Pioneer DEH-3400UB Manuel utilisateur

Owner’s Manual

Mode d’emploi

Manuale d’istruzioni

Manual de instrucciones

Bedienungsanleitung

Handleiding

Руководство пользователя

CD RDS RECEIVER

AUTORADIO CD RDS

SINTOLETTORE CD RDS

REPRODUCTOR DE CD CON RECEPTOR RDS

CD RDS-EMPFÄNGER

CD RDS-ONTVANGER

CD RDS ПРИЕМНИК

DEH-3400UB

DEH-2400UB

English NederlandsDeutschEspañolItalianoFrançais Русский

Thank you for purchasing this PIONEER

product

To ensure proper use, please read through this

manual before using this product. It is especially

important that you read and observe WARN-

INGs and CAUTIONs in this manual. Please

keep the manual in a safe and accessible place for

future reference.

If you want to dispose this product, do not

mix it with general household waste. There is

a separate collection system for used elec-

tronic products in accordance with legislation

that requires proper treatment, recovery and

recycling.

Private households in the member states of the

EU, in Switzerland and Norway may return their

used electronic products free of charge to desig-

nated collection facilities or to a retailer (if you

purchase a similar new one).

For countries not mentioned above, please con-

tact your local authorities for the correct method

of disposal.

By doing so you will ensure that your disposed

product undergoes the necessary treatment, re-

covery and recycling and thus prevent potential

negative effects on the environment and human

health.

About this unit

The tuner frequencies on this unit are allocated

for use in Western Europe, Asia, the Middle

East, Africa and Oceania. Use in other areas

may result in poor reception. The RDS (radio

data system) function only operates in areas

with broadcasting RDS signals for FM stations.

CAUTION

This product is a class 1 laser product classi-

fied under the Safety of laser products, IEC

60825-1:2007, and contains a class 1M laser

module. To ensure continued safety, do not re-

move any covers or attempt to gain access to

the inside of the product. Refer all servicing to

qualified personnel.

CAUTION—CLASS 1M INVISIBLE LASER

RADIATION WHEN OPEN, DO NOT VIEW

DIRECTLY WITH OPTICAL INSTRUMENTS.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with

liquids.

! The Pioneer CarStereo-Pass is for use only in

Germany.

! Always keep the volume low enough to hear

outside sounds.

! Avoid exposure to moisture.

! If the battery is disconnected or discharged,

any preset memory will be erased.

Note

Function setting operations are completed even

if the menu is cancelled before the operations

are confirmed.

About this manual

! In the following instructions, USB memories

and USB audio players are collectively re-

ferred to as “USB storage device”.

! In this manual, iPod and iPhone will be re-

ferred to as “iPod”.

Demo mode

Important

! Failure to connect the red lead (ACC) of this

unit to a terminal coupled with ignition

switch on/off operations may lead to battery

drain.

! Remember that if the feature demo contin-

ues operating when the car engine is turned

off, it may drain battery power.

The demo starts automatically if you do not oper-

ate this unit within about 30 seconds since the

unit was last operated or if the ignition switch is

set to ACC or ON while the unit is turned off. To

cancel the demo mode, you need to display the

initial settings. Select DEMO (demo display set-

ting) and turn off the demo display. For details,

refer to Initial settings on page 9.

In case of trouble

Should this unit fail to operate properly, please

contact your dealer or nearest authorized

PIONEER Service Station.

Before you start

2

Section

Before you start

En

01

Head unit

DEH-3400UB

b c dea87

12 3 4 5 6

9

Part Part

1 h (eject) 8

(back/display)

2

(list) 9 c/d

3

MULTI-CONTROL

(M.C.)

a

BAND/

(iPod

control)

4 SRC/OFF b 1 to 6

5 Disc loading slot c PTY

6 USB port d

AUX input jack

(3.5 mm stereo

jack)

7

(color) e Detach button

DEH-2400UB

b c dea87

12 3 4 5 6

9

Part Part

1 h (eject) 8

(back/display)

2

(list) 9 c/d

Part Part

3

MULTI-CONTROL

(M.C.)

a

BAND/

(iPod

control)

4 SRC/OFF b 1 to 6

5 Disc loading slot c PTY

6 USB port d

AUX input jack

(3.5 mm stereo

jack)

7

e Detach button

CAUTION

! Use an optional Pioneer USB cable (CD-

U50E) to connect the USB audio player/USB

memory as any device connected directly to

the unit will protrude out from the unit and

may be dangerous.

! Do not use unauthorized products.

Display indication

1

87 93 5

2 4 6

Indicator State

1

Main dis-

play sec-

tion

! Tuner: band and frequency

! RDS: program service

name, PTY information and

other literal information

! Built-in CD, USB storage

device and iPod: elapsed

playback time and text in-

formation

2

(list)

The list function is being oper-

ated.

3 LOC Local seek tuning is on.

4

(TA) TA function is on.

5

(TP) A TP station is tuned in.

6

(re-

peat)

Track or folder repeat is on.

7

(ran-

dom/shuf-

fle)

Random play is on.

The iPod source is selected

and the shuffle or shuffle all

function is on.

8

(sound re-

triever)

The sound retriever function is

on.

9

(iPod

control)

This unit’s iPod function is op-

erated from your iPod.

Set up menu

When you turn the ignition switch to ON after in-

stallation, set up menu appears on the display.

You can set up the menu options below.

1 After installation of this unit, turn the

ignition switch to ON.

SET UP appears.

2 Turn M.C. to switch to YES. Press M.C. to

select.

# If you do not operate for 30 seconds, the set up

menu will not be displayed.

# If you prefer not to set up at this time, turn M.C.

to switch to NO. Press to select.

If you select NO, you cannot set up in the set up

menu.

3 Perform the following procedures to set

the menu.

To proceed to the next menu option, you need to

confirm your selection.

CLOCK SET (setting the clock)

1 Turn M.C. to adjust hour.

2 Press M.C. to select minute.

3 Turn M.C. to adjust minute.

4 Press M.C. to confirm the selection.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek

tuning is 50 kHz. When AF or TA is on, the tuning

step automatically changes to 100 kHz. It may be

preferable to set the tuning step to 50 kHz when

AF is on.

! The tuning step remains at 50 kHz during man-

ual tuning.

1 Turn M.C. to select the FM tuning step.

50 (50 kHz)—100 (100 kHz)

2 Press M.C. to confirm the selection.

DEMO (demo display setting)

1 Turn M.C. to set the demo display to on or off.

2 Press M.C. to confirm the selection.

English

Operating this unit

3

Section

Operating this unit

En

02

TITLE (multi-language)

This unit can display the text information of a com-

pressed audio file even if they are embedded in a

Western European or Russian language.

! If the embedded language and the selected

language setting are not the same, text infor-

mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Turn M.C. to select the desired setting.

EUR (European)—RUS (Russian)

2 Press M.C. to confirm the selection.

QUIT appears.

4 To finish your settings, turn M.C. to select

YES. Press to select.

# If you prefer to change your setting again, turn

M.C. to switch to NO. Press to select.

Notes

! You can set up the menu options in the initial

settings. For details about the settings, refer

to Initial settings on page 9.

! You can cancel set up menu by pressing

SRC/OFF.

Basic operations

Important

! Handle gently when removing or attaching

the front panel.

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight

and high temperatures.

! To avoid damaging the device or vehicle inte-

rior, remove any cables and devices attached

to the front panel before detaching it.

Removing the front panel to protect your unit from

theft

1 Press the detach button to release the front

panel.

2 Push the front panel upward (M) and then pull

it toward (N) you.

3 Always keep the detached front panel in a pro-

tection device such as a protection case.

Re-attaching the front panel

1 Slide the front panel to the left.

Make sure to insert the tabs on the left side of

the head unit into the slots on the front panel.

2 Press the right side of the front panel until it is

firmly seated.

If you cannot attach the front panel to the

head unit successfully, make sure that you are

placing the front panel onto the head unit cor-

rectly. Forcing the front panel into place may

result in damage to the front panel or head

unit.

Turning the unit on

1 Press SRC/OFF to turn the unit on.

Turning the unit off

1 Press and hold SRC/OFF until the unit turns

off.

Selecting a source

1 Press SRC/OFF to cycle between:

TUNER (tuner)—CD (built-in CD player)—USB

(USB)/iPod (iPod)—AUX (AUX)

Adjusting the volume

1 Turn M.C. to adjust the volume.

CAUTION

For safety reasons, park your vehicle when re-

moving the front panel.

Note

When this unit’s blue/white lead is connected to

the vehicle’s auto-antenna relay control termi-

nal, the vehicle’s antenna extends when this

unit’s source is turned on. To retract the anten-

na, turn the source off.

Menu operations identical

for set up menu/function

settings/audio adjustments/

initial settings/lists

Returning to the previous display

Returning to the previous list (the folder one level

higher)

1 Press

.

Returning to the ordinary display

Canceling the initial setting menu/set up menu

1 Press BAND/

.

Returning to the ordinary display from the list

1 Press BAND/

.

Tuner

Basic operations

Selecting a band

1 Press BAND/

until the desired band (F1, F2,

F3 for FM or MW/LW) is displayed.

Recalling preset stations

1 Press c or d.

! If MAN (manual tuning) is selected in SEEK,

you cannot recall preset stations. You need to

select PCH (preset channel) in SEEK. For de-

tails about the settings, refer to SEEK (left/right

key setting) on page 6.

Manual tuning (step by step)

1 Press c or d.

! If PCH (preset channel) is selected in SEEK,

you cannot tune up or down manually. You

need to select MAN (manual tuning) in SEEK.

For details about the settings, refer to SEEK

(left/right key setting) on page 6.

Seeking

1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing

c or d.

While pressing and holding c or d, you can

skip stations. Seek tuning starts as soon as

you release c or d.

Note

This unit’s AF (alternative frequencies search)

function can be turned on and off. AF should be

off for normal tuning operation (refer to AF (al-

ternative frequencies search) on the next page).

Operating this unit

4

Section

Operating this unit

En

02

Storing and recalling stations

for each band

Using preset tuning buttons

1 When you find a station that you want

to store in memory, press one of the preset

tuning buttons (1 to 6) and hold until the

preset number stops flashing.

2 Press one of the preset tuning buttons (1

to 6) to select the desired station.

Switching the RDS display

% Press .

Program ser vice name—PTY information—En-

tertainment—Frequency

# PTY information and the frequency appear on the

display for eight seconds.

# Depending on the band, text information can be

changed.

Using PTY functions

You can tune in to a station using PTY (program

type) information.

Searching for an RDS station by PTY information

You can search for general types of broadcasting

programs, such as those listed in the following

section. Refer to this page.

1 Press PTY.

2 Turn M.C. to select a program type.

NEWS/INFO—POPULAR—CLASSICS—

OTHERS

3 Press M.C. to begin the search.

The unit searches for a station broadcasting

that type of program. When a station is found,

its program service name is displayed.

PTY (program type ID code) information is

listed in the following section. Refer to this

page.

! To cancel the search, press M.C. again.

! The program of some stations may differ

from that indicated by the transmitted PTY.

! If no station is broadcasting the type of

program you searched for, NOT FOUND is

displayed for about two seconds and then

the tuner returns to the original station.

PTY list

NEWS/INFO

NEWS (News), AFFAIRS (Current affairs), INFO

(Information), SPORT (Sports), WEATHER (Weath-

er), FINANCE (Finance)

POPULAR

POP MUS (Popular music), ROCK MUS (Rock

music), EASY MUS (Easy listening), OTH MUS

(Other music), JAZZ (Jazz), COUNTRY (Country

music), NAT MUS (National music), OLDIES

(Oldies music), FOLK MUS (Folk music)

CLASSICS

L. CLASS (Light classical), CLASSIC (Classical)

OTHERS

EDUCATE (Education), DRAMA (Drama), CUL-

TURE (Culture), SCIENCE (Science), VARIED (Var-

ied), CHILDREN (Children’s), SOCIAL (Social

affairs), RELIGION (Religion), PHONE IN (Phone

in), TOURING (Travel), LEISURE (Leisure), DOCU-

MENT (Documentaries)

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following proce-

dures to set the function.

# If MW/LW band is selected, only BSM, LOCAL

and SEEK are available.

BSM (best stations memory)

BSM (best stations memory) automatically stores

the six strongest stations in the order of their sig-

nal strength.

1 Press M.C. to turn BSM on.

To cancel, press M.C. again.

REGION (regional)

When AF is used, the regional function limits the

selection of stations to those broadcasting region-

al programs.

1 Press M.C. to turn the regional function on or

off.

LOCAL (local seek tuning)

Local seek tuning lets you tune in to only those

radio stations with sufficiently strong signals for

good reception.

1 Press M.C. to select the desired setting.

FM: OFF—LV1—LV2—LV3—LV4

MW/LW: OFF—LV1 —LV2

The highest level setting allows reception of

only the strongest stations, while lower levels

allow the reception of weaker stations.

PTY SEARCH (program type selection)

You can tune in to a station using PTY (program

type) information.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the desired setting.

NEWS/INFO—POPULAR—CLASSICS—

OTHERS

3 Press M.C. to begin the search.

The unit searches for a station broadcasting

that type of program. When a station is found,

its program service name is displayed.

For PTY (program type ID code) information,

refer to this page.

The program of some stations may differ from

that indicated by the transmitted PTY.

If no station is broadcasting the type of pro-

gram you searched for, NOT FOUND is dis-

played for about two seconds and then the

tuner returns to the original station.

TA (traffic announcement standby)

1 Press M.C. to turn traffic announcement

standby on or off.

AF (alternative frequencies search)

1 Press M.C. to turn AF on or off.

NEWS (news program interruption)

1 Press M.C. to turn the NEWS function on or

off.

English

Operating this unit

5

Section

Operating this unit

En

02

SEEK (left/right key setting)

You can assign a function to the left and right keys

of the unit.

Select MAN (manual tuning) to tune up or down

manually or select PCH (preset channel) to switch

between preset channels.

1 Press M.C. to select MAN or PCH.

CD/CD-R/CD-RW and USB

storage devices

Basic operations

Playing a CD/CD-R/CD-RW

1 Insert the disc into the disc loading slot with

the label side up.

Ejecting a CD/CD-R/CD-RW

1 Press h.

Playing songs on a USB storage device

1 Open the USB port cover.

2 Plug in the USB storage device using a USB

cable.

A song will be played automatically.

Stopping playback of files on a USB storage de-

vice

1 You may disconnect the USB storage device at

any time.

The unit stops playback.

Selecting a folder

1 Press 1/

or 2/ .

Selecting a track

1 Press c or d.

Fast forwarding or reversing

1 Press and hold c or d.

! When playing compressed audio, there is no

sound during fast forward or reverse.

Returning to root folder

1 Press and hold BAND/

.

Switching between compressed audio and CD-DA

1 Press BAND/

.

Switching between playback memory devices

You can switch between playback memory devices

on USB storage devices with more than one Mass

Storage Device-compatible memory device.

1 Press BAND/

.

! You can switch between up to 32 different

memory devices.

Note

Disconnect USB storage devices from the unit

when not in use.

Displaying text information

Selecting the desired text information

1 Press

.

! Depending on the version of iTunes used to

write MP3 files to a disc or media file types, in-

compatible text stored within an audio file may

be displayed incorrectly.

! Text information items that can be changed

depend on the media.

Selecting and playing files/

tracks from the name list

1 Press to switch to the file/track name

list mode.

2 Use M.C. to select the desired file name

(or folder name).

Changing the file or folder name

1 Turn M.C.

Playing

1 When a file or track is selected, press M.C.

Viewing a list of the files (or folders) in the se-

lected folder

1 When a folder is selected, press M.C.

Playing a song in the selected folder

1 When a folder is selected, press and hold M.C.

Advanced operations using

special buttons

Selecting a repeat play range

1 Press 6/

to cycle between the following:

CD/CD-R/CD-RW

! ALL – Repeat all tracks

! ONE – Repeat the current track

! FLD – Repeat the current folder

USB audio player/USB memory

! ALL – Repeat all files

! ONE – Repeat the current file

! FLD – Repeat the current folder

Playing tracks in random order

1 Press 5/

to turn random play on or off.

Tracks in a selected repeat range are played in

random order.

! To change songs during random play, press d

to switch to the next track. Pressing c restarts

playback of the current track from the begin-

ning of the song.

Pausing playback

1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich

sound (sound retriever)

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off)

1 is effective for low compression rates, and 2

is effective for high compression rates.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following proce-

dures to set the function.

REPEAT (repeat play)

1 Press M.C. to select a repeat play range.

For details, refer to Selecting a repeat play range

on this page.

RANDOM (random play)

1 Press M.C. to turn random play on or off.

PAUSE (pause)

1 Press M.C. to pause or resume.

S.RTRV (sound retriever)

Automatically enhances compressed audio and

restores rich sound.

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on this page.

iPod

Basic operations

Playing songs on an iPod

1 Open the USB port cover.

2 Connect an iPod to the USB cable using an

iPod Dock Connector.

A song will be played automatically.

Selecting a song (chapter)

1 Press c or d.

Operating this unit

6

Section

Operating this unit

En

02

Selecting an album

1 Press 1/

or 2/ .

! The album may not be selected correctly if the

iPod has more than one album with the same

title on it. Select the album you want to listen

to using list search. For details, refer to Brows-

ing for a song on this page.

Fast forwarding or reversing

1 Press and hold c or d.

Notes

! The iPod cannot be turned on or off when the

control mode is set to CTRL AUDIO.

! Disconnect headphones from the iPod be-

fore connecting it to this unit.

! The iPod will turn off about two minutes after

the ignition switch is set to OFF.

Displaying text information

Selecting the desired text information

1 Press

.

Browsing for a song

1 Press to switch to the top menu of list

search.

2 Use M.C. to select a category/song.

Changing the name of the song or category

1 Turn M.C.

Playlists—artists—albums—songs—podcasts

—genres—composers—audiobooks

Playing

1 When a song is selected, press M.C.

Viewing a list of songs in the selected category

1 When a category is selected, press M.C.

Playing a song in the selected category

1 When a category is selected, press and hold

M.C.

Searching the list by alphabet

1 When a list for the selected category is dis-

played, press

to switch to alphabet search

mode.

! You also can switch to alphabet search

mode by turning M.C. twice.

2 Turn M.C. to select a letter.

3 Press M.C. to display the alphabetical list.

! To cancel searching, press

.

Notes

! You can play playlists created with the PC ap-

plication (MusicSphere). The application will

be available on our website.

! Playlists that you created with the PC appli-

cation (MusicSphere) are displayed in abbre-

viated form.

Advanced operations using

special buttons

Selecting a repeat play range

1 Press 6/

to cycle between the following:

! OFF – Repeat off

! ONE – Repeat the current song

! ALL – Repeat all songs in the selected list

! You cannot select OFF when CTRL AUDIO is

selected. Refer to Operating this unit’siPod

function from your iPod on this page.

Playing all songs in random order (shuffle all)

1 Press 5/

to turn shuffle all on.

! When the control mode is set to CTRL iPod/

CTRL APP, shuffle play is on.

Pausing playback

1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich

sound (sound retriever)

1 Press 3/S.Rtrv to cycle between:

1—2—OFF (off)

1 is effective for low compression rates, and 2

is effective for high compression rates.

Playing songs related to the

currently playing song

You can play songs from the following lists.

• Album list of the currently playing artist

• Song list of the currently playing album

• Album list of the currently playing genre

1 Press and hold M.C. to switch to link play

mode.

2 Turn M.C. to change the mode; press to

select.

! ARTIST – Plays an album of the artist cur-

rently being played.

! ALBUM – Plays a song from the album cur-

rently being played.

! GENRE – Plays an album from the genre cur-

rently being played.

The selected song/album will be played after the

currently playing song.

Notes

! The selected song/album may be canceled if

you operate functions other than link search

(e.g. fast forward and reverse).

! Depending on the song selected to play, the

end of the currently playing song and the be-

ginning of the selected song/album may be

cut off.

Operating this unit’s iPod

function from your iPod

You can listen to the sound from your iPod appli-

cations using your car’s speakers, when

CTRL APP is selected.

! This function is not compatible with iPod

nano 1st generation.

APP Mode is compatible with the following iPod

models.

! iPhone 4 (software version 4.1 or later)

! iPhone 3GS (soft ware version 3.0 or later)

! iPhone 3G (software version 3.0 or later)

! iPhone (software version 3.0 or later)

! iPod touch 4th generation (software version

4.1 or later)

! iPod touch 3rd generation (software version

3.0 or later)

! iPod touch 2nd generation (software version

3.0 or later)

! iPod touch 1st generation (software version

3.0 or later)

% Press BAND/

to switch the control

mode.

! CTRL iPod – This unit’s iPod function can be

operated from the connected iPod.

! CTRL APP – Play back the sound from your

iPod applications.

! CTRL AUDIO – This unit’s iPod function can

be operated from this unit.

Notes

! Switching the control mode to CTRL iPod/

CTRL APP pauses song playback. Operate

the iPod to resume playback.

! The following functions are still accessible

from the unit even if the control mode is set

to CTRL iPod/CTRL APP.

— Pausing

— Fast forward/reverse

— Song up/down

! When the control mode is set to CTRL iPod,

operations are limited as follows:

English

Operating this unit

7

Section

Operating this unit

En

02

— The function settings are not available.

— The browse function cannot be operated from

this unit.

Function settings

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select FUNCTION.

3 Turn M.C. to select the function.

After selecting, perform the following proce-

dures to set the function.

! When the control mode is set to CTRL iPod/

CTRL APP, only PAUSE or S.RTRV is avail-

able.

REPEAT (repeat play)

1 Press M.C. to select a repeat play range.

For details, refer to Selecting a repeat play range

on the previous page.

SHUFFLE (shuffle)

1 Press M.C. to select your favorite setting.

! SNG – Play back songs in the selected list

in random order.

! ALB – Play back songs from a randomly se-

lected album in order.

! OFF – Cancel random play.

SHUFFLE ALL (shuffle all)

1 Press M.C. to turn shuffle all on.

To turn off, set SHUFFLE in the FUNCTION

menu to off.

LINK PLAY (link play)

1 Press M.C. to display the setting mode.

2 Turn M.C. to change the mode; press to select.

For details about the settings, refer to Playing

songs related to the currently playing song on

the previous page.

PAUSE (pause)

1 Press M.C. to pause or resume.

AUDIO BOOK (audiobook speed)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select your favorite setting.

! FASTER – Playback at a speed faster than

normal

! NORMAL – Playback at normal speed

! SLOWER – Playback at a speed slower

than normal

3 Press M.C. to confirm the selection.

S.RTRV (sound retriever)

Automatically enhances compressed audio and

restores rich sound.

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on the previous page.

Audio adjustments

1 Press M.C. to display the main menu.

2 Turn M.C. to change the menu option

and press to select AUDIO.

3 Turn M.C. to select the audio function.

After selecting, perform the following proce-

dures to set the audio function.

FAD/BAL (fader/balance adjustment)

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between fader (front/rear)

and balance (left/right).

3 Turn M.C. to adjust speaker balance.

! When the rear output and RCA output setting

are SW, you cannot adjust front/rear speaker

balance. Refer to REAR-SP (rear output setting)

on the next page. Refer to PREOUT (preout set-

ting) on the next page.

PRESET EQ (equalizer recall)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the equalizer.

DYNAMIC—VOCAL—NATURAL—CUSTOM

—FLAT—POWERFUL

3 Press M.C. to confirm the selection.

! You can also switch the equalizer by pressing

repeatedly (DEH-2400UB).

TONE CTRL (equalizer adjustment)

! Adjusted equalizer curve settings are stored in

CUSTOM.

1 Press M.C. to display the setting mode.

2 Press M.C. to select BASS (bass)/MID (mid)/

TREBLE (treble).

3 Turn M.C. to adjust the level.

Adjustment range: +6 to –6

LOUD (loudness)

Loudness compensates for deficiencies in the low-

frequency and high-frequency ranges at low vol-

ume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW(low)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output

which can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)—

OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

! This function is not available for DEH-2400UB.

! When you select OFF in SUB.W, you cannot se-

lect this function. For details, refer to SUB.W

(subwoofer on/off setting) on this page.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the cut-off fre-

quency and output level of the subwoofer.

Cut-off frequency (Cut-off frequency display

flashes.)—Output level (Output level display

flashes.)

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ

Output level: –24 to +6

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the

volume level of each source to prevent radical

changes in volume when switching between sour-

ces.

! Settings are based on the FM volume level,

which remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Operating this unit

8

Section

Operating this unit

En

02

Initial settings

Important

PW SAVE (power saving) is cancelled if the ve-

hicle battery is disconnected and will need to be

turned back on once the battery is reconnected.

When PW SAVE (power saving) is off, depend-

ing on connection methods, the unit may con-

tinue to draw power from the battery if your

vehicle’s ignition doesn’t have an ACC (acces-

sory) position.

1 Press and hold SRC/OFF until the unit

turns off.

2 Press SRC/OFF and hold until function

name appears in the display.

3 Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock

display you wish to set.

Hour—Minute

3 Turn M.C. to adjust the clock.

CLOCK (clock display)

You can turn the clock display on or off.

The clock display disappears temporarily when

you perform other operations, but the clock dis-

play appears again after 25 seconds.

1 Press M.C. to turn the clock display on or off.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek

tuning is 50 kHz. When AF or TA is on, the tuning

step automatically changes to 100 kHz. It may be

preferable to set the tuning step to 50 kHz when

AF is on.

! The tuning step remains at 50 kHz during man-

ual tuning.

1 Press M.C. to select the FM tuning step.

50 (50 kHz)—100 (100 kHz)

AUTO-PI (auto PI seek)

The unit can automatically search for a different

station with the same programming, even during

preset recall.

1 Press M.C. to turn Auto PI seek on or off.

AUX (auxiliary input)

Activate this setting when using an auxiliary de-

vice connected to this unit.

1 Press M.C. to turn AUX on or off.

USB PNP (plug and play)

This setting allows you to switch your source to

USB/iPod automatically.

1 Press M.C. to turn the plug and play function

on or off.

ON – When a USB storage device/iPod is con-

nected, depending on the type of device, the

source is automatically switched to USB/iPod

when you turn on the engine. If you disconnect

your USB storage device/iPod, this unit’s

source is turned off.

OFF – When a USB storage device/iPod is con-

nected, the source is not switched to USB/

iPod automatically. Please change the source

to USB/iPod manually.

REAR-SP (rear output setting)

The rear speaker leads output can be used for full-

range speaker or subwoofer connection.

If you switch to SW, you can connect a rear speak-

er lead directly to a subwoofer without using an

auxiliary amp.

Initially, REAR-SP is set for rear full-range speaker

connection (FUL).

1 Press M.C. to select the desired setting.

FUL—SW

! Even if you change this setting, there will

be no output if you select OFF in SUB.W

(Refer to SUB.W (subwoofer on/off setting)

on the previous page).

! If you change this setting, subwoofer out-

put in the audio menu will return to the fac-

tory settings.

PREOUT (preout setting)

The RCA outputs can be used for rear speaker or

subwoofer connection.

If you switch to SW, you can connect a rear speak-

er lead directly to a subwoofer without using an

auxiliary amp.

Initially, PREOUT is set for rear full-range speaker

connection (SW).

1 Press M.C. to select the desired setting.

SW—REA

! Even if you change this setting, there will

be no output if you select OFF in SUB.W

(Refer to SUB.W (subwoofer on/off setting)

on the previous page).

! If you change this setting, subwoofer out-

put in the audio menu will return to the fac-

tory settings.

DEMO (demo display setting)

1 Press M.C. to turn the demo display on or off.

! If PW SAVE is on, DEMO cannot be selected.

SCROLL (scroll mode setting)

When ever scroll is set to ON, recorded text infor-

mation scrolls continuously in the display. Set to

OFF if you prefer the information to scroll just

once.

1 Press M.C. to turn the ever scroll on or off.

TITLE (multi-language)

This unit can display the text information of a com-

pressed audio file even if they are embedded in a

Western European or Russian language.

! If the embedded language and the selected

language setting are not the same, text infor-

mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Press M.C. to select the desired setting.

EUR (European)—RUS (Russian)

PW SAVE (power saving)

Switching this function on enables you to reduce

the consumption of battery power.

! Turning on the source is the only operation al-

lowed when this function is on.

1 Press M.C. to turn the power save on or off.

Selecting the illumination color

Only for DEH-3400UB

This unit is equipped with multiple-color illumi-

nation. You can select desired colors for the keys

and display of this unit. You also can customize

the colors you want to use.

Selecting the key color from the

illumination color list

Only for DEH-3400UB

You can select desired colors for the keys of this

unit.

1 Press

.

English

Operating this unit

9

Section

Operating this unit

En

02

2 Turn M.C. to display KEY COLOR and

press to select.

3 Turn M.C. to select the illumination color.

You can select one option from the following list.

! 30 preset colors (WHITE to ROSE)

! SCAN (cycle through all colors)

! 3 sets of colors (WARM, AMBIENT, CALM)

! CUSTOM (customized illumination color)

4 Press M.C. to confirm the selection.

Notes

! When SCAN is selected, the system auto-

matically cycles through the 30 preset colors.

! When WARM is selected, the system auto-

matically cycles through the warm colors.

! When AMBIENT is selected, the system au-

tomatically cycles through the ambient col-

ors.

! When CALM is selected, the system auto-

matically cycles through the calm colors.

! When CUSTOM is selected, the customized

color saved is selected.

! To cancel selecting the illumination color,

press

.

Selecting the display color from

the illumination color list

Only for DEH-3400UB

You can select the desired colors for the display

of this unit.

1 Press

.

2 Turn M.C. to display DISP COLOR and

press to select.

3 Turn M.C. to select the illumination color.

You can select one option from the following list.

! 30 preset colors (WHITE to ROSE)

! SCAN (cycle through all colors)

! 3 sets of colors (WARM, AMBIENT, CALM)

! CUSTOM (customized illumination color)

4 Press M.C. to confirm the selection.

Note

For details about colors on the list, refer to Se-

lecting the key color from the illumination color

list on the previous page.

Selecting key and display color

from the illumination color list

Only for DEH-3400UB

You can select the desired colors for the keys

and display of this unit.

1 Press

.

2 Turn M.C. to display BOTH COLOR and

press to select.

3 Turn M.C. to select the illumination color.

You can select one option from the following list.

! 30 preset colors (WHITE to ROSE)

! SCAN (cycle through all colors)

4 Press M.C. to confirm the selection.

Notes

! You cannot select 3 sets of preset colors and

CUSTOM in this function.

! Once you select a color in this function, col-

ors on the keys and display of this unit auto-

matically switch to the color you selected.

! For details about colors on the list, refer to

Selecting the key color from the illumination

color list on the previous page.

Customizing the illumination color

Only for DEH-3400UB

1 Press

.

2 Turn M.C. to display KEY COLOR or

DISP COLOR. Press to select.

3 Press M.C. and hold until the customizing

illumination color setting appears in the dis-

play.

4 Press M.C. to select the primary color.

R (red)—G (green)—B (blue)

5 Turn M.C. to adjust the brightness level.

Adjustment range: 0 to 60

# You cannot select a level below 10 for all three of

R (red), G (green), and B (blue) at the same time.

# You can also perform the same operation on

other colors.

Notes

! You cannot create a custom illumination

color when SCAN or a set of colors (WARM,

AMBIENT,orCALM) is selected.

! You can create custom illumination colors

for both KEY COLOR and DISP COLOR.

Switching the dimmer setting

You can adjust the brightness of illumination.

% Press and hold

.

Using an AUX source

1 Insert the stereo mini plug into the AUX

input jack.

2 Press SRC/OFF to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-

ting is turned on. For more details, refer to AUX

(auxiliary input) on the previous page.

Sound muting

Sound is muted automatically when:

! A call is made or received using a cell phone

connected to this unit.

! Voice guidance is output from a connected

Pioneer navigation unit.

The sound is turned off, MUTE is displayed and

no audio adjustments, except volume control,

are possible. Operation returns to normal when

the phone connection or the voice guidance is

ended.

Operating this unit

10

Section

Operating this unit

En

02

Connections

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

O

N

S

T

A

R

T

O

F

ACC position No ACC position

! Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle’s auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

! The black cable is ground. Ground cables for

this unit and other equipment (especially,

high-current products such as power amps)

must be wired separately. If they are not, an

accidental detachment may result in a fire or

malfunction.

This unit

1

3 45

2

1 Power cord input

2 Rear output or subwoofer output

3 Antenna input

4 Fuse (10 A)

5 Wired remote input

Hard-wired remote control adaptor can be

connected (sold separately).

Power cord

1

3

2

4

5

6

b

8

9

7

a

e

d

c

1 To power cord input

2 Depending on the kind of vehicle, the func-

tion of 3 and 5 may be different. In this

case, be sure to connect 4 to 5 and 6 to

3.

3 Yellow

Back-up (or accessory)

4 Yellow

Connect to the constant 12 V supply termi-

nal.

5 Red

Accessory (or back-up)

6 Red

Connect to terminal controlled by ignition

switch (12 V DC).

7 Connect leads of the same color to each

other.

8 Black (chassis ground)

9 Blue/white

The pin position of the ISO connector will dif-

fer depending on the type of vehicle. Connect

9 and b when Pin 5 is an antenna control

type. In another type of vehicle, never con-

nect 9 and b.

a Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

b Blue/white

Connect to auto-antenna relay control termi-

nal (max. 300 mA 12 V DC).

c Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

d Speaker leads

White: Front left +

White/black: Front left *

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Green/black: Rear left * or subwoofer *

Violet: Rear right + or subwoofer +

Violet/black: Rear right * or subwoofer *

e ISO connector

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to con-

nect to both connectors.

Notes

! Change the initial setting of this unit. Refer

to REAR-SP (rear output setting) on page 9.

Refer to PREOUT (preout setting) on page 9.

The subwoofer output of this unit is monau-

ral.

! When using a subwoofer of 70 W (2 Ω), be

sure to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and green/

black leads.

English

Installation

11

Section

Installation

En

03

Power amp (sold separately)

Perform these connections when using the op-

tional amplifier.









1

3

2

4

55

1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately)

3 Connect with RCA cables (sold separately)

4 To Rear output or subwoofer output

5 Rear speaker or subwoofer

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the

vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Use commercially available parts when instal-

ling.

DIN Front-mount

1 Insert the mounting sleeve into the dash-

board.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

1

2

1 Dashboard

2 Mounting sleeve

3 Install the unit as illustrated.

1

2

3

4

5

1 Nut

2 Firewall or metal support

3 Metal strap

4 Screw

5 Screw (M4 × 8)

# Make sure that the unit is installed securely in

place. An unstable installation may cause skipping

or other malfunctions.

DIN Rear-mount

1 Determine the appropriate position

where the holes on the bracket and the side

of the unit match.

2 Tighten two screws on each side.

1

2

3

1 Tapping screw (5 mm × 8 mm)

2 Mounting bracket

3 Dashboard or console

Removing the unit

1 Remove the trim ring.

1 Trim ring

2 Notched tab

! Releasing the front panel allows easier ac-

cess to the trim ring.

! When reattaching the trim ring, point the

side with the notched tab down.

2 Insert the supplied extraction keys into

both sides of the unit until they click into

place.

3 Pull the unit out of the dashboard.

Removing and re-attaching the front

panel

You can remove the front panel to protect your

unit from theft.

Press the detach button and push the front

panel upward and pull it toward you.

For details, refer to Removing the front panel to

protect your unit from theft and Re-attaching the

front panel on page 4.

Installation

12

Section

Installation

En

03

Troubleshooting

Symptom Cause Action

The display il-

lumination

turns on and

off at random.

Demo mode is

on.

Turn off the demo

display setting.

The display

automatically

returns to the

ordinary dis-

play.

You did not per-

form any opera-

tion within

about 30 sec-

onds.

Perform operation

again.

The repeat

play range

changes un-

expectedly.

Depending on

the repeat play

range, the se-

lected range

may change

when another

folder or track is

being selected

or during fast

forwarding/re-

versing.

Select the repeat

play range again.

A subfolder is

not played

back.

Subfolders can-

not be played

when FLD (fold-

er repeat) is se-

lected.

Select another re-

peat play range.

NO XXXX ap-

pears when a

display is

changed (NO

TITLE, for ex-

ample).

There is no em-

bedded text in-

formation.

Switch the display

or play another

track/file.

Symptom Cause Action

The unit is

malfunction-

ing.

There is inter-

ference.

You are using a

device, such as

a cellular

phone, that

transmits elec-

tric waves near

the unit.

Move electrical

devices that may

be causing the in-

terference away

from the unit.

Error messages

When you contact your dealer or your nearest

Pioneer Service Center, be sure to note the error

message.

Built-in CD Player

Message Cause Action

ERROR-07,

11, 12, 17, 30

The disc is dirty. Clean the disc.

The disc is

scratched.

Replace the disc.

ERROR-07,

10, 11, 12,

15, 17, 30,

A0

There is an elec-

trical or me-

chanical error.

Turn the ignition

switch OFF and

back ON, or

switch to a differ-

ent source, then

back to the CD

player.

ERROR-15 The inserted

disc is blank.

Replace the disc.

ERROR-23 Unsupported

CD format.

Replace the disc.

FRMT READ Sometimes

there is a delay

between the

start of playback

and when you

start to hear any

sound.

Wait until the

message disap-

pears and you

hear sound.

Message Cause Action

NO AUDIO The inserted

disc does not

contain any

playable files.

Replace the disc.

SKIPPED The inserted

disc contains

DRM protected

files.

Replace the disc.

PROTECT All the files on

the inserted

disc are em-

bedded with

DRM.

Replace the disc.

USB storage device/iPod

Message Cause Action

NO DEVICE When plug and

play is off, no

USB storage de-

vice or iPod is

connected.

! Turn the plug

and play on.

! Connect a com-

patible USB stor-

age device/iPod.

FRMT READ Sometimes

there is a delay

between the

start of playback

and when you

start to hear any

sound.

Wait until the

message disap-

pears and you

hear sound.

NO AUDIO There are no

songs.

Transfer the audio

files to the USB

storage device

and connect.

The connected

USB storage de-

vice has secur-

ity enabled.

Follow the USB

storage device in-

structions to dis-

able the security.

Message Cause Action

SKIPPED The connected

USB storage de-

vice contains

files embedded

with Windows

Mediaä DRM 9/

10.

Play an audio file

not embedded

with Windows

Media DRM 9/10.

PROTECT All the files in

the USB storage

device are em-

bedded with

Windows Media

DRM 9/10.

Transfer audio

files not em-

bedded with

Windows Media

DRM 9/10 to the

USB storage de-

vice and connect.

N/A USB The USB device

connected to is

not supported

by this unit.

! Connect a USB

Mass Storage

Class compliant

device.

! Disconnect

your device and

replace it with a

compatible USB

storage device.

English

Additional information

13

Appendix

Additional information

En

Message Cause Action

CHECK USB The USB con-

nector or USB

cable has short-

circuited.

Check that the

USB connector or

USB cable is not

caught in some-

thing or dam-

aged.

The connected

USB storage de-

vice consumes

more than

500 mA (maxi-

mum allowable

current).

Disconnect the

USB storage de-

vice and do not

use it. Turn the

ignition switch to

OFF, then to ACC

or ON and then

connect only

compliant USB

storage devices.

The iPod oper-

ates correctly

but does not

charge.

Make sure the

connection cable

for the iPod has

not shorted out

(e.g., not caught

in metal objects).

After checking,

turn the ignition

switch OFF and

back ON, or dis-

connect the iPod

and reconnect.

Message Cause Action

ERROR-19 Communication

failed.

Perform one of

the following op-

erations.

–Turn the ignition

switch OFF and

back ON.

–Disconnect the

USB storage de-

vice.

–Change to a dif-

ferent source.

Then, return to

the USB source.

iPod failure. Disconnect the

cable from the

iPod. Once the

iPod’s main

menu is dis-

played, reconnect

the iPod and reset

it.

ERROR-23 USB storage de-

vice was not for-

matted with

FAT12, FAT16 or

FAT32.

USB storage de-

vice should be for-

matted with

FAT12, FAT16 or

FAT32.

ERROR-16 The iPod firm-

ware version is

old.

Update the iPod

version.

iPod failure. Disconnect the

cable from the

iPod. Once the

iPod’s main

menu is dis-

played, reconnect

the iPod and reset

it.

STOP There are no

songs in the

current list.

Select a list that

contains songs.

Message Cause Action

NOT FOUND No related

songs.

Transfer songs to

the iPod.

Handling guidelines

Discs and player

Use only discs that feature either of the following

two logos.

Use 12-cm discs. Do not use 8-cm discs or an

adapter for 8-cm discs.

Use only conventional, fully circular discs. Do not

use shaped discs.

Do not insert anything other than a CD into the

CD loading slot.

Do not use cracked, chipped, warped, or other-

wise damaged discs as they may damage the play-

er.

Unfinalized CD-R/RW discs cannot be played

back.

Do not touch the recorded surface of the discs.

Store discs in their cases when not in use.

Do not attach labels, write on or apply chemicals

to the surface of the discs.

To clean a CD, wipe the disc with a soft cloth out-

ward from the center.

Condensation may temporarily impair the player’s

performance. Let it rest for about one hour to ad-

just to a warmer temperature. Also, wipe any

damp discs off with a soft cloth.

Playback of discs may not be possible because of

disc characteristics, disc format, recorded applica-

tion, playback environment, storage conditions,

and so on.

Road shocks may interrupt disc playback.

When using discs that can be printed on label sur-

faces, check the instructions and the warnings of

the discs. Depending on the discs, inserting and

ejecting may not be possible. Using such discs

may result in damage to this equipment.

Do not attach commercially available labels or

other materials to the discs.

! The discs may warp making the disc unplay-

able.

! The labels may come off during playback and

prevent ejection of the discs, which may result

in damage to the equipment.

USB storage device

Connections via USB hub are not supported.

Do not connect anything other than a USB stor-

age device.

Additional information

14

Appendix

Additional information

En

Firmly secure the USB storage device when driv-

ing. Do not let the USB storage device fall onto the

floor, where it may become jammed under the

brake or accelerator pedal.

Depending on the USB storage device, the follow-

ing problems may occur.

! Operations may vary.

! The storage device may not be recognized.

! Files may not be played back properly.

! The device may generate noise in the radio.

iPod

Do not leave the iPod in places with high tempera-

tures.

To ensure proper operation, connect the dock con-

nector cable from the iPod directly to this unit.

Firmly secure the iPod when driving. Do not let the

iPod fall onto the floor, where it may become

jammed under the brake or accelerator pedal.

About iPod settings

! When an iPod is connected, this unit changes

the EQ (equalizer) setting of the iPod to off in

order to optimize the acoustics. When you dis-

connect the iPod, the EQ returns to the original

setting.

! You cannot set Repeat to off on the iPod when

using this unit. Repeat is automatically

changed to All when the iPod is connected to

this unit.

Incompatible text saved on the iPod will not be dis-

played by the unit.

DualDiscs

DualDiscs are two-sided discs that have a record-

able CD for audio on one side and a recordable

DVD for video on the other.

Since the CD side of DualDiscs is not physically

compatible with the general CD standard, it may

not be possible to play the CD side with this unit.

Frequent loading and ejecting of a DualDisc may

result in scratches on the disc. Serious scratches

can lead to playback problems on this unit. In

some cases, a DualDisc may become stuck in the

disc loading slot and will not eject. To prevent this,

we recommend you refrain from using DualDisc

with this unit.

Please refer to the information from the disc man-

ufacturer for more detailed information about

DualDiscs.

Compressed audio

compatibility (disc, USB)

WMA

File extension: .wma

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to

384 kbps (VBR)

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Windows Media Audio Professional, Lossless,

Voice/DRM Stream/Stream with video: Not com-

patible

MP3

File extension: .mp3

Bit rate: 8 kbps to 320 kbps (CBR), VBR

Sampling frequency: 8 kHz to 48 kHz (32 kHz,

44.1 kHz, 48 kHz for emphasis)

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is given priority over Version

1.x.)

M3u playlist: Not compatible

MP3i (MP3 interactive), mp3 PRO: Not compatible

WAV

File extension: .wav

Quantization bits: 8 and 16 (LPCM), 4 (MS

ADPCM)

Sampling frequency: 16 kHz to 48 kHz (LPCM),

22.05 kHz and 44.1 kHz (MS ADPCM)

Supplemental information

Only the first 32 characters can be displayed as a

file name (including the file extension) or a folder

name.

Russian text to be displayed on this unit should be

encoded in one of the following character sets:

! Unicode (UTF-8, UTF-16)

! A character set other than Unicode that is

used in a Windows environment and is set to

Russian in the multi-language setting

This unit may not operate correctly depending on

the application used to encode WMA files.

There may be a slight delay at the start of playback

of audio files embedded with image data or audio

files stored on a USB storage device that has nu-

merous folder hierarchies.

Disc

Playable folder hierarchy: up to eight tiers (A prac-

tical hierarchy is less than two tiers).

Playable folders: up to 99

Playable files: up to 999

File system: ISO 9660 Level 1 and 2, Romeo, Joliet

Multi-session playback: Compatible

Packet write data transfer: Not compatible

Regardless of the length of blank sections be-

tween the songs from the original recording, com-

pressed audio discs play with a short pause

between songs.

USB storage device

Playable folder hierarchy: up to eight tiers (A prac-

tical hierarchy is less than two tiers).

Playable folders: up to 500

Playable files: up to 15 000

Playback of copyright-protected files: Not compati-

ble

Partitioned USB storage device: Only the first par-

tition can be played.

There may be a slight delay when starting play-

back of audio files on a USB storage device with

numerous folder hierarchies.

CAUTION

! Pioneer cannot guarantee compatibility with

all USB mass storage devices and assumes

no responsibility for any loss of data on

media players, smart phones, or other devi-

ces while using this product.

! Do not leave discs or a USB storage device

in any place that is subject to high tempera-

tures.

English

Additional information

15

Appendix

Additional information

En

iPod compatibility

This unit supports only the following iPod models.

Supported iPod software versions are shown

below. Older versions may not be supported.

Made for

! iPhone 4 (software version 4.1)

! iPhone 3GS (software version 3.0.1)

! iPhone 3G (software version 2.0)

! iPhone (software version 1.1.1)

! iPod nano 6th generation (software version

1.0)

! iPod nano 5th generation (software version

1.0.1)

! iPod nano 4th generation (software version

1.0)

! iPod nano 3rd generation (software version

1.0)

! iPod nano 2nd generation (software version

1.1.2)

! iPod nano 1st generation (software version

1.2.0)

! iPod touch 4th generation (software version

4.1)

! iPod touch 3rd generation (software version

3.1.1)

! iPod touch 2nd generation (software version

2.1.1)

! iPod touch 1st generation (software version

1.1)

! iPod classic 160GB (software version 2.0.2)

! iPod classic 120GB (software version 2.0)

! iPod classic (software version 1.0)

Depending on the generation or version of the

iPod, some functions may not be available.

Operations may vary depending on the software

version of iPod.

When using an iPod, an iPod Dock Connector to

USB Cable is required.

A Pioneer CD-IU51 interface cable is also avail-

able. For details, consult your dealer.

About the file/format compatibility, refer to the

iPod manuals.

Audiobook, Podcast: Compatible

CAUTION

Pioneer accepts no responsibility for data lost

on the iPod, even if that data is lost while this

unit is used.

Sequence of audio files

The user cannot assign folder numbers and

specify playback sequences with this unit.

Example of a hierarchy













Level 1 Level 2 Level 3 Level 4

01

02

03

04

05

: Folder

: Compressed

audio file

01 to 05: Folder

number

1 to 6: Playback

sequence

Disc

Folder selection sequence or other operation

may differ depending on the encoding or writing

software.

USB storage device

Playback sequence is the same as recorded se-

quence in the USB storage device.

To specify the playback sequence, the following

method is recommended.

1 Create a file name that includes numbers

that specify the playback sequence (e.g.,

001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder.

3 Save the folder containing files on the USB

storage device.

However, depending on the system environment,

you may not be able to specify the playback se-

quence.

For USB portable audio players, the sequence is

different and depends on the player.

Russian character chart

D: C D: C D: C D: C D: C

: А : Б : В : Г : Д

: Е, Ё : Ж : З : И, Й : К

: Л : М : Н : О : П

: Р : С : Т : У : Ф

: Х : Ц : Ч

: Ш,

Щ

: Ъ

: Ы : Ь : Э : Ю : Я

D: Display C: Character

Copyright and trademark

iTunes

Apple and iTunes are trademarks of Apple Inc.,

registered in the U.S. and other countries.

MP3

Supply of this product only conveys a license for

private, non-commercial use and does not con-

vey a license nor imply any right to use this prod-

uct in any commercial (i.e. revenue-generating)

real time broadcasting (terrestrial, satellite,

cable and/or any other media), broadcasting/

streaming via internet, intranets and/or other

networks or in other electronic content distribu-

tion systems, such as pay-audio or audio-on-de-

mand applications. An independent license for

such use is required. For details, please visit

http://www.mp3licensing.com.

WMA

Windows Media is either a registered trademark

or trademark of Microsoft Corporation in the

United States and/or other countries.

This product includes technology owned by

Microsoft Corporation and cannot be used or

distributed without a license from Microsoft

Licensing, Inc.

iPod & iPhone

iPhone, iPod, iPod classic, iPod nano, and iPod

touch are trademarks of Apple Inc., registered in

the U.S. and other countries.

“Made for iPod” and “Made for iPhone” mean

that an electronic accessory has been designed

to connect specifically to iPod or iPhone, respec-

tively, and has been certified by the developer to

meet Apple performance standards. Apple is

not responsible for the operation of this device

or its compliance with safety and regulator y

standards. Please note that the use of this ac-

cessory with iPod or iPhone may affect wireless

performance.

Additional information

16

Appendix

Additional information

En

Specifications

General

Power so urce ................... 14.4 V DC (10.8 V to 15.1 V al-

lowable)

Grounding system ............ Negative type

Maximum current consumption

................................... 10.0 A

Dimensions (W × H × D):

DIN

Chassis .............. 178mm × 50mm ×

165 mm

Nose .................. 188 mm × 58mm ×

16 mm

D

Chassis .............. 178mm × 50mm ×

165 mm

Nose .................. 170 mm × 46mm ×

16 mm

Weight ............................. 1.1 kg

Audio

Maximum power output ... 50 W × 4

70 W × 1/2 W (for subwoofer)

Continuous power output

................................... 22W × 4 (50 Hz to 15000Hz,

5 % THD, 4 W load, both chan-

nels driven)

Load impedance .............. 4W (4 W to 8 W allowable)

Preout maximum output level

................................... 2.0V

Tone controls:

Bass

Frequency .......... 100Hz

Gain .................. ±12dB

Mid

Frequency .......... 1 kHz

Gain .................. ±12dB

Treble

Frequency .......... 10kHz

Gain .................. ±12dB

Subwoofer (mono):

Frequency ................. 50Hz/63 Hz/80 Hz/100 Hz/

125 Hz

Slope ........................ –18 dB/oct

Gain ......................... +6dB to –24 dB

Phase ....................... Normal/Reverse

CD player

System ............................ Compact disc audio system

Usable discs .................... Compact disc

Signal-to-noise ratio ......... 94dB (1kHz) (IEC-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch

audio)

(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

USB

USB standard specification

................................... USB 2.0 full speed

Maximum current supply

................................... 500mA

USB Class ....................... MSC (Mass Storage Class)

File system ....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2ch

audio)

(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

FM tuner

Frequency range .............. 87.5 MHz to 108.0 MHz

Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N:

30 dB)

Signal-to-noise ratio ......... 72dB (IEC-A network)

MW tuner

Frequency range .............. 531 kHz to 1 602kHz

Usable sensitivity ............. 25µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62dB (IEC-A network)

LW tuner

Frequency range .............. 153 kHz to 281 kHz

Usable sensitivity ............. 28 µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62dB (IEC-A network)

Note

Specifications and the design are subject to

modifications without notice.

English

Additional information

17

Appendix

En

Nous vous remercions d’avoir acheté cet ap-

pareil PIONEER

Pour garantir une utilisation correcte, lisez bien

ce mode d’emploi avant d’utiliser cet appareil. Il

est particulièrement important que vous lisiez et

respectiez les indications ATTENTION et PRÉ-

CAUTION de ce mode d’emploi. Conservez-le

dans un endroit sûr et facilement accessible pour

toute consultation ultérieure.

Si vous souhaitez vous débarrasser de cet ap-

pareil, ne le mettez pas à la poubelle avec vos

ordures ménagères. Il existe un système de

collecte séparé pour les appareils électroni-

ques usagés, qui doivent être récupérés, trai-

tés et recyclés conformément à la législation.

Dans les états membres de l’UE, en Suisse et en

Norvège, les foyers domestiques peuvent rap-

porter leurs produits électroniques usagés gra-

tuitement à des points de collecte spécifiés ou à

un revendeur (sous réserve d’achat d’un produit

similaire).

Dans les pays qui ne sont pas mentionnés ci-

dessus, veuillez contacter les autorités locales

pour vous informer de la méthode correcte de

mise au rebut.

En agissant ainsi vous assurerez que le produit

que vous mettez au rebut est soumis au proces-

sus de traitement, de récupération et de recy-

clage nécessaire et éviterez ainsi les effets

négatifs potentiels sur l’environnement et la

santé publique.

Quelques mots sur cet appareil

Les fréquences du syntoniseur de cet appareil

sont attribuées pour une utilisation en Europe

de l’Ouest, Asie, Moyen Orient, Afrique et Océ-

anie. Son utilisation dans d’autres régions peut

se traduire par une réception de mauvaise qua-

lité. La fonction RDS (radio data system) n’est

opérationnelle que dans les régions où des si-

gnaux RDS sont diffusés pour les stations FM.

PRÉCAUTION

Ce produit est classifié comme produit laser

de classe 1 selon la norme IEC 60825-1:2007

“Sécurité des appareils à laser” et contient un

module laser de classe 1M. Pour assurer une

sécurité permanente, n’enlevez aucun couver-

cle et n’essayez pas d’accéder à l’intérieur du

produit. Faites effectuer l’entretien par du per-

sonnel qualifié.

APPAREIL À LASER DE CLASSE 1

ATTENTION—ÉMISSIONS DE RADIATIONS LASER

INVISIBLES DE CLASSE 1M SI OUVERT. NE PAS OBSERVER

DIRECTEMENT AVEC DES INSTRUMENTS OPTIQUES.

PRÉCAUTION

! Ne laissez pas cet appareil entrer en contact

avec des liquides. Cela pourrait provoquer

une électrocution. Tout contact avec des li-

quides pourrait aussi provoquer des domma-

ges, de la fumée et une surchauffe de

l’appareil.

! Le Pioneer CarStereo-Pass est utilisable seu-

lement en Allemagne.

! Maintenez le niveau d’écoute à une valeur

telle que vous puissiez entendre les sons pro-

venant de l’extérieur.

! Évitez tout contact avec l’humidité.

! Si la batterie est débranchée ou déchargée,

le contenu de la mémoire sera effacé.

Remarque

Les opérations de réglage des fonctions sont va-

lidées même si le menu est annulé avant la

confirmation des opérations.

Quelques mots sur ce mode

d’emploi

! Dans les instructions suivantes, les mémoi-

res USB et les lecteurs audio USB sont col-

lectivement appelés “périphériques de

stockage USB”.

! Dans ce manuel, iPod et iPhone sont dési-

gnés par le terme “iPod”.

Mode de démonstration

Important

! La non-connexion du fil rouge (ACC) de cet

appareil à une borne couplée avec les opéra-

tions de mise en/hors service du contact d’al-

lumage peut conduire au déchargement de

la batterie.

! Rappelez-vous que si la démonstration des

fonctions continue à fonctionner quand le

moteur est coupé, cela peut décharger la

batterie.

La démonstration démarre automatiquement si

vous n’utilisez pas cet appareil dans les 30 se-

condes environ depuis la dernière opération ou

si le contact est réglé sur ACC ou ON alors que

l’appareil est hors service. Pour annuler le mode

de démonstration, vous devez afficher les régla-

ges initiaux. Sélectionnez DEMO (réglage de l’af-

fichage de démonstration) et désactivez

l’affichage de démonstration. Pour les détails,

reportez-vous à la page 26, Réglages initiaux.

En cas d’anomalie

En cas d’anomalie, veuillez contacter votre re-

vendeur ou le centre d’entretien agréé par

PIONEER le plus proche.

Avant de commencer

18

Section

Avant de commencer

Fr

01

Appareil central

DEH-3400UB

b c dea87

12 3 4 5 6

9

Partie Partie

1 h (éjection) 8

(retour/affi-

chage)

2

(liste) 9 c/d

3

MULTI-CONTROL

(M.C.)

a

BAND/

(contrôle de

l’iPod)

4 SRC/OFF b 1 à 6

5

Fente de charge-

ment des disques

c PTY

6 Port USB d

Jack d’entrée

AUX (jack stéréo

3,5 mm)

7

(couleur) e

Touche de retrait

de la face avant

DEH-2400UB

b c dea87

12 3 4 5 6

9

Partie Partie

1 h (éjection) 8

(retour/affi-

chage)

2

(liste) 9 c/d

3

MULTI-CONTROL

(M.C.)

a

BAND/

(contrôle de

l’iPod)

4 SRC/OFF b 1 à 6

5

Fente de charge-

ment des disques

c PTY

6 Port USB d

Jack d’entrée

AUX (jack stéréo

3,5 mm)

7

e

Touche de retrait

de la face avant

PRÉCAUTION

! Utilisez un câble USB Pioneer optionnel (CD-

U50E) pour connecter le lecteur audio USB/

la mémoire USB, étant donné que n’importe

quel périphérique relié directement à l’appa-

reil dépassera de l’appareil et peut s’avérer

dangereux.

! N’utilisez pas de produits non autorisés.

Indications affichées

1

87 93 5

2 4 6

Indica-

teur

État

1

Section

d’afficha-

ge princi-

pal

! Syntoniseur : gamme et fré-

quence

! RDS : nom du ser vice de

programme, informations

PTY et autres informations

textuelles

! Lecteur de CD intégré, péri-

phérique de stockage USB

et iPod: temps de lecture

écoulé et informations tex-

tuelles

2

(liste) La fonction liste est utilisée.

3 LOC

L’accord automatique sur une

station locale est en service.

4

(TA) La fonction TA est en service.

5

(TP)

L’appareil est accordé sur une

station TP.

6

(répéti-

tion de la

lecture)

La fonction de répétition d’une

plage ou d’un dossier est acti-

vée.

7

(lec-

ture aléa-

toire)

La lecture aléatoire est activée.

La source iPod est sélection-

née et la fonction de lecture

aléatoire ou lecture aléatoire

de toutes les plages est acti-

vée.

8

(sound re-

triever)

La fonction Sound Retriever est

activée.

9

(contrôle

de l’iPod)

La fonction iPod de cet appa-

reil est utilisée à partir de votre

iPod.

Menu de configuration

Lorsque vous mettez le contact d’allumage sur

ON après l’installation, le menu de configura-

tion s’affiche sur l’écran.

Vous pouvez configurer les options de menu ci-

dessous.

1 Après avoir installé l’appareil, mettez le

contact d’allumage sur ON.

SET UP s’affiche.

2 Tournez M.C. pour passer à YES. Appuyez

sur M.C. pour sélectionner.

# Si vous n’effectuez aucune opération dans les

30 secondes environ, le menu de configuration ne

s’affichera pas.

# Si vous préférez ne pas effectuer la configuration

pour l’instant, tournez M.C. pour passer à NO. Ap-

puyez pour sélectionner.

Si vous sélectionnez NO, vous ne pouvez pas effec-

tuer de réglage dans le menu de configuration.

3 Effectuez les procédures suivantes pour

configurer le menu.

Pour passer à la prochaine option de menu,

vous devez confirmer votre sélection.

CLOCK SET (réglage de l’horloge)

1 Tournez M.C. pour régler l’heure.

2 Appuyez sur M.C. pour sélectionner les minu-

tes.

3 Tournez M.C. pour régler les minutes.

4 Appuyez sur M.C. pour confirmer la sélection.

FM STEP (incrément d’accord FM)

Français

Utilisation de l’appareil

19

Section

Utilisation de l’appareil

Fr

02

Normalement, l’incrément d’accord FM employé

par l’accord automatique est 50 kHz. Quand la

fonction AF ou TA est en service, l’incrément d’ac-

cord passe automatiquement à 100 kHz. Il peut

être préférable de régler l’incrément d’accord à

50 kHz quand la fonction AF est en service.

! Pendant l’accord manuel, l’incrément d’ac-

cord est maintenu à 50 kHz.

1 Tournez M.C. pour choisir l’incrément d’accord

FM.

50 (50 kHz)—100 (100 kHz)

2 Appuyez sur M.C. pour confirmer la sélection.

DEMO (réglage de l’affichage de démonstration)

1 Appuyez sur M.C. pour activer ou désactiver

l’affichage de démonstration.

2 Appuyez sur M.C. pour confirmer la sélection.

TITLE (multilingue)

Cet appareil peut afficher les informations textuel-

les d’un fichier audio compressé même si elles

sont incorporées dans une langue d’Europe de

l’Ouest ou russe.

! Si la langue incorporée et la langue sélection-

née sont différentes, les informations textuel-

les peuvent ne pas s’afficher correctement.

! Certains caractères peuvent ne pas s’afficher

correctement.

1 Tournez M.C. pour choisir le réglage désiré.

EUR (Langue européenne)—RUS (Russe)

2 Appuyez sur M.C. pour confirmer la sélection.

QUIT s’affiche.

4 Pour terminer la configuration, tournez

M.C. pour sélectionner YES. Appuyez pour

sélectionner.

# Si vous souhaitez modifier à nouveau vos régla-

ges, tournez M.C. pour passer à NO. Appuyez pour

sélectionner.

Remarques

! Vous pouvez configurer les options de menu

dans les réglages initiaux. Pour des détails

sur les réglages, reportez-vous à la page 26,

Réglages initiaux .

! Vous pouvez annuler le menu de configura-

tion en appuyant sur SRC/OFF.

Opérations de base

Important

! Lorsque vous enlevez ou remontez la face

avant, manipulez-la doucement.

! Évitez de heurter la face avant.

! Conservez la face avant à l’abri des tempéra-

tures élevées et de la lumière directe du so-

leil.

! Pour éviter d’endommager le périphérique

ou l’intérieur du véhicule, retirez tous les câ-

bles et périphériques connectés à la face

avant, avant d’enlever cette dernière.

Retrait de la face avant pour protéger l’appareil

contre le vol

1 Appuyez sur la touche de retrait pour libérer la

face avant.

2 Poussez la face avant vers le haut (M), puis

tirez-la vers vous (N).

3 Conservez toujours la face avant dans un boî-

tier de protection lorsqu’elle est détachée.

Remontage de la face avant

1 Faites glisser la face avant vers la gauche.

Assurez-vous d’insérer les encoches sur le

côté gauche de l’appareil central dans les fen-

tes du panneau de commande.

2 Appuyez sur le côté droit de la face avant jus-

qu’àcequ’elle soit bien en place.

Si vous ne pouvez pas monter la face avant

sur l’appareil central, vérifiez que la face avant

est correctement placée sur l’appareil central.

Forcer la face avant en position risque de l’en-

dommager ou d’endommager l’appareil cen-

tral.

Mise en service de l’appareil

1 Appuyez sur SRC/OFF pour mettre en service

l’appareil.

Mise hors service de l’appareil

1 Maintenez la pression sur SRC/OFF jusqu’àce

que l’appareil soit mis hors tension.

Choix d’une source

1 Appuyez sur SRC/OFF pour parcourir les op-

tions disponibles :

TUNER (syntoniseur)—CD (lecteur de CD inté-

gré)—USB (USB)/iPod (iPod)—AUX (AUX)

Réglage du volume

1 Tournez M.C. pour régler le volume.

PRÉCAUTION

Pour des raisons de sécurité, garez votre véhi-

cule pour retirer la face avant.

Remarque

Si le fil bleu/blanc de l’appareil est relié à la

prise de commande du relais de l’antenne moto-

risée du véhicule, celle-ci se déploie lorsque la

source est mise en service. Pour rétracter l’an-

tenne, mettez la source hors service.

Opérations communes des

menus pour le(s) menu de

configuration/réglages des

fonctions/réglages audio/

réglages initiaux/listes

Retour à l’affichage précédent

Retour à la liste précédente (le dossier de niveau

immédiatement supérieur)

1 Appuyez sur

.

Retour à l’affichage ordinaire

Annulation du menu des réglages initiaux/menu

de configuration

1 Appuyez sur BAND/

.

Retour à l’affichage ordinaire à partir de la liste

1 Appuyez sur BAND/

.

Utilisation de l’appareil

20

Section

Utilisation de l’appareil

Fr

02

La page charge ...

Pioneer DEH-3400UB Manuel utilisateur

Pioneer DEH-3400UB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents