DeWalt DCK621D2 Mode d'emploi

DCS391, DCS393

20V Max* 6-1/2" (165 mm) Cordless Circular Saw

Scie circulaire sans fil de 20 V max* 165 mm

Sierra circular inalámbrica de 20 V Máx* 165 mm

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

2

English

DCS391, DCS393 20V Max* 6-1/2" Cordless Circular Saw 3700 RPM

A. TRIGGER SWITCH LOCK-OFF BUTTON

B. TRIGGER SWITCH

C. BATTERY PACK

D. DEPTH ADJUSTMENT KNOB

E. SHOE

F. LOWER BLADE GUARD RETRACTING LEVER

G. LOWER BLADE GUARD

H. BLADE CLAMPING SCREW

I. KERF INDICATOR

J. BEVEL ADJUSTMENT KNOB

K. BLADE LOCK BUTTON (not shown)

L. AUXILIARY HANDLE

M. BATTERY RELEASE BUTTON

N. BLADE WRENCH

C

E

B

F

G

K

I

L

H

A

M

D

A

M

J

N

1

English

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

2

English

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

3

English

c) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Safety Instructions for All Saws

a) DANGER: Keep hands away from cutting area and

the blade. Keep your second hand on auxiliary handle,

or motor housing. If both hands are holding the saw, they

cannot be cut by the blade.

b) Do not reach underneath the workpiece. The guard cannot

protect you from the blade below the workpiece.

c) Adjust the cutting depth to the thickness of the workpiece.

Less than a full tooth of the blade teeth should be visible below

the workpiece.

d) Never hold piece being cut in your hands or across

your leg. Secure the workpiece to a stable platform. It

is important to support the work properly to minimize body

exposure, blade binding, or loss of control.

e) Hold power tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring. Contact with a “live” wire will also

make exposed metal parts of the power tool “live” and shock

the operator.

f) When ripping always use a rip fence or straight edge

guide. This improves the accuracy of cut and reduces the

chance of blade binding.

g) Always use blades with correct size and shape (diamond

versus round) of arbor holes. Blades that do not match the

mounting hardware of the saw will run eccentrically, causing

loss of control.

h) Never use damaged or incorrect blade washers or bolt.

The blade washers and bolt were specially designed for your

saw, for optimum performance and safety of operation.

Further Safety Instructions for All Saws

CAUSES AND OPERATOR PREVENTION OF KICKBACK:

– Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift up

and out of the workpiece toward the operator;

– When the blade is pinched or bound tightly by the kerf closing

down, the blade stalls and the motor reaction drives the unit

rapidly back toward the operator;

– If the blade becomes twisted or misaligned in the cut, the teeth

at the back edge of the blade can dig into the top surface of the

wood causing the blade to climb out of the kerf and jump back

toward the operator.

Kickback is the result of saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

a) Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line with

the blade. Kickback could cause the saw to jump backwards,

but kickback forces can be controlled by the operator, if proper

precautions are taken.

4

English

b) Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a build-

up of debris.

c) Lower guard should be retracted manually only for

special cuts such as “plunge cuts” and “compound cuts.”

Raise lower guard by retracting handle and as soon

as blade enters the material, the lower guard must be

released. For all other sawing, the lower guard should operate

automatically.

d) Always observe that the lower guard is covering the

blade before placing saw down on bench or floor. An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the time

it takes for the blade to stop after switch is released.

Additional Speciﬁ c Safety Instructions for

Circular Saws

WARNING: Do not use abrasive wheels or blades.

WARNING: Do not use water feed attachments.

• Use clamps or another practical way to secure and support

the workpiece to a stable platform. Holding the work by hand

or against your body leaves it unstable and may lead to loss of

control.

• Keep your body positioned to either side of the blade, but

not in line with the saw blade. KICKBACK could cause the saw

to jump backwards (see Causes and Operator Prevention of

Kickback and KICKBACK).

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

b) When blade is binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless

in the material until the blade comes to a complete

stop. Never attempt to remove the saw from the work

or pull the saw backward while the blade is in motion or

kickback may occur. Investigate and take corrective actions

to eliminate the cause of blade binding.

c) When restarting a saw in the workpiece, center the

saw blade in the kerf and check that saw teeth are not

engaged into the material. If saw blade is binding, it may

walk up or kickback from the workpiece as the saw is restarted.

d) Support large panels to minimize the risk of blade

pinching and kickback. Large panels tend to sag under their

own weight. Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or

improperly set blades produce narrow kerf causing excessive

friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must be

tight and secure before making cut. If blade adjustment

shifts while cutting, it may cause binding and kickback.

g) Use extra caution when making a “plunge cut” into

existing walls or other blind areas. The protruding blade

may cut objects that can cause kickback.

LOWER GUARD SAFETY INSTRUCTIONS

a) Check lower guard for proper closing before each use. Do

not operate the saw if lower guard does not move freely

and close instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally dropped, lower

guard may be bent. Raise the lower guard with the retracting

handle and make sure it moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

5

English

• Avoid cutting nails. Inspect for and remove all nails from lumber

before cutting.

WARNING: ALWAYS USE SAFETY GLASSES. Everyday

eyeglasses are NOT safety glasses. Also use face or dust mask if

cutting operation is dusty. ALWAYS wear certified safety equipment:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3).

• ANSI S12.6 (S3.19) hearing protection.

• NIOSH/OSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction

activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your

mouth, eyes, or lay on the skin may promote absorption of

harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other

injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face

and body. Always operate tool in well-ventilated area and provide for

proper dust removal. Use dust collection system wherever possible.

WARNING: ALWAYS wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

WARNING: ALWAYS use eye protection. All users and

bystanders must wear eye protection that conforms to ANSI Z87.1.

CAUTION: When not in use, place circular saw on a stable

surface, shoe side down, where it will not cause a tripping or

falling hazard. Some tools with large battery packs will stand upright

on the battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ............. volts A ............amperes

Hz ........... hertz W ........... watts

min .........minutes ......... alternating current

......direct current ......... alternating or direct

...........Class I Construction current

(grounded) no .......... no load speed

...........Class II Construction ........... earthing terminal

(double insulated) .......... safety alert symbol

BPM .......beats per minute …/min .... per minute

RPM .......revolutions per minute IPM ........impacts per minute

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include the

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

6

English

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below and

then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable liquids,

gases or dust. Inserting or removing the battery pack from the

charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. Do not

modify the battery pack in any way to fit into a non-

compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105°F (40°C)

(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in the

ON position.

WARNING: Fire hazard. Never attempt to open the battery pack

for any reason. If the battery pack case is cracked or damaged, do

not insert into the charger. Do not crush, drop or damage the battery

pack. Do not use a battery pack or charger that has received a sharp

blow, been dropped, run over or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry the battery

pack so that metal objects can contact exposed battery

terminals. For example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries can possibly

cause fires if the battery terminals inadvertently come in

contact with conductive materials such as keys, coins, hand

tools and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in

commerce or on airplanes (e.g., packed in suitcases and carry-on

luggage) UNLESS they are properly protected from short circuits.

So when transporting individual battery packs, make sure that the

battery terminals are protected and well insulated from materials that

could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

7

English

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs)

indicate that the costs to recycle these batteries (or

battery packs) at the end of their useful life have already

been paid by DEWALT. In some areas, it is illegal to

place spent nickel cadmium, nickel metal hydride or lithium ion

batteries in the trash or municipal solid waste stream and the RBRC

program provides an environmentally conscious alternative.

RBRC™, in cooperation with DEWALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or lithium

ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized DEWALT service center or

to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary

markings on the charger, battery pack and product using the

battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside the

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

DEWALT rechargeable battery packs. Other types of batteries may

overheat and burst resulting in personal injury and property damage.

NOTICE: Under certain conditions, with the charger plugged into the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature, such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil or any buildup of metallic

particles should be kept away from the charger cavities. Always unplug

the charger from the power supply when there is no battery pack in the

cavity. Unplug the charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging DEWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting

the charger. This will reduce the risk of damage to the electric plug

and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage

or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric

shock.

8

English

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is,

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The lower the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere

Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

More

Than

Not

More

Than

AWG

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety instructions

before using your charger. Consult the chart at the end of this manual

for compatibility of chargers and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an FIG. 1 C

appropriate outlet before inserting

the battery pack.

2. Insert the battery pack (C)

into the charger, as shown in

Figure 1, making sure the pack

is fully seated in charger. The

red (charging) light will blink

continuously, indicating that the

charging process has started.

3. The completion of charge will

be indicated by the red light

remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.

9

English

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.

PROBLEM POWER LINE

Some chargers have a problem powerline indicator. When the charger

is used with some portable power sources such as generators or

sources that convert DC to AC, the charger may temporarily suspend

operation, flashing the red light with two fast blinks followed by a pause.

This indicates the power source is out of limits.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65°F and

75°F (18° – 24°C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to the touch

while charging. This is a normal condition, and does not indicate

a problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

Indicator Light Operation

PACK CHARGING

PACK CHARGED

x

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

PROBLEM POWERLINE

Charge Indicators

This charger is designed to detect certain problems that can arise.

Problems are indicated by the red light flashing at a fast rate. If this

occurs, re-insert the battery pack into the charger. If the problem

persists, try a different battery pack to determine if the charger is

working properly. If the new pack charges correctly, then the original

pack is defective and should be returned to a service center or other

collection site for recycling. If the new battery pack elicits the same

trouble indication as the original, have the charger and the battery pack

tested at an authorized service center.

HOT/COLD DELAY

This charger has a hot/cold delay feature: when the charger detects a

battery that is hot, it automatically starts a delay, suspending charging

until the battery has cooled. After the battery has cooled, the charger

automatically switches to the pack charging mode. This feature

ensures maximum battery life. The red light flashes long, then short

while in the hot/cold delay mode.

10

English

3. A cold battery pack will charge at about half the rate of a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move the charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F – 75 °F

(18° – 24°C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse effect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug the charger before

attempting to clean.

7. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside the

charger. Electric shock may result.

WARNING: Burn hazard. Do not submerge the battery pack in

any liquid or allow any liquid to enter the battery pack. Never attempt

to open the battery pack for any reason. If the plastic housing of the

battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from direct

sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

Please refer to the front of this section for the list of components.

INTENDED USE

This heavy-duty circular saw is designed for professional wood cutting

applications.

DO NOT use under wet conditions or in presence of flammable liquids

or gases.

DO NOT let children come into contact with the tool. Supervision is

required when inexperienced operators use this tool.

OPERATION

WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

11

English

Installing and Removing the Battery Pack

(Fig. 2)

NOTE: For best results, make sure your battery pack is fully charged.

To install the battery pack (C) into the tool handle, align the battery

pack with the rails inside the tool’s handle and slide it into the handle

until the battery pack is firmly seated in the tool and ensure that it does

not disengage.

To remove the battery pack from the tool, press the release button (M)

and firmly pull the battery pack out of the tool handle. Insert it into the

charger as described in the charger section of this manual.

C

FIG. 2

M

R

FIG. 2A

FUEL GAUGE BATTERY PACKS (FIG. 2A)

Some DEWALT battery packs include a fuel gauge which consists of

three green LED lights that indicate the level of charge remaining in

the battery pack.

To actuate the fuel gauge, press and hold the fuel gauge button (R).

A combination of the three green LED lights will illuminate designating

the level of charge left. When the level of charge in the battery is below

the usable limit, the fuel gauge will not illuminate and the battery will

need to be recharged.

NOTE: The fuel gauge is only an indication of the charge left on the

battery pack. It does not indicate tool functionality and is subject to

variation based on product components, temperature and end-user

application.

For more information regarding fuel gauge battery packs, please call

1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.

com.

Trigger Switch (Fig. 3)

WARNING: This tool has no FIG. 3

BA

provision to lock the trigger switch

in the ON position and should

never be locked ON by any other

means.

Release the trigger switch lock-off

button (A) by pressing the button as

shown. Pull the trigger switch (B)

to turn the motor on. Releasing the

trigger switch turns the motor off.

Changing Blades (Fig. 4, 5)

TO INSTALL THE BLADE (FIG. 4, 5)

1. Place inner clamp washer (O) on saw spindle with the large flat

surface facing out toward the blade (Fig. 4A, 4B).

2. Retract the lower blade guard (G) and place blade on saw spindle

against the inner clamp washer, making sure that the blade

will rotate in the proper direction (the direction of the rotation

arrow on the saw blade and the teeth must point in the same

12

English

direction as the direction of rotation arrow on the lower blade

guard). Do not assume that the printing on the blade will always

be facing you when properly installed. When retracting the lower

blade guard to install the blade, check the condition and operation

of the lower blade guard to assure that it is working properly. Make

sure it moves freely and does not touch the blade or any other

part, in all angles and depths of cut.

FIG. 4A

O

K

L

F

P

H

G

3. Place outer clamp washer (P) on saw spindle with the large flat

surface against the blade with beveled side facing out.

4. Thread blade clamping screw (H) into saw spindle by hand (screw

has left-hand threads and must be turned counterclockwise to

tighten).

5. Depress the blade lock button (K) while turning the saw spindle

with the blade wrench (N) until the blade lock engages and the

blade stops rotating (Fig. 5).

6. Tighten the blade clamping screw firmly with the blade wrench.

NOTE: Never engage the blade lock while saw is running, or engage

in an effort to stop the tool. Never turn the saw on while the blade lock

is engaged. Serious damage to your saw will result.

H

PO

SPINDLE

BLADE

O

P

H

FIG. 4B

13

English

TO REPLACE THE BLADE (FIG. 4, 5)

1. To loosen the blade clamping screw (H), depress the blade lock

button (K) and turn the saw spindle with the blade wrench (N) until

the blade lock engages and the blade stops rotating. With the

blade lock engaged, turn the blade clamping screw clockwise with

the blade wrench (screw has left-hand threads and must be turned

clockwise to loosen).

TIGHTEN

(counterclockwise)

FIG. 5

LOOSEN

(clockwise)

K

N

2. Remove the blade clamping screw (H) and outer clamp washer (P)

only. Remove old blade.

3. Clean any sawdust that may have accumulated in the guard or

clamp washer area and check the condition and operation of the

lower blade guard as previously outlined. Do not lubricate this area.

4. Select the proper blade for the application (see Blades). Always

use blades that are the correct size (diameter) with the proper size

and shape center hole for mounting on the saw spindle. Always

assure that the maximum recommended speed (rpm) on the saw

blade meets or exceeds the speed (rpm) of the saw.

5. Follow steps 2 through 6 under To Install the Blade, making sure

that the blade will rotate in the proper direction.

LOWER BLADE GUARD

WARNING: The lower blade guard is a safety feature which

reduces the risk of serious personal injury. Never use the saw

if the lower blade guard is missing, damaged, misassembled

or not working properly. Do not rely on the lower blade

guard to protect you under all circumstances. Your safety

depends on following all warnings and precautions as well

as proper operation of the saw. Check lower blade guard for

proper closing before each use as outlined in Further Safety

Instructions for All Saws. If the lower blade guard is missing

or not working properly, have the saw serviced before using.

To assure product safety and reliability, repair, maintenance

and adjustment should be performed by an authorized service

center or other qualified service organization, always using

identical replacement parts.

Blades

WARNING: To minimize the risk of eye injury, always use eye

protection. Carbide is a hard but brittle material. Foreign objects in

the workpiece such as wire or nails can cause tips to crack or break.

Only operate saw when proper saw blade guard is in place. Mount

blade securely in proper rotation before using, and always use a

clean, sharp blade.

WARNING: Do not cut ferrous metals (steel), masonry, glass,

masonry-type planking, cement board or tile with this saw.

Do not use abrasive wheels or blades. A dull blade will cause slow

inefficient cutting, overload on the saw motor, excessive splintering,

and could increase the possibility of kickback. Please refer to the

table below to determine the correct size replacement blade for your

model saw.

14

English

Blade Diameter Teeth Application

DW9155 6-1/2" (165mm) 18 General purpose cutting

DW9154 6-1/2" (165mm) 24 Smooth wood cutting

DW9153 6-1/2" (165mm) 90 Non-carbide, plywood/

vinyl siding cutting

If you need assistance regarding blades, please call 1-800-4-DEWALT

(1-800-433-9258).

KICKBACK

Kickback is a sudden reaction to a pinched, bound or misaligned saw

blade, causing an uncontrolled saw to lift up and out of the workpiece

toward the operator. When the blade is pinched or bound tightly by the

kerf closing down, the blade stalls and the motor reaction drives the

unit rapidly back toward the operator. If the blade becomes twisted or

misaligned in the cut, the teeth at the back edge of the blade can dig

into the top surface of the wood causing the blade to climb out of the

kerf and jump back toward the operator.

Kickback is more likely to occur when any of the following conditions

exists.

1. IMPROPER WORKPIECE SUPPORT

A. Sagging or improper lifting of the cut off piece can cause

pinching of the blade and lead to kickback (Fig. 12).

B. Cutting through material supported at the outer ends only can

cause kickback. As the material weakens it sags, closing down

the kerf and pinching the blade (Fig. 12).

C. Cutting off a cantilevered or overhanging piece of material from

the bottom up in a vertical direction can cause kickback. The

falling cut off piece can pinch the blade.

D. Cutting off long narrow strips (as in ripping) can cause kickback.

The cut off strip can sag or twist closing the kerf and pinching

the blade.

E. Snagging the lower guard on a surface below the material being

cut momentarily reduces operator control. The saw can lift

partially out of the cut increasing the chance of blade twist.

2. IMPROPER DEPTH OF CUT SETTING ON SAW

To make the most efficient cut, the blade should protrude only far

enough to expose one-half of a tooth as shown in Figure 7. This

allows the shoe to support the blade and minimizes twisting and

pinching in the material. See the section titled Cutting Depth

Adjustment.

3. BLADE TWISTING (MISALIGNMENT IN CUT)

A. Pushing harder to cut through a knot, a nail, or a hard grain area

can cause the blade to twist.

B. Trying to turn the saw in the cut (trying to get back on the

marked line) can cause blade twist.

C. Overreaching or operating the saw with poor body control (out

of balance), can result in twisting the blade.

D. Changing hand grip or body position while cutting can result in

blade twist.

E. Backing up the saw to clear blade can lead to twist.

4. MATERIALS THAT REQUIRE EXTRA ATTENTION

A. Wet lumber

B. Green lumber (material freshly cut or not kiln dried)

C. Pressure treated lumber (material treated with preservatives or

anti-rot chemicals)

5. USE OF DULL OR DIRTY BLADES

Dull blades cause increased loading of the saw. To compensate,

an operator will usually push harder which further loads the unit

and promotes twisting of the blade in the kerf. Worn blades may

also have insufficient body clearance which increases the chance

of binding and increased loading.

15

English

6. LIFTING THE SAW WHEN MAKING A BEVEL CUT

Bevel cuts require special operator attention to proper cutting

techniques – especially guidance of the saw. Both blade angle to

the shoe and greater blade surface in the material increase the

chance for binding and misalignment (twist) to occur.

7. RESTARTING A CUT WITH THE BLADE TEETH JAMMED

AGAINST THE MATERIAL

The saw should be brought up to full operating speed before

starting a cut or restarting a cut after the unit has been stopped

with the blade in the kerf. Failure to do so can cause stalling and

kickback.

Any other conditions which could result in pinching, binding, twisting,

or misalignment of the blade could cause kickback. Refer to the

sections Further Safety Instructions for All Saws and Blades

for procedures and techniques that will minimize the occurrence of

kickback.

Cutting Depth Adjustment (Fig. 6, 7)

1. Hold the saw firmly and loosen (clockwise) the depth adjustment

knob (D) and move shoe to obtain the desired depth of cut.

2. Make sure the depth adjustment knob has been retightened

(counterclockwise) before operating saw.

FIG. 7

J

D

FIG. 6

For the most efficient cutting action, set the depth adjustment so that

one-half tooth of the blade will project below the material to be cut.

This distance is from the tip of the tooth to the bottom of the gullet in

front of it. This keeps blade friction at a minimum, removes sawdust

from the cut, results in cooler, faster sawing and reduces the chance

of kickback. A method for checking for correct cutting depth is shown

in Figure 7. Lay a piece of the material you plan to cut along the side

of the blade, as shown, and observe how much tooth projects beyond

the material.

Bevel Angle Adjustment (Fig. 7)

The full range of the bevel adjustment is from 0° to 50°. The quadrant is

graduated in increments of 1°. On the front of the saw is a bevel angle

adjustment mechanism consisting of a calibrated quadrant and a bevel

adjustment knob (J).

TO SET THE SAW FOR A BEVEL CUT

1. Loosen (counterclockwise) the bevel adjustment knob (J) and tilt

shoe to the desired angle by aligning the pointer with the desired

angle mark.

2. Retighten knob firmly (clockwise).

Shoe Adjustment for 90°Cuts (Fig. 8)

IF ADDITIONAL ADJUSTMENT IS NEEDED: FIG. 8

Q

J

1. Adjust the saw to 0° bevel.

2. Retract the lower blade guard. Place the

saw on blade side.

3. Loosen bevel adjustment knob (J). Place a

square against the blade and shoe to adjust

the 90° setting.

4. Turn the calibration screw (Q) so that the

shoe will stop at the proper angle.

16

English

5. Confirm the accuracy of the setting by checking the squareness of

an actual cut on a scrap piece of material.

Kerf Indicator (Fig. 9)

The front of the saw shoe has a kerf indicator (I)

I

FIG. 9

for vertical and bevel cutting. This indicator

enables you to guide the saw along cutting

lines penciled on the material being cut. The

kerf indicator lines up with the left (outer) side of

the saw blade, which makes the slot or “kerf”

cut by the moving blade fall to the right of the

indicator. Guide along the penciled cutting line

so that the kerf falls into the waste or surplus

material.

Workpiece Support (Fig. 10–12)

WARNING: It is important to support the work properly and to

hold the saw firmly to prevent loss of control which could cause

personal injury. Figure 10 illustrates proper hand support of the saw.

Maintain a firm grip with both hands on the saw and position your

body and arm to allow you to resist kickback if it occurs. ALWAYS

TURN OFF TOOL AND REMOVE BATTERY BEFORE MAKING ANY

ADJUSTMENTS!

FIG. 10

Figure 10 shows proper sawing position. Note that hands are kept away

from cutting area. To avoid kickback, DO support board or panel

NEAR the cut (Fig. 11). DON’T support board or panel away from the

cut (Fig. 12).

Place the work with its “good” side – the one on which appearance is

most important – down. The saw cuts upward, so any splintering will

be on the work face that is up when you cut it.

SUPPORT

DO support board or panel NEAR the cut.

FIG. 11

DON’T support board or panel AWAY from the cut.

FIG. 12

17

English

Cutting (Fig. 10)

Place the wider portion of the saw shoe on that part of the workpiece

which is solidly supported, not on the section that will fall off when the

cut is made. As an example, Figure 10 illustrates the RIGHT way to

cut off the end of a board. Always clamp work. Don’t try to hold short

pieces by hand! Remember to support cantilevered and overhanging

material. Use caution when sawing material from below.

Be sure saw is up to full speed before blade contacts material to be cut.

Starting saw with blade against material to be cut or pushed forward

into kerf can result in kickback. Push the saw forward at a speed which

allows the blade to cut without laboring.

Hardness and toughness can vary even in the same piece of material,

and knotty or damp sections can put a heavy load on the saw. When

this happens, push the saw more slowly, but hard enough to keep

working without much decrease in speed. Forcing the saw can cause

rough cuts, inaccuracy, kickback, and over-heating of the motor.

Should your cut begin to go off the line, don’t try to force it back on.

Release the trigger switch and allow blade to come to a complete stop.

Then you can withdraw the saw, sight anew, and start a new cut slightly

inside the wrong one. Withdraw the saw if you must shift the cut. Forcing

a correction inside the cut can stall the saw and lead to kickback.

IF SAW STALLS, RELEASE THE TRIGGER SWITCH AND BACK THE

SAW UNTIL IT IS LOOSE. BE SURE BLADE IS STRAIGHT IN THE

CUT AND CLEAR OF THE CUTTING EDGE BEFORE RESTARTING.

As you finish a cut, release the trigger switch and allow the blade

to stop before lifting the saw from the work. As you lift the saw, the

spring-tensioned lower blade guard will automatically close under the

blade. Remember the blade is exposed until this occurs. Never reach

under the work for any reason. When you have to retract the lower

blade guard manually (as is necessary for starting pocket cuts), always

use the retracting lever.

WARNING: When cutting thin strips, be careful to ensure that

small cutoff pieces don’t hang up on the inside of the lower blade

guard.

RIPPING (FIG. 13)

Ripping is the process of cutting wider boards into narrower strips –

cutting grain lengthwise. Hand guiding is more difficult for this type of

sawing and the use of a DEWALT rip fence is recommended.

INSTALL RIP FENCE

IN THIS DIRECTION

FIG. 13

POCKET CUTTING (FIG. 14) FIG. 14

WARNING: Never tie the

lower blade guard in a raised

position. Never move the saw

backwards when pocket cutting.

This may cause the saw to raise

up off the work surface, which

could cause injury.

A pocket cut is one that is

made in a floor, wall or other

flat surface.

1. Adjust the saw shoe so

the blade cuts at desired

depth.

18

English

2. Tilt the saw forward and rest front of the shoe on material to be cut.

3. Using the lower blade guard retracting lever, retract the lower

blade guard to an upward position. Lower the rear of the shoe until

the blade teeth almost touch the cutting line.

4. Release the lower blade guard (its contact with the work will keep

it in position to open freely as you start the cut). Remove your

hand from the lower blade guard retracting lever and firmly grip

the auxiliary handle, as shown in Figure 14. Position your body and

arm to allow you to resist kickback if it occurs.

5. Make sure blade is not in contact with cutting surface before

starting saw.

6. Start the motor and gradually lower the saw until its shoe rests flat

on the material to be cut. Advance saw along the cutting line until

cut is completed.

7. Release the trigger switch and allow the blade to stop completely

before withdrawing the blade from the material.

8. When starting each new cut, repeat the above steps.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do not

use water or any cleaning solutions.

Lubrication

Self lubricating ball and roller bearings are used in the tool and

relubrication is not required. However, it is recommended that, once

a year, you take or send the tool to a certified service center for a

thorough cleaning, inspection, and lubrication of the gear case.

Accessories

WARNING: Since accessories, other than those offered by

DEWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only DEWALT recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available at

extra cost from your local service center. If you need any assistance

in locating any accessory, please contact DEWALT Industrial Tool Co.,

701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT

(1-800-433-9258) or visit our website: www.dewalt.com.

Repairs

The charger and battery pack are not serviceable. There are no

serviceable parts inside the charger or battery pack.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustments (including brush inspection and replacement) should

be performed by a DEWALT factory service center, a DEWALT

authorized service center or other qualified service personnel. Always

use identical replacement parts.

La page charge ...

DeWalt DCK621D2 Mode d'emploi

DeWalt DCK621D2 Mode d'emploi

dans d''autres langues