Bradford White BNTH-105 Manuel utilisateur

Marque: Bradford White

Modèle: BNTH-105

Taper: Manuel utilisateur

Ce manuel convient également à

User’s Manual Doc. 1260B

User’s Manual for

Modulating Boiler

Model BNTH

Sizes 080-210 MBTU/h

H2360200B

WARNING

If the information in this manual is not

followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

Do not store or use gasoline or other

ammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

nearby phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the re department.

Installation and service must be performed

by a qualied installer, service agency, or gas

supplier.

FOR YOUR SAFETY: This product must be installed and serviced by a professional service technician,

qualied in hot water boiler and heater installation and maintenance. Improper installation and/or operation

could create carbon monoxide gas in ue gases which could cause serious injury, property damage, or

death. Improper installation and/or operation will void the warranty.

AVERTISSEMENT

Assurez-vous de bien suivres les instructions

données dans cette notice pour réduire au

minimum le risque d’incendie ou d’explosion ou

pour éviter tout dommage matériel, toute blessure

ou la mort.

Ne pas entreposer ni utiliser d’essence ni

d’autres vapeurs ou liquides inammables dans

le voisinage de cet appareil ou de tout autre

appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareils.

• Ne touchez à aucun interrupteur. Ne pas vous

servir des téléphones dansle bâtiment où vous

vous trouvez.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions

du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de

gaz, appelez le sservice des incendies.

L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualié ou

par le fournisseur de gaz.

Brute

Page 1

RADFORD

HITE

Switched these because of stupid page layout system.

CONTENTS

Familiarizing yourself to the Bradford White Brute ...........1

FOR YOUR SAFETY,

PLEASE READ THIS BEFORE OPERATING.............2

What to Do If You Smell Gas .............................................2

POUR VOTRE SÉCURITÉ,

LISEZ AVANT DE METTRE EN MARCHE ....................2

Que Faire si Vous Sentez une Odeur de Gaz ......................2

Lighting the Unit ................................................................. 3

Turning O the Gas to the Unit ..........................................3

Instructions de Mise en Marche .......................................... 4

Fermeture de l’Alimentation en Gaz ...................................4

Shutting Down the Bradford White Brute ..........................5

Restarting the Bradford White Brute ..................................5

In the Event of Power Failure .............................................5

THE USER INTERFACE AND ON/OFF SWITCH .......... 6

About Lockouts, Holds, and Alerts ................................... 10

Care, Inspection, and Service ............................................11

FAMILIARIZING YOURSELF TO THE

Brute

Shown without jacket. Internal components will vary slightly between sizes, but the User Interface & On/O Switch remain the same.

ON/OFF SWITCH

USER

INTERFACE

Sizes available are 080-210 MBTU/h. This illustration is of the 150 -210 MBTU/h

EXHAUST VENT CONNECTION

GAS CONNECTION

AIR PRESSURE SWITCH

HEAT EXCHANGER

GAS VALVE

VENTURI

AIR/ GAS

BLOWER

PRESSURE RELIEF VALVE

WATER INLET

WATER OUTLET

AIR INLET CONNECTION

DRAIN VALVE

CONDENSATE TRAP

AIR TRANSITION

Page 2

RUTE. HIGH EFFICIENCY RESIDENTIAL BOILERS

Brute

Switched these because of stupid page layout system.

FOR YOUR SAFETY -

PLEASE READ THIS BEFORE OPERATING

WARNING

If you do not follow these instructions exactly, a re or explosion may result,

causing property damage, personal injury or loss of life.

A. This unit does not have a pilot. It is equipped with an ignition device which automatically lights the burner. Do

not try to light the burner by hand.

B. Before operating the unit, check for any smell of gas in the area around it. Be sure to smell next to the oor,

because some gas is heavier than air and will settle near the oor.

C. Use only your hand to turn the handle on the gas valve. Never use tools. If the valve handle will not turn by

hand, don’t try to repair it. Call a qualied service technician. If you force the valve or try to repair it, this

may result in a re or explosion.

D. Do not use this unit if any part has been under water. Immediately call a qualied service technician to inspect

the unit. Any part of the control system or any gas control which has been under water must be replaced.

WHAT TO DO IF YOU SMELL GAS

· Do not try to light any appliance or device that uses gas.

· Do not touch any electrical switch. Do not use any phone in your building.

· Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

· If you cannot reach your gas supplier, call the re department.

POUR VOTRE SÉCURITÉ,

LISEZ AVANT DE METTRE EN MARCHE

AVERTISSEMENT

Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque un

début d’ incendie ou une explosion entraînant des dommages, des blessures ou la mort.

A. Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse. Ne tentez pas

d’allumer la veilleu manuellement.

B. Avant de faire fonctionner, reniez tout autour de l’appareil pour déceler une odeur de gaz. Reniez près du

plancher, car certains gaz sont plus lourds que l’air et peuvent s’accumuler au niveau du sol.

C. N’utilisez que votre main pour fermer la soupape d’arrêt de gaz. N’utilisez jamais d’outils. Si la poignêe de

la valve ne tourne pas manuellement, ne tentez pas de la réparer. Communiquez avec un technicien de service

qualié. Le fait de forcer ou de tenter de réparer la poignée pourrait causer un incendie ou une explosion.

D. N’utilisez pas cet appareil s’il a été plongé dans I’eau, même partiellement. Faites inspecter I’appareil par un technicien

qualié et remplacez toute partie du système de contrôle et toute commande qui ont été plongées dans I’eau.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ

· Ne pas tenter d’allumer d’appareil.

· Ne toucher à aucun interrupteur; ne pas vous servir des téléphones se trouvant dans le bâtiment.

· Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les instructions du fournisseur.

· Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies.

Page 3

RADFORD

HITE

Switched these because of stupid page layout system.

LIGHTING THE UNIT

1. STOP! Read the safety information listed above.

2. Set the thermostat to the lowest setting.

3. Turn o all electric power to the unit.

4 This unit is equipped with an ignition device which automatically lights the burner.

Do not try to light the burner by hand.

5. Remove the front access panel.

6 Turn o the manual gas valve. The valve is o when the valve handle is at a right

angle to the gas pipe.

7. Wait ve minutes to allow any gas to clear. Smell for gas, including the area near

the oor. If you do smell gas, STOP! Follow Step B in the safety information listed

above. If you don’t smell gas, go to the next step.

8. Slowly turn the manual gas valve to “ON.” The handle on the valve will be parallel

to the gas pipe.

9. Replace the front panel.

10. Turn on the electric power to the unit.

11. Set the thermostat to the desired setting.

12. If the unit will not operate, follow the instructions in “Turning O the Gas to the

Unit” and call your service technician or gas supplier.

Gas inlet

Manual gas valve

shown in the

O position

TURNING OFF THE GAS TO THE UNIT

1. Before doing any service work, turn o all electric power to

the unit.

2. Set the thermostat to the lowest setting.

3. Remove the front access panel.

4. Turn o the manual gas valve. The valve is o when the

valve handle is at a right angle to the gas pipe.

5. Replace the front panel.

Manual Gas Valve

Page 4

RUTE. HIGH EFFICIENCY RESIDENTIAL BOILERS

Brute

Switched these because of stupid page layout system.

INSTRUCTIONS DE MISE EN MARCHE

1. ARRÊTEZ ! Lisez les instructions de sécurité sur la portion supérieure.

2. Réglez le thermostat à la temperature la plus basse.

3. Coupez l’alimentation électrique de l’appareil.

4. Cet appareil est dote d’un dispositif d’allumage qui allumera automatiquement le

brûleur. Ne tentez pas d’allumer le brûleur manuellement.

5. Retirez le couvercle avant.

6. Mettez la soupape d’ arrêt de gaz à „OFF”. La valve est en position „OFF” lorsque la

poignée se trouve à angle droit du tuyau de gaz.

7 Attendez cinq minutes an que le gaz se dissipe. Si vous croyez sentir une odeur de

gaz, ARRÊTEZ ! Reportez-vous aux instructions B ci-dessus, sur cette étiquette. S’il

n’y a pas d’odeur de gaz, passez à la prochaine étape.

8. Remettez lentement la soupape d’arrêt de gaz en position „ON”. La poignée sera

parallèle au tuyau de gaz.

9. Replacez le couvercle avant.

10. Rétablissez l’alimentation électrique à l’appareil.

11. Réglez le thermostat à la température désirée.

12. Si l’appareil ne fonctionne pas, suivez les directives relatives à la fermeture de

l’alimentation en gaz et communiquez avec votre technicien de service ou le

fournisseur de gaz.

Entrée

de gaz

Valve de gaz manuel le se

trouvant en position„OFF”.

FERMETURE DE L’ALIMENTATION EN GAZ

1. Coupez toute alimentation électrique à l’appareil si celui-

ci doit faire l’objet d’un entretien.

2. Réglez le thermostat au réglage le plus bas.

3. Retirez le couvercle d’accès au panneau de commande.

4. Mettez la soupape d’arrêt de gaz à „OFF”. La valve est

en position „OFF“ lorsque la poignée se trouve à angle

droit du tuyau de gaz.

5. Replacez le couvercle d’accès au panneau de commande.

Valve de Gaz Manuel

Page 5

RADFORD

HITE

Switched these because of stupid page layout system.

SHUTTING DOWN THE BRADFORD WHITE BRUTE

It may sometimes be necessary to shut down the Bradford White Brute. Here are the steps

required to do this:

1. Switch o the main electrical disconnect switch.

2. Open the front cover and close the main manual gas valve.

3. If freezing is anticipated, drain the Bradford White Brute. (Also be sure to protect the

piping in the building from freezing.)

The steps listed above may require qualied service personnel.

RESTARTING THE BRADFORD WHITE BRUTE

It may be necessary to restart the Bradford White Brute – for example, after a power

interruption. Here are the steps required to do this:

1 Reset any errors using the user interface. See the section on “About Lockouts, Holds,

and Alerts.”

2 Turn up the thermostat to call for heat.

3. In approximately 2 seconds, the blower will operate. Ignition should occur after 35-40

seconds. It may take as long as 2-1/2 minutes.

4. If ignition does not occur, wait 5 minutes and then repeat steps 1 through 3.

5. If, after three attempts, the unit still does not light, shut down the boiler and call your

service technician.

If the unit has been drained, follow these steps:

1. See the “Installation and Operation Manual” for instructions on lling and purging the

unit.

2. Remove the front door. Turn on the gas shuto valve.

3. Switch on the main electrical disconnect switch. The pump and blower will start, and

the igniter will be energized. After 35 seconds the gas valve will be energized, and

ignition will occur. If ignition does not occur within 2-1/2 minutes switch “o” the

main disconnect switch, wait 5 minutes and switch it “on” again. If after three attempts

ignition does not occur, shut down the unit and call for service.

IN THE EVENT OF POWER FAILURE

The Bradford White Brute will not operate during an electrical power outage. If there is

an extended power outage with danger of freezing, then the Bradford White Brute (and all

other water systems) should be completely drained. Before draining the unit, turn o the

gas and turn o the main power switch. When you replace the unit in service, refer to the

“Installation and Operation Manual” for instructions on lling and purging.

Page 6

RUTE. HIGH EFFICIENCY RESIDENTIAL BOILERS

Brute

Switched these because of stupid page layout system.

THE USER INTERFACE AND ON/OFF SWITCH

The Bradford White Brute has two control components:

• the User Interface or HMI (“Human/ Machine Interface”).

• the On/O switch

The User Interface (HMI) is used to send commands to the boiler controller and to

display operating and setup information sent from the boiler controller.

The drawing below shows the main parts of the user interface (HMI), and the following

table lists the functions of the various parts of the user interface (HMI).

Display

Up/Down

Arrow

buttons

Left/Right

Arrow

buttons

Back button

Info/Install

button

Home button

Round OK button

User Interface (HMI)

On/O

switch

User Interface

Page 7

RADFORD

HITE

Switched these because of stupid page layout system.

Up/ Down Arrow buttons Use these to go to the choice you want to select in the

display area, then press the round OK button.

Left/ Right Arrow buttons Use these to go to the choice you want to select in the

display area, then press the round OK button.

Back button Use this to go back to the previous display.

Info/ Install button Press this button at any time to go to the sub-menus

that allow you to set up and monitor the controller.

Home button Press this button at any time to go back to the Home

display. (See the section on “Home Display.”)

Round OK button Use the round OK button to conrm a value or action.

Button Functions on User Interface

Home Screen Button

Home Screen

The Home Screen has three sections:

• The upper section of this screen shows the most important operating information. In

this example, the display is showing the system setpoint, the operating temperature,

the outlet and inlet temperatures for the water entering and leaving the boiler, and the

outdoor temperature.

(Note that the ve lines at the top of the screen are customizable, and may be arranged

dierently on your system.)

• The central section shows some additional operating and setup information. In this

case, this area lists the boiler name, boiler state, current demand, and the current

password level (the “access status”).

• The lower section shows any current lockouts, holds, or alerts.

When the boiler is operating normally, the boiler controller will display the Home Screen on the

display. Or you can press the Home Screen Button at any time to get to this Home Screen.

Page 8

RUTE. HIGH EFFICIENCY RESIDENTIAL BOILERS

Brute

Switched these because of stupid page layout system.

Info/Install Button

The Info/Install Button will change the display to show the six sub-menus available.

Info/ Install Screen

• To move from one choice to another, use the Left- and Right-Arrow buttons or the Up-

and Down-Arrow buttons.

• Once you have highlighted the choice you want, press the round OK button.

Here are the functions you can reach from the Info/ Install display screen:

Quick Start This menu gives you an easy way to check or change the

most common settings on the unit.

system requires a password, you can enter it here.

Test These parameters let you turn the burner on and o, and

control the fan and pump speeds.

Advanced Setup The sub-menus listed here allow you to set up most of

the functions on the controller.

Diagnostics Use the Diagnostics to check the status of the sensors

and the digital inputs and outputs. The system also re-

cords a history of lockouts and alarms.

Display Setup You can use this option to adjust the contrast of the dis-

play or change the items which appear at the top of the

Home display.

Page 9

RADFORD

HITE

Switched these because of stupid page layout system.

Quick Start Menu (found in the Info/Install Screen)

Once the unit has been installed and set up, the Quick Start menu provides a simple way

to change the most common settings used in a typical installation.

Quick Start Menu

Example - Changing the CH (Central Heat) Setpoint

Changing the CH Setpoint

• On the Quick Start menu, use the Up- and Down-Arrows to go to the line for CH

Setpoint. Press the large OK button to select the line.

• Use the Up- and Down-Arrow buttons to select the value you want.

• Press the round OK button to enter the new value.

Page 10

RUTE. HIGH EFFICIENCY RESIDENTIAL BOILERS

Brute

Switched these because of stupid page layout system.

ABOUT LOCKOUTS, HOLDS, AND ALERTS

The system responds to three kinds of trouble indications:

• A”lockout” is caused by a serious problem that might involve a safety issue. Once

the controller enters a lockout, the burner will shut down, and will not be allowed

to run again until the cause of the problem is corrected, and you reset the control

system.

• The system may enter a “hold” for a period of time before locking out. This allows

the controller to see if the error becomes resolved prior to the hard lockout.

• An “alert” indicates that some feature of the control system’s operation was not

correct, delayed, or waiting for a response. This does not necessarily indicate a

problem.

If a problem occurs, the system will present a note across the bottom of the screen:

Example - Lockout or Hold Indication

Correct the problem, then press the round OK button to reset the control.

Each error message includes a number. For a more detailed description of each message,

see the “Installation and Operation Manual.”

Page 11

RADFORD

HITE

Switched these because of stupid page layout system.

GENERAL CARE

Keep the area around the Bradford White Brute clear and free from combustible

materials, gasoline and other ammable vapors and liquids. Clean the jacket surfaces

with a damp cloth and mild soap. Do not use ammable cleaning materials. Keep the

vent terminal free of obstructions. Do not pile snow against the vent terminal.

ANNUAL INSPECTION AND SERVICE

You should visually inspect the vent pipe once a year. Should any corrosion or leaks

exist, have the aected parts replaced.

Once each year a qualied service agency should conduct a detailed inspection of all ue

product carrying areas of the boiler and vent system. Follow the service instructions in

the “Installation and Operating Instructions Manual” for the Bradford White Brute.

Caution

Do not use this boiler if any part has been under water.

Immediately call a qualied service technician to inspect the

boiler. Any part of the control system and any gas control

which has been under water must be replaced.

WARNING

If the unit overheats or the gas supply fails to shut o, do

not turn o or disconnect the electrical supply to the pump.

Instead, shut o the gas supply at a location external to the

Bradford White Brute.

En cas de surchaue ou si l’admission de gaz ne peut être

coupée, ne pas couper ni débrancher l’alimentation électrique

de la pompe. Fermer plutôt le robinet d’admission de gaz à

l’extérieur de l’appareil.

FOR SERVICE

Contact your installing contractor, gas utility, Bradford White dealer, or check

www.bradfordwhite.com for the nearest authorized representative in your area.

H2360200B

200 Lafayette St.

Middleville, MI 49333

Warranty: (800) 531-2111

www.BradfordWhite.com

Bradford White BNTH-105 Manuel utilisateur

Marque: Bradford White

Modèle: BNTH-105

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Bradford White BNTH-105 User manual

Bradford White BNTH-105 Manuel utilisateur

Ce manuel convient également à

Bradford White BNTH-105 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents