Whirlpool WTW7500GC0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WTW7500GC0

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

W11037201A

W11037202A - SP

If you have any problems or questions, visit us at www.whirlpool.com

Pour tout problème ou toute question, consulter www.whirlpool.ca

Use & Care Guide

Guide d’utilisation et d’entretien

Top-Loading High Efﬁciency Low-Water Washer

Laveuse haute efﬁcacité à faible consommation

d’eau avec chargement par le dessus

Para obtener acceso

al Manual de uso y

cuidado en español, o para

obtener información adicional

acerca de su producto, visite:

www.whirlpool.com.

Designed to use only HE High Efﬁciency

detergents.

Conçue pour l’utilisation d’un détergent haute

efﬁcacité seulement.

Table of Contents

WASHER SAFETY ............................................................2

WHAT’S NEW UNDER THE LID? ....................................4

CONTROL PANEL AND FEATURES ...............................5

Dispensers and faucet ....................................................... 6

CYCLE GUIDE ..................................................................7

USING YOUR WASHER ...................................................8

WASHER MAINTENANCE ..................................................13

TROUBLESHOOTING ..........................................................15

WARRANTY............................................................................20

ASSISTANCE OR SERVICE .............................. Back Cover

Table des matières

SÉCURITÉ DE LA LAVEUSE .........................................21

QUOI DE NEUF SOUS LE COUVERCLE? ...................22

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES .............................................23

Distributeurs et robinet ....................................................25

GUIDE DES PROGRAMMES .........................................26

UTILISATION DE LA LAVEUSE .....................................28

ENTRETIEN DE LA LAVEUSE ............................................ 34

DÉPANNAGE ..........................................................................36

GARANTIE ..............................................................................44

ASSISTANCE OU SERVICE ................. Couverture arrière

Washer Safety

What’s New Under the Lid?

Choosing the Right Detergent

Use only High Efﬁciency detergents. The package will

be marked “HE” or “High Efﬁciency.” Low-water washing

creates excessive sudsing with a non-HE detergent. Using

non-HE detergent will likely result in longer cycle times and

reduced rinsing performance. It may also result in component

malfunction and, over time, buildup of mold or mildew. HE

detergents should be low-sudsing and quick-dispersing to

produce the right amount of suds for the best performance.

They should hold soil in suspension so it is not redeposited

onto clean clothes. Not all detergents labeled as High Efﬁciency

are identical in formulation and their ability to reduce suds.

For example, natural, organic, or homemade HE detergents

may generate a high level of suds. If you use one of these

and see an “F0E2” error code appear in the display, consider

using a different HE detergent. Always follow the detergent

manufacturer’s instructions to determine the amount of

detergent to use. Do not go over the Max line on the dispenser.

See “Using Laundry Product Dispensers” for more information.

Normal Sounds You Can Expect

At different stages of the wash cycle, you may hear sounds

and noises that are different from those of your previous washer.

For example, you may hear a clicking and hum at the beginning

of the cycle as the lid lock goes through a self-test. There will

be different kinds of humming and whirring sounds as the

washplate moves the load and as the basket is slowing down to

stop. And sometimes, you may hear nothing at all as the washer

determines the correct water level for your load or allows time

for clothes to soak.

Use only High Efﬁciency (HE) detergent.

Improved Cleaning

Low-water cleaning means concentrated cleaning. Rather

than diluting detergent as done in an agitator-style washer,

this washer delivers the detergent directly to the soils. This low

water wash also allows the clothing to move in a more effective

way to remove soils.

Automatic Load Size Sensing

Once you start the cycle, the lid will lock and the washer will

begin the sensing process to determine the correct water level

for the load.

Initially the basket will start to spin prior to adding water; this is

part of the sensing process and is normal. This low-water wash

method uses less water and energy compared to a traditional

agitator-style washer.

For best performance, it is recommended to load items in loose

heaps evenly around the washplate.

As the washer dampens and moves the load, the level

of the items will settle in the basket. This is normal and

does not indicate that more items should be added.

IMPORTANT: You will not see a washer basket full of water

as with your past agitator-style washer. It is normal for some

of the load to be above the water line.

Cleaning with Less Water

The most striking difference in your new washer is the low-water

washplate wash system. The washer automatically adjusts the

water level to the load size—no water level selector is needed.

Traditional agitator-style

washer

Low-water washer

Washplate

NOTE: The control panel features a sensitive surface that responds to a light touch of your ﬁnger. To ensure your selections are

registered, touch the control panel with your ﬁnger tip, not your ﬁngernail. When selecting a setting or option, simply touch its name

until the desired section is illuminated.

POWER BUTTON

Touch to turn the washer on. Touching once while the washer

is on will cancel the current cycle, touching twice will turn

the washer off.

WHAT TO WASH/HOW TO WASH

First select a cycle from “What to Wash” and then select

“How to Wash” to get the best combination cycle available

for the type of items you are going to wash. See “Cycle

Guide” for cycle details.

START/PAUSE BUTTON

Touch and hold the START/PAUSE button to begin

the selected cycle; touch again to pause a cycle.

LED TIME/STATUS DISPLAY

The Estimated Time Remaining display shows the time

required for the cycle to complete. Factors such as load

size and water pressure may affect the time shown in

the display. Tightly packed loads, unbalanced loads, or

excessive suds may cause the washer to adjust the cycle

time, as well.

If you have set a delay start to the cycle, the Estimated

Time Remaining display will show the delay time adjusted.

When the cycle is complete, the Done indicator will light

until the lid is opened.

ADD GARMENT

When Add Garment is lit, you may pause the washer,

open the lid, and add items. Touch and hold the

START/PAUSE button to start the washer again.

OPTIONS

You may add or remove options for each cycle. Not all

options can be used with all cycles, and some are preset

to work with certain cycles.

EXTRA RINSE

This option can be used to automatically add a second

rinse to most cycles.

DRAIN & SPIN

This option spins the load and drains any water in the tub.

The load is not rinsed.

RINSE & SPIN

Touch the DRAIN & SPIN button, then touch the EXTRA

RINSE button. This option combines a rinse and high spin

speed for loads requiring an additional rinse cycle

or to complete a load after power interruption.

Also use for loads that require rinsing only.

CLEAN WASHER

Use this every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water

level. Use with affresh

Washer Cleaner tablet or liquid

chlorine bleach to thoroughly clean the inside of your

washer. This cycle should not be interrupted. See

“Washer Care.”

IMPORTANT: Do not place garments or other items in

the washer during the Clean Washer cycle. Use this cycle

with an empty washer tub.

SIGNAL

Use this to turn the signal indicating the end of a wash

cycle to low, high, or off.

NOTE: You may also adjust the tones that sound when

a feature, setting, or option is touched. Touch and hold

SIGNAL for about 3 seconds to turn key activation

sounds to low, high, or off.

DELAY START

Touch DELAY START to delay the start of the wash cycle

up to 12 hours “12H.” Touch DELAY START until a “0H”

appears in the status display to turn off, or touch the

POWER button.

DEEP WATER

Use this option to add the maximum amount of water

to your wash cycle.

NOTE: Expect longer cycle times due to extended ﬁll

times when using the Deep Water option.

PRESOAK

Use this option to add an extra soak period to any cycle

to help loosen tough stains. The washer will ﬁll and pause

to soak, then begin the selected cycle.

CYCLE MODIFIERS

When you select a cycle, its default settings or the previous

cycle selection used will light up.

TEMPERATURE

Temperature Control senses and maintains uniform

water temperatures by regulating incoming hot and

cold water.

Control Panel and Features

5 6

Dispensers and faucet

High Efﬁciency “HE” detergent dispenser

Add liquid or powdered HE detergent product to this

dispenser for your main wash cycle. Remove tray if using

powder detergent.

IMPORTANT: Make sure tray is in drawer when using liquid

detergent and removed when using powder detergent.

Do not go over the Max line.

NOTE: Follow the manufacturer’s instructions to determine

the amount of detergent to use.

Liquid fabric softener dispenser

Pour measured liquid fabric softener into the liquid fabric

softener dispenser, if desired. It will dispense automatically

at the optimum time.

•

Use only liquid fabric softener in this dispenser.

Liquid chlorine bleach dispenser

This dispenser holds up to 3/4 cup (180 mL) liquid chlorine

bleach. The bleach will be automatically diluted and

dispensed at the optimum time during the wash cycle.

This dispenser cannot dilute powdered bleach.

NOTE: Fill dispenser with only liquid bleach.

Water faucet

The water faucet dispenses fresh water that can be used

for pretreating clothes, rinsing your detergent cup, or ﬁlling

your washer tub.

Faucet button

Press once to toggle on and press again to toggle off.

You do not need to hold the button.

NOTE: If accidentally left on for more than 10 minutes,

the faucet will automatically shut off.

Use only High Efﬁciency (HE) detergent.

Select a wash temperature based on the type of fabric

and soils being washed. For best results and following

the garment label instructions, use the warmest wash

water safe for your fabric.

• On some models and cycles, warm and hot water will

be cooler than what your previous washer provided.

• Even for cold wash settings, some warm water

may be added to the washer to maintain a minimum

temperature.

SOIL LEVEL

Soil Level (wash time) is preset for each wash cycle.

As you touch Soil Level, the cycle time (minutes) will

increase or decrease in the Estimated Time Remaining

display and a different wash time will appear.

Select the most suitable setting for your load. For heavily

soiled items, select Heavy Soil Level for more wash

time. For lightly soiled items, select Light Soil Level for

less wash time. Lighter soil level setting will help reduce

tangling and wrinkling.

SPIN SPEED

This washer automatically selects the spin speed

based on the cycle selected. The preset speeds can be

changed. Not all spin speeds are available with all cycles.

• Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load.

• Slower spin speeds mean less wrinkling, but will leave

your load more damp.

LID

The Lid Lock ( ) indicator lights up

when the lid is locked and cannot be

opened. If you need to open the lid,

touch and hold the START/PAUSE button.

The lid will unlock once the washer

movement has stopped. This may take

several minutes if the load was spinning at

high speed. Touch and hold the START/PAUSE

button again to restart the cycle.

Cycle Guide

How do you want to wash?

“How to Wash” Cycle Selection

Normal Quick Delicate

Heavy Duty

ColorLast

• Regular Wash • Saves Time • Gentle Cleaning

• Protects My

Fabrics

• Powerful Soil

Removal

• Gentle Cleaning

• Protects My Colors

What do you

want to wash?

“What to Wash”

Cycle Selection

Cottons/Linens

Colors

P A A A A

Bright Colors

R R R R P

Handwash Fabrics

R R P A R

Bras

R R P A R

Lingerie

R R P A R

Baby Clothes

R R R P R

Machine Wash Silks

R R P A R

Wool

R R

Dark Colors

Darks

P R A R R

Athletic/High Performance

Wear

R R A P A

T-Shirts

P R R R R

Sweatshirts

P R R R R

Jeans

P R R R R

Pajamas

P R R R R

Business Casual

R R

R P

Dress Shirts/Pants

R R R A P

No-Iron Fabrics

R R R R P

Dark Sheets

P R A R R

White Clothing

Whites

P R R R

White Shirts

P R R R

White T-Shirts

P R R R

Socks

R R

Undergarments

R R R P

Handkerchiefs

R R P R

Napkins

R R P R

White Sheets

P R A R

Tablecloths

P R R R

Towels

P R R R R

Terry Cloth

P R R R R

Hand Towels

P R R R R

Wash Cloths

P R R R R

Bath Towels

P R R R R

Blankets

Bedding/Bulky

P A R R R

Coats & Jackets

P A R R R

Comforters

P A R R R

Machine Wash Curtains

R R P A R

Machine Wash Slip Covers

P R R A R

Non-Rubber Lined Rugs

& Mats

P A R R R

Sleeping Bags

P A R A R

Your Whirlpool

washer has a unique user interface to help you select the best cycle you need for your load. The “What to Wash”

“How to Wash” layout guides you to the optimal cycle in two easy steps:

First determine what items are in the load that you are trying to wash. Use that to guide your “What to Wash” selection. Then determine

how you want the washer to wash them and select the appropriate “How to Wash” selection. See chart below for more details.

For best fabric care, choose the cycle

that best ﬁts the load being washed.

P – Preferred Cycle Selection

R – Recommended Alternate

A – Available but not optimal

Using Your Washer

Using Your Washer’s Faucet Before Washing

Rinsing Before Running

a Wash Cycle

• Press the faucet button once. You do not need to hold the

button.

• Turn off the faucet by pressing the button again.

• If accidentally left on, the faucet will automatically shut off.

• Water from the tub will automatically drain if the level

becomes too high. The water will also drain after 10 minutes

if the lid is left open.

1. Turn on faucet

IMPORTANT: Before rinsing, make sure to sort, prepare,

and load laundry as discussed in “Running a Wash Cycle.”

• If you choose to drain water in the tub: with the washer turned

on, select DRAIN & SPIN and touch and hold the START/

PAUSE button.

• Water in the tub will always be drained before you start

a wash cycle.

2. Drain water manually, if desired

• If you choose to rinse the laundry and then drain: with the

washer turned on, select RINSE & SPIN and touch and hold

the START/PAUSE button.

• Water in the tub will always be drained before you start

a wash cycle.

3. Rinse and drain water, if desired

Press faucet

button

Presoaking Without Running

a Wash Cycle

• Press the faucet button once. You do not need to hold

the button.

● TIP: You may want to add any detergent, color-safe bleach,

or oxi-type boosters while the faucet is running to mix it with

the water. (See Step 2 in the next column.)

• Turn off the faucet by pressing the button again.

● If accidentally left on, the faucet will automatically shut off.

● IMPORTANT: To stop the tub from draining automatically

in 10 minutes, you must close the lid. The water will remain

in the tub as long as the lid is closed and you take no action.

After 3 hours, the water will automatically be drained.

If you choose to drain water in the tub: with the washer

turned on, select DRAIN & SPIN and touch and hold the

START/PAUSE button.

NOTE: If you run a wash cycle, water in the tub will always be

drained before you start the cycle.

2. Drain water manually, if desired

If you choose to rinse the laundry: with the washer turned on,

select RINSE & SPIN and touch and hold the START/PAUSE

button. The washer will drain, spin, rinse the load, and spin

again.

NOTE: If you run a wash cycle, water in the tub will always be

drained before you start the cycle.

3. Rinse and drain water, if desired

• Empty pockets. Loose change, buttons, or any small

object can pass under the washplate and become

trapped, causing unexpected sounds.

• Sort items by recommended cycle, water temperature,

and colorfastness.

• Separate heavily soiled items from lightly soiled.

• Separate delicate items from sturdy fabrics.

• Do not dry items if stains remain after washing, as heat

can set stains into fabric.

• Treat stains promptly.

• Close zippers, fasten hooks, tie strings and sashes.

Remove non-washable trim and ornaments.

• Mend rips and tears to avoid further damage to items

during washing.

Helpful Tips:

• For best performance, use HE liquid detergent when

washing bulky items.

• When washing waterproof or water-resistant items,

load evenly.

• Use mesh bags to help avoid tangling when washing

delicate or small items.

• Turn knits inside out to avoid pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics

will pick up lint from towels, rugs, and chenille fabrics.

NOTE: Always read and follow fabric care labels instructions

to avoid damage to your items.

1. Sort and prepare your laundry

Running a Wash Cycle

Single-dose laundry packet, color-safe bleach, Oxi-type

boosters, or fabric softener crystals can be added to the

basket prior to adding laundry.

NOTE: Always follow manufacturer’s instructions.

2. Add laundry products

1. Turn on faucet

Press faucet

button

For best performance, load items

in loose heaps evenly around the

washplate. Try mixing different sized

items to reduce tangling.

IMPORTANT: Items need to move freely

for best cleaning and to reduce wrinkling and tangling.

3. Load laundry into washer

6. Add liquid fabric softener

Pour a measured amount of liquid fabric softener into tray;

always follow manufacturer’s directions for correct amount

of fabric softener based on your load size. Close dispenser

drawer. Fabric Softener is added during rinse.

IMPORTANT: Do not overﬁll or dilute. Overﬁlling the

dispenser will cause fabric softener to immediately dispense

into the washer.

If Extra Rinse option is selected, fabric softener will be

dispensed into the last rinse.

It is normal for a small amount of water to remain in the

dispenser at the end of a cycle.

Fabric softener tray

Liquid

Chlorine Bleach

5. Add liquid chlorine bleach

to dispenser

Do not overﬁll, dilute, or use more than 1 cup (236 mL).

Do not use color-safe bleach or Oxi products in the same

cycle with liquid chlorine bleach.

Add a measured amount of HE

detergent into detergent tray. This

tray holds 3 oz. (89 mL). If adding

powder HE detergent, remove the inside tray. Do not overﬁll

the tray; adding too much detergent may cause detergent to be

dispensed into the washer too early.

NOTE: Make sure the tray is in the drawer when using liquid

detergent and removed when using powder detergent. Do not go

over the Max line.

IMPORTANT: Use only High Efﬁciency detergents. The package

will be marked “HE” or “High Efﬁciency.” Low-water washing

creates excessive sudsing with a non-HE detergent. Using

non-HE detergent will likely result in longer cycle times and

reduced rinsing performance. It may also result in component

malfunction and, over time, buildup of mold or mildew. HE

detergents should be low-sudsing and quick-dispersing to

4. Add HE detergent

HE removable

detergent tray

NOTE: Do not add single-dose laundry packets, color-safe

bleach, Oxi-type boosters, or fabric softener crystals to

dispensers. They will not dispense correctly. Add to the

basket prior to adding laundry.

Using Laundry Product Dispensers

produce the right amount of suds for the best performance. They

should hold soil in suspension so it is not redeposited onto clean

clothes. Not all detergents labeled as High Efﬁciency are identical

in formulation and their ability to reduce suds. For example,

natural, organic, or homemade HE detergents may generate

a high level of suds. If you use one of these and see an “F0E2”

error code appear in the display, consider using a different

HE detergent. Always follow the detergent manufacturer’s

instructions to determine the amount of detergent to use.

Do not go over the Max line on the dispenser.

HELPFUL TIP: See “Washer Maintenance” for information

on recommended method of cleaning washer dispenser trays.

First touch a cycle from the “What to

Wash,” and then select the “How to Wash”

to get the best combination cycle available

for the type of items you are going to wash.

See “Cycle Guide” for cycle details. Not all

cycles are available on all models.

Estimated Time Remaining will light up with a cycle time.

You may notice time adjusting during the cycle. This is

normal.

If you do not want to begin a cycle immediately, you may

choose the Delay Start option.

To choose a delay time:

1. Touch the DELAY START button to select desired delay

time. Time will increase in hour increments up to 12 hours.

2. Touch and hold the START/PAUSE button to start delay

start time.

IMPORTANT: When delaying a cycle, use liquid HE

detergent only in the dispenser. Powdered detergents may

absorb moisture from a previous cycle and clump before

the wash cycle begins.

To cancel delay start:

1. Touch the POWER button to cancel Delay Start.

To pause delay start:

1. Touch the START/PAUSE button to pause delay start.

2. Touch and hold the START/PAUSE button again to start

the delay start time. If the delay start time is not started

after 10 minutes, the washer will power off.

8. Select type of load to wash

9. Select cycle modiﬁers

Once you select a cycle, the default modiﬁers or the previously

set modiﬁers for that cycle will be lit. Touch the cycle settings

buttons to change the Soil Level, Spin Speed, and Temperature,

if desired. Not all settings are available with all cycles.

NOTE: Always read and follow fabric care labels instructions

to avoid damage to your items.

7. Touch POWER button to turn

on washer

Make sure the dispenser drawer is closed completely, then

touch the POWER button to turn on the washer.

Temperature Suggested Fabrics

Hot

Some cold water is added

to save energy. This will be

cooler than your hot water

heater setting.

Whites and pastels

Durable items

Heavy soils

Warm

Some cold water will be

added, so this may be cooler

than what your previous

washer provided.

Bright colors

Moderate to light soils

Cool

Warm water is added to assist

in soil removal and to help

dissolve detergents.

Colors that bleed or fade

Light soils

Cold

Warm water may be added

to assist in soil removal and

to help dissolve detergents.

Dark colors that bleed or fade

Light soils

10. Select cycle options

Select any other cycle options you may wish to add, if not

previously set. Some cycles will automatically add certain

options such as Extra Rinse. These may be turned off if desired.

NOTE: Not all options are available with all cycles. Touch the

control panel to select any other options.

11. Touch and hold START/PAUSE

button to begin wash cycle

Touch and hold the START/PAUSE button to start the wash

cycle. When the cycle has ﬁnished, the end-of-cycle signal

will sound (if set). Promptly remove items when cycle is done

to avoid odor, reduce wrinkling, and reduce rusting of metal

hooks, zippers, and snaps.

Unlocking the lid to add items

If you need to open the lid to add one or two missed items:

Touch the START/PAUSE button to pause the washer;

the lid will unlock once the washer movement has stopped.

This may take several minutes if the load was spinning at

a high speed. Then close lid and touch and hold the START/

PAUSE button again to restart the cycle.

IMPORTANT: If the lid is left open for more than 10 minutes,

the water will pump out and the F8E6 error code will appear

on the display.

WASHER CARE (cont.)

2. Chlorine Bleach Procedure (Alternative):

a. Open the washer lid and remove any clothing

or items.

b. Add 1 cup (236 mL) of liquid chlorine bleach

to the bleach compartment.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

c. Close the washer lid.

d. Do not add any detergent or other chemical

to the washer when following this procedure.

e. Select the Clean Washer cycle.

f. Touch and hold the START/PAUSE button to begin

the cycle. The Clean Washer Cycle Operation is

described below.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, touch the POWER button. After

the Clean Washer cycle has stopped, run a

Rinse & Spin

cycle to rinse cleaner from washer.

Description of Clean Washer Cycle Operation:

1. This cycle will ﬁll to a water level higher than in normal

wash cycles to provide rinsing at a level above the water

line for normal wash cycle.

2. During this cycle, there will be some agitation and

spinning to increase the removal of soils.

After this cycle is complete, leave the lid open to allow

for better ventilation and drying of the washer interior.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe away any spills.

Use only mild soaps or cleaners when cleaning external

washer surfaces.

IMPORTANT: To avoid damaging the washer’s ﬁnish, do not

use abrasive products.

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of

replacement on the label with a permanent marker.

NOTE: This washer does not include inlet hoses.

See the Installation Instructions for more information.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer

Clean and Performing at Its Best

1. Always use High Efﬁciency (HE) detergents and follow

the HE detergent manufacturer’s instructions regarding

the amount of HE detergent to use. Never use more than

the recommended amount because that may increase the

rate at which detergent and soil residue accumulate inside

your washer, which may result in undesirable odor.

2. Use warm and hot wash water settings sometimes

(not exclusively cold water washes), because they do

a better job of controlling the rate at which soils and

detergent accumulate.

3. Always leave the washer lid open between uses

to help dry out the washer and prevent the buildup

of odor-causing residue.

Cleaning Your Top-Loading Washer

Read these instructions completely before beginning

the routine cleaning processes recommended below.

This Washer Maintenance Procedure should be performed,

at a minimum, once per month or every 30 wash cycles,

whichever occurs sooner, to control the rate at which soils

and detergent may otherwise accumulate in your washer.

Cleaning the Inside of the Washer

To keep your washer odor-free, follow the usage instructions

provided above, and use this recommended monthly

cleaning procedure:

Clean Washer Cycle

This washer has a special cycle that uses higher water

volumes in combination with affresh

Washer Cleaner

or liquid chlorine bleach to clean the inside of the washer.

Begin procedure

1. affresh

Washer Cleaner Cycle Procedure

(Recommended for Best Performance):

a. Open the washer lid and remove any clothing or items.

b. Place an affresh

Washer Cleaner tablet in the bottom

of the washer basket.

c. Do not place an affresh

Washer Cleaner tablet

in the detergent dispenser.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

e. Close the washer lid.

f. Select the Clean Washer cycle.

g. Touch and hold the START/PAUSE button to begin

the cycle. The Clean Washer Cycle Operation is

described in the next column.

NOTE: For best results, do not interrupt cycle. If cycle

must be interrupted, touch the POWER button. After the

Clean Washer cycle has stopped, run a

Rinse & Spin

cycle

to rinse cleaner from washer.

Washer Maintenance

Operate your washer only when you are home. If you are

moving or not using your washer for a period of time, follow

these steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer to avoid ﬂooding

due to water pressure surge.

NON-USE AND VACATION CARE

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in the basket

and run the washer on the Rinse & Spin cycle for about

30 seconds to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run washer through Bedding/Bulky and Heavy Duty

cycle to clean washer and remove antifreeze, if used.

Use only HE High Efﬁciency detergent. Use half the

manufacturer’s recommended amount for a medium-

size load.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain from drain system.

4. Unplug power cord.

5. Place inlet hoses inside washer basket.

6. Drape power cord and drain hose over the console

and secure with masking tape.

7. Place foam packing ring from original shipping materials

back inside washer. If you do not have packing ring,

place heavy blankets or towels into basket opening.

Close lid and place tape over lid and down front of

washer. Keep lid taped until washer is placed in

new location. Transport washer in the upright position.

CLEANING YOUR DISPENSER

IMPORTANT: Dispenser drawer and tray are not

dishwasher-safe.

You may ﬁnd laundry product residue leftover in your

dispenser drawer. To remove residue, follow this

recommended cleaning procedure:

1. Pull drawer out until you feel resistance.

2. Push one tab downward, then continue pulling out.

3. Wash in warm, soapy water, using a mild detergent.

4. Rinse with warm water.

5. Air dry or dry with a towel, then place back into slot.

Troubleshooting

If you experience Possible Causes Solution

Vibration or Off-Balance

Vibration, rocking, or

“walking”

Feet may not be in contact with the

ﬂoor and locked.

Front and rear feet must be in ﬁrm contact with ﬂoor, and washer

must be level to operate properly.

Washer may not be level. Check ﬂoor for ﬂexing or sagging. If ﬂooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See “Level the Washer” in the Installation Instructions.

Vibration during spinning

or washer stopped

Load could be unbalanced. Load items in loose heaps evenly around the washplate.

Adding wet items to washer or adding more water to basket

could unbalance washer.

Avoid washing single items. Balance a single item such as a

rug or jean jacket with a few extra items. If the dial is ﬂashing,

redistribute the load, close the lid, and touch and hold the

START/PAUSE button.

Use Bedding/Bulky and Heavy Duty cycle for oversized,

non-absorbent items such as comforters or poly-ﬁlled jackets.

Other items are not appropriate for Bedding/Bulky Heavy Duty

cycle. See “Cycle Guide.”

Item or load not suitable for selected cycle. See “Cycle Guide”

and “Using Your Washer.”

Noises – For normal operating sounds, go to www.whirlpool.com/product_help.

Clicking or metallic

noises

Objects may be caught in washer

drain system.

Empty pockets before washing. Loose items such as coins

could fall between basket and tub or may block pump. It may be

necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel basket.

Gurgling or humming Washer may be draining water. It is normal to hear the pump making a continuous humming

sound with periodic gurgling or surging as ﬁnal amounts of water

are removed during the spin/drain cycles.

Humming Load sensing may be occurring. You may hear the hum of the sensing spins after you have

started the washer. This is normal.

Whirring Basket may be slowing down. You may hear the whirring sound of the basket slowing down.

This is normal.

Water Leaks

Check the following for

proper installation:

Washer not level. Water may splash off basket if washer is not level.

Fill hoses not attached tightly. Tighten ﬁll-hose connection.

Fill hose washers Make sure all four ﬁll hose ﬂat washers are properly seated.

Drain hose connection Pull drain hose from washer cabinet and properly secure it to

drainpipe or laundry tub.

Do not place tape over drain opening.

Check household plumbing for leaks

or clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check all

household plumbing for leaks (laundry tubs, drain pipe, water

pipes, and faucets.)

Washer not loaded as

recommended.

An unbalanced load can cause basket to be out of alignment

and cause water to splash off tub. See “Using Your Washer”

for loading instructions.

Washer not performing as expected

Not enough water

in washer

Load not completely covered

in water.

This is normal operation for an HE low-water washer. The load

will not be completely underwater. The washer senses load

sizes and adds correct amount of water for optimal cleaning.

See “What’s New under the Lid.”

IMPORTANT: Do not add more water to washer. Adding water lifts

the items off the washplate, resulting in less effective cleaning.

Run clean washer cycle to optimize the water level and wash

performance.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

Washer won’t run or ﬁll;

washer stops working

(cont.)

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Normal washer operation. Lid must be closed for washer to run.

Washer will pause during certain phases of cycle. Do not

interrupt cycle.

Washer may be stopped to reduce suds.

Washer may be tightly packed. Remove several items, rearrange load evenly around the

washplate. Close lid, touch and hold the START/PAUSE button.

Add only one or two additional items after washer has started.

Do not add more water to the washer.

Not using HE detergent or using too

much HE detergent.

Only use HE detergent. Suds from regular detergents can slow

or stop the washer. Always measure detergent and following

detergent directions based on your load requirements.

To remove suds, cancel cycle. Select RINSE & SPIN. Select your cycle.

Touch and hold the START/PAUSE button. Do not add more detergent.

Washer not draining/

spinning; loads are

still wet

Small items may have been caught

in pump or between basket and tub,

which can slow draining.

Empty pockets and use garment bags for small items.

Using cycles with a lower spin speed. Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/speed spin

for your item.

Washer may be tightly packed or

unbalanced.

Tightly packed loads may not allow the washer to spin correctly,

leaving the load wetter than normal. Evenly arrange the wet load

for balanced spinning. Select RINSE & SPIN to remove excess

water. See “Using Your Washer” for loading recommendations.

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer won’t run or ﬁll;

washer stops working

Check for proper water supply.

Both hoses must be attached and have water ﬂowing to inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ﬂow.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer not draining/

spinning; loads are

still wet (cont.)

Load off balanced. See “Vibration or Off-Balance” in the “Troubleshooting” section

for more information.

Check plumbing for correct drain

hose installation. Drain hose

extends into standpipe farther

than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose

form and securely attach to drainpipe or tub. Do not tape

over drain opening. Lower drain hose if the end is higher than

96" (2.4 m) above the ﬂoor. Remove any clogs from drain hose.

Not using HE detergent or using too

much HE detergent.

Suds from regular detergent or using too much detergent can

slow or stop draining or spinning. Use only HE detergent. Always

measure and follow detergent directions for your load. To remove

extra suds, select RINSE & SPIN. Do not add detergent.

Incorrect or wrong wash

or rinse temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water ﬂowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy-saving controlled wash

temperatures.

ENERGY STAR

qualiﬁed washers use cooler wash and rinse

water temperatures than traditional top-loading washers.

This includes cooler hot and warm washes.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water ﬂowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on the washer may be clogged.

Remove any kinks in the inlet hose.

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can cause the washer to

operate incorrectly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow detergent directions based

on load size and soil level.

Washer may be tightly packed. The washer is less efﬁcient at rinsing when load is tightly

packed.

Load items in loose heaps evenly around the washplate.

Use cycle designed for the fabrics being washed.

Add only one or two additional items after the washer has

started.

Sand, pet hair, lint, etc.

on load after washing

Heavy sand, pet hair, lint, and

detergent or bleach residues may

require additional rinsing.

Add an Extra Rinse to the selected cycle.

Load is tangling Washer not loaded as recommended. Load items in loose heaps evenly around the washplate.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of items being washed.

Wash action and/or spin speed too

fast for load.

Select a cycle with a slower wash action and slower spin speed.

Note that items will be wetter than when using a higher speed spin.

Not cleaning or

removing stains

Wash load not completely

covered in water.

Washer senses load size and adds correct amount of water.

This is normal and necessary for clothes to move.

Added more water to washer. Do not add more water to washer. Adding water lifts the items

off the washplate, resulting in less effective cleaning.

Washer not loaded as recommended. Load items in loose heaps evenly around the washplate.

Add only one or two additional items after the washer has

started.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Not cleaning or

removing stains (cont.)

Not using HE detergent or using too

much HE detergent.

The suds from regular detergent can keep washer from

operating correctly.

Use only HE detergent. Be sure to measure correctly.

Always measure detergent and follow detergent directions based

on load size and soil level.

Not using correct cycle for

fabric type.

Use a higher soil level cycle option and warmer wash

temperature to improve cleaning.

If using Quick cycle, wash only a few items.

Use Whites/Normal cycle for tough cleaning.

See the “Cycle Guide” to match your load with the best cycle.

Not using dispensers. Use dispensers to avoid chlorine bleach and fabric softener

staining.

Load dispensers before starting a cycle.

Avoid overﬁlling.

Do not add products directly onto the load.

Not washing like colors together. Wash like colors together and remove promptly after the cycle

is complete to avoid dye transfer.

Odors Monthly maintenance not done as

recommended.

Run the Clean Washer cycle after every 30 washes. See “Washer

Care” in “Washer Maintenance.”

Unload washer as soon as cycle is complete.

Not using HE detergent or using too

much HE detergent.

Use only HE detergent. Be sure to measure correctly.

Always follow the detergent directions.

See “Washer Care” section.

Fabric Damage Sharp items were in pockets during

wash cycle.

Empty pockets, zip zippers, and snap or hook fasteners before

washing to avoid snags and tears.

Strings and straps could have

tangled.

Tie all strings and straps before starting wash load.

Items may have been damaged

before washing.

Mend rips and broken threads in seams before washing.

Fabric damage can occur if the load

is tightly packed.

Load items in loose heaps evenly around washplate.

Load items should move freely during the wash to avoid damage.

Use the cycle designed for the fabrics being washed.

Add only one or two additional items after the washer has

started.

Garment care instructions may not

have been followed.

Always read and follow garment manufacturer’s care label

instructions. See the “Cycle Guide” to match your load with

the best cycle.

Liquid chlorine bleach may have

been added incorrectly.

Do not pour liquid chlorine bleach directly onto load. Wipe up

bleach spills.

Undiluted bleach will damage fabrics. Do not use more than

recommended by manufacturer.

Do not place load items on top of bleach dispenser when

loading and unloading washer.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Troubleshooting

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Incorrect dispenser

operation

Clogged dispensers or laundry

products dispensing too soon.

Do not overﬁll dispenser. Overﬁlling causes immediate dispensing.

Load dispensers before starting a cycle.

It is normal for small amounts of water to be remain in dispenser

at the end of the cycle.

Fabric softener thickens as it gets older. If there becomes an

increase of fabric softener in the dispenser after a cycle, then

check the age of the fabric softener and replace if needed.

Homes with low water pressure may result in residual powder

in the dispenser. To avoid, select a warmer wash temperature

if possible, depending on your load.

Liquid chlorine bleach not used in

dispenser.

Use only liquid chlorine bleach in the bleach dispenser.

Powdered detergent

not dissolving completely

in load

Using too much HE detergent. Follow the manufacturer’s instructions to determine the amount

of detergent to use.

Water temperature is very cold. Select a warmer wash temperature.

Try adding the detergent to the basket prior to adding laundry,

rather than using the detergent dispenser.

Single-dose laundry

packet not dissolving

Adding laundry packet incorrectly. Be sure laundry packet is added to washer basket before adding

clothes. Follow the manufacturer’s instructions to avoid damage

to your items.

Error Code Appears in Display

F#E# code (F-type error

code) appears in display

System error code. Touch the POWER button to clear the code and exit cycle.

Then touch the POWER button, select cycle, and touch and hold

the START/PAUSE button to start washer. If code appears again,

call for service.

F8E1 or LF (too long to

ﬁll) appears in display

Washer taking too long to ﬁll. Drain

extends more than 4.5" (114 mm) into

standpipe.

Check plumbing for correct drain hose installation. Use drain

hose form and attach securely to drainpipe or tub. Do not tape

over drain opening. See Installation Instructions.

Make sure water supply line is turned on.

F9E1, drn, dr (drain

pump system problem –

long drain) appears in

display

Washer taking too long to drain

water. Drain extends more than

4.5" (114 mm) into standpipe.

Check plumbing for correct drain hose installation. Use drain

hose form and attach securely to drainpipe or tub. Do not tape

over drain opening.

Lower drain hose if the end is higher than 96" (2.4 m) above

the ﬂoor. Remove any clogs from drain hose. See Installation

Instructions.

F8E6 (Lid opened)

appears in display

Washer lid left open. Close the lid and touch the POWER button to clear the display.

If the lid is left open for more than 10 minutes, the cycle will reset

and water in the washer will drain.

F1E1 ACU (Appliance

control fault)

Internal ACU failure. Call for service.

F2E3 UI/ACU mismatch Wrong ACU or UI has been installed. Call for service.

F3E1 Water level sensing

failure

Pressure sensor on ACU failure. Call for service.

F5E2 Lid lock will not

lock or lid lock failure

An item in the load may be keeping

the lid from locking.

Check for items directly under the lid.

F5E3 Lid cannot unlock Objects on washer lid keep it from

unlocking.

Remove objects, such as baskets of laundry, from top of washer.

F6E2 or F6E3

Communication Error:

UI cannot communicate

ACU or UI synchronization error. Remove power from the washer. Let washer sit for 5 minutes for

the washer to completely power down. Apply power to washer

and check for error codes. If the error code persists call for

service.

“Ofb” (Off Balance) Load not balanced or evenly

distributed around the basket.

Cycle is paused as indicated by the ﬂashing Start/Pause

indicator. Open the lid, redistribute the load, and close the lid.

Touch and hold the START/PAUSE button to resume.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help –

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

WHIRLPOOL

LAUNDRY

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS

REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

Name, address, and telephone number

Model number and serial number

A clear, detailed description of the problem

Proof of purchase including dealer or retailer name and address

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

11/14

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair.

Some questions can be addressed without service. Please take a few minutes to review the

Troubleshooting or Problem Solver section of the Use and Care Guide, scan the QR code on

the right to access additional resources, or visit https://www.whirlpool.com/product_help.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers.

In the U.S. and Canada, direct all requests for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A. call 1-800-253-1301. In Canada call 1-800-807-6777.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

https://www.whirlpool.com/product_help

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

1. Commercial, non-residential, multiple-family use, or use inconsistent with published user,

operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes, or correction of household electrical or

plumbing (i.e. house wiring, fuses, or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water ﬁlters, preservation solutions,

etc.).

Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.

6. Conversion of your product from natural gas or L.P. gas or reversal of appliance doors.

7. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God, or use with products not

approved by Whirlpool.

8. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration, or modiﬁcation of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to appliance

ﬁnishes unless such damage results from defects in materials and workmanship and is

reported to Whirlpool within 30 days.

10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive

environments, including but not limited to, high salt concentrations, high moisture or

humidity, or exposure to chemicals.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where an authorized

Whirlpool servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (i.e. trim,

decorative panels, ﬂooring, cabinetry, islands, countertops, drywall, etc.) that interfere

with servicing, removal, or replacement of the product.

14. Service or parts for appliances with original model/serial numbers removed, altered, or

not easily determined.

The cost of repair or replacement under these excluded circumstances shall be

borne by the customer.

For one year from the date of purchase,

when this major appliance is installed,

operated, and maintained according

to instructions attached to or furnished

with the product, Whirlpool Corporation

or Whirlpool Canada LP (hereafter

“Whirlpool”) will pay for Factory

Specified Replacement Parts and repair

labor to correct defects in materials or

workmanship that existed when this major

appliance was purchased, or at its sole

discretion replace the product. In the event

of product replacement, your appliance

will be warranted by the remaining term of

the original unit’s warranty period.

YOUR SOLE AND EXCLUSIVE REMEDY

UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be

provided by a Whirlpool designated

service company. This limited warranty

is valid only in the United States or

Canada and applies only when the major

appliance is used in the country in which

it was purchased. This limited warranty

is effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain service

under this limited warranty.

La page est en cours de chargement...

Whirlpool WTW7500GC0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WTW7500GC0

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WTW7500GC0 Owner's manual

Whirlpool WTW7500GC0 Le manuel du propriétaire

Whirlpool WTW7500GC0 Le manuel du propriétaire

dans d''autres langues

Documents connexes