wattstopper HS-WP-W Guide d'installation
- Taper
- Guide d'installation
Wattstopper
®
Line Voltage Card Key Switch
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 24776 – 09/16 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: HS-150
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
INSTALLATION AND WIRING
1. Make sure that the power has been turned off at the circuit
breaker.
2. Strip insulation off the wires to expose their copper cores to
the length indicated by the “Strip Gauge” shown in Figure 1.
Approximately 1/2“.
3. Connect wires to the HS-150 flying leads as shown in the wiring
diagram (Figure 2).
• Connect the green or non-insulated (copper) GROUND wire
from the circuit to the green terminal on the HS-150.
• Connect the NEUTRAL wire from the circuit to the white wire on
the HS-150.
• Connect the power wire from the circuit box (HOT/LINE) to the
black wire on the HS-150.
• Connect the power wire to the loads to the red wire on the HS-
150.
4. Put the HS-150 in the wall box and secure it to the wall box with
the screws provided.
5. Attach the cover plate.
6. Restore power to the circuit.
SPECIFICATIONS
Voltage ....................................................................120/277VAC, 50/60Hz
Power Consumption ....................................................Maximum 2.1 Watts
Load Rating
@120 VAC ...... 0-1800W tungsten or ballast, 15A receptacle; 1/2 hp
@277 VAC ............................................................... 0-1200W ballast
Egress Time Delay ................................................................... 30 seconds
Environment .......................................................................Indoor use only
Operating Temperature .............................. 32° to 104°F (0° to 40°C)
Humidity .................................................... 95% RH, non-condensing
Card Slot accepts standard size hotel card keys with dimensions
.............................................................2.125”W x 3.375”H x 0.034”D
.............................................. (53.975mm x 85.725mm x 0.8636mm)
Tools Needed
Insulated Screwdriver
Wire Strippers
DESCRIPTION AND OPERATION
The HS-150 is a line voltage card key switch that operates as a master switch to enable or disable power to single-pole electric branch
circuits and loads in a hotel guest room or similar site. When a hotel door entry card key (or the key fob HS-FOB) is inserted in the
HS-150 card slot, the controlled circuits are energized. When the hotel door entry card key (or HS-FOB) is removed, the controlled
circuits will remain energized for 30 seconds more to allow safe egress from the hotel room. After this time delay elapses, they will be
de-energized. To restore power to the room (that is, to the controlled circuits and loads), the occupant will need to reinsert the hotel door
entry card key into the HS-150 card slot.
Lighted Card Slot
To help you locate the HS-150 in a dark room, two green LEDs illuminate the card slot where the hotel door entry card key or the key
fob HS-FOB should be inserted. When the card or HS-FOB is in the slot, the green LEDs are OFF.
WARNING: TURN THE POWER OFF AT THE
CIRCUIT BREAKER BEFORE WIRING.
Removing card key turns OFF power.
Insert card key for power.
Strip Gauge
1/2"
12.7mm
Figure 1: Strip Gauge
Figure 2: Line voltage wiring
White
Neutral
White (Neutral)
Black
Hot/Line
Red
*
(Load)
White
Local OFF
switches
Controlled receptacles
inside the room
Lighting
load
Lighting
load
Lighting
load
* WARNING - To prevent risk of damage to the unit - Do not exceed
the HS-150’s maximum 15 A load rating.
08363r1
Model #
HS-150
Card Key Switch
120-277VAC, 50/60Hz
Relay Output:
0-800W tungsten/ballast,
1/6hp@120VAC
0-1200W ballast, 1/4hp@277VAC
Indoor use only
GROUND
APPLIANCE
CONTROL
88T9
800.879.8585
www.legrand.us/wattstopper
No. 24776 – 09/16 rev. 1
© Copyright 2016 Legrand All Rights Reserved.
© Copyright 2016 Tous droits réservés Legrand.
© Copyright 2016 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
TROUBLESHOOTING
Lighted card slot is OFF; no response from controlled loads in the guest room when card is inserted in slot.
• Make sure the circuit breaker that feeds the HS-150 and hence the controlled guest room loads is on and functioning.
• If the guest room loads are still not energized, turn power off and verify that the HS-150 is wired correctly and that all wire leads are
tightly connected.
• If loads still do not respond properly after following troubleshooting, turn OFF power to the circuit and call Technical Support at
800.879.8585.
Lighted card slot is ON; no response from controlled loads in the guest room when card is inserted in slot or
removed from it.
• Turn power off and verify that the HS-150 is wired correctly and that all wire leads are tightly connected. Turn power back ON.
• If there is still no response from the controlled loads in the guest room, call Technical Support.
When controlling multiple circuits in a room, call Technical Support at 800.879.8585 for diagrams.
ORDERING INFORMATION
Catalog Number Description
HS-150 Line Voltage Card Key Switch; 120/277VAC, 50/60Hz
HS-100 Low Voltage Card Key Switch; 24VDC/VAC
HS-FOB* Key Fob accessory for use when room access uses a standard key entry or other system without standard size
hotel card key
HS-WP** Cover plate for single-gang box
HS-WPR Cover plate for triple-gang box with decorator switch option (card slot on the right)
HS-WPL Cover plate for triple-gang box with decorator switch option (card slot on the left)
Hotel Card Key Switches, Key Fobs and Cover Plates are available in White (-W), Light Almond (-LA), Ivory (-I), Black (-B), and Grey (-G)
* Not needed when hotel uses card key entry system.
** One HS-WP included with each switch.
-
1
-
2
wattstopper HS-WP-W Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
wattstopper HS-100 Low Voltage Card Key Switch Guide d'installation
-
-
-
-
Legrand PW-101/101-347/201/201-347 Passive Infrared Wall Switch Occupancy Sensor Mode d'emploi
-
Legrand WS-301-347-I Guide d'installation