Samsung 650 Manuel utilisateur

Thank you for purchasing this Samsung product.

To receive more complete service, please

register your product at

www.samsung.com/global/register

Model Serial No.

imagine the possibilities

Plasma TV

user manual

BN68-01532B-02

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Comment contacter Samsung dans le monde

Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service

Consommateurs Samsung.

Country

Customer Care Center 

Web Site Address

CANADA 1-800-SAMSUNG (7267864) www.samsung.com/ca

Samsung Electronics Canada Inc., Customer Service 55

Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc., Service à la Clientèle

55 Standish Court Mississauga, Ontario L5R 4B2

Canada

U.S.A 1-800-SAMSUNG (7267864) www.samsung.com

Samsung Electronics America, Inc. 105 Challenger Road

Ridgefield Park, NJ 07660-0511

BN68-01532B-Eng.indb 1 2008-05-30 오후 2:31:47

English - 2

Important Warranty Information Regarding Television Format Viewing

Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide

screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format,

or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary

graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and

programming, should be limited to no more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos,

web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary

images that exceed the above guidelines can cause uneven aging of PDP Displays that leave subtle, but permanent

burned-in ghost images in the PDP picture. To avoid this, vary the programming and images, and primarily display

full screen moving images, not stationary patterns or dark bars.

On PDP models that offer picture sizing features, use these controls to view different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a result of format

selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.

➢

See the warranty card for more information on warranty terms.

U.S.A Only

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain

third parties. In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484,

5,214,678, 5,323,396, 5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247,

5,960,037, 6,023,490, 5,878,080, and under US Published Patent Application No. 2001-44713-A1.

This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are

granted for commercial use. The license does not cover any product unit other than this product unit and the license

does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or

sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode

audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product

features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Other countries

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third

parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights

are granted for commercial use. The license does not cover any product unit other than this product unit and the license

does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or

sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode

audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product

features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with

Samsung Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained

herein, SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products

purchased in Canada, and in Canada on SAMSUNG products purchased in the United States, for the warranty period

originally specified, and to the Original Purchaser only.

The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this

Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to

the Service Center. Transportation to and from the Service Center is the responsibility of the purchaser.

Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in

normal use of the product.

Excluded, but not limited to, are any originally specified provisions for, in-home or on-site services, minimum or

maximum repair times, exchanges or replacements, accessories, options, upgrades, or consumables.

For the location of a SAMSUNG Authorized Service Center, please call toll-free:

In the United States : 1-800-SAMSUNG (1-800-726-7864) In Canada : 1-800-SAMSUNG

BN68-01532B-Eng.indb 2 2008-05-30 오후 2:31:47

English - 3

User Instructions

Screen Image retention

Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can

cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, refer to

page 32 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still image.

Altitude

The PDP can only operate normally at heights under 6500ft.

Heat on the top of the Plasma TV

The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in

the upper part of the product.

This is normal and does not indicate any defect or operation failure of the product.

However, children should be prevented from touching the upper part of the product.

The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as

temperature or humidity. This is normal and not a defect of the unit.

Cell Defects

The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated

technology to produce. However, there may be a few bright or dark pixels on the screen. These pixels will have no impact

on the performance of the product.

Avoid operating the TV at temperatures below 5°C (41°F)

A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the Plasma TV in 4:3 format for a long period of time may leave traces of borders

displayed on the left, right and center of the screen caused by the difference of light emission on

the screen.

Playing a DVD or a game console may cause similar effects to the screen.

Damages caused by the above effect are not covered by the Warranty.

After-images on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a long time.

Warranty

Warranty does not cover any damage caused by image retention.

Burn-in is not covered by the warranty.

BN68-01532B-Eng.indb 3 2008-05-30 오후 2:31:47

English - 4

Symbols

Press

One-Touch

Button

➢

Note

Contents

English

General Information

■ List of Features .............................................................5

■ Accessories ...................................................................5

■ Viewing the Control Panel .............................................6

■ Viewing the Connection Panel ......................................7

■ Remote Control .............................................................8

■ Installing Batteries in the Remote Control .....................9

Connections

■ Connecting VHF and UHF Antennas ............................9

■ Connecting Cable TV ..................................................10

■ Connecting a DVD Player or Cable Box / Satellite

receiver (Set-Top Box) via HDMI ................................ 11

■ Connecting a DVD Player or Cable Box / Satellite

receiver (Set-Top Box) via DVI .................................... 11

■ Connecting a DVD Player or Cable Box / Satellite

receiver (Set-Top Box) via Component cables ............12

■ Connecting a Camcorder ............................................12

■ Connecting a VCR ......................................................13

■ Connecting a Digital Audio System .............................14

■ ConnectinganAmplier/DVDHomeTheater ...........14

■ Connecting a PC .........................................................15

Operation

■ Turning the TV On and Off ..........................................16

■ Plug & Play Feature ....................................................16

■ Changing Channels ....................................................18

■ Adjusting the Volume ..................................................19

■ Viewing the Display .....................................................19

■ Viewing the Menus ......................................................19

■ Using the Remote Control Backlight Buttons ..............20

■ Using the TOOLS Button ............................................20

■ Memorizing the Channels ...........................................20

■ To Select the Source ...................................................22

■ To Edit the Input Source Name ...................................22

Picture Control

■ Changing the Picture Standard ...................................23

■ Customizing the Picture Settings ................................23

■ Adjusting the Detailed Settings ...................................24

■ ConguringPictureOptions .......................................27

■ Resetting the Picture Settings to the Factory Defaults 34

■ Viewing Picture-in-Picture ...........................................34

Sound Control

■ Changing the Sound Standard ....................................36

■ Customizing the Sound ...............................................36

■ Setting the TruSurround XT ........................................37

■ Choosing Preferred Language ....................................38

■

Choosing a Multi-Channel Sound (MTS) Track - Analog

.38

■ Automatic Volume Control ..........................................39

■ Setting the TV Speakers On/Off..................................39

■ Listening to the Sound of the Sub (PIP) Picture .........40

■ Resetting the Sound Settings to the Factory Defaults 40

■ Connecting Headphones (Sold separately) ................40

Channel Control

■ Managing Channels ....................................................41

■ Clearing Scrambled Channels - Digital .......................47

■ Fine Tuning Analog Channels .....................................47

■ Checking the Digital-Signal Strength ..........................48

PC Display

■ Using Your TV as a Computer (PC) Display ...............49

■ Display Modes ............................................................49

■ Setting up the TV with your PC ...................................50

Time Setting

■ Setting the Time ..........................................................52

Function Description

■ Selecting a Menu Language .......................................56

■ Using the V-Chip .........................................................57

■ Viewing Closed Captions (On-Screen Text Messages)

- Digital ........................................................................65

■ Viewing Closed Captions (On-Screen Text Messages)

- Analog .......................................................................66

■ Adjusting the TV On/Off Melody Sound ......................67

■ Setting the Entertainment mode .................................68

■ Using the Energy Saving Feature ...............................68

■ Upgrading the Software ..............................................69

WISELINK

■ Using the WISELINK Function ....................................70

■ Using the Photo List ....................................................71

■ Viewing a Photo or Slide Show ...................................77

■ Using the Music List ....................................................81

■ Playing a Music File ....................................................86

■ Using the Setup Menu ................................................88

Network Settings and InfoLink

■ Network Connection - Cable .......................................89

■ Network Connection - Wireless ...................................91

■ Network selection ........................................................91

■ Cable Network Setup ..................................................92

■ Wireless Network Setup ..............................................94

■ Using InfoLink .............................................................97

■ InfoLink Setup ...........................................................100

About Anynet

+

■ What is Anynet

+

? ......................................................101

■ Connecting Anynet

+

Devices ....................................101

■ Setting Up Anynet

+ ...................................................102

■ Scanning and Switching between Anynet

+

Devices .102

■ Recording ..................................................................103

■ Listening through a Receiver (Home theater) ...........104

■ Troubleshooting for Anynet

+ .....................................104

Appendix

■ Securing the TV to the Wall ......................................105

■ Troubleshooting ........................................................106

■ Auto Wall-mount adjustment (Sold separately)

(PN50A650T1F) ........................................................107

■ WallMountKitSpecications(VESA) .......................108

■ Preparing before installing Wall- Mount on the wall ..109

■ How to attach the Stand-Base ..................................109

■ Specications ............................................................ 110

■ Dimensions (PN50A650T1F) .................................... 111

■ Dimensions (PN58A650T1F) .................................... 112

BN68-01532B-Eng.indb 4 2008-05-30 오후 2:31:47

English - 5

General Information

List of Features

• Adjustable picture settings that can be stored in the TV’s memory.

• Automatic timer to turn the TV on and off.

• A special sleep timer.

• V-Chip function.

• Excellent Digital Interface & Networking :

With

a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver (Set-

Top Box) needed.

• HDMI/DVI connection of your PC to this TV.

• Excellent Picture Quality

-

DNIe technology provides life-like clear images.

• SRS TruSurround XT

-

SRS TruSurround XT provides a virtual surround system.

Accessories

Please make sure the following items are included with your TV. If any items are missing, contact your dealer.

Remote Control

(BN68-00695A) /

AAA Batteries (4301-000103)

Power Cord

(3903-000144)

Owner’s Instructions /

Quick Setup Guide

Warranty Card /

Safety Guide Manual

(Not available in all locations)

Cleaning Cloth

(BN63-01798B)

Cover-Bottom /

Screws (2ea)

(Refer to page 110)

Ferrite Core for Power Cord

(3301-001305)

PN50A650T1F

only: 5ea

PN58A650T1F

only:

3ea

➢

See the bottom of the page for Ferrite Core usage.

The following parts are sold separately and are available at most electronics stores.

➢

If you do not use a good quality cable, some noise may appear on the screen.

S-VIDEO Cable (BN39-00149A) HDMI Cable (BN39-00641A) HDMI/DVI cable (BN39-00643A) Component Cables (RCA)

(BN39-00279A)

PC Cable (BN39-00115A) PC Audio Cable (BN39-00061B) Optical Cable Antenna Cable (BN39-00333A)

➢

Ferrite Core

The ferrite cores are used to shield the

cables from interference.

When

connecting a cable, open the

ferrite core and clip it around the cable

near the plug.

Power Cord

(PN58A650T1F

only)

Power Cord

(PN50A650T1F

only)

S-Vídeo Cable

Component

Cable

Side HDMI Cable/ Audio Cable

/ Video Cable (PN50A650T1F only)

BN68-01532A-Eng(01-37).indd 5 2008-05-30 오후 3:18:51

English - 6

Viewing the Control Panel

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

1

SOURCE

Toggles between all the available input sources

(TV, AV1, AV2, S-Video, Component1, Component2,

PC, HDMI1, HDMI2/DVI, HDMI3, HDMI4, USB).

➢

In the on-screen menu, use this button as you

would use the ENTER button on the remote control.

2

MENU

Press to see an on-screen menu of your TV’s features.

3

+ VOL –

Press to increase or decrease the volume. In the on-

screen menu, use the + VOL

–

buttons as you would

use the ◄ and ► buttons on the remote control.

4

CH

Press to change channels.

In the on-screen menu, use the CH buttons as

you would use the ▲ and ▼ buttons on the remote

control.

5

Power Indicator

Lights up when the power is on.

6

POWER

Pr

ess to turn the TV on and off.

7

Remote Control Sensor

Aim the remote control towards this spot on the TV.

8

Speakers

➢

The product color and shape may vary depending on the model.

Front Panel buttons

Touch each button to

operate.

BN68-01532B-Eng.indb 6 2008-05-30 오후 2:31:50

English - 7

Viewing the Connection Panel

Rear Panel Jacks

Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players. For

more information on connecting equipment, see pages 9-15. The product color and shape may vary depending on the model.

1

POWER IN

Connect the supplied power cord.

2

LAN

Connect a LAN cable to this port to connect to the

Network (SAMSUNG's InfoLink Service). (See page 89)

3

AUDIO OUT (R/L)

Audio outputs to external devices.

4

PC IN[PC]/[AUDIO]

Connect to the video and audio output jack on your PC.

5

DVI IN (HDMI 2) (AUDIO-R/L)

Connect to the DVI audio output jack of an external device.

6

HDMI IN 1, 2, 3

Connect to the HDMI jack of a device with an HDMI

output. (HDMI 2 supports HDMI-DVI IN and connection

from a PC.)

- This input can also be used as a DVI connection with

separate analog audio inputs. An optional HDMI/DVI

cable will be necessary to make this connection.

-

When using an optional HDMI/DVI adapter, the DVI

analog audio inputs on your TV allow you to receive left

and right audio from your DVI device.

7

ANT IN

 Usesa75ΩCoaxialconnectorforanAir/Cable

Network.

8

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio component.

9

COMPONENT IN 1, 2 / AV IN 1

Connects Component video/audio.

The COMPONENT IN 1 jack is also used as the AV IN 1

jack.

- Connect the video cable to the COMPONENT IN 1 [Y/

VIDEO] jack and the audio cable to the COMPONENT IN 1

[R-AUDIO-L] jacks.

0

EX-LINK

Connect this to the jack on the optional wall mount

bracket. This will allow you to adjust the TV viewing

angle using your remote control.

Side Panel Jacks

Use the right side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game.

The product color and shape may vary depending on the model.

1

HDMI IN 4

Connect to the HDMI jack of a device with an HDMI output.

2

WISELINK

Connect a USB mass storage device to view photo files (JPEG) and play audio files (MP3).

3

S-VIDEO (AV IN 2)

S-Video input for external devices with an S-Video output.

4

AV IN 2

Video and audio inputs for external devices.

5

HEADPHONE

You can connect a set of headphones if you wish to watch a television program without

disturbing other people in the room.

BN68-01532B-Eng.indb 7 2008-05-30 오후 2:31:51

English - 8

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

➢

The performance of the remote control may be affected by bright light.

1

POWER

Turns the TV on and off.

2

TV

Selects the TV mode directly.

3

NUMERIC BUTTONS

Press to change the channel.

4

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

Press to select additional channels

(digital and analog) being broadcast

by the same station. For example,

to select channel “54-3”, press “54”,

then press “

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

” and “3”.

5

MUTE

Press to temporarily cut off the

sound.

6

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

VOL

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

Press to increase or decrease the

volume.

7

SOURCE

Press to display and select the

available video sources.

8

CH LIST

Used to display Channel Lists on the

screen.

9

TOOLS

Use to quickly select frequently used

functions.

0

UP▲/DOWN▼/LEFT◄/

RIGHT►/ENTER

Press the Up/Down/Left/Right

sections of the wheel button and

Enter to select on-screen menu

items and change menu values.

You can navigate up and down the

menu, switch channels and adjust

the volume by turning the wheel

button. (See pages 18~19)

While using the MENU, TOOLS,

and WISELINK, the wheel function

starts the power saving mode if idle

for more than 20 seconds. Press the

wheel button to disable the power

saving mode.

!

INFO

Press to display information on the

TV screen.

@

COLOR BUTTONS

Use these buttons in the Channel list

and WISELINK, etc.

#

CC

Controls the caption decoder.

$

E.MODE

Press to select the preset display

and sound modes for sports, cinema

and games.

%

Use these buttons in the DMA,

WISELINK and Anynet+ modes.

(

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

: This remote can be used

to control recording on Samsung

recorders with the Anynet+ feature)

^

ON/OFF

Press to backlight the buttons on the

remote.

This function is convenient for using

at night or when the room is dark.

(Using the remote control with the

ON/OFF( ) light button set to On

will reduce the battery usage time.)

&

PRE-CH

Tunes to the previous channel.

*

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

CH

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

Press to change channels.

(

MENU

Displays the main on-screen menu.

)

W.LINK(WISELINK)

This function enables you to view

and play photo and music files from

an external device. (Refer to pages

71 (Photo) and 81 (Music))

a

RETURN

Returns to the previous menu.

b

EXIT

Press to exit the menu.

c

INFO.L

Press to use the News, Stock

Market and Weather Forecast

information services available over

the network.

(see page 97)

d

DMA (Digital Media Adapter)

Use this when connecting a

Samsung DMA device through an

HDMI interface and switching to

DMA mode.

For more information on the

operating procedures, refer to the

user manual of the DMA.

➢

This button is available when

“Anynet+(HDMI-CEC)” is “On”.

(see page 102)

e

P.SIZE

Picture size selection.

f

FAV.CH

Press to switch to your favorite

channels.

BN68-01532B-Eng.indb 8 2008-05-30 오후 2:31:51

English - 9

Connections

Connecting VHF and UHF Antennas

Ifyourantennahasasetofleadsthatlooklikethis,see“Antennaswith300ΩFlat

Twin Leads” below.

Ifyourantennahasoneleadthatlookslikethis,see“Antennaswith75ΩRound

Leads”.

If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennaswith300ΩFlatTwinLeads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that

has300Ωtwinflatleads,followthedirectionsbelow.

1 Placethewiresfromthetwinleadsunderthescrewsona300-75Ωadapter(not

supplied).

Use a screwdriver to tighten the screws.

2 Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

1

Plug the antenna lead into the ANT IN terminal on the back of the TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must

combine the two antenna signals before connecting the antennas to the TV. This

procedure requires an optional combiner-adaptor (available at most electronics

shops).

1 Connect both antenna leads to the combiner.

2 Plug the combiner into the ANT IN terminal on the bottom of the back panel.

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as shown in the figure.

2 Install two AAA size batteries.

➢

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the

compartment.

➢

Using the remote control with the ON/OFF( ) light button set to On will reduce the

battery usage time.

3 Close the cover as shown in the figure.

➢

Remove the batteries and store them in a cool, dry place if you won’t be using the

remote control for a long time. The remote control can be used up to about 23 feet

from the TV. (Assuming typical TV usage, the batteries last for about one year.)

➢

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

ANT IN

UHF

VHF

ANT IN

UHF

VHF

BN68-01532B-Eng.indb 9 2008-05-30 오후 2:31:52

English - 10

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1

Plug the incoming cable into the ANT IN terminal on the back of the TV.

➢

Because this TV is cable-ready, you do not need a cable box to view

unscrambled cable channels.

1

Find the cable that is connected to the ANT OUT terminal on your cable box.

➢

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

2 Connect the other end of this cable to the ANT IN terminal on the back of the TV.

Connecting to a Cable Box that Descrambles All Channels

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below.

You will need a two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available

at most electronics stores.)

1

Find and disconnect the cable that is

connected to the ANT IN terminal on your

cable box.

➢

This terminal might be labeled “ANT

IN”, “VHF IN” or simply, “IN”.

2 Connect this cable to a two-way splitter.

3 Connect an Antenna cable between an

OUTPUT terminal on the splitter and the IN

terminal on the cable box.

4

Connect an Antenna cable between the

ANT OUT terminal on the cable box and the

B–IN terminal on the RF(A/B) switch.

5

Connect another cable between the other

OUT terminal on the splitter and the A–IN

terminal on the RF (A/B) switch.

6

Connect the last Antenna cable between

the OUT terminal on the RF (A/B) switch

and the ANT IN terminal on the rear of the

TV.

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B”

position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s

output channel, which is usually channel 3 or 4.)

ANT OUT

ANT IN

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

Splitter

Incoming

cable

Splitter

Cable Box

Incoming

cable

Splitter

Incoming

cable

TV Rear

RF (A/B)

Switch

ANT IN

Splitter

Incoming

cable

RF (A/B)

Switch

Cable Box

BN68-01532B-Eng.indb 10 2008-05-30 오후 2:31:53

English - 11

Connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output jack on the external device.

1 Connect a HDMI/DVI Cable

or DVI-HDMI Adapter

between the HDMI IN 2 jack

on the TV and the DVI jack

on the DVD Player or Cable

Box/Satellite receiver (Set-

Top Box).

2 Connect Audio Cables

between the DVI IN (HDMI 2)

[R-AUDIO-L] jack on the TV

and the DVD Player or Cable

Box / Satellite receiver (Set-

Top Box).

➢

Each DVD Player or Cable Box / Satellite receiver (Set-Top Box) has a different

back panel configuration.

➢

When connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box),

match the color of the connection terminal to the cable.

➢

When using an HDMI / DVI cable connection, you must use the HDMI IN 2 jack.

Connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output jack on the external device. This connection will

provide the highest quality picture.

1 Connect an HDMI Cable

between the HDMI IN (1, 2, 3

or 4) jack on the TV and the

HDMI jack on the DVD Player

or Cable Box / Satellite

receiver (Set-Top Box).

What is HDMI?

• HDMI, or high-definition multimedia interface, is an interface that enables the

transmission of digital audio and video signals using a single cable.

• The difference between HDMI and DVI is that the HDMI device is smaller in size and

has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed.

➢

Each DVD Player or Cable Box / Satellite receiver (Set-Top Box) has a different

back panel configuration.

➢

The TV may not output sound and pictures may be displayed with abnormal color

when DVD Player or Cable Box / Satellite receivers supporting HDMI versions

older than 1.3 are connected. When connecting an older HDMI cable and there

is no sound, connect the HDMI cable to the HDMI IN 2 jack and the audio cables

to the DVI IN (HDMI2) [R-AUDIO-L] jacks on the back of the TV. If this happens,

contact the company that provided the DVD Player or Cable Box / Satellite receiver

to confirm the HDMI version, then request an upgrade.

➢

HDMI cables that are not 1.3 may cause annoying flicker or no screen display.

HDMI Cable (Not supplied)1

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

TV Rear Panel TV Side Panel

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

TV Rear Panel

Audio Cable (Not supplied)2

HDMI/DVI Cable (Not supplied)1

or

BN68-01532B-Eng.indb 11 2008-05-30 오후 2:31:56

English - 12

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV.

They allow you to view the camcorder tapes without using a VCR.

1 Connect a Video Cable

(or S-Video Cable) between

the AV IN 2 [VIDEO]

(or S-VIDEO) jack on the TV

and the VIDEO OUT jack on

the Camcorder.

2 Connect Audio Cables

between the AV IN 2

[L-AUDIO-R] jacks on the TV

and the AUDIO OUT jacks on

the Camcorder.

➢

Each Camcorder has a different back panel configuration.

➢

When connecting a Camcorder, match the color of the connection terminal to the cable

.

Camcorder

TV Side Panel

S-Video Cable(Not supplied)

1

Video Cable (Not supplied)1

Audio Cable (Not supplied)2

or

Connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD Player/Cable Box/Satellite receiver (Set-Top Box)

to your TV.

1 Connect a Component Cable

between the COMPONENT

IN (1 or 2) [Y, PB, PR]

jacks on the TV and the

COMPONENT [Y, PB, PR]

jacks on the DVD Player

or Cable Box / Satellite

receiver(Set-Top Box).

2 Connect Audio Cables

between the COMPONENT

IN (1 or 2) [R-AUDIO-L] jacks

on the TV and the AUDIO

OUT jacks on the DVD Player

or Cable Box / Satellite

receiver (Set-Top Box).

➢

Component video separates the video into Y (Luminance (brightness)), PB (Blue)

and PR (Red) for enhanced video quality. Be sure to match the component video

and audio connections. For example, if connecting a Component video cable to

COMPONENT IN 1, connect the audio cable to COMPONENT IN 1 also.

➢

Each DVD Player or Cable Box / Satellite receiver (Set-Top Box) has a different

back panel configuration.

➢

When connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box),

match the color of the connection terminal to the cable.

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

TV Rear Panel

Audio Cable (Not supplied)2

Component Cable (Not supplied)1

BN68-01532B-Eng.indb 12 2008-05-30 오후 2:31:57

English - 13

Connecting a VCR

Video Connection

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according

to the instructions on pages 9~10). Skip step 1 if you have not yet connected to an antenna or a cable system.

➢

If you have a “mono” (non-stereo) VCR, use a Y-connector (not supplied) to

connect to the right and left audio input jacks of the TV. Alternatively, connect the

cable to the “R” jack.

If your VCR is stereo, you must connect two cables.

➢

Each VCR has a different back panel configuration.

➢

When connecting a VCR, match the color of the connection terminal to the cable.

➢

When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does

not match the color of the video cable (Yellow).

VCR Rear Panel

TV Rear Panel

2

Audio Cable(Not supplied)

5

Video Cable(Not supplied)4

Antenna cable(Not supplied)

3

S-Video Connection

Your Samsung TV can be connected to an S-Video jack on a VCR.

(This connection delivers a better picture as compared to a standard VCR.)

1 To begin, follow steps 1–3

in the previous section to

connect the antenna or cable

to your VCR and your TV.

2 Connect an S-Video Cable

between the S-VIDEO OUT

jack on the VCR and the AV

IN 2 [S-VIDEO] jack on the

TV.

3 Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the AV

IN 2 [R-AUDIO-L] jacks on

the TV.

An S-Video cable may be included with your VCR. (If not, check your local electronics

store.)

➢

Each VCR has a different back panel configuration.

➢

When connecting a VCR, match the color of the connection terminal to the cable.

VCR Rear Panel

TV Rear Panel

Audio Cable (Not supplied)

3

S-Video Cable(Not supplied)2

Antenna cable(Not supplied)1

1 Unplug the cable or antenna

from the back of the TV.

2 Connect the cable or antenna

to the ANT IN terminal on the

back of the VCR.

3 Connect an Antenna Cable

between the ANT OUT

terminal on the VCR and the

ANT IN terminal on the TV.

4 Connect a Video Cable

between the VIDEO OUT

jack on the VCR and the AV

IN 1 [Y/VIDEO] or AV IN 2

[VIDEO] jack on the TV.

5 Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the AV

IN 1 (or AV IN 2) [R-AUDIO-L]

jacks on the TV.

TV Side Panel

BN68-01532B-Eng.indb 13 2008-05-30 오후 2:32:00

English - 14

Connecting an Amplifier / DVD Home Theater

1 Connect Audio Cables

between the AUDIO OUT

[R-AUDIO-L] jacks on the TV

and AUDIO IN [L-AUDIO-R]

jacks on the Amplifier/DVD

Home Theater.

When an audio amplifier is

connected to the AUDIO OUT

[R-AUDIO-L] jacks terminals :

Decrease the volume of the

TV, and adjust the volume

level with the Amplifier’s

volume control.

➢

Each Amplifier / DVD Home Theater has a different back panel configuration.

➢

When connecting an Amplifier / DVD Home Theater, match the color of the

connection terminal to the cable.

Amplifier / DVD Home Theater

TV Rear Panel

Audio Cable (Not supplied)

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System(Home theater/Receiver) to your

TV.

1 Connect an Optical Cable

between the DIGITAL AUDIO

OUT (OPTICAL) jacks on

the TV and the Digital Audio

Input (OPTICAL) jacks on the

Digital Audio System.

When a Digital Audio System

is connected to the “DIGITAL

AUDIO OUT (OPTICAL)”

jack:

Decrease the volume of the

TV, and adjust the volume

level with the system’s

volume control.

What is OPTICAL?

• An optical cable converts an electric signal into an optical light signal, and transmits

it through glass fibers. S/PDIF is a transmission system of digital audio in the form of

a light wave that uses a glass conductor.

➢

5.1CH audio is possible when the TV is connected to an external device

supporting 5.1CH.

➢

Each Digital Audio System has a different back panel configuration.

➢

When the receiver (home theater) is set to On, you can hear sound output from

the TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send

out 5.1 channel sound to the Home theater receiver. When the source is a digital

component such as a DVD and is connected to the TV via HDMI, only 2 channel

sound will be heard from the Home Theater receiver.

If you want to hear 5.1 channel audio, connect the DIGITAL AUDIO OUT

(OPTICAL) jack on the DVD player or Cable/Satellite Box directly to an Amplifier or

Home Theater, not the TV.

Digital Audio System

TV Rear Panel

Optical Cable (Not supplied)

BN68-01532B-Eng.indb 14 2008-05-30 오후 2:32:03

English - 15

Using the D-Sub Cable

1 Connect a D-Sub Cable

between PC IN [PC] jack on

the TV and the PC output

jack on your computer.

2 Connect a PC Audio Cable

between the PC IN [AUDIO]

jack on the TV and the Audio

Out jack of the sound card on

your computer.

Using the HDMI/DVI Cable

1 Connect a HDMI/DVI cable

between the HDMI IN 2 jack

on the TV and the PC output

jack on your computer.

2

Connect a 3.5 mm Stereo plug

to 2RCA cable between the

DVI IN (HDMI2) [R-AUDIO-L]

jack on the TV and the Audio

Out jack of the sound card on

your computer.

➢

Each PC has a different back panel configuration.

➢

When connecting a PC, match the color of the connection terminal to the cable.

➢

When using an HDMI/DVI cable connection, you must use the HDMI IN 2 terminal.

Connecting a PC

PC

TV Rear Panel

PC Audio Cable (Not supplied)2

D-Sub Cable (Not supplied)1

Using the D-Sub Cable

Using the HDMI/DVI Cable

TV Rear Panel

PC

3.5 mm Stereo plug to 2RCA Cable (Not supplied)2

HDMI/DVI Cable (Not supplied)1

BN68-01532B-Eng.indb 15 2008-05-30 오후 2:32:06

English - 16

Operation

Turning the TV On and Off

Press the POWER button on the remote control.

You can also use the POWER button on the TV.

➢

It may take a while when your TV starts.

Plug & Play Feature

The first time you turn on your new TV, choose your basic settings for language, input source and channels, and

time of day using the plug and play feature. The TV will store these settings in memory. Storing the channels in

memory will allow you to scan the stored channels rather than have to enter their digits each time you want to

change channels.

When the TV is initially powered on, basic settings proceed automatically:

1 Press the POWER button on the remote control.

The message

Menu Language, Store Demo, Channels, and Time will be

set. is automatically displayed.

2 Press the ENTER button to enter the language.

Pressthe▲or▼buttontoselectlanguage,thenpressthe

ENTER button.

The message 'Select Home Use’ when installing this TV in your home. is

automatically displayed.

➢

The Screen Saver is activated if there is no remote control key input for

longer than 1 minute while Plug & Play is running.

 ➢

The Screen Saver is activated if there is no operating signal for longer than

15 minutes.

3 Pressthe◄or►buttontoselectStore Demo or Home Use, then press the

ENTER button.

 ➢

We recommend setting the TV to Home mode for the best picture in your

home environment.

 ➢

Store Demo mode is only intended for use in retail environments.

 ➢

If the unit is accidentally set to Store Demo mode and you want to return

to Home Use (Standard) mode: Press the Volume button on the TV.

When the volume OSD is displayed, press and hold the MENU button on

the TV for 5 seconds.

4 Pressthe▲or▼buttontomemorizethechannelsoftheselectedconnection,

then press the ENTER button.

 ➢

Air: Air antenna signal.

Cable: Cable antenna signal.

Auto: Air and Cable antenna signals.

 ➢

In Cable mode, you can select the correct analog signal source among

STD, HRC, and IRCbypressingthe◄or►button,thenpressthe

ENTER button. If you have Digital cable, select the signal source for both

Analog and Digital. Contact your local cable company to identify the type of

cable system that exists in your particular area.

Continued...

Plug & Play

Menu Language, Store Demo, Channels, and Time will

be set.

Enter

OK

Plug & Play

Select Language of the OSD.

MenuLanguage :English ►

Enter

Plug & Play

Select ‘Home Use’ when installing this TV in your

home.

Home Use

Store Demo

EnterMove

Plug & Play

Select Language of the OSD.

Enter

Menu Language : English

Move

English

Español

Français

SkipEnter

Plug & Play

Select the Antenna source to memorize.

Air

Cable

Auto

Start

Move

Start

Plug & Play

Selects the cable system.

Analog

Digital

HRC IRC

SkipEnter

STD

Move

Start

STD

BN68-01532B-Eng.indb 16 2008-05-30 오후 2:32:07

English - 17

5 The TV will begin memorizing all of the available channels.

After all the available channels are stored, the TV starts to remove scrambled

channels (see page 47). The Auto program menu then reappears.

Press the

ENTER button when channel memorization is complete.

The

Clock Mode menu is displayed.

 ➢

Tostopthesearchbeforeithasnished,presstheENTER button with

stop selected.

6

Press the ENTER button.

Pressthe▲or▼buttontoselect

Manual for setting the current time

manually, then press the ENTER button.

The message

Set current date and time. is displayed.

 ➢

If you select Auto, Set to daylight saving time. is displayed, then go to

step 9.

7 Pressthe◄or►buttontomovetoMonth, Day, Year, Hour, Minute, or

am/pm.

Setthedateandtimeyouwantbypressingthe▲or▼button,thenpressthe

ENTER button.

 ➢

You can set the month, day, year, hour, and minute directly by pressing the

number buttons on the remote control.

8 The message Enjoy your watching. is displayed.

 Whenyouhavenished,pressthe

ENTER button.

 ➢

Even if the ENTER button is not pressed, the message will automatically

disappear after several seconds.

Setting the Clock Automatically

9 Press the ENTER button.

 Pressthe▲or▼buttontoselect

Off or On, then the ENTER button.

The message

Select the time zone in which you live. is displayed.

10 Pressthe▲or▼buttontohighlightthetimezoneforyourlocalarea(and

to move the highlight to the appropriate time zone on the map of the United

States).

Press the ENTER button.

If clock is not automatically set, see page 53 to set the clock.

11 The message Enjoy your watching. is displayed.

 Whenyouhavenished,pressthe

ENTER button.

 ➢

Even if the ENTER button is not pressed, the message will automatically

disappear after several seconds.

Continued...

Plug & Play

Auto Program is completed.

56 channels are memorized.

DTV Air : 20 Air : 11

DTV Cable : 15 Cable : 10

OK

Enter Skip

Plug & Play

Auto Program in Progress.

Stop

Enter Skip

Air

3%

DTV Air : -- Air : --

DTV Cable : -- Cable : --

OK

Plug & Play

Enjoy your watching.

Plug & Play

Set current date and time

01

Month

01

Day

2008

Year

12

Hour

00

Minute

am

am/pm

SkipEnterAdjustMove

OK

Plug & Play

Enjoy your watching.

Plug & Play

Select the time zone in which you live.

Newfoundland

Atlantic

Eastern

Central

Mountain

Pacific

▼

SkipEnter

Move

Plug & Play

Set the Clock Mode.

Clock Mode : Auto

Auto

Manual

EnterMove

Skip

Plug & Play

Set to daylight saving time.

DST : Off

Off

On

EnterMove

Skip

Plug & Play

Stop

Enter Skip

Removing scrambled channel.

DTV Cable 41

77%

DTV Air : 05 Air : 12

DTV Cable : 25 Cable : 32

BN68-01532B-Eng.indb 17 2008-05-30 오후 2:32:08

English - 18

If you want to reset this feature...

1 Press the MENU button to display the menu.

Pressthe▲or▼buttontoselect

Setup, then press the ENTER button.

2 Press the ENTER button to select Plug & Play. For further details on setting

up options, refer to the pages 16~17.

 ➢

The Plug & Play feature is only available in the TV mode.

Changing Channels

Using the Channel Buttons

1 Press the CH

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

or CH

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

button to change channels.

➢

When you press the CH

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

or CH

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

button, the TV changes channels in

sequence. You will see all the channels that the TV has memorized.

(The TV must have memorized at least three channels). You will not

see channels that were either erased or not memorized. See page 20 to

memorize channels.

➢

To increase the channel number, turn the wheel clockwise when the Channel

Display is displayed. To decrease the channel number, turn the wheel

counterclockwise.

Using the Number Buttons

1

Press the number buttons to go directly to a channel. For example, to select

channel 27, press 2, then 7.

The TV will change channels when you press the second number.

➢

For quick channel change, press the number buttons, then press the ENTER

button.

➢

You can press number buttons on Remote control for direct channel access,

press the same Number button again to switch between digital and analog

TV channels broadcast by the same station.

Using the “-” Button

The “

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

” button is used to select stations that broadcast a digital signal.

1

For example, for Channel 7-1, press 7, then

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

, then 1.

➢

HD indicates the TV is receiving a Digital High Definition signal.

SD indicates the TV is receiving a Standard Definition signal.

➢

For quick channel change, press the number buttons, then press the ENTER

button.

Using the PRE-CH Button to select the Previous Channel

Use the number buttons to quickly tune to any channel.

1

Press the PRE-CH button. The TV will switch to the last channel viewed.

➢

To quickly switch between two channels that are far apart, tune to one

channel, then use the number button to select the second channel.

Then use the PRE-CH button to quickly alternate between them.

Plug & Play ►

Language : English

Time

Network Setup

V-Chip

Caption

External Settings

Entertainment : Off

Setup

Plug & Play

Menu Language, Store Demo, Channels, and Time

will be set.

Enter

OK

Return

BN68-01532B-Eng.indb 18 2008-05-30 오후 2:32:09

English - 19

Adjusting the Volume

Using the Volume Buttons

1 Press the VOL

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

or VOL

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

button to increase or decrease the volume.

➢

To turn the volume up, turn the wheel clockwise when the Volume

Control window is displayed. To turn the volume down, turn the wheel

counterclockwise.

Using the Mute Button

At any time, you can cut off the sound using the MUTE button.

1

Press MUTE and the sound cuts off.

Mute will displayed on the screen.

2 To turn mute off, press the MUTE button again, or simply press the VOL

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

or

VOL

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

button.

Viewing the Menus

1 With the power on, press the MENU button.

The main menu appears on the screen. The menu’s left side has icons:

Picture, Sound, Channel, Setup, Input, Application.

2 Pressthe▲or▼buttontoselectoneoftheicons.

Then press the ENTER button to access the icon’s sub-menu.

➢

To move to a lower menu, turn the wheel clockwise when the menu Display is on

the screen. To move to a higher menu, turn the wheel counterclockwise.

3 Press the EXIT button to exit.

➢

It takes about one minute until the on-screen menu disappears.

Mode : Standard

Cell Light : 7

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Detailed Settings

Picture

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

1 Press the INFO button on the remote control.

The TV will display the channel, the type of sound, and the status of certain

picture and sound settings.

Press the INFO button once more or wait approximately 10 seconds and it disappears

automatically.

TV #1

Sun, Sep 3 1:45 pm

M. Spillane’s Mike Hammer

Bonocrunch

DTV Air

13-1

Dolby Digital

480i 4:3 English

12:59 pm - 1:59 pm

BN68-01532B-Eng.indb 19 2008-05-30 오후 2:32:10

English - 20

Memorizing the Channels

Your TV can memorize and store all of the available channels for both air and cable channels. After the available

channels are memorized, use the CH

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

or CH

RETURN

TOOLS

INFO

W.LINK

CH LIST

EXIT

button to scan through the channels. This eliminates the need

to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a

broadcast source, memorizing the channels (automatic) and adding and deleting channels (Channel Lists).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must

specify the type of signal source that is connected to the TV (i.e. an Air or a Cable

system).

1

Press the MENU button to display the menu.

Pressthe▲or▼buttontoselect

Channel, then press the ENTER button.

2 Press the ENTER button to select Antenna.

Pressthe▲or▼buttontoselect

Air or Cable, then press the ENTER button.

Press the EXIT button to exit.

Continued...

Using the Remote Control Backlight Buttons

Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.

1 1. Press the ON/OFF light button

➢

Pressing the ON/OFF light button toggles between ON and OFF.

➢

When ON, the button backlight is turned on for a moment.

➢

Pressing a remote control button when the remote control is on turns the button backlight on for a moment. If

you touch or move the remote control and the motion is detected by the sensor of the remote control, the button

backlight will be turned on for a moment.

➢

The remote contains two small movement sensors that control the backlight function. If you shake or drop the

remote, you may hear the sensors rattle. This is normal and is not a defect.

➢

The button backlight will not be turned on when the remote control is turned off.

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The TOOLS menu

changes depending on which external input mode you are viewing.

1 Press the TOOLS button.

The

TOOLS menu will appear.

2 Pressthe▲/▼buttontoselectamenu,thenpresstheENTER button.

3 Pressthe▲/▼/◄/►/ENTER buttons to display, change, or use the selected

items. For a more detailed description of each function, refer to the correspond-

ing page.

Antenna

:

Air

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Air

Cable

ChannelChannel

Antenna

:

Air ►

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Signal Strength

Device List

Multi-Track Sound : Stereo

Picture Mode : Standard

Sound Mode : Custom

Sleep Timer : Off

Add to Favorite

Switch to Cable

Tools

Move Enter Exit

●DeviceList,seepage102

●Multi-TrackSound,seepage38

●PictureMode,seepage23

●SoundMode,seepage36

●SleepTimer,seepage55

●AddtoFavorite,seepage43

●SwitchtoCable(orSwitchtoAir),seepages20~21

●PIP:seepages34~35

●Autoadjustment:seepage50

BN68-01532B-Eng.indb 20 2008-05-30 오후 2:32:10

La page charge ...

Samsung 650 Manuel utilisateur

Ce manuel convient également à

Samsung 650 Manuel utilisateur

dans d''autres langues

Documents connexes