Bosch HBL35 Guide d'installation

Marque: Bosch

Modèle: HBL35

Catégorie: Micro-ondes

Taper: Guide d'installation

Built=in Ovens

Models: HBL33, HBN33, HBL34, HBN34, HBL35, HBN35, HBL54, HBN54,

HBL58, HBN56, HBL57, HBL8550, HBL8850, HBL8750

Table of Contents

Safety ...................................... 1

ImportantSafety Instructions ....................................... 1

Preparation .................................. 3

Before you Begin ................................................. 3

Tools and Parts Needed ...................................................... 3

Parts Included .............................................................. 3

27" Appliances .................................................. 3

General Information .......................................................... 3

30" Appliances .................................................. 6

Removing Packaging ............................................. 9

For Convection Microwave Combination Units ..................................... 9

Preparing Oven ............................................................. 9

Installation ................................. 10

ElectricalInstallation ............................................. 10

Oven Installation ................................................ 12

Testing Operation ............................................... 13

Service .................................... 14

Before Calling Service ....................................................... 14

This Bosch Appliance is made by

BSH Home Appliances Corporation

5551 McFadden Ave.

Huntington Beach, CA 92649

Questions?

1-800-944-2904

www.boschappliances.com

We look forward to hearing from you!

Safety

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

Appliance Handling Safety

Safety Codes and Standards

Electric Safety

WARNING:

If the information in this manual is not followed exactly, fire or shock may result

causing property damage or personal injury.

WARNING:

Do not repair or replace any part of the appliance unless specifically recommended

in the manuals. Improper installation, service or maintenance can cause injury or

property damage. Refer to this manual for guidance. All other servicing should be

done by a qualified technician.

Do not lift appliance by door handle. Remove the door for easier handling and

installation. See instructions in Use and Care Manual.

Unit is heavy and requires at least two people or proper equipment to move.

Hidden surfaces may have sharp edges. Use caution when reaching behind or

under appliance.

This appliance complies with one or more of the following Standards:

• UL 858, The Standard for the Safety of Household Electric Ranges

• UL 923, The Standard for the Safety of Microwave Cooking Appliances

• UL 507, The Standard for the Safety of Electric Fans

• ANSI Z21.1, The American National Standard for Household Cooking Gas

Appliances

• CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

• CAN/CSA-C22.2 No. 61-M89 Household Cooking Ranges

It is the responsibility of the owner and the installer to determine if additional

requirements and/or standards apply to specific installations.

Before you plug in an electrical cord, be sure all controls are in the OFF position.

If required by the National Electrical Code (or Canadian Electrical Code), this

appliance must be installed on a separate branch circuit.

Installer - show the owner the location of the circuit breaker or fuse. Mark it for easy

reference.

Important - Save these instructions for the local electrical inspector's use.

Before installing, turn power OFF at the service panel. Lock service panel to prevent

power from being turned ON accidentally.

Refer to data plate for more information. See "Data Plate" under "Service" for data

plate location.

English 1

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

Related Equipment Safety

Transport

Be sure your appliance is properly installed and grounded by a qualified technician.

Installation, electrical connections and grounding must comply with all applicable

codes.

Remove all tape and packaging before using the appliance. Destroy the packaging

after unpacking the appliance. Never allow children to play with packaging material.

Never modify or alter the construction of the appliance. For example, do not remove

leveling legs, panels, wire covers or anti-tip brackets/screws.

To avoid damage to the oven vent, use the transport method shown in the picture

below.

English 2

Preparation

Before you Begin

Tools and Parts Needed

Parts Included

• Phillips head screwdriver

• Measuring tape

• Drill with bit (1/8")

Phillips head screws (6)

27" Appliances

General Information

Power Requirements The outlet must be properly grounded in accordance with all applicable codes.

Dimensions for 27" Wall-Mounted Units

24"

(610ram)

2413/16" (718mm)

(630rnm) .-_

27"

(686rnrn)

237/8" (606ram)

22" (559mm)

251/2"

rain. 43/4"(121 ram)

rnaxi31L__3/8"(797mm)

Single Oven 27"

It is good practice, when oven is

installed at the end of a cabinet run,

adjacent to a perpendicular wall or

cabinet door, to allow at least 1/4"

space between the side of the oven and

the wall/door.

For oven support, install 2x4's

extending front to back flush with the

bottom and the side of the opening. The

supporting base must be well secured

to the floor/cabinet and level.

Note: The conduit box must be installed

either above or below the unit. If the

conduit box is installed below the unit, a

2" diameter hole or space is required

between the back wall and the right rear

of the 2x4 supports.

The cabinet base must be flat and

capable of supporting a weight of at

least 210 Ibs (95 kg).

English 3

263/4"

(680turn)

49314"

(1264mm)

237/8"(606turn)

22" (559rnrn)

93/4"

(248turn)

Double Oven 27"

It is good practice, when oven is

installed at the end of a cabinet run,

adjacent to a perpendicular wall or

cabinet door, to allow at least 114"

space between the side of the oven

and the wall/door.

For oven support, install 2x4's

extending front to back flush with the

bottom and the side of the opening.

The supporting base must be well

secured to the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 355 Ibs (161 kg).

263/4"

(680turn)

2413/16"

(630ram)

22" (559mm)

483/8"

(1229rnrn)

(606turn)

491/2"

(1257mm)

Combo Oven with Microwave 27"

It is good practice, when oven is

installed at the end of a cabinet run,

adjacent to a perpendicular wall or

cabinet door, to allow at least 114"

space between the side of the oven

and the wall/door.

For oven support, install 2x4's

extending front to back flush with the

bottom and the side of the opening.

The supporting base must be well

secured to the floor/cabinet and level.

Note: The conduit box must be

located above the unit to facilitate

connecting and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 330 Ibs (150 kg).

English 4

263/4"

(680ram)

60314"

(1543turn)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Combo Oven with Microwave and

Warming Drawer 27"

It is good practice, when oven is

installed at the end of a cabinet run,

adjacent to a perpendicular wall or

cabinet door, to allow at least 114"

space between the side of the oven

and the wall/door.

For oven support, install 2x4's

extending front to back flush with the

bottom and the side of the opening.

The supporting base must be well

secured to the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 370 Ibs (168 kg).

.._ 237/8" (606rnm)

(559rnrn)

27" Under-the-counter units

24"

(610ram)

281/4"

(718mm)

36"

(915mm)

263/4"

2413/16"

(630ram)

43/4"

(121mm)

English 5

30" Appliances

Dimensions for 30" Wall-Mounted Units

2713/16"

(706ram)

24"

(610ram)

(718mm)

27"

(686ram)

237/8" (606rara)

22" (559mm)

rain. 43/4" (121ram)

max. 313/8"(7971

Single Oven 30"

It is good practice, when oven is installed

at the end of a cabinet run, adjacent to a

perpendicular wall or cabinet door, to

allow at least 1/4" space between the

side of the oven and the wall/door.

For oven support, install 2x4's extending

front to back flush with the bottom and

the side of the opening. The supporting

base must be well secured to the floor/

cabinet and level.

Note: The conduit box must be installed

either above or below the unit. If the

conduit box is installed below the unit, a

2" diameter hole or space is required

between the back wall and the right rear

of the 2x4 supports.

The cabinet base must be flat and

capable of supporting a weight of at

least 190 Ibs (86 kg).

293/4"

(755rara)

2713/16"

(706ram)

513/4"

(1314tara)

493/4"

(1264rara)

237/8" (606rara)

L¢ 22" (559rara)

511/8"

(1299ram)

93/4"

(248rara)

Double Oven 30"

It is good practice, when oven is

installed at the end of a cabinet run,

adjacent to a perpendicular wall or

cabinet door, to allow at least 1/4"

space between the side of the oven

and the wall/door.

For oven support, install 2x4's

extending front to back flush with the

bottom and the side of the opening.

The supporting base must be well

secured to the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 330 Ibs (150 kg).

English 6

2713/16"

(706ram)

50"

(1270mm)

483/8"

(1229mm)

22" (559mm)

(606ram)

491/2"

(1257mm)

191/2"

(500ram)

24"

(610ram) _ql

293/4"

(755mm)

2713/16"

(706ram)

613/8"

(1559rnm

595/8"

(1514mm)

93/4"

(248mm)

._ 237/8" (606rnm)

(559rnm)

Combo Oven with Microwave 30"

It is good practice, when oven is

installed at the end of a cabinet run,

adjacent to a perpendicular wall or

cabinet door, to allow at least 114"

space between the side of the oven

and the wall/door.

For oven support, install 2x4's

extending front to back flush with the

bottom and the side of the opening.

The supporting base must be well

secured to the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 290 Ibs (132 kg).

Combo Oven with Microwave and

Warming Drawer 30"

It is good practice, when oven is

installed at the end of a cabinet run,

adjacent to a perpendicular wall or

cabinet door, to allow at least 114"

space between the side of the oven

and the wall/door.

For oven support, install 2x4's

extending front to back flush with the

bottom and the side of the opening.

The supporting base must be well

secured to the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 310 Ibs (141 kg).

English 7

293/4"

(755mm)

281/2"

(610mm) _

2713/16"

Rm)

40" iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

(1016mm)

381/8"

(968mm)

93/4"

(248mm)

Combo Oven with Warming

Drawer 30"

It is good practice, when oven is

installed at the end of a cabinet run,

adjacent to a perpendicular wall or

cabinet door, to allow at least 114"

space between the side of the oven

and the wall/door.

For oven support, install 2x4's

extending front to back flush with the

bottom and the side of the opening.

The supporting base must be well

secured to the floor/cabinet and level.

Note: The conduit box must be located

above the unit to facilitate connecting

and servicing.

The cabinet base must be flat and

capable of supporting a weight of at

least 290 Ibs (132 kg).

_ 237/8" (606rnrn)

22" (559rnrn)

30" Under-the-counter-Units

24"

(610ram)

161/2"

293/4"

281/4"

(718mm)

2713/16"

281/2"

43/4"

(121mm)

English 8

Removing Packaging

• Cut straps on outside of box.

• Remove cardboard box.

• Remove all top and side cardboard and Styrofoam braces.

• Place oven in front of cabinets where it is to be installed.

• Unscrew unit from Left and Right Brackets as show in "Left and Right

Packaging Bracket Removal."

Left and Right Packaging Bracket Removal

Note:

For Convection

Microwave Combination

Units

Different models use different packaging materials. Actual brackets may look

differently. Bracket remains in packaging base. Unit should stay on packaging base

until ready to be lifted into cabinet cutout.

Remove 2 rear support Convection Microwave Shipping Brackets prior to

installation as shown in "Convection Microwave Shipping Bracket Removal."

Convection Microwave Shipping Bracket Removal (for Convection Microwave Combination Units Only)

Preparing Oven

Place oven in front of cabinets where it is to be installed. Rest it on a jack or other

sturdy support so that it is in line with the cabinet cutout.

English 9

Installation

Electrical Installation

All model ovens on the front cover are dual rated, designed to be connected to

either 208/240V AC, 60 Hz, 4 wire, single-phase power supply.

Model Circuit Required

208V, 60 Hz 240V, 60 Hz

HBN33, HBL33 25 AMP 30 AMP

HBN34, HBL34, 30 AMP 30 AMP

HBN54, HBL54

HBL85

HBN35, HBL35, 40 or 50 Amp circuit. Refer to local electrical codes

HBN56, HBL56, HBL57, for de-rating requirements.

HBL8650, HBL8750

The electrical supply should be a 4-wire single-phase AC. Install a suitable conduit

box (not furnished). An appropriately-sized, UL-listed conduit connector must be

used to correctly attach the conduit to the junction box.

Important: Local Codes may vary; installation, electrical connections and

grounding must comply with all applicable local codes.

If local codes permit grounding through the electrical supply neutral, connect both

the white neutral wire and the bare ground wire from the oven to the white neutral

electrical supply wire.

English 10

Electrical Connection

The four-wire connection is preferred, but where local codes permit, the three wire

connection is also acceptable.

Four-wire Connection

Junction box Cable from

_'-.. power supply

White wires

Red wires

Ungrounded Neutral

/ _- Black wires

Bare or green w_res Cable _-.

from oven U,L,-listed conduit connector

Connect the red oven wire to the red electrical supply wire (hot wire).

Connect the black oven wire to the black electrical supply wire (hot wire).

Connect the white neutral oven wire to the white neutral (not bare ground)

electrical supply wire.

Connect the bare ground oven wire to the bare ground electrical supply wire.

Three-wire Connection

Junction box. Cable from

._er s_pply

Red wires_ _ Grounded Neutral

White wires

___ __:wire

or green _ . .- innectorres

Bare

from oven

• Connect red wire from oven to red wire injunction box.

• Connect black wire from oven to black wire in junction box.

• Connect both green ground wire and white wire from oven to white (or gray)

neutral wire in junction box.

The conduit cable, where connected at the oven, swivels. Rotate conduit cable

upward (or downward) and direct through hole prepared in cabinet to attach to J-

Box.

To maintain serviceability, the flex conduit must not be shortened and should be

routed to permit temporary removal of the oven.

English 11

Oven Installation

Note: Before installing the oven, be sure to verify the cabinet dimensions and electrical

connections.

Removing the Oven Door For ease of installation, some oven doors may be removed to reduce the weight of

the oven by 30 Ibs (14 kg) per door, before installing into the cabinet. See "To

remove the oven door."

CAUTION:

When removing the door:

Make sure oven is cool and power to the oven has been turned

off before removing the door. Failure to do so could result in

electrical shock or burns.

• The oven door is heavy and fragile. Use both hands to remove

the oven door. The door front is glass. Handle carefully to avoid

breaking.

• Grasp only the sides of the oven door. Do not grasp the handle

as it may swing in your hand and cause damage or injury.

• Failure to grasp the oven door firmly and properly could result in

personal injury or product damage.

• To avoid injury from hinge bracket snapping closed, be sure that

both levers are securely in place before removing the door. Also,

do not force door open or closed - the hinge could be damaged

and injury could result.

To remove the oven door:

Be sure to read the above CAUTION

before attempting to remove the door.

Open the door completely.

Flip levers on hinges toward you.

Close door carefully until it stops. It will

be about half way closed.

Holding the door firmly on both sides

using both hands, pull the door up and

out of the hinge slots. Hold firmly; the

door is heavy.

Place the door in a convenient and

stable location for cleaning.

English 12

Installing the Oven 1. Lift or slide unit into cabinet cutout. Do not lift appliance by door handle.

2. Push straight in until oven trim is flush with cabinet wall, being careful not to

crimp flexible conduit between oven and cabinet back wall. The oven should be

straight and level, not crooked.

3. Install supplied screws through tap holes in trim. (2 screws for single ovens, 4

screws for double/combo ovens)

To replace the oven door:

Holding the door firmly in both hands,

place hinges in hinge slots.

Open door all the way to expose

hinges and slots.

Push lever down and away from you

until flush with the bracket.

Close and open door slowly to be sure

it is correctly and securely in place.

Door must be straight, not crooked.

Testing Operation

1. Turn on power at the breaker.

2. Check power at junction box using a volt meter.

For 240 V installation, the reading between the red and black wires (line to line)

should be 220 to 240 volts.

For 208 V installation, the reading between the red and black wires (line to line)

should be 190 to 208 volts.

3. Test the oven mode.

Select the BAKE mode. See the Use and Care Manual for detailed operation

instructions.

4. Verify that the oven light comes on and the oven begins to preheat.

5. Test the door lock.

Set the SELF CLEAN mode. Confirm that the door locks when the lock icon

appears in the display.

6. If installing a double oven, test the second oven as well.

7. If any of the tests do not result as explained above, contact Bosch service for

assistance. Otherwise, the installation is complete at this time.

English 13

Service

Before Calling Service

Data Plate

See Use and Care Manual for troubleshooting information. Refer to the Warranty in

the Use and Care Manual.

To reach a service representative, see the contact information at the front of the

manual. Please be prepared with the information printed on your product data plate

when calling.

The data plate shows the model and serial number. Refer to the data plate on the

appliance when requesting service. The data plate is located on the underside of

the control panel:

Data Plate

English 14

Table des mati res

Sdcuritd ..................................... 1

Consignes de securit6 importantes ................................... 1

Prdparation .................................. 3

Avant de commencer ............................................. 3

Outils et pieces necessaires ................................................... 3

Pieces incluses ............................................................. 3

Appareils electrom6nagers de 27 po ................................. 3

Informations generales ....................................................... 3

Appareils electrom6nagers de 30 po ................................. 6

Pour enlever I'emballage ........................................... 9

Pour les fours combines de micro-ondes et convection .............................. 9

Installation ................................. 10

Installation electrique ............................................ 10

Raccordement electrique ..................................................... 11

Installation du four ............................................... 12

Test de contr61e ................................................ 13

Ddpannage ................................. 14

Avant d'appeler le service de depannage ........................................ 14

Cet appareil electromenager de Bosch est fait par

BSH Home Appliances Corporation

5551 McFadden Ave.

Huntington Beach, CA 92649

Questions ?

1-800-944-2904

www.boschappliances.com

Nous attendons de vos nouvelles !

S6curitd

Consignes de sdcuritd importantes

LIRE ET CONSERVER CES CONSIGNES

Securit6 de manipulation de

I'appareil

Codes et normes de securite

Securite electrique

AVERTISSEMENT:

si les informations de ce manuel ne sont pas suivies _ la lettre, un incendie ou un

choc 61ectrique peuvent se produire et sont susceptibles de causer des dommages

mat6riels ou des 16sions corporelles.

AVERTISSEMENT:

ne pas r6parer ni remplacer des pi_ces de I'appareil _ moins que cela ne soit

express6ment recommand6 dans le manuel. Toute installation, r6paration ou

maintenance inad6quate peut entrafner des blessures ou des dommages mat6riels.

Consulter ce manuel pour obtenir des conseils sur la fa(_on de proc6der. Tousles

travaux d'entretien doivent 6tre confi6s _ un technicien qualifi6.

Ne pas soulever I'appareil par la poign6e de la porte. Enlever la porte pour faciliter

la manipulation et I'installation de I'appareil. Voir les instructions du Manuel

d'utilisation et d'entretien.

Cet appareil est Iourd et il faut au moins deux personnes ou 1'6quipement appropri6

pour le d6placer.

Les surfaces cach6es peuvent comporter des ar_tes vives. Faites attention en

6tendant le bras derriere I'appareil ou en dessous.

Cet appareil est conforme _ une ou plusieurs des normes suivantes :

• UL 858, Norme pour la s6curit6 des cuisini_res 61ectriques domestiques

• UL 923, Norme pour la s6curit6 des appareils de cuisson _ micro-ondes

• UL 507, Norme pour la s6curit6 des ventilateurs 61ectriques

• ANSI Z21.1, Norme nationale am6ricaine pour les appareils de cuisson _ gaz

domestiques

• CAN/CSA-C22.2 No. 113-M1984, Ventilateurs et soufflantes

• CAN/CSA-C22.2 No. 61-M89, Cuisini_res pour usage m6nager

II incombe au propri6taire et _ I'installateur de d6terminer si des exigences et/ou

normes additionnelles s'appliquent pour des installations sp6cifiques.

Avant de brancher le cordon 61ectrique, v6rifier que toutes les commandes sont

dans la position "OFF" (Arr6t).

S'il y a lieu, conform6ment au Code national de 1'61ectricit6(ou au Code canadien

de 1'61ectricit6), cet appareil doit 6tre install6 sur un circuit de d6rivation s6par6.

Installateur - indiquer au propri6taire I'emplacement du disjoncteur ou du fusible.

Identifier sa position pour pouvoir le retrouver facilement plus tard.

Frangais 1

Consignes de sdcuritd importantes

LIRE ET CONSERVER CES CONSIGNES

Securit6 apparentee concernant

I'equipement

Important - Conserver ces instructions pour I'usage de I'inspecteur local en

61ectricit6.

Avant I'installation, couper le courant au panneau de service. Verrouiller le panneau

de service pour 6viter que le courant ne soit accidentellement r6tabli.

Pour plus d'informations, se reporter _ la plaque signal6tique. Pour connaftre

I'emplacement de la plaque signal6tique, voir "Plaque signal6tique" sous

"Entretien".

S'assurer que I'appareil est ad6quatement install6 et mis _ la terre par un technicien

qualifi6. L'installation, les connexions 61ectriques et la mise _ la terre doivent 6tre

conformes _ tous les codes applicables.

Retirer le ruban adh6sif et I'emballage avant d'utiliser I'appareil. D6truire I'emballage

apr_s avoir d6ball6 I'appareil. Ne jamais laisser les enfants jouer avec les mat@iaux

de conditionnement.

Ne jamais modifier ni alt6rer la configuration de I'appareil. Par exemple, ne pas

retirer les pieds de nivellement, les panneaux, les couvercles de c_blage ou les

fixations/vis antibasculement.

Transport Pour 6viter tout dommage _ 1'6vent du four, utiliser la m6thode de transport illustr6e

ci-dessous.

Frangais 2

Prdparation

Avant de commencer

Outils et pieces

necessaires

Pieces incluses

• Tournevis _ t_te Phillips

• Ruban _ mesurer

• Perceuse avec foret (1/8 po)

Vis cruciformes (6)

Appareils dlectromdnagers de 27 po

Informations gen6rales

Exigences electriques La prise doit 6tre correctement reli6e _ la terre selon tousles codes applicables.

Dimensions pour les appareils muraux de 27 po

I 263/4"

(680mmL_' _ 2413/16"

(630ram)

291/16"

(738mm)

27"

(686mm)

_'- 237/8"(606ram)

22" (559mm)

24"

(610ram)

251/2"

Four unique de 27 po

Lorsque le four est install6 _ I'extr6mit6

d'une s6rie de placards, adjacent _ un

mur perpendiculaire ou _ une porte de

placard, il est recommand6 de laisser

au moins 1/4 po (0,6 cm) d'espace

entre la paroi du four et le mur ou la

porte.

Pour le soutien du four, installer des

montants de 2 pouces sur 4 qui

s'6tendent de I'avant _ I'arri_re et

viennent affleurer le fond et le c6t6 de

I'ouverture. Le socle de soutien doit

6tre bien fix6 au plancher ou au coffret

et _tre de niveau.

Remarque :la bofte de connexions

doit _tre install6e soit au-dessus, soit

au-dessous de I'appareil. Si la bofte de

connexions est install6e sous

I'appareil, un espace ou une ouverture

de 2 po (5,8 cm) de diam_tre est

requis entre lemur arri_re et la partie

arri_re droite des montants de support

de 2 pouces sur 4.

Le socle du coffret doit _tre plate et

apte a soutenir un poids d'au moins

210 Ib (95 kg).

Frangais 3

La page charge ...

Bosch HBL35 Guide d'installation

Marque: Bosch

Modèle: HBL35

Catégorie: Micro-ondes

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Bosch HBL35 Installation guide
español: Bosch HBL35 Guía de instalación

Bosch HBL35 Guide d'installation

Bosch HBL35 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents