LG PRARH1 Guide d'installation

Marque: LG

Modèle: PRARH1

Catégorie: Climatiseurs split-system

Taper: Guide d'installation

www.lg.com

INSTALLATION MANUAL

AIR CONDITIONER

• Please read this installation manual completely before installing the product.

• Installation work must be performed in accordance with the national wiring

standards by authorized personnel only.

• Please retain this installation manual for future reference after reading it

thoroughly.

TYPE : Auxiliary Heater Relay Kit (for Multi V Product)

MODEL : PRARH1

P/NO : MFL65920004

ENGLISH FRANÇAIS

ESPAÑOL

2 Auxiliary Heater Relay Kit

IMPORTANT!

CAUTION

: Improper installation, adjustment, alteration, service or maintenance can void the warranty.

The weight of the condensing unit requires caution and proper handling procedures when lifting

or moving to avoid personal injury. Use care to avoid contact with sharp or pointed edges.

Safety Precautions

• Always wear safety eye wear and work gloves when installing equipment.

• Never assume electrical power is disconnected. Check with meter and equipment.

NOTE TO INSTALLING DEALER: The Owners Instructions and Warranty are to be given to the owner

or prominently displayed near the indoor Furnace/Air Handler Unit.

When wiring:

Electrical shock can cause severe personal injury or death. Only a qualified,

experienced electrician should attempt to wire this system.

• Do not supply power to the unit until all wiring and tubing are completed or reconnected and checked.

• Highly dangerous electrical voltages are used in this system. Carefully refer to the wiring diagram and these

instructions when wiring. Improper connections and inadequate grounding can cause accidental injury or death.

• Ground the unit following local electrical codes.

• Connect all wiring tightly. Loose wiring may cause overheating at connection points and a possible fire hazard.

When installing...

... in a wall: Make sure the wall is strong enough to hold the unit's weight.

It may be necessary to construct a strong wood or metal frame to provide added support.

... in a room: Properly insulate any tubing run inside a room to prevent "sweating" that can cause

dripping and water damage to wall and floors.

When servicing

• Turn the power OFF at the main power box(mains) before opening the unit to check or repair

electrical parts and wiring.

• Clean up the site after you finish, remembering to check that no metal scraps or bits of wiring have

been left inside the unit being serviced.

WARNING

• Installation must adapt with local building codes or with the Nation al Electrical code NFPA 70/ANSI C1-1993

(or current edition ) along with Canadian Electrical Code Part1 CSA C.22.1

• The information contained in the manual is intended for use by a qualified service technician familiar with safety

procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, property

damage, personal injury and/or death.

Please read this instruction sheet completely before installing the product.

This air conditioning system meets strict safety and operating standards. As the installer or service person,

it is an important part of your job to install or service the system so it operates safely and efficiently.

Installation Manual 3

Auxiliary Heater Relay Kit INSTALLATION MANUAL

TABLE OF CONTENTS

1. Safety Precautions ............................................................................................................4

2. Included Items....................................................................................................................5

3. Assembly Diagram ............................................................................................................6

4. Electrical Wiring...............................................................................................................12

5. Installer Setting................................................................................................................13

6. Control map of AUX HEATER.........................................................................................15

7. Troubleshooting Guide ...................................................................................................17

4 Auxiliary Heater Relay Kit

To prevent injury to the user or other people and property damage, the following instructions

must be followed.

n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness

is classified by the following indications.

1. Electric works should be carried out according to ‘The technology requirement on the elec-

tric installation’, The wiring standard and this manual by a qualified personnel.

If the installation is not complete, electric shock or fire may occur, or death or injury can be caused.

3. If the capacity of the power circuit is insufficient or its installation was not done completely,

this may cause electric shock, fire or etc..

4. If the installation was done by a user, there may be incompleteness, which may cause elec-

tric shock, fire, injury and death.

5. When operating the machine (applying power to the machine), do not carry out any electric

work and do not put hand or finger into it. This may cause electric shock, injury and death.

6. Use only UL1996 approved heater.

n Meanings of symbols used in this manual are as shown below.

WARNING

CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage.

Be sure not to do.

Be sure to follow the instruction.

WARNING

1. Before installation, read this manual and carry out the works according to it.

2. Before installation, be sure to check all the included items. (However, be sure to use all

kinds of certified products when purchasing the items other than those provided by LG at

your local store.)

3. Be sure to carry out the earth work. (However, do not connect the unit to gas pipe, water

pipe, a lightning rod and a phone earth line. In addition, if the earth was not completely

done, this may cause electric shock and fire.)

CAUTION

1. Safety Precautions

Safety Precautions

Installation Manual 5

ENGLISH

Item Auxliary Heater Relay Kit Screw Insulation Installation Manual

Q’ty 1 2 2 1

Model

2. Included Items

• PRARH1 applies to High Static Duct, Low Static Duct, 1Way CST, 2Way CST, 4Way CST and Ceiling

Suspended types.

(Unit : inch)

Figure

PRARH1

Included Items

2-19/32

1-13/32

7-9/32

6-23/32

2-19/32

2-7/32

1-7/16

3-13/32

Aux heater

communication lines

6 Auxiliary Heater Relay Kit

Assembly Diagram

Check the distance between PRARH1 and a control box

when connecting anchor bolts.

9/16

Auxiliary Heater communication lines

(under AC24V,over AWG24)

These wires should not make

contact with high voltage lines.

To indoor unit PCB

(CN-PTC)

AB AB

Fig. A

Control box cover

screw

Insulation

3. Assembly Diagram

n High Static Duct

※

Wiring

Note: While connecting the PRARH1, attach insulation at the rear of the control box cover

where it receives screws as shown in Fig. A.

Please clean up the remaining wires after installation.

Step1. Open control box cover. Step2. Assemble PRARH1 with control box cover.

Step3. Open the cover of PRARH1 and connect wires. Step4. Assemble control box cover.

Assembly Diagram - PRARH1

(Unit : inch)

CAUTION

Assembly Diagram

Installation Manual 7

ENGLISH

n Low Static Duct

Check the distance between PRARH1 and the top of model

when connecting anchor bolts.

4 13/32

Auxiliary Heater communication lines

(under AC24V,over AWG24)

These wires should not make

contact with high voltage lines.

To indoor unit PCB

(CN-PTC)

AB AB

※

Wiring

Fig. A

Control box cover

screw

Insulation

Note: While connecting the PRARH1, attach insulation at the rear of the control box cover

where it receives screws as shown in Fig. A.

Please clean up the remaining wires after installation.

Aux heater communication lines

Step1. Open control box cover. Step2. Assemble PRARH1 with control box cover.

Step3. Open the cover of PRARH1 and connect wires. Step4. Assemble control box cover.

(Unit : inch)

CAUTION

8 Auxiliary Heater Relay Kit

n 1 Way CST

Auxiliary Heater communication lines

(under AC24V,over AWG24)

These wires should not make

contact with high voltage lines.

To indoor unit PCB

(CN-PTC)

AB AB

※

Wiring

Assembly Diagram

Aux heater

communication

lines

Step1. Open front panel. Step2. Assemble PRARH1 with cabinet.

Step3. Open the cover of PRARH1 and connect wires. Step4. Assemble control box cover and front panel.

Fig. A

Control box cover

screw

Insulation

Note: While connecting the PRARH1, attach insulation at the rear of the control box cover

where it receives screws as shown in Fig. A.

Please clean up the remaining wires after installation.

Installation Manual 9

ENGLISH

n 2 Way CST

Auxiliary Heater communication lines

(under AC24V,over AWG24)

These wires should not make

contact with high voltage lines.

To indoor unit PCB

(CN-PTC)

AB AB

※

Wiring

Assembly Diagram

Aux heater

communication

lines

Step1. Open front panel. Step2. Assemble PRARH1 with cabinet.

Step3. Open the cover of PRARH1 and connect wires. Step4. Assemble control box cover and front panel.

Fig. A

Control box cover

screw

Insulation

Note: While connecting the PRARH1, attach insulation at the rear of the control box cover

where it receives screws as shown in Fig. A.

Please clean up the remaining wires after installation.

10 Auxiliary Heater Relay Kit

n 4 Way CST

Auxiliary Heater communication lines

(under AC24V,over AWG24)

These wires should not make

contact with high voltage lines.

To indoor unit PCB

(CN-PTC)

Aux heater

communication lines

AB AB

Check the attached direction to the indoor unit.

Aux heater

communication lines

※

Wiring

Assembly Diagram

Aux heater

communication lines

Aux heater

communication lines

Aux heaterAux heater

communication linescommunication lines

Aux heater

communication lines

Aux heater

communication lines

Step1. Open front panel. Step2. Assemble PRARH1 with cabinet.

Step3. Open the cover of PRARH1 and connect wires. Step4. Assemble control box cover and front panel.

CAUTION

Fig. A

Control box cover

screw

Insulation

Note: While connecting the PRARH1, attach insulation at the rear of the control box cover

where it receives screws as shown in Fig. A.

Please clean up the remaining wires after installation.

Installation Manual 11

ENGLISH

Assembly Diagram

n Ceiling Suspended

D < 3.3ft

Auxiliary heater relay kit should be installed with in 3.3ft from the product.

Otherwise heater may cause malfunction.

Auxiliary Heater communication lines

(under AC24V,over AWG24)

These wires should not make

contact with high voltage lines.

To indoor unit PCB

(CN-PTC)

AB AB

※

Wiring

Aux heater

communication

lines

Step1. Mount relay kit on the wall. Step2. Connect wires and assemble cover.

Do not install PRARS0 at,

- Places which exposed to rain or any water.

Other wise it may leads to electric shock, fire, injury or sometimes even fatality.

CAUTION

Note: Please clean up the remaining wires after installation.

12 Auxiliary Heater Relay Kit

4. Electrical Wiring

Note

• Use only UL1996 approved heater.

• Do not the Duct Heater. Use Base Bord Heater instead.

CN-PTC1

PRARH1

Heater1

Relay Circuit

Resistance

Heater

AC24V

DC12V

CN_PTC

Relay

Electric Baseboard Heater

Heater

Terminal block

Heater2

Relay Circuit

Resistance

Heater

AC24V

Relay

Electric Baseboard Heater

Heater

Terminal block

Electrical Wiring

• The wire should not be exposed to outside otherwise it may leads to malfunction of

machine or sometimes fire due to wire damage.

• Wrong wiring also cause fire, malfunction or damage to the machine.

• The installation voltage should be with in 24V otherwise it may leads to electric shock,

fire, injury or fatality.

WARNING

Duct Heater Base Bord Heater

Installation Manual 13

ENGLISH

Installer Setting

Function Code Existing condition

Select existing condition

of each code by pressing

button.

(00: not installed,

01 : installed)

Press button to save.

If pressing button long for 3

seconds, it enters into Thermostat

installer setup mode.

- If pressing once shortly, it enters into

user setup mode. Please press

more than 3 seconds for sure.

If pressing button repeatedly, it moves to

the selected option function code as picture

below.

Pressing button will exit settings mode.

❈ After setup, it automatically gets out of

setup mode if there is no button input for

25 seconds.

❈ When exiting without pressing set button,

the manipulated value is not reflected.

Function

Auxiliary heater

Code

5. Installer Setting

Wired Remote Controller(Accessory)

Setting feature for indoor unit when Auxiliary Heater Relay Kit is newly installed, or installed unit is removed.

Installer setting mode is to set the detailed function of the remote controller.

If it is not properly set then it may leads to problem to the product , user injury as well

as property damage. Therefore these setting must be done by a certified installer.

Any installation or change carried out by a non certified person, he should be responsi-

ble for the results and it will void free service also.

CAUTION

If you want to operate Auxiliary Heater Relay Kit, you should have Wired or Wireless Remote Controller

below.

Model : PREMTB10U

14 Auxiliary Heater Relay Kit

Installer Setting

Function Function Code Setting Value

Remote Controller LCD

3 : Set to Auxiliary heater

Auxiliary heater

4 : Cancel Auxiliary heater

5 : Check Auxiliary heater Installation

Installer Setting Code Table

The indoor unit displays during the heating mode, the Auxiliary heater is automatically turned on, but it is not

displayed on the wireless remote controller.

NOTE

Wireless Remote Controller(Accessory)

It can only be set during heating operation.

Press the SET/CLEAR button to reserve or cancel the Electric

heater function.

Press the FUNCTION SETTING button

3 times.

Electric heater symbol will blink.

Model : PQWRHQ0FDB

Control map of AUX HEATER

Installation Manual 15

ENGLISH

n Mode 1. Normal

1) Function operation : It operates when Aux Heater was set by the Installer option of wired remote con-

troller, or when it was set by a wireless remote controller.

- Wired remote control installer function: 25:01

- Installer function setting by wireless remote control : 2.3 / Release : 2.4

2) The details of Aux heater control

- Heater output on/off is controlled depending on the room temperature during the heater on opera-

tion.

① Heater 1 on/off

While Heater1 Off, if Room Temp < Set Point -1.0 ℃ → Heater1 ON

While Heater1 On, if Room Temp ≥ Set Point → Heater1 OFF

② Heater 2 on/off

While Heater2 off, if Room Temp < Set Point 1.5℃ → ON

While Heater2 On, if Room Temp ≥ Set Point 0.5℃ → OFF

③ Heater delay Time

Heater output On: Heater 1 is On after 2 seconds from the Heater Off.

Heater 2 On is on after one minute

Heater output off : Others

※ It does not apply to some products.

6. Control map of AUX HEATER

Set temp

Heater 1

OFF

Heater 2

Set temp -0.5°C

Set temp -1.0°C

Set temp -1.5°C

16 Auxiliary Heater Relay Kit

Control map of AUX HEATER

n Mode 2. Primary Heater

1) Function operation

a. When primary heater is set by wired / wireless remote controller after the setting of aux heater

function, the Aux. heater is used as the main heating, and H/P used as the auxiliary heating con-

cept during the operation of Heating & Heater.

(In this case, the heating TH ON / OFF value is changed to the following set value.)

b. Installers CODE (Set 'Add Installers' at the Aux heater settings)

- Primary heater setting by wired remote controller: 36:01

- Primary heater setting by wired remote controller: 36:00

- Primary heater setting by wireless remote control : 1.A

- Primary heater release by wireless remote control : 1.B

2) Primary heater control details

- Heater output On/Off is controlled depending on the room temperature while heater operation is On.

① Heater1 On/Off

Ind. Temp ≥ Set Temp +0.5℃ → Heater Off

Ind. Temp < Set Temp -0.5℃ → Heater On (1st Stage Heat On)

② Heater2 On/Off

Ind. Temp ≥ Set Temp → Heater Off

Ind. Temp < Set Temp -1.0℃ → Heater On (2nd Stage Heat On)

③ Heating Thermal On / Off

Ind. Temp ≥ Set Temp -0.5℃ → Thermo. Off

Ind. Temp < Set Temp -1.5℃ → Thermo. On (3rd Stage Heat On)

④ Heater delay Time

Heater output On : Heater 1 is On after two seconds lapse from Heating & Heater Off, and Heater

2 is On after one minute lapse

Heater output off: Others

※ It does not apply to some products.

Set temp

Heater 1

OFF

OFF OFFON

Heater 2

TH ON/OFF

Set temp -0.5°C

Set temp +0.5°C

Set temp -1.0°C

Set temp -1.5°C

Troubleshooting Guide

Installation Manual 17

ENGLISH

7. Troubleshooting Guide

Symptom Check Action

AUX HEATER

does not work.

Is air conditioner power turned on?

- Check the circuit breaker.

- Check the AUX HEATER RELAY KIT installa-

tion status.

Is the cable correctly connected bete-

ween the air conditioner andAUX

HEATER RELAY KIT?

- Connect the cable between the air conditioner

and AUX HEATER RELAY KIT.

Is the cable correctly connected

between AUX HEATER and

AUX HEAER REWLAY KIT?

- Refer to the installation method in the installa-

tion manual and check again.

Is there any problem with wireless

remote controller?

(If wireless remote controller is used)

- Replace the battery or insert again according

to the polarity(+,-).

- If there is a leakage of the battery fluid in the

remote controller, replace the battery.

18 Auxiliary Heater Relay Kit

www.lg.com

MANUEL D'INSTALLATION

CLIMATISEUR

• Lisez ce manuel d'installation dans son intégralité avant d'installer le produit.

• L'installation doit être réalisée en respectant les normes locales en vigueur et

effectuée uniquement par un personnel qualiﬁé.

• Après l'avoir lu attentivement, conservez ce manuel d'installation aﬁn de

pouvoir vous y reporter ultérieurement.

TYPE : Kit relais du dispositif chauffant auxiliaire (pour produits Multi V)

MODÈLE : PRARH1

FRANÇAIS

2 Kit relais du dispositif chauffant auxiliaire

IMPORTANT !

ATTENTION

Toute installation, réglage, modification, entretien ou maintenance incorrect peut annuler la garantie.

Le poids de l'unité groupe compresseur-condenseur impose des procédures appropriées d'attention et de manipulation

lors des opérations de levage ou de déplacement afin d'éviter tout risque de blessures. Évitez surtout les contacts avec les bords tranchants ou pointus.

Consignes de sécurité

•

L'installation des équipements nécessite que les intervenants portent toujours des lunettes et des gants de sécurité.

•

Ne considérez jamais que l'alimentation électrique est déconnectée. Vérifiez toujours avec les appareils appropriés.

NOTE DESTINÉE AU REVENDEUR INSTALLATEUR

: Les modes d'emploi et garanties doivent être remis au client ou placés de façon

évidente à proximité de l'unité générateur d'air chaud / armoire de traitement d'air.

Lors du câblage :

Une décharge électrique peut causer des blessures graves ou un accident mortel.

Le câblage de ce système ne peut être confié qu'à un électricien qualifié et expérimenté.

•

Ne mettez pas l'appareil sous tension tant que tous les câblages et raccordements de tuyaux n'ont pas été terminés ou réalisés, puis vérifiés.

• Ce système utilise des tensions électriques élevées et dangereuses. Lors du câblage, reportez-vous soigneusement au

schéma de câblage et à ces instructions.

Tout raccordement incorrect ou mise à la terre incorrecte peut causer des accidents provoquant des blessures, voire la mort.

• La mise à la terre doit être effectuée conformément aux codes électriques locaux.

•

Branchez tous les câbles fermement. Un câblage desserré peut provoquer une surchauffe aux points de connexion avec le risque de déclenchement d'un incendie.

Lors de l'installation...

... dans un mur :

Vérifiez que le mur est suffisamment solide pour contenir le poids de l'appareil.

Il sera peut-être nécessaire de construire un cadre robuste en bois ou en métal comme complément de support.

... dans une pièce

Isolez de façon appropriée toute la tubulure présente dans la pièce afin de prévenir

toute "transpiration" avec le risque de voir le mur et le plancher endommagés par l'écoulement de

l'eau.

Lors des opérations d'entretien

• Avant d'ouvrir l'appareil pour des contrôles ou réparations des pièces électriques et du câblage,

mettez l'appareil hors tension (OFF) au niveau du boîtier d'alimentation principal (secteur).

• Une fois les opérations terminées, nettoyez le site et vérifiez bien qu'aucun déchet métallique ou

morceau de câblage n'ait été oublié à l'intérieur de l'appareil ayant fait l'objet de l'entretien.

AVERTISSEMENT

•

• Les informations contenues dans ce manuel s'adressent à des techniciens qualifiés habitués aux procédures de

sécurité et équipés des outils et instruments de test appropriés.

• Tout manquement à une lecture soignée et au suivi précis de toutes les instructions de ce manuel peut se traduire

par un dysfonctionnement des équipements, des dommages aux biens, des blessures et/ou accidents mortels.

Lisez cette fiche d'instructions entièrement avant d'installer le produit.

Ce système de climatisation répond strictement aux normes de sécurité et de fonctionnement. En tant que personne chargée de l'installation ou de l'entretien

de cet appareil, une part importante de votre travail d'installation ou d'entretien de ce système consiste à ce qu'il fonctionne efficacement en toute sécurité.

L'installation doit s'adapter aux codes du bâtiment local ou avec le National Electrical Code NFPA 70/ANSI C1-1993

(ouédition en vigueur), ainsi que le Code électrique canadien CSA C.22.1 Part1.

La page charge ...