Black Box LES421A Guide de démarrage rapide
- Catégorie
- La mise en réseau
- Taper
- Guide de démarrage rapide
LES421A
1 PORT
HARDENED
SERIAL SERVER
QUICK START GUIDE
24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM
STEP 1 - Check for All Required Hardware
• 1-Port Hardened Serial Server
• This Quick Start Guide
USER-SUPPLIED COMPONENTS
• Network and serial cables (not included)
• Power supply (not included)
STEP 2 - UL C1/D2 Installation Information
UL CLASS 1 / DIVISION 2 WARNING INFORMATION
SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS
A, B, C AND D HAZARDOUS LOCATIONS, OR
NONHAZARDOUS LOCATIONS ONLY.
CONVENANT À L’EMPLOI DANS LES SITES
DANGEREUX DE CLASSE I, DIVISION 2, GROUPES
A, B, C ET D, OU DANS LES SITES NON HASARDEUX
SEULEMENT
WARNING - EXPLOSION HAZARD - SUBSTITUTION
OF ANY COMPONENT MAY IMPAIR SUITABILITY FOR
CLASS I, DIVISION 2.
ATTENTION - DANGER D’EXPLOSION - LA
SUBSTITUTION DE COMPOSANTS PEUT ENTRAÎNER
UNE ADÉQUATION À LA CLASSE I, DIVISION 2.
THE UNIT IS TO BE POWERED BY A CLASS 2 POWER
SOURCE, OF A GROUNDED-TYPE, WHEN POWER IS
APPLIED TO THE BARREL CONNECTOR.
L’UNITÉ DOIT ÊTRE ALIMENTÉE PAR UNE SOURCE
D’ALIMENTATION DE CLASSE 2, DE TYPE MISE À LA
TERRE, LORSQUE LE CONNECTEUR DU CANON EST
ALIMENTÉ.
THE POWER CABLE MUST HAVE A MINIMUM RATING
OF 80°C.
LE CÂBLE D’ALIMENTATION DOIT AVOIR UNE
INDICATION MINIMALE DE 80 °C.
POWER CANNOT BE APPLIED TO BOTH THE
TERMINAL BLOCK AND BARREL CONNECTORS
SIMULTANEOUSLY.
L’ALIMENTATION NE PEUT PAS ÊTRE APPLIQUÉE
SIMULTANÉMENT AUX CONNECTEURS DU BORNIER
ET DU BARILLET.
THE USE OF COAXIAL CABLE FOR THE FIELD WIRING SHALL
BE IN ACCORDANCE WITH CLASS 2/CLASS 3 REQUIREMENTS
IN ARTICLE 725 OF THE NEC.
L’UTILISATION D’UN CÂBLE COAXIAL POUR LE CÂBLAGE SUR
SITE DOIT ÊTRE CONFORME AUX EXIGENCES DE CLASSE 2 /
CLASSE 3 DE L’ARTICLE 725 DU NEC.
ONE CONDUCTOR PER TERMINAL
UN CONDUCTEUR PAR BORNE
USE COPPER WIRE ONLY
UTILISER UNIQUEMENT DU FIL DE CUIVRE
WIRE SIZE: 28 TO 16 AWG
TAILLE DE FIL: 28 À 16 AWG
TIGHTENING TORQUE: 5 KG-CM
COUPLE DE SERRAGE: 5 KG-CM
WIRE TEMPERATURE RATING: 105 °C MINIMUM (SIZED FOR 60
°C AMPACITY)
INDICE DE TEMPÉRATURE DU FIL: 105 °C MINIMUM (CALIBRÉ
POUR 60 °C)
80 °C MAXIMUM SURROUNDING AMBIENT AIR
TEMPERATURE
80 °C TEMPÉRATURE AMBIANTE AMBIANTE MAXIMALE
STEP 3 - Install the Hardware
1. Connect a 10 to 48 VDC (58 VDC max.) power
supply (6.0 W required).
2. Connect the network cable from the serial server to
a network drop using a standard serial cable.
3. Connect the serial device to the RS-232 DB9 or
terminal block serial connector with a straight-
through cable for a DCE device or anull-modem
cable for a DTE device.
NOTE: UL® requires one conductor per terminal, 28 to 16 AWG
copper-wire, tightening torque of 5 kg-cm, and 105° C
rating sized for 60° C ampacity.
LED Status
Ready Blinks if system is operating correctly.
Port 1 ON when port is open; blinks when data present on serial port.
Link ON when device is operating in 100BASE-TX mode.
Blinks when data is present on the Ethernet link.
STEP 4 - LED Status
Hold in Mode Switch for… Result
0 to 2 seconds Initiates a hardware reset.
2 to 10 seconds Enters Console mode.
More than 10 seconds Resets to factory defaults.
STEP 5 - Mode Switch
STEP 6 - Install Black Box Hardened Serial Server software
1. Insert the included CD and it should autostart.
2. Follow the prompts to install the software.
NOTE: Make sure you have administrative rights and disable
firewalls.
1. Open the software. Click “Start—>Programs—>Black
Box—> Serial Server Software.”
2. The “Discovery” page opens.
STEP 7a - Set up Black Box Hardened Serial Server software
OR
STEP 7b - Set up the Web Interface
1. Open a browser and type the IP address of the serial
server into the address bar.
2. When the serial server is found, the “Configuration”
window appears.
3. To configure via the network, select “Network.”
4. If you know the IP address, select “The device is at
this address.” and type in the address. If not, select
“I don’t know the IP address of the device.”
5. Click “Connect.”
STEP 8 - Login
STEP 9 - Set up the Network
STEP 10 - Set up the Serial Port Parameters
1. Click “Port 1 Serial” to open the Serial Port
Parameters page. Select the type of serial
connection between the serial server and the serial
device (RS-232, RS-422, RS-485 2-wire, or RS-485
4-wire).
2. Select the baud rate, data bits, stop bits, parity, and
flow control needed to communicate with the serial
device.
1. The serial server is set at the factory to receive an IP
assignment from a DHCP server. If a DHCP server is
not available on your network, it will default to
169.254.102.39.
2. If this address does not work with your PC, change
your network settings to:
- IP Address = 169.254.102.1
- Subnet Mask = 255.255.255.0
- Default Gateway = 169.254.102.100
3. If you need to use different settings, refer to the
user’s manual for instructions.
1. Click “Login.” (The password is blank from the
factory.) The “General” page appears.
STEP 11 - Set up the Port Network Parameters
1. Click “Port 1” network to open the “Port Network
Parameters” page.
2. Select the type of network protocol you want to
use: TCP, UDP, VCOM, or Paired Mode.
3. If you select TCP, choose whether the Hardened
Serial Server will operate as a client or server, then
configure the required IP address, port number, and
other related parameters.
4. If you select UDP, configure the IP address, port
and other related parameters for the device you
want receive from and send to.
5. If you want the serial server to act as a virtual
communications port for a computer, select VCOM.
This allows your computer to connect to a serial
device on the network as if it were connected to a
physical COM port.
6. If you want the serial server to operate in Paired
Mode with another serial server, select “Paired,”
then configure it as a client or server and set up the
IP address, port number, and other related
parameters (similar to setting up TCP).
STEP 12 - Set up Advanced Parameters
1. If you want to set up Advanced parameters, click
“Advanced” on the Port Network Parameters page.
2. If necessary for your application, select “I want to
control how data packets are sent over the
network,” then set up the Character Count, Forced
Transmit, Intercharacter Timeout, Delimiters, and
Delimiter Removal as required.
3. Click “Next.”
STEP 13 - Save and Logout
1. If you have completed the configuration, click
“Save” to save the configuration to the serial server.
2. To logout, click the “Logout” button.
STEP 14 - Test and Verify Operation
1. Set up serial server as a TCP server on serial port 1.
2. Set serial port to RS-232 on serial port 1.
3. Set to 9600, 8, N, 1 on serial port 1.
4. Loopback serial port 1 by connecting TD to RD.
5. Open a DOS window and type “telnet x.x.x.x yyyy,”
where “x.x.x.x” is the IP address of the serial server
and “yyyy” is the port number of the serial port.
6. Type characters on the keyboard. The characters
should appear in the window. If not, double-check
your settings.
NOTE: To download the user manual, go to www.blackbox.com
COPYRIGHT 2018 BLACK BOX CORPORATION. ALL RIGHTS RESERVED.
Documentation Number: pn710-00045-00_r2_LES421A_2318qsg
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Black Box LES421A Guide de démarrage rapide
- Catégorie
- La mise en réseau
- Taper
- Guide de démarrage rapide
dans d''autres langues
- English: Black Box LES421A Quick start guide