Haier QACT17A Manuel utilisateur

Table of Contents

Parts and Functions

Interface Display .........................................................................1

Icons ..............................................................................................2

Dip Switch ...................................................................................4

Operation

Mode Key ....................................................................................6

Fan Key ........................................................................................6

Temperature Adjustment Keys .................................................7

Special Function

Special Function Selection ..........................................................8

Installer Settings

Adjust ECO Parameters ...........................................................10

Child Lock ................................................................................10

Lock Settings ............................................................................11

Fahrenheit / Celsius ..................................................................11

Temperature Compensation ...................................................12

Forced Defrost/Cooling/Heating ............................................12

Error Checks .............................................................................13

Mode Restriction ......................................................................14

Mode Combination Settings ....................................................15

Wiring Instruction .................................................................... 15

Wired Controller

Installation and Operation Manual

QACT17A

• Please read this manual before use

• Please keep this manual for future reference.

49-5000061 Rev. 2

GEA 02-19

Full display

1

Parts and Functions

Interface Display

/

2

Room temperature display ( dip switch SW1-2

on).

Set temperature display

Filter

HRV (Heat Reclaim Ventilation), if HRV

function is set, it will display this icon

Error icon displays detected fault

ECO mode on

Central/lock when connected to a central

controller

UP/DOWN louver swing

LEFT/RIGHT louver swing

Child lock on

Parts and Functions

Icons

Master / Slave

Master / Slave wired controller

Quiet Fan Speed

(some models)

Low Fan Speed

Medium Fan Speed

High Fan Speed

Turbo Fan Speed

(some models)

Auto Fan speed is indicated by the display automatically

stepping from low to high repeatedly.

Auto Mode

Cooling Mode

Heating Mode

Fan Mode

3

Parts And Functions

4

Dip switch denition

Dip Switch SW1

Dip Switch

SW1 ON OFF Default

Sw1-1 Slave wired controller Master wired controller OFF

Sw1-2 Room temperature

display on

Room temperature

display o

OFF

Sw1-3

Room temperature

collected from indoor unit

Room temperature

collected from controller

OFF

Sw1-4

System remains o after

power loss

Auto restart after power

loss

OFF

Sw1-5

Old protocol (models

developed before Aug.

2013)

New protocol OFF

Sw1-6 Backlight always on

Backlight 15 second auto

time out

OFF

Sw1-7

Reserved

Reserved OFF

Sw1-8 Reserved Reserved OFF

5

Dip Switch SW2

Initialization

When the mini-split system is powered on 88.8 will ash between

the Room Temperature display and the Set Temperature display

until communication is established with the indoor unit.

Press to power ON or power OFF the control. A tone will be

heard with every button press or when a command is received by

a remote control. If a conicting command is received, then the

tone will sound 3 times.

Audible Alert

Dip Switch

SW2 ON OFF Default

Sw2-1 Mode Lock Normal OFF

Sw2-2

No button conrmation tone. (Tone will

still sound when command is sent by

wireless remote.

Tone on OFF

Sw2-3 Reserved Reserved OFF

Sw2-4 Reserved Reserved OFF

Quiet Fan Speed

(some models)

Low Fan Speed

Medium Fan Speed

High Fan Speed

Turbo Fan Speed

(some models)

6

Mode key:

•

Each press of the MODE button will change the operating mode

from Auto – Cool – Heat – Fan – Dry (Dehumidication) – Auto …

• Each mode has its initial default fan speed.

Mode Key / Fan Key

Mode Fan speed Temperature

Auto Auto 76°F

Cool High 76°F

Heat Auto 76°F

Fan Low No temperature display

Dry (Dehumidication) Auto 76°F

Initial

State

Fan Key:

Each press of the FAN button will change the fan speed from

Auto – Quiet (some models) – Low – Medium – High – Turbo

(some models) – Auto …

7

Temperature Adjustment Keys: /

• Press the TEMP+ or TEMP- keys to change the temperature by

1°F increments.

• The temperature set point range for Auto, Cooling, Heating

and Dry (Dehumidication) is 60°F~86°F (If ECO is on,

then temperature range will change per the ECO setting

parameters).

• The temperature is set independently under Auto, Cooling,

Heating and Dehumidify modes. Once the temperature is set

in each mode the setting will be saved for that mode.

• In fan mode, Temp +/- keys do not work.

Temperature

8

Special Function Selection:

With the control powered on, press and hold the TEMP+ for

5 seconds to enter the special function menu. All the special

function icons will display. Use the TEMP+ and TEMP- buttons to

move between icons. Use FAN button to select function.

Function Selection

Full display

9

Function Selection

50

10

Adjust ECO Parameters:

• Cooling: Power on the unit. Adjust set temperature to 86°F.

Press and hold FAN and TEMP+ for 5 seconds. The minimum

allowable set temperature will be displayed in the top right

corner. Use TEMP+/- to change the parameter, then press FAN

save. The default minimum temperature is 73°F.

• Heating: Power on the unit. Adjust set temperature 60°F.

Press and hold FAN and TEMP- for 5 seconds. The maximum

allowable set temperature will be displayed in the top right

corner. Press TEMP+/- to change the parameter, then press

FAN to save. The default maximum temperature is 79°F.

• Dry (Dehumidication) ECO parameters are the same as Cooling.

Child Lock:

• Press and hold TEMP+ and TEMP- for 5 seconds to activate/

deactivate the Child Lock function. When the Child Lock

function is active, will appear.

Installer Settings

11

Central/Lock Function: /

Function is active only when system has a central control, such as

the YCZ-A004. This setting is activated only by the central Control.

Fahrenheit Setting and Display:

• Fahrenheit to Celsius: Adjust set temperature to lowest

setting; 60°F when ECO is o. Press and hold TEMP- for 15

seconds. During the 15 second count the display will beep

once at 5 seconds and display error codes. Then after another

5 seconds, the display will beep once again and display 00,

after 5 more seconds the display will change to Celsius.

• Celsius to Fahrenheit: Adjust set temperature to highest

setting; 30°C when Eco is o. Press and hold TEMP+ for 15

seconds. During the 15 second count, the display will beep

once at 5 seconds and enter Special Functions menu. Then

after another 5 seconds, the display will show 00, after 5 more

seconds the display will change to Fahrenheit.

Lock Settings / Fahrenheit Setting

Central Control On/O function only available.

Central Lock No functions available.

12

Set Temperature Compensation:

• With the display o, press and hold the FAN button for 5 seconds. The

display will then show 0 (default) or current compensation setting. Use

TEMP+/- buttons to adjust the compensation. Compensation can be

set in 1° increments

+/- 8°F (0.5°C increments up to +/-4°C).

• Temperature compensation changes the ambient temperature

reading. If the system is sensing the ambient temperature at 72°F

and the compensation is set to -2° then the system will use 70°F in its

operation to heat or cool.

Forced Defrost:

• Set to Heating mode, high fan, and 86°F (30°C), or highest temperature

if ECO is on. Press TEMP+ 6 times within 5 seconds. Three tones will

conrm that the unit is in forced defrost mode.

Forced Cooling:

• Set mode to Cool. Tap ON/OFF. Tap any button, except ON/OFF, to

light the display. Press and hold ON/OFF for 5 seconds. LL will display

and the control will beep twice. To exit, turn o control and turn it on

again.

Forced Heating:

• Set mode to Heat. Tap ON/OFF. Tap any button, except ON/OFF, to

light the display. Press and hold ON/OFF for 5 seconds. HH will display

and the control will beep twice. To exit, turn o control and turn it on

again.

Temperature Compensation

13

How to check error:

• If there is an error, will display.

• Check error: Press and hold TEMP- button for 5 seconds. The

error history will appear in the top right corner. The current

error will appear in the middle of the screen. If there is no error,

“--” will display.

Error Checks

14

Mode Restriction Function:

• When SW2-1 is on, the system mode lock is on. This will lock

the mode to Heat, Cool, Dry or Fan. No button press can

change mode. All other control functions are available such as

fan speed, set temperature, and on/o.

• Mode can still be changed with a wireless control, another

wired control, or a central control.

• When setting mode lock, have control set to desired mode. Set

dipswitch SW2-1 to ON. Disconnect and reconnect system

power.

Checking Parameters (only applies to some models):

• Press and hold TEMP+ for 10 seconds to check the parameters.

The parameters will appear in the middle of the screen to

show indoor address (00-15), Letters will appear after decimal

display (AbCdEF). The detailed parameters will show on the top

right corner. See table for denitions.

• If the control is connected to multiple indoor units, each indoor

unit can be viewed by pressing the FAN button. Then use

TEMP+/- to switch between connected indoor units.

Mode Restriction

A B C

15

• With the control o, press

and hold the MODE button

for 10 seconds. Use the FAN

button to change available

modes of operation. 4 is

default.

Mode Combination Setting

A: One control on one indoor

Indoor 1

Wired controller

Polar wire

Wired controller

Wired Controller Wiring Instruction

Wiring Connections

1. Cassette (AB…AL…MVAB…MVAL…)

Ducted (AD…AM…MVAD…MVAH…)

MRV Wall Mount (MVAW…)

2 Non-MRV Wall mount (AW...)

Indoor PCB board

Wired controller

LED3/R

SW1

CN4

CN3

CN5

CN1

A B C

CN2

1 2 3 4

LED1/R LED2/G

WK-B

LED4/G

A B C

Display Description Value

A Indoor sensor - Ambient (Tai) Temperature °F (°C)

b Indoor sensor - Vapor (Tc1) Temperature °F (°C)

C Indoor sensor - Liquid (Tc2 Temperature °F (°C)

d Indoor EEV position Half of actual position

E Indoor unit address Shown in hexadecimal

F Indoor unit central address Shown in hexadecimal

Parameter Inquiry:

Mode Combination Setting:

16

A B C

Indoor 2

Wired controller

A B C

Indoor 1

Wired controller

A B C

Indoor N

Wired controller

Indoor 15

Wired controller

Indoor 16

(master unit)

Wired controller

Control wiring of wired

controller, polar.

Wired controller

B: One Controller for up to 16 indoor

1. Cassette (AB…AL…MVAB…MVAL…)

Ducted (AD…AM24…MVAD…MVAH…)

MRV Wall Mount (MVAW…)

A B C

Indoor 2

Wired controller

A B C

Indoor 1

Wired controller

A B C A B C

Indoor N

Wired controller

Indoor 15

Wired controller

Indoor 16

(master unit)

Wired controller

Control wiring of wired

controller, polar.

Wired controller

2. Ducted (AM36...AM48…)

• Addressing Indoor Units

• Each indoor unit must hvae a unique

address.

• Compact Cassette (AB…) use SW02_1-4

• Large Cassette (AL…) use SW3_5-8

• Slim Duct (AD…) use SW03_1-4

• High Static Duct (AM24…) use SW03_5-8

• High Static Duct (AM36…AM48…) use

SW02_1-4

• All MRV indoor (MV…) use SW01_1-4

Dipswitch position Dipswitch position

Unit # 1 2 3 4 Unit # 1 2 3 4

5 6 7 8 5 6 7 8

0* o o o o 8 on o o o

1 o o o on 9 on o o on

2 o o on o 10 on o on o

3 o o on on 11 on o on on

4 o on o o 12 on on o o

5 o on o on 13 on on o on

6 o on on o 14 on on on o

7 o on on on 15 on on on on

* Unit 0 is connected directly to the control and is master

17

3. Non-MRV Wall Mount (AW...)

Wiring Connections

SW1

Wired controller

Unit 0

... ...

(master unit)

Unit 1

Unit 15

A B C

A B

B

C

A

A B C

A B

C

SW1

High Wall

WK-B

(1) The rst high wall indoor unit to

connect with WK-B is considered as

master unit 0.

(2) Remove the jumpers on CN3 and CN4.

(3) The wired control must connect to CN1

of the WK-B master unit (unit 0).

(4) Connect the CN2 on the master unit

(unit 0) to the next WK-B slave unit (unit 1)

CN1 or CN2. Only the master unit (unit 0)

must use CN1 for the control. All others

may use CN1 or CN2. See Picture 2.2.

(5) Set the dipswitch address of the

WK-B adapter. The adapters ship with all

switches o (master).

C:

Two controllers on one indoor

Notice: For wired controller connection and warranty details, please follow

the corresponding indoor unit installation instructions.

LED3/R LED4/G

A

B

C

A

B

C

Wired controller Wired controller

Polar wire

SW1

CN4

CN3

CN5

CN1

A B C

CN2

1 2 3 4

LED1/R LED2/G

WK-B

Indoor PCB board

2. Non-MRV Wall Mount (AW…)1. Cassette ( AB…AL…MVAB…MVAL…)

Ducted (AD…AM…MVAD…MVAH…)

MRV Wall Mount (MVAW…)

A B C

Indoor 1

Wired controller

Polar wire

Wired controller

Polar wire

Wired controller

Dipswitch position Dipswitch position

Unit # 1 2 3 4 Unit # 1 2 3 4

0* o o o o 8 on o o o

1 o o o on 9 on o o on

2 o o on o 10 on o on o

3 o o on on 11 on o on on

4 o on o o 12 on on o o

5 o on o on 13 on on o on

6 o on on o 14 on on on o

7 o on on on 15 on on on on

* Unit 0 is connected directly to the control and is master

18

C

B

A

red

yellow

white

Wired Controller Wiring Instruction

Communication Wiring

*Ground only one end of the shielded cable

Wiring Diagrams

Communication wiring length (m/ft)

Wire Size

< 100m/328ft

0.3mm

2

x3-core shielded wire

(22AWG,3wire)

≥100m/328ft and <200m/656ft

0.5mm

2

x3-core shielded wire

(20AWG,3wire)

≥200m/656ft and <300m/984ft

0.75mm

2

x3-core shielded

wire (18AWG,3wire)

≥300m/984ft and <400m/1312ft

1.25mm

2

x3-core shielded wire

(16AWG,3wire)

≥400m/1312ft and <500m/1640ft

2mm

2

x3-core shielded wire

(14AWG,3wire)

19

2. Secure the back panel to the

wall using screws.

3. Connect the control wires.

4. Attach the control to the

back panel by aligning the

bottom tabs and then press-

ing the top edge.

Wired Controller Wiring Instruction

Installation Diagrams

1. To take the front panel

and back panel apart,

slide the front panel up

and press down on the

back panel.

La page charge ...

Haier QACT17A Manuel utilisateur

Haier QACT17A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents