply with this operator's manual.

 Improper handling.

 Using of spare parts which are not from Wacker Neuson and not equivalent

to the original parts in design and quality.

 Using of accessories which are not from Wacker Neuson.

Operator's manual

Always keep the operator's manual near the machine or near the worksite for

quick reference.

If you have misplaced the operator's manual or require an additional copy,

contact your Wacker Neuson representative or download the operator's manual

from the Internet (www.wackerneuson.com).

Always hand over this operator's manual to other operators or to the future owner

of the machine.

Country-specific regulations

Observe the country-specific regulations, standards and guidelines in reference

to accident prevention and environmental safety, for example those pertaining to

hazardous materials and wearing protective gear.

Complement the operator's manual with additional instructions taking into

account the operational, regulatory, national or generally applicable safety

guidelines.

DPU 130Le 3 Safety

Operator's manual 13

Operator's controls

Always keep the operator's controls of the machine dry, clean and free of oil or

grease.

Operating elements such as ON/OFF switch, gas handles etc. may not be

locked, manipulated or changed without authorization.

Cleaning

Always keep the machine clean and be sure to clean it each time you have

finished using it.

Do not use gasoline or solvents. Danger of explosion!

Do not use high pressure washers. Permeating water can damage the machine.

When electrical equipment is present, this can pose a serious injury risk from

electric shocks.

Checking for signs of damage

Inspect the machine when it is switched off for any signs of damage at least once

per work shift.

Do not operate the machine if there is visible damage or defects.

Have any damage or defects eliminated immediately.

3.2 Qualification of the operating personnel

Operator qualifications

Only trained personnel are permitted to start and operate the machine. The

following rules also apply:

 You are at least 18 years of age.

 You are physically and mentally fit.

 You have received instruction on how to independently operate the machine.

 You have received instruction in the proper use of the machine.

 You are familiar with required safety devices.

 You are authorized to start machines and systems in accordance with the

standards governing safety.

 Your company or the operator has assigned you to work independently with

this machine.

Incorrect operation

Incorrect operation or misuse by untrained personnel can endanger the health

and safety of the operator or third persons and also cause machine and material

damage.

3 Safety DPU 130Le

14 Operator's manual

Operating company responsibilities

The operating company must make the operator's manual available to the

operator and ensure that the operator has read and understood it.

Work recommendations

Please observe the recommendations below:

 Work only if you are in a good physical condition.

 Work attentively, particularly as you finish.

 Do not operate the machine when you are tired.

 Carry out all work calmly, circumspectly and carefully.

 Never operate the machine under the influence of alcohol, drugs or

medication. This can impair your vision, reactions and your judgment.

 Work in a manner that does not endanger others.

 Ensure that no persons or animals are within the danger zone.

3.3 Protective gear

Work clothing

Clothing should be appropriate, i.e. should be close-fitting but not restrict your

movement.

When on construction sites, do not wear long hair loosely, loose clothing or

jewelry including rings. These objects can easily get caught or be drawn in by

moving machine parts.

Only wear clothing made of material that is not easily flammable.

Personal protective gear

Wear personal protective gear to avoid injuries or health hazards:

 Non-skid, hard-toed shoes.

 Work gloves made of durable material.

 Overalls made of durable material.

 Hard hat.

 Ear protection.

DPU 130Le 3 Safety

Operator's manual 15

Ear protection

This machine generates noise that exceeds the country-specific permissible

noise levels (individual rating level). It may therefore be necessary to wear ear

protection. You can find the exact value in the chapter Technical Data.

When wearing ear protection while working, you must pay attention and exercise

caution because your hearing is limited, e.g. in case someone screams or a

signal tone sounds.

Wacker Neuson recommends that you always wear ear protection.

3.4 Transport

Turning off engine and deactivating machine

Always turn off the engine and deactivate the machine before transport.

Let engine cool off.

Observing hazardous materials regulations

Observe the national safety guidelines and the hazardous materials regulations

that apply to the respective means of transportation.

Lifting

When lifting the machine, observe the following instructions:

 Designate a skilled person to guide you for the lifting procedure.

 You must be able to see or hear this person.

 Use only suitable and certified hoisting gear, lifting tackle and load-bearing

equipment with sufficient lifting capacities.

 Only use the attachment points described in the operator's manual.

 Attach the machine securely to the hoisting gear.

 Ensure that no one is nearby or under the machine.

 Do not climb onto the machine.

Loading the machine

Loading ramps must be able to bear the load and be in a stable position.

Make sure that no one can be endangered if the machine slips away or tips over

or if machine parts suddenly move upward or downward.

Put the operating controls and moving parts in their transport position.

Secure the machine with load-securing straps so that it cannot tip over, fall down

or slide away. Only use the attachment points described in the operator's

manual.

3 Safety DPU 130Le

16 Operator's manual

Transport vehicle

Use only suitable transport vehicles with sufficient load-carrying capacity and

suitable tie-down lugs.

Transporting the machine

Secure the machine on the transport device against tilting, falling or slipping.

Restarting

Machines, machine parts, accessories or tools that were detached for transport

purposes must be re-mounted and fastened before restarting.

Only operate in accordance with the operating instructions.

3.5 Operating safety

Explosible environment

Never operate the machine in a potentially explosive environment.

Work environment

Familiarize yourself with your work environment before you start work. This

includes e.g. the following items:

 Obstacles in the work and traffic area.

 Load-bearing capacity of the ground.

 The measures needed to cordon off the construction site from public traffic in

particular.

 The measures needed to secure walls and ceilings.

 Options available in the event of an accident.

Safety in the work area

When working with the machine especially pay attention to the following points:

 Electric lines or pipes in work area.

 Gas lines or water lines in the work area.

Starting the machine

Observe the safety information and warning notices located on the machine and

in the operator's manual.

Never attempt to start a machine that requires maintenance or repairs.

Start the machine as directed in the operator's manual.

DPU 130Le 3 Safety

Operator's manual 17

Vertical stability

Always ensure that the machine is vertically stable and cannot tip over, roll or

slide away.

Proper operator position

Do not leave the proper operator position while operating the machine.

The intended operator position is behind the machine at a distance of at least

5m.

Leaving the danger area

Injury may be caused by moving machines or flying materials.

Ensure that operators and other persons observe a minimum safety distance of

2 m from the machine.

Caution with movable parts

Keep your hands, feet and loose clothing away from moving or rotating machine

parts. Parts of your body being pulled in or crushed can cause serious injuries.

Turning off engine and deactivating machine

Turn off the engine and deactivate the machine and remote control in the

following situations:

 Before breaks.

 If you are not using the machine.

Store the machine in such a way that it cannot tilt, fall or slip.

Storage location

After operation, allow the machine to cool and then store it in a sealed-off, clean

and dry location protected against frost and inaccessible to children.

Not using starter sprays

Highly flammable starter sprays pose a fire hazard.

Do not use any starter sprays.

Starter sprays are highly flammable and can cause backfiring and engine

damage.

3 Safety DPU 130Le

18 Operator's manual

3.6 Safety during the operation of vibratory plates

Danger of falling over

Operate the machine so that it cannot tip over or fall down from bordered areas,

edges and steps.

Load-carrying capacity of the ground

Keep in mind that the load-carrying capacity of the earth to be compressed or

bed can be greatly reduced by the effects of vibration, for example near slopes.

Avoid crushing

When operating the machine, pay particular attention to avoid being squeezed

between the machine and an obstacle. Always look in the direction of travel!

Compacting on slopes

The following points must be observed if you plan to compact inclined surfaces

(slopes, escarpments):

 Always stand above the machine on a slope.

 Start at the bottom of a slope (slopes that can be easily managed in an

upward direction can be safely traveled in a downward direction also).

 Never stand in a position where the machine could possibly fall. A slipping or

tipping machine can cause serious injuries.

Not exceeding the maximum tilt position

 Do not exceed the maximum tilt position (see chapter Technical Data).

 Only operate the machine at maximum tilt for short periods of time.

If you exceed the maximum tilt, the engine lubrication system will fail and thus

inevitably damage important engine parts.

DPU 130Le 3 Safety

Operator's manual 19

Check the effects of vibration

Compacting work in the vicinity of buildings can lead to structural damage. For

this reason you must always check the possible effects of vibrations on

surrounding buildings in the run-up to work.

You must take the following points into special consideration when evaluating the

effects of vibration:

 Vibration behavior, sensitivity and resonance frequency of surrounding

buildings.

 Distance of the buildings from the vibrationsite (= worksite).

 Condition of the soil.

You may need to carry out measurements to determine the vibration speed.

You must also comply with the relevant guidelines and regulations, particularly

DIN 4150-3.

The foundation must also have sufficient load-bearing capacity to withstand the

compaction energy. In case of doubt involve a soil mechanics specialist in the

evaluation.

Wacker Neuson is not liable for any structural damage.

3.6.1 Safety when operating remote-controlled machines

Keeping remote control and receiver units clean

Always keep the remote control and receiver units of the machine dry, clean and

free of oil or grease.

The remote control and receiver units must be uncovered, and nothing may be

glued onto them.

Maintaining visual contact at all times

Always aim the remote control directly at the machine during operation and

maintain visual contact at all times.

Infrared signals can be reflected.

Under certain circumstances the machine can also be moved by pressing the

control lever and not aiming the remote control directly at the machine.

Using different transmission channels

In order to avoid unintentionally controlling other machines within the receiving

area, the machines must not be set to the same transmission channel. Risk of

serious injury due to crushing.

Set different transmission channels if required.

3 Safety DPU 130Le

20 Operator's manual

3.7 Safety during the operation of combustion engines

Checking for signs of damage

Check the engine while switched off for leaks and cracks in the fuel line, tank and

fuel cap at least once per work shift.

Do not operate the machine if there is visible damage or defects.

Have any damage or defects eliminated immediately.

Dangers during operation

Combustion engines can be dangerous, particularly during operation and when

refueling.

Read and follow all safety instructions. Otherwise there is a risk of personal injury

and/or damage to property!

Do not start the engine near spilt fuel or if you smell fuel – this may cause an

explosion!

 Remove the machine from such areas.

 Remove the spilt fuel immediately!

Not changing the engine speed

Do not change the preset engine speed, as this may cause engine damage.

Preventing fires

Open flames and smoking are strictly prohibited in the immediate vicinity of the

machine.

Make sure that waste, such as paper, dry leaves or grass do not accumulate

around the exhaust muffler. The waste materials may ignite.

La page charge ...

Wacker Neuson DPU 130Le Manuel utilisateur

Wacker Neuson DPU 130Le Manuel utilisateur

dans d''autres langues

Documents connexes