Sollae Systems SIG-5561 Manuel utilisateur

Sollae Systems

https://www.ezTCP.com

PT100 Temperature Sensor Gateway

SIG-5561 User Manual

Version 1.2

SIG-5561 User Manual Ver. 1.2

- 1 -

https://www.ezTCP.com

This symbol, found on your product or on its packaging, indicates that

this product should not be treated as household waste when you wish to

dispose of it. Instead, it should be handed over to an applicable collection

point for the recycling of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help prevent potential negative

consequences to the environment and human health, which could otherwise be caused by

inappropriate disposal of this product. The recycling of materials will help to conserve

natural resources. For more detailed information about the recycling of this product,

please contact your local city office, household waste disposal service or the retail

store where you purchased this product.

Note:

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

SIG-5561 User Manual Ver. 1.2 
 
- 2 - 
https://www.ezTCP.com 
 
Contents 
Overview ....................................................... - 4 - 
1 Introduction ........................................................ - 4 - 
2 Features ............................................................ - 4 - 
3 Specification ....................................................... - 5 - 
4 Interface ........................................................... - 6 - 
4.1 Power .................................................................. - 6 - 
4.2 Ethernet ............................................................... - 7 - 
4.3 PT100 Connection Port .................................................. - 7 - 
4.4 LED .................................................................... - 8 - 
4.5 Function Button ........................................................ - 9 - 
4.6 Setup Port ............................................................. - 9 - 
Preparation ................................................... - 10 - 
1 Installing the Setting Tool ........................................ - 10 - 
2 Connecting a Product ............................................... - 10 - 
3 Searching Devices .................................................. - 10 - 
4 Logging in ......................................................... - 10 - 
Settings ...................................................... - 11 - 
1 Network ............................................................ - 11 - 
1.1 Obtain an IP address automatically ..................................... - 11 - 
1.2 Use a Static IP address................................................ - 12 - 
2 General ............................................................ - 13 - 
2.1 Comment ............................................................... - 13 - 
2.2 Mode .................................................................. - 13 - 
3 Security ........................................................... - 14 - 
3.1 Password .............................................................. - 14 - 
3.2 Certificate ........................................................... - 14 - 
3.3 spFinder .............................................................. - 14 - 
3.4 Client ID ............................................................. - 15 - 
Management .................................................... - 16 - 
1 Checking Status .................................................... - 16 - 
1.1 Product Information ................................................... - 16 - 
1.2 Communication Status .................................................. - 17 - 
1.3 Timeout ............................................................... - 18 - 
1.4 Copy Status ........................................................... - 18 - 
2 Firmware Change .................................................... - 19 - 
2.1 Online Upgrade ........................................................ - 19 - 
2.2 Manual Upgrade ........................................................ - 20 - 
3 Console ............................................................ - 21 - 
3.1 Output Tab ............................................................ - 21 - 

SIG-5561 User Manual Ver. 1.2

- 3 -

https://www.ezTCP.com

4.3.2 FW Log Tab ............................................................ - 21 -

4.3.3 Timeout ............................................................... - 22 -

4.4 Export/Import Setting Values ....................................... - 22 -

4.5 Factory Reset ...................................................... - 23 -

5 Technical Support and Warranty ................................ - 24 -

5.1 Technical Support .................................................. - 24 -

5.2 Warranty ........................................................... - 24 -

5.2.1 Free Repair Services .................................................. - 24 -

5.2.2 Charged Repair Services................................................ - 24 -

6 Precaution and Exemption from Liability ....................... - 25 -

6.1 Precaution ......................................................... - 25 -

6.2 Exemption from Liability ........................................... - 26 -

6.2.1 English version ....................................................... - 26 -

6.2.2 French version ........................................................ - 27 -

7 Revision History .............................................. - 29 -

SIG-5561 User Manual Ver. 1.2

- 4 -

https://www.ezTCP.com

1 Overview

1.1 Introduction

SIG-5561 is an industrial PT100 Temperature Sensor Gateway. This product

consisting of a PT100 connection port and an FND(Flexible Numeric Display) for

displaying a temperature. The device measures temperature and sends it to Sollae

Cloud. Users can remotely monitor the temperature measured by the sensor from

anywhere via any web browser.

Figure 1-1 Diagram

1.2 Features

⚫ PT100 connection port: support 3-wire PT100 sensors

⚫ Display: a red 3-digit 7-segment LED

⚫ Measurement Range: -200℃ ~ 850℃ (-328℉ ~ 1562℉)

⚫ Measurement Error: within ±0.3℃ (±0.54℉)

⚫ Protocol: MQTT (over TLS 1.2)

⚫ Secure (TLS mutual authentication)

⚫ Configurable thresholds to trigger relays on SIG-5451, SIG-5601 devices

⚫ Configurable thresholds to trigger an alarm on web

⚫ Connected to Sollae Cloud

⚫ Widget-based visualization (dashboard)

⚫ Customizable graphic visualization by Sollae Studio

⚫ Industrial temperature range (-40℃ ~ +85℃)

SIG-5561 User Manual Ver. 1.2

- 5 -

https://www.ezTCP.com

1.3 Specification

Analog Input

Input Type

3-wire PT100 sensor (α=0.00385 Ω/(Ω·°C))

Resolution

16 bits

Number of Ports

1 port

Network Physical Interface

Network Interface

10Base-T/100Base-TX Ethernet (RJ45)

Ethernet Speed Auto Sense

1:1 or Cross-over Cable Auto Sense

Software Functions

Protocols

IPv4/IPv6 Dual Stack,

TCP/UDP, ICMP, DHCP, mDNS, MQTT, SSL/TLS

Indicators

LED

PWR, RUN, 3-digit 7-segment LED

Management

spFinder

Configuration and Monitoring Tool

Security

Password

Dimension

Size

94mm x 57mm x 24mm

Weight

about 64g

Operating Environment

Input Voltage

DC5V±0.25V

Protection

Reverse Voltage Protection / Surge Protection

Current Consumption

typically, 250mA

Operating Temperature

-40℃ ~ +85℃

Storage Temperature

-40℃ ~ +85℃

Certificate

KC

Registration (KN 32, KN 35)

CE

EMC 2014/30/EU, RoHS 2011/65/EU

FCC

FCC Part 15 Subpart B, Class A

Table 1-1 Specification

SIG-5561 User Manual Ver. 1.2

- 6 -

https://www.ezTCP.com

1.4 Interface

Figure 1-2 Interface

1.4.1 Power

SIG-5561 requires DC5V power supply whose specification is as follows:

Figure 1-3 Power

SIG-5561 User Manual Ver. 1.2

- 7 -

https://www.ezTCP.com

1.4.2 Ethernet

SIG-5561 provides 10/100Mbps Ethernet. The pin assignment is as follows:

Figure 1-4 Ethernet

1.4.3 PT100 Connection Port

This port is interfaced with a 3.5mm pitch 3-pole terminal block. How to connect a

PT100 sensor to this port is as follows:

Figure 1-5 Connection with a PT100 sensor

⚫ Port Specification

Division

Value

Sensor Type

3-wire PT100 (α=0.00385 Ω/(Ω·°C))

Measuring Range

-200℃ ~ 850℃ (-328℉ ~ 1562℉)

Table 1-2 Port Specification

SIG-5561 User Manual Ver. 1.2

- 8 -

https://www.ezTCP.com

1.4.4 LED

SIG-5561 provides 4 LEDs for indicating status.

Figure 1-6 4 LEDs

LED operations according to each state are as follows:

When the supplied power is stable: PWR

When the supplied power is NOT stable: PWR

When the script is running: RUN

When the script is NOT running: RUN

When a network is NOT connected: LINK

When a network is connected: LINK

When The device cannot connect to the cloud: STS

When the device connected to the cloud but unregistered: STS

When the device connected to the cloud: STS

SIG-5561 User Manual Ver. 1.2

- 9 -

https://www.ezTCP.com

1.4.5 Function Button

This button is used to implement a factory reset.

1.4.6 Setup Port

This port is used for making a connection with a PC via USB cable.

SIG-5561 User Manual Ver. 1.2

- 10 -

https://www.ezTCP.com

2 Preparation

2.1 Installing the Setting Tool

You need a program which is called spFinder to use this product. Download the

program on our web site and install it on your PC.

Functions of the spFinder are as follows:

⚫ Searching products connected via network and USB

⚫ Setting products

⚫ Monitoring status of products

2.2 Connecting a Product

Connect a product with your PC via a LAN cable or a USB cable. In the case of

using a LAN cable, note that your PC and the product should be on the same local

area network.

2.3 Searching Devices

Run spFinder on your PC and press the search button. If you select the product

found, the setup menu appears on the right.

2.4 Logging in

Before accessing the searched product, you need to log in first. The default ID

and password are as follows:

Division

Default Values

ID

sig-5561

Password

sig-5561

Table 2-1 The default values of ID and password



If you search the product via network and it has the default value for a password,

spFinder automatically processes the login.

SIG-5561 User Manual Ver. 1.2

- 11 -

https://www.ezTCP.com

3 Settings

3.1 Network

3.1.1 Obtain an IP address automatically

This product can automatically obtain an IP address by DHCP. A DHCP server is

required to use this.

Figure 3-1 Obtain an IP address automatically

⚫ Select the [Obtain an IP address automatically].

⚫ Check the [Obtain DNS server address automatically] and click the [Save]

button.

SIG-5561 User Manual Ver. 1.2

- 12 -

https://www.ezTCP.com

3.1.2 Use a Static IP address

You can set a static IP address to this product.

Figure 3-2 Use a static IP address

⚫ Select the [Use static IP address].

⚫ Set the [Local IP address], [Subnet mask], [Gateway IP address] and [DNS IP

address].

⚫ Click the [Save] button.

SIG-5561 User Manual Ver. 1.2

- 13 -

https://www.ezTCP.com

3.2 General

Figure 3-3 General

3.2.1 Comment

This setting is for storing the product description. The maximum setting size of

this item is 32 bytes.

3.2.2 Mode

This setting is for selecting the temperature unit between Celsius and Fahrenheit.

SIG-5561 User Manual Ver. 1.2

- 14 -

https://www.ezTCP.com

3.3 Security

ss

Figure 3-4 Security

3.3.1 Password

Both ID and password are required to access this product. Note that changing the

default password to another is highly recommended for security. The password should

be longer than 8 characters.

⚫ Input a password to use to [Password] and [Confirm password].

⚫ Click the [Save] button.

3.3.2 Certificate

The TLS certificates are pre-stored on the device. Please do not change them.

Without certificates or with unauthorized certificates, the device is refused to

connect to Sollae Cloud.

3.3.3 spFinder

These items are related to spFinder use.

⚫ Local search

If this item is not checked, you will not be able to search for or connect to

the product on your local network. This item can be set only when the product

is connected via USB.

⚫ Network connection

If this item is not checked, the product cannot be searched on the local

network and the product cannot be connected on the local or remote network.

This item can be set only when the product is connected via USB.

SIG-5561 User Manual Ver. 1.2

- 15 -

https://www.ezTCP.com

⚫ Remote access

If this item is checked, the product can be connected from the remote network.

For security, this item is unchecked by default.

3.3.4 Client ID

The client ID is used to register the device on Sollae Cloud. See how to register

the device on Sollae Cloud.

SIG-5561 User Manual Ver. 1.2

- 16 -

https://www.ezTCP.com

4 Management

4.1 Checking Status

This is a function to view the current status of the product. Information in the

[Status] window is automatically updated every second. After searching and

connecting the product with spFinder, press the [Status] button to display this

window. When you open this window, the spFinder connects to the product and keeps

the connection until you close the window or time out. While the connection is

maintained, other hosts cannot access the product using the spFinder.

4.1.1 Product Information

⚫ Product Information Window

This area shows some major information of your product.

Figure 4-1 Product Information Window

⚫ Product Information List

Item

Description

Product name

Pkgware

Model name, package version, Firmware version

File name

Uptime

Elapsed time since it boots up (day / hour:min:sec)

IPv4

Assigned IPv4 address

Subnet

Assigned subnet mask

Gateway

Assigned gateway IP address

DNS

Assigned DNS server IP address

Table 4-1 Product Information List

SIG-5561 User Manual Ver. 1.2

- 17 -

https://www.ezTCP.com

4.1.2 Communication Status

⚫ Communication Status Window

This area shows some communication status of your product. This area is

refreshed every second.

Figure 4-2 Communication Status Window

⚫ REGISTRATION STATE

Status

Description

checking

Obtaining information from Cloud

unregistered

The device is not registered to any account

registered

The device is registered under an account

Table 4-2 REGISTRATION STATE

⚫ SSL STATE

Status

Description

SSL CLOSED

Not connected to the cloud

SSL CONNECTED

Connected to the cloud

SSL

CONNECTING

Connecting to the cloud

SSL CLOSING

Disconnecting from the cloud

Table 4-3 SSL STATE

SIG-5561 User Manual Ver. 1.2

- 18 -

https://www.ezTCP.com

⚫ DEVICE STATE

Item

STARTING

UPDATING INFORMATION TO CLOUD

FAILED TO UPDATE INFORMATION TO CLOUD

DEVICE IS UNREGISTERED TO AN USER

CONNECTING MQTT SERVER

FAILED TO CONNECT TO MQTT SERVER

MQTT CLOSED

MQTT CONNECTED TO CLOUD

MQTT PING TO CLOUD

DELAYING BEFORE RECONNECTING

UPGRADING PKGWARE

CERTS FAILED

Table 4-4 DEVICE STATE

⚫ TEMPERATURE

Item

Description

A number

Current temperature

E01

Internal error

E02

Internal error

E03

RTD is not connected to the device

E04

RTD is not connected properly to the device

Table 4-5 TEMPERATURE

4.1.3 Timeout

This is the timeout display function that appears in the upper right of the status

window. When this time reaches zero, the connection between spFinder and the product

is lost. The initial value is 30 minutes. If you move the mouse pointer in the

internal area of the status window, the timer is reset to the initial value again.

4.1.4 Copy Status

Clicking the button copies all information displayed in the current status window

to the clipboard.

SIG-5561 User Manual Ver. 1.2

- 19 -

https://www.ezTCP.com

4.2 Firmware Change

New firmware can be released when adding functions or fixing bugs. If you are

using old firmware, you can upgrade it to the latest version. Firmware can be

upgraded online or manually via spFinder.

4.2.1 Online Upgrade

If you can access to the Internet by your PC, the Firmware can be upgraded online.

Figure 4-3 Online Upgrade

⚫ Search and Connect to your product by spFinder.

⚫ Click [Advanced] > [Firmware change] menu.

⚫ Click [Upgrade] button selecting [Automatic online upgrade] menu.

La page charge ...

Sollae Systems SIG-5561 Manuel utilisateur

Sollae Systems SIG-5561 Manuel utilisateur

dans d''autres langues