Samsung LN40A450 Manuel utilisateur

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care center.

Comment contacter Samsung dans le monde

Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service

Consommateurs Samsung.

Country

Customer Care Center

Web Site Address

CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca

Samsung Electronics Canada Inc., Customer

Service 55 Standish Court Mississauga,

Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc.,

Service à la Clientèle 55 Standish Court

Mississauga, Ontario L5R 4B2 Canada

U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com

Samsung Electronics America, Inc.

105 Challenger Road

Ridgefield Park, NJ 07660-0511

LCD TV

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

To receive a more complete service, please

register your product at

www.samsung.com/global/register

Model Serial No.

BN68-01395C-00

BN68-01395C-Cover.indd 1 2008-02-20 ¿ÀÀü 7:25:20

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image retention is also

known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still

image.

• Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and

center of the screen caused by the difference of light emission on the screen.

Playing a DVD or a game console may cause a similar effect to the screen.

Damages caused by the above effect are not covered by the Warranty.

• Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Important Warranty Information Regarding Television Format Viewing

Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format

full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen

if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as

the dark side-bars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total

television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or

computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the

above guidelines can cause uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in the LCD picture. To

avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.

On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format selection and use,

as well as burned-in images, are not covered by your Samsung limited warranty.

U.S.A Only

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. In particular,

this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396, 5,539,829, 5,606,618,

5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080, and under US Published Patent

Application No. 2001-44713-A1.

This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial

use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product

unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only

covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights

are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Other countries

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is

limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license

does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process

conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of

this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under

this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT

Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics

(SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide

Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG products purchased

in the United States, for the warranty period originally specified, and to the Original Purchaser only.

The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this Statement, the Original

Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation to and from

the Service Center is the responsibility of the purchaser.

Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the

product.

Excluded, but not limited to, are any originally specified provisions for, in-home or on-site services, minimum or maximum repair times,

exchanges or replacements, accessories, options, upgrades, or consumables.

For the location of a SAMSUNG Authorized Service Center, please call toll-free:

In the United States : 1-800-SAMSUNG (1-800-726-7864) In Canada : 1-800-SAMSUNG

See the warranty card for more information on warranty terms.

➣

BN68-01395A-Eng-0202.indd 1 2008-02-20 ¿ÀÀü 6:11:13

Contents

English

GENERAL INFORMATION

List of Features ............................................................................. 2

Accessories

..................................................................................2

Viewing the Control Panel

...........................................................3

Viewing the Connection Panel

.................................................... 4

Remote Control

............................................................................ 6

Installing Batteries in the Remote Control

.................................... 7

CONNECTIONS

(LN26A450C1D, LN40A450C1D)

Connecting VHF and UHF Antennas ............................................ 7

Connecting Cable TV

................................................................... 8

Connecting a DVD Player or Cable Box/Satellite receiver

(Set-Top Box) via HDMI ................................................................ 9

Connecting a DVD Player or Cable Box/Satellite receiver

(Set-Top Box) via DVI ................................................................... 9

Connecting a DVD Player or Cable Box/Satellite receiver

(Set-Top Box) via Component cables ......................................... 10

Connecting a Camcorder

.......................................................... 10

Connecting a VCR

...................................................................... 11

Connecting a Digital Audio System

............................................ 12

Connecting an Amplier/DVD Home Theater

............................. 12

Connecting a PC

........................................................................ 13

CONNECTIONS

(LN32A450C1D, LN37A450C1D)

Connecting VHF and UHF Antennas .......................................... 14

Connecting Cable TV

................................................................. 15

Connecting a DVD Player or Cable Box/Satellite receiver

(Set-Top Box) via HDMI .............................................................. 16

Connecting a DVD Player or Cable Box/Satellite receiver

(Set-Top Box) via DVI ................................................................. 16

Connecting a DVD Player or Cable Box/Satellite receiver

(Set-Top Box) via Component cables ......................................... 17

Connecting a Camcorder

.......................................................... 17

Connecting a VCR

...................................................................... 18

Connecting a Digital Audio System

............................................ 19

Connecting an Amplier/DVD Home Theater

............................. 19

Connecting a PC

........................................................................ 20

OPERATION

Turning the TV On and Off ......................................................... 21

Plug & Play Feature

................................................................... 21

Changing Channels

....................................................................22

Adjusting the Volume

.................................................................. 23

Viewing the Display

.................................................................... 23

Viewing the Menus

..................................................................... 23

Using the TOOLS Button

............................................................ 24

Memorizing the Channels

........................................................... 24

To Select the Source

.................................................................. 26

To Edit the Input Source Name

.................................................. 26

PICTURE CONTROL

Changing the Picture Standard .................................................. 27

Customizing the Picture Settings

............................................... 27

Adjusting the Detailed Settings

.................................................. 28

Conguring Picture Options

....................................................... 31

Resetting the Picture Settings to the Factory Defaults

............... 34

SOUND CONTROL

Changing the Sound Standard ................................................... 35

Customizing the Sound

.............................................................. 35

Setting the TruSurround XT

........................................................ 36

Choosing a Multi-Channel Sound (MTS) track - Digital

............. 36

Choosing a Multi-Channel Sound (MTS) track - Analog

............ 37

Automatic Volume Control

.......................................................... 37

Setting the TV Speakers On/Off

................................................. 38

Connecting Headphones (Sold separately)

................................ 38

■

CHANNEL CONTROL

Clearing Scrambled Channels - Digital ...................................... 39

Adding and Erasing Channels

.................................................... 40

To Set-Up Your Favorite Channels

............................................. 41

Using the Channel Lists - Analog

............................................... 42

Viewing the Channel Lists

.......................................................... 42

Labeling Channels

...................................................................... 43

Fine Tuning Analog Channels

.................................................... 44

Checking the Digital-Signal Strength

.......................................... 44

PC DISPLAY

Using Your TV as a Computer (PC) Display ............................... 45

Display Modes

............................................................................ 45

Setting up the TV with your PC

.................................................. 46

TIME SETTING

Setting the Clock ........................................................................ 48

FUNCTION DESCRIPTION

Selecting a Menu Language ....................................................... 51

Using the V-Chip

........................................................................ 52

Viewing Closed Captions (On-Screen Text Messages)

- Analog ...................................................................................... 59

Viewing Closed Captions (On-Screen Text Messages)

- Digital ....................................................................................... 60

Adjusting the TV On/Off Melody Sound...................................... 61

Setting the Entertainment mode

................................................. 61

Using the Energy Saving Feature

.............................................. 62

Upgrading the Software

.............................................................. 62

ABOUT ANYNET+

What is Anynet

+

? ....................................................................... 63

Connecting Anynet

+

Devices ...................................................... 63

Setting Up Anynet

+

..................................................................... 64

Scanning and Switching between Anynet

+

Devices ................... 64

Recording

................................................................................... 65

Listening through a Receiver (Home theater)

............................ 66

Troubleshooting for Anynet

+

....................................................... 66

APPENDIX

Troubleshooting .......................................................................... 67

Installing the Stand

..................................................................... 69

Disconnecting the Stand

............................................................ 69

Auto Wall-Mount Adjustment (Sold separately)

(LN32A450C1D, LN37A450C1D, LN40A450C1D) ..................70

Wall Mount Kit Specications (VESA)

........................................ 71

Using the Anti-Theft Kensington Lock

........................................ 72

Specications

............................................................................. 73

Dimensions

................................................................................. 74

■

English - 1

Symbol Press Note One-Touch

Button

BN68-01395A-Eng-0202.indd 1 2008-02-20 ¿ÀÀü 6:11:15

English - 2

Accessories

Please make sure the following items are included with your LCD TV.

If any items are missing, contact your dealer.

Remote Control & Batteries (AAA x 2)

(BN59-00687A)

Power Cord

(3903-000144)

Cleaning Cloth

(BN63-01798A)

Cover-Bottom

(LN26A450C1D: BN63-04269A)

(LN32A450C1D: BN63-04269A)

(LN37A450C1D: BN63-04243A)

(LN40A450C1D: BN63-04243A)

Owner’s Instructions

Warranty Card / Registration Card /

Safety Guide Manual

(Not available in all locations)

Stand

(LN26A450C1D: BN96-06463E)

(LN32A450C1D: BN96-06464A)

(LN37A450C1D: BN96-07182A)

(LN40A450C1D: BN96-07182A)

Stand Screw (M4 X L16)

(6002-001294)

Stand Screw (M4 X L14)

(LN32A450C1D : 6003-001334)

(LN37A450C1D : 6003-001334)

(LN40A450C1D : 6003-001334)

The items color and shape may vary depending on the model.

General Information

List of Features

 Adjustable picture settings that can be stored in the TV’s memory.

 Automatic timer to turn the TV on and off.

 A special sleep timer.

 Excellent Digital Interface & Networking :

With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver

(Set-Top Box) needed.

 HDMI/DVI connection of your PC to this TV.

 Excellent Picture Quality

- DNIe technology provides life-like clear images.

 SRS TruSurround XT

- SRS TruSurround XT provides a virtual surround system.

BN68-01395A-Eng-0202.indd 2 2008-02-20 ¿ÀÀü 6:11:18

English - 3

Viewing the Control Panel

Buttons on the Lower-Right Part of the Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

1

SOURCE

Toggles between all the available input sources

(TV, AV1, AV2, S-Video, Component1, Component2,

PC, HDMI1, HDMI2, HDMI3).

In the on-screen menu, use this button as you would

use the ENTER button on the remote control.

2

MENU

Press to see an on-screen menu of your TV’s features.

3

+ VOL -

Press to increase or decrease the volume.

In the on-screen menu, use the + VOL - buttons as you

would use the ◄ and ► buttons on the remote control.

4 < CH >

Press to change channels.

In the on-screen menu, use the

<

CH

>

buttons as you

would use the ▼ and ▲ buttons on the remote control.

5

(POWER)

Press to turn the TV on and off.

6

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

7

POWER INDICATOR

Blinks and turns off when the power is on and

lights up in stand-by mode.

8

SPEAKERS

The product color and shape may vary depending on the model.

Side Panel buttons

1

2

3

4

5

6

7

88

BN68-01395A-Eng-0202.indd 3 2008-02-20 ¿ÀÀü 6:11:20

English - 4

Viewing the Connection Panel

Use the connection panel jacks to connect A/V components that will be connected continuously, such as DVD players or a VCR.

For more information on connecting equipment, see pages 7~20.

The product color and shape may vary depending on the model.

[TV Side Panel]

LN26A450C1D, LN40A450C1D

[TV Side Panel]

LN32A450C1D, LN37A450C1D

[TV Rear Panel]

BN68-01395A-Eng-0202.indd 4 2008-02-20 ¿ÀÀü 6:11:20

English - 5

1

AUDIO OUT

Connects to the audio input jacks on your Amplifier/Home theater.

2

DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component.

3

PC IN [PC] / [AUDIO]

Connects to the video and audio output jacks on your PC.

4

HDMI IN 1, 2, 3 / DVI IN(HDMI2)[R-AUDIO-L] (LN26A450C1D, LN40A450C1D)LN26A450C1D, LN40A450C1D)

Connects to the HDMI jack of a device with an HDMI output.

Use the HDMI IN 2 jack for DVI connection to an external device.

Use a DVI to HDMI cable or DVI-HDMI adapter (DVI to HDMI) for video connection and the

DVI IN (HDMI2) [R-AUDIO-L] jacks for audio.

- No sound connection is needed for an HDMI to HDMI connection.

- When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.

5

HDMI IN 1, 2, 3 / DVI IN(HDMI1)[R-AUDIO-L] (LN32A450C1D, LN37A450C1D)LN32A450C1D, LN37A450C1D)

Connects to the HDMI jack of a device with an HDMI output.

Use the HDMI IN 1 jack for DVI connection to an external device.

Use a DVI to HDMI cable or DVI-HDMI adapter (DVI to HDMI) for video connection and the

DVI IN (HDMI1) [R-AUDIO-L] jacks for audio.

- No sound connection is needed for an HDMI to HDMI connection.

- When using an HDMI/DVI cable connection, you must use the HDMI IN 1 jack.

6

ANT IN

Connects to an antenna or cable TV system.

7

AV IN 2

Video and audio inputs for external devices, such as a camcorder or VCR.

S-VIDEO

Connects an S-Video signal from a camcorder or VCR.

8

(HEADPHONE)

Connects a set of external headphones for private listening.

9

POWER INPUT

Connects the supplied power cord.

0

SERVICE

Connector for SERVICE only.

!

COMPONENT IN 1, 2

The COMPONENT IN 1 jack is also used as the AV IN 1 jack.

- Connect the video cable to the COMPONENT IN 1 [Y/VIDEO] jack and the audio cable to the

COMPONENT IN 1 [R-AUDIO-L] jacks.

@

EX-LINK

- LN26A450C1D

Connector for SERVICE only.

- LN32A450C1D / LN37A450C1D / LN40A450C1D

Connect this to the jack on the optional wall mount bracket. This will allow you to adjust the TV viewing angle using

your remote control.

#

KENSINGTON LOCK

The Kensington Lock (optional) is a device used to physically fix the system when used in a public place.

If you want to use a locking device, contact the dealer where you purchased the TV.

The location of the Kensington Lock may be different depending on its model.

BN68-01395A-Eng-0202.indd 5 2008-02-20 ¿ÀÀü 6:11:21

English - 6

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

The performance of the remote control may be affected by bright light.

1

POWER

Turns the TV on and off.

2

TV

Selects the TV mode directly.

3

NUMERIC BUTTONS

Press to change the channel.

4

Press to select additional

channels(digital and analog) being

broadcast by the same station.

For example, to select channel

“54-3”, press “54”, then press “

”

and “3”.

5 (

MUTE)

Press to temporarily cut off the

sound.

6

VOL

/ VOL

Press to increase or decrease

the volume.

7

CH LIST

Used to display Channel Lists on

the screen.

8

TOOLS

Use to quickly select frequently

used functions.

9

INFO

Press to display information on

the TV screen.

0

COLOR BUTTONS

Use these buttons in the

Channel list, etc.

!

SRS

Selects SRS TruSurround XT

mode.

@

E.MODE

Press to select the preset

display and sound modes for

sports, cinema and games.

#

Use these buttons in the DMA and

Anynet+ modes.

(

: This remote can be used

to control recording on Samsung

recorders with the Anynet

+

feature)

$

SOURCE

Press to display and select the

available video sources.

%

PRE CH

Tunes to the previous channel.

^

CH

/ CH

Press to change channels.

&

MENU

Displays the main on-screen

menu.

*

CC

Controls the caption decoder.

(

RETURN

Returns to the previous menu.

)

UP▲ / DOWN▼ / LEFT◄

/

RIGHT►

/ ENTER

Use to select on-screen menu

items and change menu values.

a

EXIT

Press to exit the menu.

b

DMA (Digital Media Adapter)

Use this when connecting a

SAMSUNG DMA device through

an HDMI interface and switching

to DMA mode.

For more information on the

operating procedures, refer to

the user manual of the DMA.

This button is available when

“Anynet

+

(HDMI-CEC)” is “On”

(see page 64)

c

MTS

Press to choose stereo, mono

or Separate Audio Program

(SAP broadcast).

d

FAV.CH

Press to switch to your favorite

channels.

e

P.SIZE

Picture size selection.

BN68-01395A-Eng-0202.indd 6 2008-02-20 ¿ÀÀü 6:11:22

English - 7

1. Lift the cover at the back of the remote control upward as shown in the figure.

2. Install two AAA size batteries.

Make sure to match the "+" and "–" ends of the batteries with the diagram inside the compartment.

3. Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a

long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries should last for about one year.)

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Installing Batteries in the Remote Control

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see "Antennas with

300 Ω Flat Twin Leads" below.

If your antenna has one lead that looks like the diagram to the right, see "Antennas with 75

Ω Round Leads".

If you have two antennas, see "Separate VHF and UHF Antennas".

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter

(not supplied).

Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

ANT IN

Antennas with 300 Ω Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or "rabbit ears") that has 300 Ω twin at leads, follow the directions

below.

1. Plug the antenna lead into the ANT IN terminal on the back of the TV.

Antennas with 75 Ω Round Leads

ANT IN

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before

connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

UHF

VHF

ANT IN

UHF

VHF

Connections (LN26A450C1D, LN40A450C1D)

BN68-01395A-Eng-0202.indd 7 2008-02-20 ¿ÀÀü 6:11:24

English - 8

After you have made this connection, set the A/B switch to the "A" position for normal viewing. Set the A/B switch to the "B" position to

view scrambled channels. (When you set the A/B switch to "B", you will need to tune your TV to the cable box’s output channel, which is

usually channel 3 or 4.)

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-

way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)

1.

Find and disconnect the cable that is

connected to the ANT IN terminal on your

cable box.

This terminal might be labeled "ANT IN",

"VHF IN" or simply, "IN".

2. Connect this cable to a two-way splitter.

3. Connect an RF cable between the

OUTPUT

terminal on the splitter and the IN terminal

on the cable box.

4. Connect an RF cable between the

ANT OUT terminal on the cable box and

the B–IN terminal on the RF(A/B) switch.

5. Connect another cable between the other

OUT terminal on the splitter and the A–IN

terminal on the RF (A/B) switch.

6. Connect the last RF cable between the

OUT terminal on the RF (A/B) switch and

the ANT IN terminal on the rear of the TV.

Splitter

Incoming

cable

Splitter

Cable Box

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

ANT IN

Splitter

Cable Box

Incoming

cable

RF (A/B)

Switch

Splitter

Cable Box

Incoming

cable

TV Rear

RF (A/B)

Switch

ANT IN

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1. Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

ANT OUT

ANT IN

BN68-01395A-Eng-0202.indd 8 2008-02-20 ¿ÀÀü 6:11:26

English - 9

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back

panel configuration.

When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match

the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.

1. Connect an HDMI Cable

between the HDMI IN (1, 2

or 3) jack on the TV and the

HDMI jack on the DVD Player

or Cable Box/Satellite receiver

(Set-Top Box).

1. Connect a DVI to HDMI Cable

or DVI-HDMI Adapter between

the HDMI IN 2 jack on the TV

and the DVI jack on the DVD

Player or Cable Box/Satellite

receiver (Set-Top Box).

2. Connect Audio Cables

between the DVI IN (HDMI 2)

[R-AUDIO-L] jack on the TV

and the DVD Player or Cable

Box/Satellite receiver (Set-Top

Box).

DVD Player or Cable Box/Satellite receiver

(Set-Top Box) Rear Panel

TV Rear Panel

HDMI Cable (Not supplied)

TV Side Panel

or

What is HDMI?

• HDMI(High-Definition Multimedia Interface), is an interface that enables the

transmission of digital audio and video signals using a single cable.

• The difference between HDMI and DVI is that the HDMI device is smaller in

size and has the HDCP (High Bandwidth Digital Copy Protection) coding feature

installed.

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back

panel configuration.

DVD Player or Cable Box/

Satellite receiver (Set-Top Box)

Audio Cable

(Not supplied)

2

DVI to HDMI Cable (Not supplied)1

TV Rear Panel

BN68-01395A-Eng-0202.indd 9 2008-02-20 ¿ÀÀü 6:11:27

English - 10

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD Player or Cable Box/Satellite receiver (Set-Top Box) to your TV.

1. Connect a Component Cable

between the COMPONENT

IN (1 or 2) [Y, PB, PR] jacks on

the TV and the COMPONENT

[Y, PB, PR] jacks on the DVD

Player or Cable Box/Satellite

receiver (Set-Top Box).

2. Connect Audio Cables between

the COMPONENT IN(1 or 2)

[R-AUDIO-L] jacks on the TV

and the AUDIO OUT jacks

on the DVD Player or Cable

Box/Satellite receiver (Set-Top

Box).

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and

Pr (Red) for enhanced video quality.

Be sure to match the component video and audio connections.

For example, if connecting a Component video cable to COMPONENT IN 1, connect the

audio cable to COMPONENT IN 1 also.

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back panel

configuration.

When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match the

color of the connection terminal to the cable.

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

TV Rear Panel

Component Cable (Not supplied)

1

Audio Cable (Not supplied)

2

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV.

They allow you to view the camcorder tapes without using a VCR.

1. Connect a Video Cable

(or S-Video Cable) between

the AV IN 2 [VIDEO] (or

S-VIDEO) jack on the TV

and the VIDEO OUT jack on

the camcorder.

2. Connect Audio Cables

between the AV IN 2

[R-AUDIO-L] jacks on the TV

and the AUDIO OUT jacks

on the camcorder.

Each Camcorder has a different back panel configuration.

When connecting a Camcorder, match the color of the connection terminal to the cable.

