NOCO Gen2 Mode d'emploi

geniuschargers.com

SERIES

User Guide Guide de

l’utilisateur

Guía de

usuario

WELCOME!

Thank you for buying a NOCO Genius® GEN Series On-

Board Battery Charger. SAVE THESE INSTRUCTIONS.

This User Guide contains important safety and operating

instructions.

www.geniuschargers.com

WHAT’S IN THE BOX:

• GEN Series On-Board Battery Charger

• User Guide

• Hardware Kit

CONTACTING NOCO:

Risk of SERIOUS INJURY OR DEATH.

ELECTRICAL SHOCK, EXPLOSION, FIRE, AND EYE

INJURY HAZARDS.

PROTECT YOURSELF AND OTHERS.

1.800.456.6626

[email protected]

30339 Diamond Parkway, #102

Glenwillow, OH 44139

United States of America

Phone:

Email:

Mailing Address:

DANGER

Before use, READ AND UNDERSTAND

Quick Start Guide and Owner’s Manual and

User Guide.

Failure to read and understand this information could

result in SERIOUS INJURY or DEATH.

DO NOT REMOVE OR COVER THIS INFORMATION.

2

ELECTRICAL SHOCK HAZARD

CHARGER IS AN ELECTRICAL DEVICE THAT

CAN SHOCK AND CAUSE SERIOUS INJURY.

DO NOT CUT POWER CORDS.

BATTERY POSTS, TERMINALS, AND RELATED

ACCESSORIES CONTAIN CHEMICALS, INCLUDING

LEAD, KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE CANCER AND BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

ALWAYS WASH YOUR HANDS AFTER HANDLING THESE

PRODUCTS.

DANGER

WARNING

FIRE HAZARD

CHARGER IS AN ELECTRICAL DEVICE THAT

EMITS HEAT AND CAN BURN.

DO NOT COVER CHARGER.

EXPLOSION HAZARD

UNMONITORED, INCOMPATIBLE, OR

DAMAGED BATTERIES CAN EXPLODE IF USED

WITH CHARGER.

DO NOT LEAVE CHARGER UNATTENDED

WHILE IN USE.

DO NOT ATTEMPT TO CHARGE DAMAGED OR FROZEN

BATTERIES.

USE CHARGER ONLY WITH BATTERIES OF RECOMMENDED

VOLTAGE.

OPERATE CHARGER ONLY IN WELL-VENTILATED AREAS.

DO NOT SMOKE OR USE ANY OTHER SOURCE OF

ELECTRICAL SPARK OR FIRE WHEN OPERATING CHARGER.

KEEP CHARGER AWAY FROM COMBUSTIBLE MATERIALS.

EYE INJURY HAZARD

BATTERIES CAN EXPLODE AND CAUSE FLYING

DEBRIS.

BATTERY ACID CAN CAUSE EYE IRRITATION.

WEAR EYE PROTECTION WHEN OPERATING

CHARGER.

AVOID CONTACT WITH EYES AND WASH HANDS

AFTER USING CHARGER.

IN CASE OF EYE CONTACT, FLUSH AFFECTED

AREA WITH PLENTY OF WATER.

WARNING

RISK OF EXPLOSIVE GASES

WORKING IN VICINITY OF A LEAD-ACID

BATTERY IS DANGEROUS. BATTERIES

GENERATE EXPLOSIVE GASES DURING

NORMAL BATTERY OPERATION. FOR THIS

REASON, IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW

THE INSTRUCTIONS EACH TIME YOU USE THE CHARGER.

To reduce risk of battery explosion, follow these instructions

and those published by battery manufacturer and

manufacturer of any equipment intended to be used in vicinity

of battery. Review cautionary markings on these products and

on engine.

Use of an attachment not recommended or sold by the battery

charger manufacturer may result in a risk of re, electric shock, or

injury to persons.

To reduce risk of damage to electric plug and cord, pull by plug rather

than cord when disconnecting charger.

Do not operate charger with damaged cord or plug – replace the cord

or plug immediately.

Do not operate charger if it has received a sharp blow, been dropped,

or otherwise damaged in any way; take it to a qualied service facility.

4

DO NOT USE EXTENSION CORDS unless absolutely

necessary. Using an improper extension cord could result in a

risk of re and electric shock and may result in property damage,

personal injury or death. If extension cord must be used, make

sure that:

1.) The pins on the extension cord plug have the same number,

size, and shape as those of the AC power cord plug on the

charger.

2.) The extension cord is properly wired and is in good electrical

condition.

3.) The wire size is as specied in Table 1 below:

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

TABLE 1:

AC INPUT RATING,

AMPERES*

Equal To

Or Greater

Than

But Less

Than 25

(7.6)

0

2

3

4

5

6

8

10

12

14

16

18

16

14

18

16

14

12

10

8

2

3

4

5

6

8

10

12

14

16

18

20

18

16

14

12

16

14

12

10

8

6

100

(30.5)

50

(15.2) 150

(45.6)

AWG SIZE OF CORD

Length Of Cord, Feet (f)

*If the input rating of a charger is given in watts rather than

amperes, the corresponding ampere rating is to be determined by

dividing the wattage rating by the voltage rating - for example:

1250 watts/125 volts = 10 amperes

Do not disassemble charger; take it to a qualied service facility

when service or repair is required. Incorrect reassembly may

result in a risk of electric shock or re.

To reduce risk of electric shock, unplug charger from outlet

before attempting any maintenance or cleaning. Turning off

controls will not reduce this risk.

EXTERNAL CONNECTIONS TO CHARGER SHALL COMPLY

WITH THE UNITED STATED COAST GUARD ELECTRICAL

REGULATIONS (33CFR183, SUB PART I)

USE THE FOLLOWING PRECAUTIONS WHEN YOU WORK NEAR

LEAD-ACID BATTERIES:

• Someone should be within range of your voice or close enough to

come to your aid if you have an accident.

• Have plenty of fresh water and soap nearby in case battery acid

contacts skin, clothing, or eyes.

• Wear complete eye protection and protective clothing. Avoid touching

your eyes while working near a battery. If battery acid contacts your

skin or clothing, wash immediately with soap and water. If acid enters

an eye, immediately ood the eye with running cold water for at least

ten (10) minutes and seek medical attention as soon as possible.

• Be extra cautious when handling metal tools around a battery. If you

drop a metal tool near a battery it might spark or create a short circuit

between the battery terminals and some other metal part. Either event

may cause a dangerous electrical shock hazard, a re, or even an

explosion, resulting in property damage, personal injury, or death.

• Never smoke or allow an open spark or ame in the vicinity of the

battery or engine.

• Remove all personal items made of metal, such as, rings, bracelets,

necklaces, and watches when working with a lead-acid battery. A lead-

acid battery can produce a short-circuited current high enough to weld

a metal ring or other piece of jewelry, causing a severe burn.

• This battery charger is for charging LEAD-ACID BATTERIES

ONLY. DO NOT USE THE BATTERY CHARGER FOR DRY-

CELL BATTERIES THAT ARE COMMONLY USED WITH HOME

APPLIANCES. THESE TYPES OF BATTERIES MAY BURST AND

MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR

DEATH.

•NEVER charge a frozen battery.

BEFORE CHARGING

• To avoid an electric arc (or spark), turn off or disconnect all of the

accessories in the boat or vehicle. Always remove the cable that is

connected to grounded terminal from battery rst.

• Make sure the area around the battery is well-ventilated while the

battery is being charged. If necessary, use a non-metallic material to

fan away the gas in the area.

• If necessary, clean the battery terminals. Be careful to keep the

corrosion and other debris from coming in contact with your skin or

eyes.

• If the battery is not a sealed battery, add distilled water to each cell (if

necessary) until the battery acid solution reaches the level specied by

battery manufacturer. Do not overll. For a battery without cell caps,

such as a valve regulated lead-acid battery (VRLA), carefully follow

the battery manufacturer’s charging instructions.

• Before charging, carefully read the battery manufacturer’s specic

precautions and recommended rates of charge.

• Determine the voltage of the battery by referring to the boat’s or

vehicle’s owner’s manual and make sure that the battery charger has

6

compatible voltages.

• If using an extension cord, always connect to the battery

charger rst, before connecting to an electrical outlet. When

disconnecting, always disconnect from the electrical outlet rst.

Make sure the electrical outlet is a 120VAC GFCI (Ground Fault

Circuit Interrupt) outlet.

LOCATING BATTERY CHARGER

• Locate the battery charger as far away from the battery as

possible.

• Never place the battery charger directly above the battery; gases

from battery will corrode and damage battery charger.

• When reading electrolyte specic gravity or ling battery, never

allow battery acid to come in contact with the battery charger.

• Do not operate the battery charger in a closed-in area or an area

with restricted ventilation.

• Do not set a battery on top of battery charger.

BATTERY SPECS

The following recommendations should ONLY be considered as

guidelines. Always refer to the battery manufacturer’s recommendations

for battery charging. The GEN Series On-Board Battery Chargers are

suitable for charging all types of 12V lead-acid batteries, including

Wet (Flooded), Gel, MF (Maintenance-Free) and AGM (Absorption

Glass Mat) batteries. The GEN Series On-Board Battery Chargers can

be used on battery sizes from 25 to 230Ah, but can also maintain all

battery sizes.

CONNECTING TO THE BATTERY

Before you connect to the battery(s), make sure that the AC power

plug is not connected to an electrical outlet. DO NOT CONNECT THE

BATTERY CHARGER AC POWER PLUG TO THE ELECTRICAL

OUTLET UNTIL ALL OTHER CONNECTIONS ARE MADE. Make

sure you have identied the correct polarity of the battery terminals on

the battery(s). The POSITIVE battery terminal is typically marked by

these letters or symbols (POS,P,+). The NEGATIVE battery terminal

is typically marked by these letters or symbols (NEG,N,-). If you are

having difculty determining the polarity of the battery terminals,

contact the battery manufacturer before proceeding.

1.) Conrm that you have a 12V battery(s). This battery charger is for

12V LEAD-ACID BATTERIES ONLY.

2.) Connect the POSITIVE (Red) eyelet terminal connector to the

POSITIVE (POS,P,+) battery terminal.

3.) Connect the NEGATIVE (Black) eyelet terminal connector to the

NEGATIVE (NEG,N,-) battery terminal.

4.) Repeat steps 2 and 3 for each battery bank.

5.) When disconnecting the battery charger, disconnect in the reverse

sequence, removing the NEGATIVE rst.

HOW TO START CHARGING

1.) Conrm that you have connected the eyelet terminal connectors

properly.

2.) Connect the battery charger’s AC power plug into a suitable

electrical outlet. DO NOT FACE THE BATTERY WHEN MAKING THIS

CONNECTION.

3.) Charge battery(s) until fully charged. A Green LED will illuminate

solid when the battery is fully charged.

4.) The battery charger can be left connected to the battery at all

times to provide maintenance charging. However, it is good practice to

check the battery periodically.

CHARGER MAINTENANCE

GEN Series On-Board Battery Chargers do not require any

maintenance. Do not attempt to open or repair the battery charger

as it will invalidate the limited warranty. A damp cloth may be used to

clean dust, dirt, or other debris off of the battery charger. BEFORE

ATTEMPTING TO CLEAN THE BATTERY CHARGER, MAKE

SURE YOU REMOVE THE AC POWER PLUG FROM THE POWER

SOURCE.

8

UNDERSTANDING LED LIGHTS

Each battery bank contains two (2) LEDs - a CHARGE LED

and an ERROR LED. The CHARGE LED indicates the charging

process (Red when charging, Green when charged) and the

ERROR LED displays a Reverse Polarity or Error Condition.

To understand the LED Light conguration better, see the chart

below:

When Charging

RED

When Charged

GREEN

Reverse

Polarity

ORANGE

LED LIGHTS EXPLANATION

When the battery is charging, the

CHARGE LED will be illuminated RED.

The CHARGE LED will remain a solid

RED color (not blinking) until the battery is

fully charged.

When the battery is fully charged, the

CHARGE LED will be illuminated GREEN.

The CHARGE LED will remain a solid

GREEN color (not blinking) until either

the battery charger is disconnected or the

battery becomes discharged.

If a Reverse Polarity condition exists, the

ORANGE ERROR LED will illuminate.

This ERROR condition will be displayed

whether the charger is plugged in or

disconnected from an AC power source.

Reverse the battery connections to x

this ERROR.

If an ERROR condition exists, the Charge

LED(s) will ash, and/or the ERROR LED

with illuminate and/or ash. There are

several reasons an ERROR condition

could exist. For help troubleshooting

ERROR conditions, see the section

entitled TROUBLESHOOTING.

Error

Condition

FLASHING

FEATURE OVERVIEW

MULTIPLE BATTERY COMPATIBILITY

(GEN2, GEN3 & GEN4)

Independently charges multiple 12V

batteries

WATERPROOF

100% completely sealed, protects against

extreme working environments & rated

at IP68

FULLY INTERACTIVE

Automatically adjusts itself to changing

current needs

DESIGNED FOR SAFETY

Reverse polarity, short circuit, open circuit,

spark proof, overheat, overcurrent &

overcharge protected

HF/HE SWITCH MODE DESIGN

High-frequency, high-efciency for a

lightweight, compact charger

RAPID CHARGING TECHNOLOGY

Charges batteries 2X faster than traditional

linear battery chargers

VARIABLE INPUT COMPENSATED

100% full charge even with varying A/C

input voltages

RECOVERY MODE

Recovers deeply discharged & sulfated

batteries with pulse charging

MULTIPLE BATTERY CHEMISTRY

Safely charges Wet, Gel, MF & AGM

batteries

10

ABNORMALITY PROTECTION

Automatically shuts “off” if charger remains

in Bulk charge mode for an extended period

of time

SPECIFIC GRAVITY OPTIMIZATION

A stabilizing charge that optimizes the

specic gravity of a battery for increased

performance

IGNITION PROTECTED

Non-igniting and temperature controlled for

safe and worry-free operation

CHARGING TIMES

The time required for the GEN Series to charge a normally discharged

battery is shown below. Deeply discharged batteries may take longer to

charge depending on the depth of discharge (DOD). The charge time is

based on an average depth of discharge to a fully charged battery.

*Note: The above table is for reference purposes only. Actual data may

differ due to battery conditions. The time required to charge a normally

discharged battery is based on an average DOD of 50%.

BATTERY SIZE

(Ah)

APPROXIMATE TIME TO CHARGE*

(Hours)

25

50

60

70

80

90

100

125

150

200

230

1.3

2.5

3.0

3.5

4.0

4.5

5.0

6.3

7.5

10.0

11.5

Step 1 & 2: Analyze & Diagnose

Checks the battery’s initial condition, including voltage, state-of-

charge and health, to determine if the battery is stable before

charging.

Step 3: Recovery

Initializes the Recovery desulfation process (if needed) for deeply

discharged or sulfated batteries by pulsing small amounts of

current.

Step 4: Initialize

Starts the charging process with a gentle (soft) charge.

Step 5: Bulk

Begins the Bulk charging process based on the condition of the

battery and returns 80% of the battery’s capacity.

Step 6: Absorption

Brings the charge level to 90% by delivering small amounts of

current to provide a safe, efcient charge. This limits battery

gassing and is essential to prolonging battery life.

Step 7: Optimization

Finalizes the charging process and brings the battery to maximum

capacity. In this step, the charger utilizes multi-layered charging

proles to fully recapture capacity and optimize the specic

gravity of the battery for increased run time and performance. The

charger will switch to Maintenance if the battery tells the charger

that more current is needed.

Step 8: Maintenance

Continuously monitors the battery to determine when a

maintenance charge should be initiated. If the battery voltage

falls below its target threshold, the charger will restart the

Maintenance cycle until voltage reaches its optimal state and then

discontinues the charge cycle. The cycle between Optimization

and Maintenance is repeated indenitely to keep the battery at

full charge. The battery charger can be safely left connected

indenitely without the risk of overcharging.

CHARGING STEPS

1 2 3 4 5 6 7 8

Analyze

Step

Voltage (V)

Current (A)

Initialize

Diagnose

Bulk

Optimization

Recovery

Absorption

Maintenance

Excluding Cords

12

TECHNICAL SPECIFICATIONS

Battery Banks

Amps/Bank

Total Amps

Input Voltage AC

Working Voltage AC

Nominal Voltage

Efciency

Charging Voltage

Back Current Drain

Ripple

Charger Type

Type of Batteries

Battery Chemistries

Battery Capacity

Housing Protection

Cooling

Output Leads (Length)

AC Cord (Length)

Dimensions (L x W x H)

Weight

GEN1

1

10A

110-120VAC, 50-60Hz

70-130 VAC, 50-60Hz

12VDC

~90%

14.4V

<5mA

<2%

8 Step, Fully Automatic, Switch-Mode

12V Lead-Acid

Wet, Gel, MF & AGM

25-230Ah; Maintains All Battery Sizes

IP68

Natural Convection

6.3 Feet

6.0 Feet

7”x6”x3.3”

6.4lbs

GEN2

2

10A

20A

12VDCx2

8.5”x6.5”x3.3”

8.7lbs

GEN3

3

10A

30A

12VDCx3

11.5”x8.5”x3.25”

14.5lbs

GEN4

4

10A

40A

12VDCx4

15.6lbs

WICKED SMART TIP

BATTERY TESTING AND DIAGNOSTICS. The battery

charger will not begin delivering any current to the battery(s)

until the battery charger detects a ‘stable’ battery. A ‘stable’

battery means the eyelet terminal connectors are connected

to the battery with the correct polarity (POSITIVE-TO-

POSITIVE, NEGATIVE-TO-NEGATIVE) and have a tight,

clean connection to the battery being charged. If the battery

is not stable for at least three (3) seconds, the battery charger

will not begin charging the battery and the battery charger

will go into an ERROR condition. If the battery is connected

in reverse polarity, it is considered an ‘unstable’ battery and

the ERROR LED will illuminate until the ERROR is cleared by

reversing the eyelet terminal connectors.

Excluding Cords

TROUBLESHOOTING

WHEN FLASHING LEDS ILLUMINATE

When the battery charger detects an ERROR condition, The Charge

LED(s) will ash, and/or the ERROR LED with illuminate solid. If you

are seeing this ERROR condition, it could be the result of one of the

following situations:

• BATTERY VOLTAGE INCOMPATIBILITY

Check to make sure you have a 12V battery. This battery charger

is for 12V batteries only. If you attempting to charge a battery that

is other than 12V, it could cause this ERROR condition. Charge the

appropriate battery to resolve this ERROR condition.

• LOW VOLTAGE BATTERY

If the battery voltage is below 2.0VDC (12V), it could cause this

ERROR condition. In this situation, the battery charger has

determined that the battery voltage is too low to begin a normal charge

cycle. To increase the battery voltage and allow the battery charger to

begin charging, you will need to jump start the battery.

• ABNORMALITY PROTECTION

This ERROR condition is the result of the battery charger being in the

Bulk mode for more than eighty (80) hours. This ERROR condition is

the result of a bad battery. To resolve this ERROR condition, take the

battery to a local battery store for an evaluation.

• BLOWN FUSE IN BATTERY CONNECTOR HARNESS

Check the fuse in the battery connector harness. If the fuse in the

battery connector harness has blown, it could cause this ERROR

condition. Replace the fuse with a 15A Automotive Blade Fuse to

resolve this ERROR condition.

• CORROSION ON BATTERY TERMINALS

Check the battery connections for battery corrosion. If battery

corrosion is present on the battery connections, it could cause this

ERROR condition. Remove the battery corrosion to resolve this

ERROR condition.

• LOOSE BATTERY CONNECTIONS

Check the battery connections to the battery. If the battery connections

are loose, it could cause this ERROR condition. Tighten the battery

connections to resolve this ERROR condition.

• SULFATED, DAMAGED, OR WEAK BATTERY

If you have checked all other possible ERROR conditions and cannot

clear the ERROR, it is probably the result of a sulfated, damaged, or

weak battery. To properly diagnose a sulfated, damaged, or weak

battery, take the battery to a local battery store for an evaluation.

The battery store will advise if the battery can be charged or needs

replaced.

14

WICKED SMART TIP

LOW BATTERY. If you have a severely discharged battery,

a battery that is below 9.0VDC, it could be the result of a

defective battery. Batteries that have been severely discharged

as a result of an accidental load should respond quickly when

current is applied to the battery, resulting in a sharp increase in

battery voltage.

WHEN NO LIGHTS COME ON WHEN THE BATTERY

CHARGER IS PLUGGED INTO AN ELECTRICAL OUTLET

• WEAK AC CONNECTION

Check if the AC outlet has power. If the AC outlet has no or limited

power, it could cause this condition. Plug a light into the AC outlet

to check if the outlet has power. If the light is extremely dim, this

could be the result of limited AC power. The battery charger is

designed for use at 70-130VAC. If there is no power or the power

is below 70VAC, locate another AC outlet that has sufcient power

to resolve this ERROR condition.

BULK TIMEOUT

For safety, if the charger is in bulk mode for 41hours it will

automatically stop charging and all LEDs will ash. If this

happens, have the battery tested as it might be defective. To

restart charging, disconnect AC Power and then reconnect.

WICKED SMART FEATURE

ABNORMALITY PROTECTION. If the battery charger is in the

Bulk mode for more than 80 hours, the battery charger will go

into an ERROR condition. This feature prevents damage if the

battery is faulty.

WICKED SMART TIP

TESTING TO SEE IF CHARGER IS CHARGING

Before applying AC power to the charger, measure the battery

voltage with a digital voltmeter and write the value down. Plug

the battery charger into an electrical outlet. Wait at least thirty

(30) seconds and measure the battery voltage again with the

digital voltmeter. The battery voltage should be higher than the

previous value and slowly moving up.

BIENVENUE!

Merci d’avoir acheté le chargeur de batterie intégré

NOCO Genius® GEN Series. CONSERVEZ CES

INSTRUCTIONS. Ce Guide de l’utilisateur contient des

instructions de sécurité et de fonctionnement importantes.

www.geniuschargers.com

QUE CONTIENT LA BOÎTE :

• Un chargeur de batterie intégré GEN Series

• Un Guide de l’utilisateur

• Un kit de quincaillerie

POUR CONTACTER NOCO :

Risques de BLESSURES GRAVES OU MORTELLES.

RISQUES DE DÉCHARGE ÉLECTRIQUE,

D’EXPLOSION, DE FEU ET DE BLESSURES AUX YEUX.

PROTÉGEZ-VOUS ET PROTÉGEZ LES AUTRES

1.800.456.6626

[email protected]

30339 Diamond Parkway, #102

Glenwillow, OH 44139

United States of America

Téléphone :

Courriel :

Adresse postale :

DANGER

Avant d’utiliser ce produit, LISEZ ET

COMPRENEZ le Guide de démarrage rapide,

le Manuel du propriétaire et le Guide de

l’utilisateur.

Omettre de lire et de comprendre ces informations pourrait

entraîner des BLESSURES GRAVES OU MORTELLES.

NE PAS ENLEVER OU COUVRIR CES INFORMATIONS.

16

LE CHARGEUR EST UN APPAREIL

ÉLECTRIQUE QUI PEUT ÉLECTROCUTER ET

PRODUIRE DES BLESSURES GRAVES.

NE COUPEZ PAS LES CÂBLES D’ALIMENTATION

LES BORNES DES BATTERIES, LES TERMINAUX ET LES

ACCESSOIRES S’Y RATTACHANT CONTIENNENT DES

PRODUITS CHIMIQUES INCLUANT LE PLOMB, RECONNU PAR

L’ÉTAT DE LA CALIFORNIE POUR CAUSER LE CANCER, DES

MALFORMATIONS CONGÉNITALES OU AUTRES DOMMAGES

AU FOETUS.

TOUJOURS LAVER VOS MAINS APRÈS AVOIR MANIPULÉ CES

PRODUITS.

DANGER

AVERTISSEMENT

RISQUE DE FEU

LE CHARGEUR EST UN APPAREIL ÉLECTRIQUE

QUI ÉMET DE LA CHALEUR ET QUI PEUT BRÛLER.

NE COUVREZ PAS LE CHARGEUR.

RISQUE D’EXPLOSION

DES BATTERIES ÉTANT SANS SURVEILLANCE,

INCOMPATIBLE OU ENDOMMAGÉE, POURRONT

EXPLOSER SI ELLES SONT UTILISÉES AVEC LE

CHARGEUR.

NE PAS LAISSER LE CHARGEUR SANS

SURVEILLANCE PENDANT L’USAGE.

NE TENTEZ PAS DE CHARGER DES BATTERIES ENDOMMAGÉES

OU GELÉES.

N’UTILISEZ LE CHARGEUR QU’AVEC DES BATTERIES DE TENSION

RECOMMANDÉE.

N’UTILISEZ LE CHARGEUR QUE DANS DES ENDROITS BIEN

AÉRÉS.

NE PAS FUMER OU UTILISER TOUTE AUTRE SOURCE

D’ÉTINCELLE ÉLECTRIQUE OU DE FEU LORSQUE LE CHARGEUR

FONCTIONNE.

GARDEZ LE CHARGEUR ÉLOIGNÉ DES MATIÈRES

COMBUSTIBLES.

RISQUE DE BLESSURES AUX YEUX

LES BATTERIES PEUVENT EXPLOSER ET CAUSER

DES DÉBRIS VOLANTS.

L’ACIDE DE BATTERIE PEUT CAUSER UNE

IRRITATION AUX YEUX.

PORTEZ DES LUNETTES DE PROTECTION

LORSQUE LE CHARGEUR FONCTIONNE.

ÉVITEZ TOUT CONTACT AVEC LES YEUX ET LAVEZ

LES MAINS APRÈS AVOIR UTILISÉ LE CHARGEUR.

EN CAS DE CONTACT AVEC LES YEUX, RINCEZ LA

ZONE AFFECTÉE À GRANDE EAU.

AVERTISSEMENT

RISQUE DE GAZ EXPLOSIFS

TRAVAILLER DANS L’ENCEINTE D’UNE

BATTERIE PLOMB-ACIDE EST DANGEREUX. LES

BATTERIES GÉNÈRENT DES GAZ EXPLOSIFS

LORS D’UN FONCTIONNEMENT NORMAL DE

CELLES-CI. POUR CETTE RAISON, IL EST DE LA PLUS HAUTE

IMPORTANCE QUE VOUS SUIVIEZ LES INSTRUCTIONS

CHAQUE FOIS QUE VOUS UTILISEZ LE CHARGEUR.

Pour réduire un risque d’explosion de la batterie, suivez ces

instructions et celles publiées par le fabricant de la batterie

et le fabricant de tout équipement prévu à être utilisé dans

l’enceinte de la batterie. Lire attentivement les avertissements

indiqués sur ces produits et sur le moteur.

L’utilisation d’un attachement non recommandé ou non vendu par le

fabricant du chargeur de batterie peut entraîner des risques de feu,

décharges électriques ou blessures à d’autres personnes.

Pour réduire le risque de dommage à un connecteur ou une corde

électrique, tirez par le connecteur plutôt que par la corde lors du

débranchement du chargeur.

Ne pas faire fonctionner le chargeur avec un connecteur ou une corde

endommagés — remplacez la corde ou le connecteur immédiatement.

Ne pas faire fonctionner le chargeur si celui-ci a reçu un choc violent, s’il

est tombé ou s’il a été autrement endommagé.

18

N’UTILISEZ PAS DE CORDE DE RALLONGE à moins que ceci soit

absolument nécessaire. L’utilisation d’une corde de rallonge

inadaptée peut entraîner un risque de feu et de décharge électrique

et peut aussi entraîner des dommages à la propriété, des blessures

personnelles ou la mort. Si une corde de rallonge doit être utilisée,

assurez-vous que :

1.) Les broches du connecteur de la corde de rallonge ont le même

nombre, la même taille et forme que celles sur le connecteur de

câble d’alimentation AC du chargeur.

2.) La corde de rallonge est correctement câblée et est en bonne

condition électrique.

3.) La taille du câble est telle que spéciée dans le tableau 1

ci-dessous :

MINIMUM DE TAILLE AWG RECOMMANDÉ POUR

CORDES DE RALLONGE DE CHARGEURS DE BATTERIE

TABLEAU

1

DÉBIT D’ENTRÉE AC,

AMPÈRES*

Égale à ou

plus grande

que

Mais

moins de 7.6

0

2

3

4

5

6

8

10

12

14

16

18

16

14

18

16

14

12

10

8

2

3

4

5

6

8

10

12

14

16

18

20

18

16

14

12

16

14

12

10

8

6

30.515.2 45.6

TAILLE AWG DE LA CORDE

Longueur de la corde, Mètre (m)

*Si le débit d’entrée d’un chargeur est donné en watts plutôt qu’en

ampères, le débit d’ampère correspondant est déterminé en divisant le

nombre de watts par le nombre de voltages — par exemple :

1250 watts/125 volts = 10 ampères

Ne pas démonter le chargeur; apportez-le dans un établissement

de service qualié lorsqu’une réparation est requise. Un remontage

incorrect peut entraîner des risques de décharge électrique ou

d’incendie.

Pour réduire les risques de décharge électrique, débranchez le

chargeur de la prise avant de tenter tout entretien ou nettoyage. La

mise des commandes en position d’arrêt ne réduit pas le risque.

CONNEXIONS EXTERNES CHARGEUR DOIT SE CONFORMER

AUX UNIS DECLARE LA GARDE CÔTIÈRE RÉGLEMENTATIONS

ÉLECTRIQUES (33CFR183, PARTIE SOUS I)

UTILISEZ LES PRÉCAUTIONS SUIVANTES LORSQUE VOUS

TRAVAILLEZ PRÈS DE BATTERIES PLOMB-ACIDE :

• Lorsque vous travaillez à proximité d’une batterie plomb-acide,

quelqu’un doit toujours être à la portée de votre voix ou sufsamment

près pour vous venir en aide si vous avez un accident.

• Ayez toujours de l’eau douce en abondance et du savon près de

vous dans le cas où l’acide de la batterie venait en contact avec la

peau, les vêtements ou les yeux.

• Portez une protection complète pour les yeux et des vêtements

protecteurs. Évitez de toucher vos yeux lorsque vous travaillez près

d’une batterie. Si l’acide de la batterie vient en contact avec votre

peau ou vêtement, lavez immédiatement avec du savon et de l’eau.

Si l’acide entre dans un œil, rincez celui-ci immédiatement avec de

l’eau froide pendant au moins dix (10) minutes et obtenez des soins

médicaux aussitôt que possible.

• Soyez encore plus prudent lorsque vous manipulez des outils en

métal autour d’une batterie. Si vous échappez un outil en métal près

d’une batterie, ceci pourrait créer un court-circuit entre les bornes de

la batterie et une autre partie de métal. Dans les deux cas, un risque

de décharge électrique dangereux, un feu ou même une explosion

pourrait être provoqué, entrainant des dommages, des blessures

personnelles ou la mort.

• Ne jamais fumer ou permettre une étincelle ou une amme nue dans

l’enceinte de la batterie ou du moteur.

• Enlevez tous les effets personnels faits de métal, tels les bagues,

bracelets, colliers et les montres lorsque vous travaillez avec une

batterie plomb-acide. Une batterie plomb-acide peut produire un

courant de court-circuit assez élevé pour fondre une bague en métal

ou autres bijoux, pouvant ainsi causer une brûlure sévère.

• Ce chargeur de batterie est pour charger les BATTERIES

PLOMB-ACIDE SEULEMENT. N’UTILISEZ PAS LE CHARGEUR

DE BATTERIE POUR DES BATTERIES À PILES SÈCHES

COMMUNÉMENT UTILISÉES POUR LES APPAREILS

ÉLECTROMÉNAGERS. CES TYPES DE BATTERIES PEUVENT

ÉCLATER ET CAUSER DES DOMMAGES À LA PROPRIÉTÉ, DES

BLESSURES PERSONNELLES OU LA MORT.

• NE JAMAIS charger une batterie gelée.

AVANT DE CHARGER

• An d’éviter un arc électrique (ou étincelle), fermez ou débranchez

tous les accessoires se trouvant dans le bateau ou le véhicule.

Toujours enlever d’abord le câble qui est branché à la borne de mise à

la terre à partir de la batterie.

• Assurez-vous que la zone autour de la batterie est bien aérée

pendant que la batterie est en mode de charge. Si nécessaire, utilisez

un matériel non métallique pour éventer le gaz de cette zone.

• Si nécessaire, nettoyez les bornes de la batterie. Faites attention

que la corrosion et autres débris ne viennent en contact avec votre

peau ou vos yeux.

La page charge ...

NOCO Gen2 Mode d'emploi

NOCO Gen2 Mode d'emploi

dans d''autres langues