TV Side Panel

Camcorder

S-Video Cable (Not supplied)

1

Audio Cable (Not supplied)

2

Video Cable (Not supplied)

1

or

BN68-01395A-Eng-0202.indd 10 2008-02-20 ¿ÀÀü 6:11:29

English - 11

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the

instructions on pages 7~8). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or antenna

from the back of the TV.

2. Connect the cable or antenna to

the ANT IN terminal on the back

of the VCR.

3. Connect an RF Cable between

the ANT OUT terminal on the

VCR and the ANT IN terminal

on the TV.

4. Connect a Video Cable

between the VIDEO OUT jack

on the VCR and the AV IN 1

[Y/VIDEO] or AV IN 2 [VIDEO]

jack on the TV.

5. Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the AV

IN 1 (or AV IN 2) [R-AUDIO-L]

jacks on the TV.

If you have a “mono”

(non-stereo) VCR, use a

Y-connector (not supplied)

to hook up to the right and

left audio input jacks of the

TV. If your VCRis stereo,

you mustm connect two

cables.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not

match the color of the video cable (Yellow).

Your Samsung TV can be connected to an S-Video jack on a VCR.

(This connection delivers a better picture when compared to the regular Video connection above.)

1. To begin, follow steps 1–3

in the previous section to

connect the antenna or

cable to your VCR and your

TV.

2. Connect an S-Video Cable

between the S-VIDEO OUT

jack on the VCR and the

AV IN 2 [S-VIDEO] jack on

the TV.

3. Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the

AV IN 2 [R-AUDIO-L] jacks

on the TV.

An S-Video cable may be included with a VCR. (If not, check your local electronics store.)

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

Video Connection

S-Video Connection

ANT IN

VCR Rear Panel

Video Cable (Not supplied)

4

Audio Cable (Not supplied)

5

RF Cable (Not supplied)3

TV Rear Panel

TV Side Panel

VCR Rear Panel

RF Cable (Not supplied)

1

Audio Cable (Not supplied)

3

TV Rear Panel

S-Video Cable (Not supplied)

2

TV Side Panel

BN68-01395A-Eng-0202.indd 11 2008-02-20 ¿ÀÀü 6:11:31

English - 12

Connecting an Amplier/DVD Home Theater

1. Connect Audio Cables

between the AUDIO OUT

[R-AUDIO-L] jacks on the TV

and AUDIO IN [R-AUDIO-L]

jacks on the Amplifier/DVD

Home Theater.

When an audio amplifier is

connected to the "AUDIO OUT

[R-AUDIO-L]" jacks: Decrease

the volume of the TV and

adjust the volume level with

the Amplifier’s volume control.

Amplier/DVD Home Theater

TV Rear Panel

Audio Cable (Not supplied)

Each Amplifier/DVD Home Theater has a different back panel configuration.

When connecting an Amplifier/DVD Home Theater, match the color of the connection

terminal to the cable.

Connecting a Digital Audio System

1. Connect an Optical Cable

between the “DIGITAL AUDIO

OUT (OPTICAL)” jacks on the

TV and the Digital Audio Input

jacks on the Digital Audio

System.

When a Digital Audio System

is connected to the “DIGITAL

AUDIO OUT (OPTICAL)” jack:

Decrease the volume of the

TV and adjust the volume

level with the system’s volume

control.

Digital Audio System

TV Rear Panel

Optical Cable (Not supplied)

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

Each Digital Audio System has a different back panel configuration.

When the receiver (home theater) is set to On, you can hear sound output from the TV’s

Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 chan-

nel sound to the Home theater receiver. When the source is a digital component such as

a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the

Home Theater receiver. If you want to hear 5.1 channel audio, connect the DIGITAL AUDIO

OUT (OPTICAL) jack on the DVD player or Cable/Satellite Box directly to an Amplifier or

Home Theater, not the TV.

The rear panel jacks on your TV make it easy to connect a Digital Audio System (Home theater/Receiver) to your TV.

BN68-01395A-Eng-0202.indd 12 2008-02-20 ¿ÀÀü 6:11:32

English - 13

Connecting a PC

Using the D-Sub Cable

1. Connect a D-Sub Cable

between PC IN [PC] connector

on the TV and the PC output

connector on your computer.

2. Connect a PC Audio Cable

between the PC IN [AUDIO]

jack on the TV and the Audio

Out jack of the sound card on

your computer.

Using the HDMI/DVI Cable

1. Connect a HDMI/DVI cable

between the HDMI IN 2 jack

on the TV and the PC output

jack on your computer.

2. Connect a 3.5 mm Stereo

mini-plug/2RCA Cable

between the DVI IN(HDMI2)

[R-AUDIO-L] jack on the TV

and the Audio Out jack of the

sound card on your computer.

PC

TV Rear Panel

D-Sub Cable (Not supplied)

1

PC Audio Cable (Not supplied)2

Each PC has a different back panel configuration.

When connecting a PC, match the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.

3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)

2

HDMI/DVI Cable (Not supplied)1

TV Rear Panel

PC

BN68-01395A-Eng-0202.indd 13 2008-02-20 ¿ÀÀü 6:11:35

English - 14

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see "Antennas with

300 Ω Flat Twin Leads" below.

If your antenna has one lead that looks like the diagram to the right, see "Antennas with 75

Ω Round Leads".

If you have two antennas, see "Separate VHF and UHF Antennas".

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter

(not supplied).

Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

ANT IN

Antennas with 300 Ω Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or "rabbit ears") that has 300 Ω twin at leads, follow the directions

below.

1. Plug the antenna lead into the ANT IN terminal on the back of the TV.

Antennas with 75 Ω Round Leads

ANT IN

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before

connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.

UHF

VHF

ANT IN

UHF

VHF

Connections (LN32A450C1D, LN37A450C1D)

BN68-01395A-Eng-0202.indd 14 2008-02-20 ¿ÀÀü 6:11:35

English - 15

After you have made this connection, set the A/B switch to the "A" position for normal viewing. Set the A/B switch to the "B" position to

view scrambled channels. (When you set the A/B switch to "B", you will need to tune your TV to the cable box’s output channel, which is

usually channel 3 or 4.)

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-

way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)

1.

Find and disconnect the cable that is

connected to the ANT IN terminal on your

cable box.

This terminal might be labeled "ANT IN",

"VHF IN" or simply, "IN".

2. Connect this cable to a two-way splitter.

3. Connect an RF cable between the

OUTPUT

terminal on the splitter and the IN terminal

on the cable box.

4. Connect an RF cable between the

ANT OUT terminal on the cable box and

the B–IN terminal on the RF(A/B) switch.

5. Connect another cable between the other

OUT terminal on the splitter and the A–IN

terminal on the RF (A/B) switch.

6. Connect the last RF cable between the

OUT terminal on the RF (A/B) switch and

the ANT IN terminal on the rear of the TV.

Splitter

Incoming

cable

Splitter

Cable Box

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

ANT IN

Splitter

Cable Box

Incoming

cable

RF (A/B)

Switch

Splitter

Cable Box

Incoming

cable

TV Rear

RF (A/B)

Switch

ANT IN

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1. Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

ANT OUT

ANT IN

BN68-01395A-Eng-0202.indd 15 2008-02-20 ¿ÀÀü 6:11:36

English - 16

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different

back panel configuration.

When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box),

match the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection, you must use the HDMI IN 1 jack.

1. Connect an HDMI Cable between

the HDMI IN (1, 2 or 3) jack on the

TV and the HDMI jack on the

DVD Player or Cable Box/Satellite

receiver (Set-Top Box).

1. Connect a DVI to HDMI Cable or

DVI-HDMI Adapter between the

HDMI IN 1 jack on the TV and the

DVI jack on the DVD Player or Cable

Box/Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the

DVI IN (HDMI 1) [R-AUDIO-L] jack

on the TV and the DVD Player or

Cable Box/Satellite receiver (Set-Top

Box).

DVD Player or Cable Box/Satellite

receiver (Set-Top Box) Rear Panel

TV Rear Panel

HDMI Cable (Not supplied)

TV Side Panel

or

What is HDMI?

• HDMI(High-Definition Multimedia Interface), is an interface that enables the

transmission of digital audio and video signals using a single cable.

• The difference between HDMI and DVI is that the HDMI device is smaller

in size and has the HDCP (High Bandwidth Digital Copy Protection) coding

feature installed.

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different

back panel configuration.

DVD Player or Cable Box/

Satellite receiver (Set-Top Box)

Audio Cable

(Not supplied)

2

DVI to HDMI Cable (Not supplied)1

TV Rear Panel

BN68-01395A-Eng-0202.indd 16 2008-02-20 ¿ÀÀü 6:11:38

English - 17

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD Player or Cable Box/Satellite receiver (Set-Top Box) to your TV.

1. Connect a Component Cable

between the COMPONENT IN

(1 or 2) [Y, PB, PR] jacks on the TV

and the COMPONENT [Y, PB, PR]

jacks on the DVD Player or Cable

Box/Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the

COMPONENT IN(1 or 2)

[R-AUDIO-L] jacks on the TV

and the AUDIO OUT jacks on the

DVD Player or Cable Box/Satellite

receiver (Set-Top Box).

Component video separates the video into Y (Luminance (brightness)), Pb (Blue)

and Pr (Red) for enhanced video quality. Be sure to match the component video and

audio connections.

For example, if connecting a Component video cable to COMPONENT IN 1,

connect the audio cable to COMPONENT IN 1 also.

Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back

panel configuration.

When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match the

color of the connection terminal to the cable.

DVD Player or Cable Box /

Satellite receiver (Set-Top Box)

TV Rear Panel

Component Cable (Not supplied)

1

Audio Cable (Not supplied)

2

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV.

They allow you to view the camcorder tapes without using a VCR.

1. Connect a Video Cable

(or S-Video Cable) between the

AV IN 2 [VIDEO] (or S-VIDEO)

jack on the TV and the VIDEO

OUT jack on the camcorder.

2. Connect Audio Cables between

the AV IN 2 [R-AUDIO-L] jacks

on the TV and the AUDIO OUT

jacks on the camcorder.

Each Camcorder has a different back panel configuration.

When connecting a Camcorder, match the color of the connection terminal to the

cable.

TV Side Panel

Camcorder

S-Video Cable (Not supplied)

1

Audio Cable (Not supplied)

2

Video Cable (Not supplied)

1

or

BN68-01395A-Eng-0202.indd 17 2008-02-20 ¿ÀÀü 6:11:39

English - 18

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the

instructions on pages 14~15). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or antenna from

the back of the TV.

2. Connect the cable or antenna to the

ANT IN terminal on the back of the

VCR.

3. Connect an RF Cable between the

ANT OUT terminal on the VCR and

the ANT IN terminal on the TV.

4. Connect a Video Cable between the

VIDEO OUT jack on the VCR and

the AV IN 1 [Y/VIDEO] or AV IN 2

[VIDEO] jack on the TV.

5. Connect Audio Cables between the

AUDIO OUT jacks on the VCR and

the AV IN 1 (or AV IN 2)

[R-AUDIO-L] jacks on the TV.

If you have a “mono”(non-stereo)

VCR, use aY-connector (not

supplied) to hook up to the right

and left audio input jacks of the

TV. If your VCR is stereo, you

must connect two cables.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does

not match the color of the video cable (Yellow).

Your Samsung TV can be connected to an S-Video jack on a VCR.

(This connection delivers a better picture when compared to the regular Video connection above.)

1. To begin, follow steps 1–3 in the

previous section to connect the

antenna or cable to your VCR and

your TV.

2. Connect an S-Video Cable

between the S-VIDEO OUT jack

on the VCR and the AV IN 2

[S-VIDEO] jack on the TV.

3. Connect Audio Cables between

the AUDIO OUT jacks on the VCR

and the AV IN 2 [R-AUDIO-L]

jacks on the TV.

An S-Video cable may be included with a VCR. (If not, check your local electronics store.)

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

Video Connection

S-Video Connection

ANT IN

VCR Rear Panel

Video Cable (Not supplied)

4

Audio Cable (Not supplied)

5

RF Cable (Not supplied)3

TV Rear Panel

TV Side Panel

VCR Rear Panel

RF Cable (Not supplied)

1

Audio Cable (Not supplied)

3

TV Rear Panel

S-Video Cable (Not supplied)

2

TV Side Panel

BN68-01395A-Eng-0202.indd 18 2008-02-20 ¿ÀÀü 6:11:40

La page charge ...

Samsung LN40A450 Manuel utilisateur

Samsung LN40A450 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents